SlideShare a Scribd company logo
1 of 11
Download to read offline
Embroidery Placement Charts 
 
Hooping Tip:  Mark centers on all 4 sides of your hoop with a fine‐line marker.  Draw lines on 
the wrong side of fabric.  Fold on the lines.  Press fabric into place on hooped hydrostick 
backing, lining up to center marks, unfold, and smooth into place. 
 
   
Embroidery Placement Chart for Shirts
Item  Placement  Other Considerations 
Shirt with no pocket 
Left chest or right chest 
position 
Draw line straight down from 
where shoulder seam meets 
collar seam. 
 
Find center of armholes, from 
armpit to shoulder, and draw 
line straight across.  If you 
place this lint too low, the 
design may go across a 
woman’s breast area. 
 
As an alternative, you can 
draw a horizontal line at the 
level of the second button or 
snap. 
 
On a V‐neck shirt, you can 
draw a horizontal line even 
with the bottom of the V.  
 
Center of design should go 
where the lines intersect. 
If you’re only putting 
embroidery on one side, then 
the name and/or logo should 
go on the left chest position.  
If you’re putting the person’s 
name and logo on two sides, 
the name should go on the 
right, and the logo should go 
on the left.  Rationale:  When 
you shake hands, your eye 
naturally falls to the other 
person’s right shoulder/chest 
area, s if their name is on the 
right, you’re more likely to 
remember it. 
 
Monograms should be ¼ to ½ 
inch tall. 
 
T‐shirt or Sweatshirt 
 
Center Front 
 
Full Front Design 
Center the design from left to 
right. 
Place top of design 2‐4 inches 
down from the neckline. 
Bottom of design shouldn’t go 
below the armpit, but on a 
very large design, it should be 
high enough so it won’t be 
hidden if the shirt is tucked in.
Ladies Sweater, Jacket, Dress, 
or 2 piece outfit with regularly 
placed large designs 
Large irregularly placed 
designs usually follow a 
diagonal or large gentle S 
curve or C curve.  Frequently, 
the design will start at the 
right shoulder, come across 
the bodice, ending at the left 
waist, or curving at center of 
the bodice and ending at the 
left waist.  The design may 
also curve at the waist, and 
come back across the top of 
athe pants or skirt.  
Embroidery sewn on one side, 
The embroidery should be 
placed so it enhances the 
shape of the garment, flatters 
the wearer, and doesn’t get in 
the way of movement. 
 
placed off center and carried 
down the leg, creates a 
vertical line. 
Shirt Center Back  Center the design from left to 
right. 
Center top to bottom with the 
middle of at he armholes, 
from shoulder seam to 
armpit.  
 
Designs should be placed 
lower on sweatshirts with 
hoods. 
Back designs look best when 
placed between the shoulder 
blades, but it’s okay for design 
to go below armpits. 
Collar point  Bottom of monogram should 
be ¼ inch above the top of the 
buttonhole. 
Monograms should e 1/3 to 
3/8 inch high.  The collar may 
need to be removed and 
replaced. 
Turtle Neck Collars  Half way between the center 
neck front and the left 
shoulder seam.  The bottom 
of the design should be ½ to ¾ 
inch above the edge. 
Should be ¼ to 1 inch tall, 
depending on size of collar.  
Follow the direction of the 
edge, don’t try to turn at an 
angle so it’s straight when you 
looking at it. 
Shirt Placket  Centered between 2nd
 and 3rd
 
buttonholes. 
Should be ¼ to 3/8 inches tall. 
Shirt Pocket 
 
For designs that are on the 
pocket itself 
Top of monogram or name 
should be ¼” to ½” from the 
top edge of the pocket, and 
centered between the left 
and right edges of the pocket.
 
Alternately, if the pocket isn’t 
attached, you can put a crest 
or other design on the center 
of the pocket, then attach it 
to the shirt. 
Monograms should be ¼ to 
3/8 inch tall. 
Shirt Sleeves 
Short Sleeves 
Place ¼ to ½ inch above hem 
stitching on edge of sleeve.  
Center design directly 
opposite the underarm seam. 
Monograms should be ¼ to 
3/8 inch tall. 
Shirt Cuffs 
Long Sleeves 
Fold cuff in half, starting with 
button at one side, and 
buttonhole on the other side.  
Monograms should be ¼ to 
3/8 inch tall. 
Edge of monogram should be 
1 inch from the center of cuff, 
towards the buttonhole.  
(Center of monogram should 
be 1 3/8 inches from the 
center.)  The bottom of the 
monogram should be ¼ inch 
above the stitching at the 
bottom edge of the cuff. 
Shirt Euro Tall 
(Front Bottom) 
Bottom of design should be 
1½ inch above stitching for 
lower shirt hem.  Center of 
design should be 2/3rds  of 
the way from the center front 
to the outside left edge 
(approximately 7 inches from 
center). 
Lettering should be ¼ to ½ 
inches tall. 
 
Embroidery Placement Guide for Coats, Jackets, and Robes 
Item  Placement     Other Consideration 
Coat Lining  Approximately waist level, on 
the right side of the coat 
lining, 3 inches from where 
the lining is attached to the 
outer material, near the front 
edge. 
 
Alternatively, it should be 
centered below the inside 
pocket, or in a straight line 
down from where the 
shoulder seam meets the 
collar. 
The monogram or design 
should be at waist level on the 
right side, no matter what the 
length of the coat is. 
Jacket 
Left chest or right chest 
position 
Draw line straight down from 
where shoulder seam meets 
collar seam. 
 
Find center of armholes, from 
armpit to shoulder, and draw 
line straight across. 
 
As an alternative, you can 
draw a horizontal line at the 
If you’re only putting 
embroidery on one side, then 
the name and/or logo should 
go on the left chest position.  
If you’re putting the person’s 
name and logo on two sides, 
the name should go on the 
right and the logo should go 
on the left.  Rational:  When 
you shake hands, your eye 
level of the second button or 
snap. 
 
Center of design should go 
where lines intersect. 
naturally falls so the other 
person’s right shoulder/chest 
area, so that’s the side where 
their name should be. 
Jacket Back  Center design from left to 
right. 
 
Top of design should be 2‐3 
inches below bottom of collar, 
or 4‐5 inches down from base 
of neck. 
 
Design should be placed lower 
on jackets with hoods, or for 
wearers with long hair. 
Center of design should be 6‐
8 inches below bottom of 
collar, typically centered 
between shoulder blades.  
Okay for design to go below 
armpits. 
Robes  Draw lines straight down from 
where shoulder seam meets 
collar seam. 
 
Find center of armpits, from 
armpit to shoulder, and draw 
line straight across. 
 
As an alternative, you can 
draw a horizontal line at the 
level of the second button or 
snap. 
 
Center of design should go 
where lines intersect. 
 
 
Embroidery Placement Chart for Miscellaneous Clothes 
Item  Placement  Other Considerations 
Shorts Leg  Mark the center front of the 
leg.  Mark the point that’s 
halfway between your first 
mark and the side seam.  That 
second mark should be the 
center of your design.  The 
bottom of the design should 
be ¼ to ½ inch above the hem 
stitching on the lower edge of 
 
the shorts. 
Pants Leg  The design should be on the 
left leg at the crotch level, and 
centered between the side 
seam and the inseam. 
 
Alternately, the right edge of 
the design can be 2 inches 
from the side seam, at the 
crotch lever. 
 
Capri Pants  Encircle cuff or go partway up 
the outside seam. 
Usually only done on one leg. 
But may be done on both legs 
if desired.  Use the same 
design on a coordinating shirt.
Pajamas  Draw line straight down from 
where shoulder seam meets 
collar seam. 
 
Find center of armholes, from 
armpit to shoulder, and draw 
line straight across.  If you 
place this line too low, the 
design may go across a 
woman’s breast area. 
 
As an alternative, you can 
draw a horizontal line at the 
level of the second button or 
snap. 
 
On a V‐neck shirt, you can 
draw a horizontal line even 
with the bottom of the V. 
 
Center of design should go 
where the lines intersect. 
 
Skirts  Place designs along the 
hemline, with bottom of the 
design ½ to 1 inch above the 
hemmed edge. 
Print out designs before 
embroidering, and place them 
around the skirt to figure out 
equal distances between 
designs.  Use a similar 
distance between bottom of 
design and edge of fabric, to 
make placement appear nore 
logical.  If distance between 
design is greater than 3‐4 
inches, then it won’t look very 
good to have the designs that 
far above the edge of the 
hem, so forget this idea, and 
just put them ½ to 1 inch 
above hemline. 
 
Embroidery Placement for Clothing Accessories 
Item  Placement  Special Considerations 
Aprons  Center of the bib, 4 inches 
down from the top edge. 
 
Bibs  Centered on the bib.   May 
also place design centered 
from left to right, but closer to 
the lower edge of the bib. 
 
Hair Ribbon  Near the end of the ribbon.  Hoop tearaway hydrostick 
backing, and stick ribbons 
down onto it. 
Handkerchiefs  1 ½ inches from corner point, 
sewn at a 45 degree angle. 
Monogram should face the 
point, not the center of the 
handkerchief. 
Hats  Place anywhere on back, 
front, or sides. 
 
Gloves  Hold the gloves so the wrist is 
on top, and the fingers are on 
the bottom, with the palm 
facing down.  In this position, 
the top of the monogram 
should be next to the top 
edge, just below the wrist 
edge, about ¼ to ½ inch.  The 
design should be ¼ to ½ inch 
away from the outside seam 
which is next to the pinky 
finger. 
 
Mufflers and long rectangular 
scarves. 
Place design centered at one 
end of muffler of scarf, above 
the hen on short edge.  The 
distance from the edge should 
be equal to 1/4th
 of the width 
of the scarf.  For example, if 
 
the scarf is 4 inches wide, 
then the bottom of the design 
should be 1 inch above the 
edge. 
Square Scarves and Bandanas  Place in corner of square 
scarf, 1‐2 inches about point. 
Do not put on point that has 
tag or label. 
Shoe Laces  New the ends of the shoe 
laces 
Hoop tearaway hydrostick, 
and place shoe laces onto it. 
Socks  Design should be centered on 
the top half of cuff, right side 
up after cuff is folded down, 
on the outside of the leg.   
Design should be ¼ to 1 inch 
tall. 
Stethoscope Covers  Design should be centered 
between ends of tube styled 
cover, or on the lower portion 
of Y shaped cover. 
 
Name can be placed on upper 
arms of Y shaped cover. 
Design of monogram may be 
placed either horizontal or 
vertical. 
Ties  Design should be centered 2” 
to 2 ½” up from the bottom 
point, and centered on the 
front of the tie. 
 
If worn with a vest, the design 
should be centered 9 to 11 
inches above the bottom 
point. 
Monogram should be ¼ to ½ 
inches tall. 
 
Embroidery Placement for Religious Items
Item  Placement  Other Considerations 
Robe Collars  Centered on collar, halfway 
between the neck edge and 
the point in the center, or the 
lower straight edge. 
May also be placed on the left 
collar halfway between the 
center and the left edge. 
Designs are usually 2‐4 inches 
tall. 
Robe Fronts  The center front portion of 
the robe has a velvet facing 
which may be decorated, with 
matching designs directly 
across from each other, at the 
Designs are usually 3‐5 inches 
tall. 
mid‐chest level. 
Robe Scarves  Placed either on left side of 
scarf only, or with matching 
designs on both sides of scarf, 
directly across from each 
other.  Designs or lettering 
are usually at upper to mid 
chest level, but may also be 
placed near ends of scarf.  
Scarf designs usually run 
vertically, including 
monograms.  Designs and 
letters are usually 3‐5 inches 
tall. 
Robe Tunics 
(Goes over robe and is floor 
length) 
Centered over front chest 
area. 
Designs are usually 4‐7 inches 
tall. 
Bible Bookmarks for large 
pulpit Bibles. 
Place cross or other design 
centered at one end of the 
bookmark, facing the point at 
the end 
Size of design should be 1/4th
 
to 1/3rd
 the width of the scarf.
Pulpit Covers  Place cross or other design 
centered above the point, on 
the part that hangs over the 
front side of the pulpit. 
Size of design should be 1/4th
 
to 1/3rd
 the width of the 
cover. 
 
Embroidery Placement Chart for Miscellaneous Items 
Item  Placement  Other Considerations 
Bath Sheets 
Beach Towels 
Bottom of monogram should 
be 5 inches above hen or 2‐3 
inches above border.  Place 
on opposite end from the 
label. 
Monogram should be 5 inches 
tall. 
Bath Towels  Bottom of monogram should 
be 4 inches above hen or 1‐2 
inches above border.  Place 
on opposite end from the 
label. 
Monogram should be 4 inches 
tall. 
Hand Towels  Bottom of monogram should 
be 2 inches above the hen or 
1 to 1 ½ inches above border.  
Place on opposite end from 
the label. 
Monogram should be 3 inches 
tall. 
 
Fingertip Towels  Bottom of monogram should 
be 1 ½ inch to 2 inches above 
hen or 1 to 1 ½ inches above 
border.  Place on opposite 
end from the label. 
Monogram should be 2 inches 
tall. 
Golf Towel  Centered near top edge of 
towel, below the grommet. 
Bottom of towel should be 
free of embroidery, for wiping 
hands on. 
Wash Cloths  Bottom of monogram should 
be 1 ½ inches above hen or 1 
inch above border.  Place on 
opposite end from the label. 
 
If there is no border, 
monogram may be placed in 
corner at a 45 degree angle. 
Monogram should be 1 ½ 
inches tall. 
Sports Towels  6 inches above hem, or 3‐4 
inches above border. 
Monogram should be 3‐6 
inches tall. 
Bath Wraps  Equal distances, of 1‐2 inches 
from front opening. 
Design may also go down the 
front edge. 
Sheets  With wide hem at the bottom  
(so sheet is upside down), the 
design should be right side up,  
The bottom of the monogram 
should be 2 inches above the 
wide hem, and centered from 
left to right.  Embroider on 
the right side of the fabric. 
When you make the bed,  the 
top sheet should be placed 
wrong side up, then the top 
(wide) edge should be folded 
back over the top edge of the 
blanket, revealing the 
monogram, which is now right 
side up. 
 
Do not embroider fitted 
bottom sheet. 
Pillowcases  The monogram should be 
stitched on the wide hem of 
the open edge of the 
pillowcase, facing the open 
edge.  It should be centered 
from left to right and also 
centered halfway between 
the edge of the pillowcase 
and the hem stitching. 
 
Pillow Sham  Center the design on the 
middle of the pillow sham, 
facing the long edge of the 
sham 
 
Blankets  9‐11 inches down from the 
point of the corner, at a 45 
degree angle. 
The design should be facing 
the point, not facing the main 
part of the blanket. 
Napkins  3 inches from point of corner.  Place opposite of label or tag. 
Placemats  Top right corner, 3 inches 
diagonally from point of 
corner. 
 
Table Scarves  Place matching design at each 
end, facing the short ends. 
Coordinating designs may go 
in the center, but should 
either be non‐directional, or 
placed in pairs, facing either 
left and right, or up and 
down. 
Table Cloths  5 inches from the corner 
points. 
 
Window Valances  Large designs should be 
centered between bottom 
edge of valance and bottom 
of rod pocket. 
 
Small designs should be 
placed ½  to 1 inch above 
bottom edge of valance. 
 
Director’s Chairs  Centered on back of chair.  Letters should be 4‐6 inches 
tall, but a minimum of 2 
inches tall, so people can read 
it across a room. 
Christmas Stockins  Centered on the cuff of the 
stocking. 
 
Christmas Tree Skirts  Centered on the front of the 
skirt. 
 
Bags, Totes, and Purses  Usual placement is 4 inches 
below top edge, centered 
between straps. 
Placement anywhere is 
acceptable. 
Horse Blankets  Side Center (multiple layers) 
 
Hip 
 
Shoulder 
 
Lower Corner below hip. 
Straight of at angle if on 
bottom corners. 
Chart prepared by Diamond Threadworks 
 

More Related Content

Similar to 00163201012270434338216

NECKLINE FINISHES
NECKLINE FINISHESNECKLINE FINISHES
NECKLINE FINISHESTsekpoPeace
 
Bdft ii, d&pm, unit-i, draping
Bdft ii, d&pm, unit-i, drapingBdft ii, d&pm, unit-i, draping
Bdft ii, d&pm, unit-i, drapingRai University
 
Understanding the guide sheet and symbols ppt
Understanding the guide sheet and  symbols pptUnderstanding the guide sheet and  symbols ppt
Understanding the guide sheet and symbols pptsrsuganthifbs
 
Making perfect pants
Making perfect pantsMaking perfect pants
Making perfect pantsRiding Mani
 
Parts and Assembly of a Shirt
Parts and Assembly of a ShirtParts and Assembly of a Shirt
Parts and Assembly of a ShirtIntrocanvas
 
fullness in garment ( tuck dart pleats etc)
fullness in garment ( tuck dart pleats etc)fullness in garment ( tuck dart pleats etc)
fullness in garment ( tuck dart pleats etc)Ragu Nathan
 
SEAMS AND THEIR TYPES
SEAMS AND THEIR TYPESSEAMS AND THEIR TYPES
SEAMS AND THEIR TYPESSabeema
 
tie dyeing
 tie dyeing tie dyeing
tie dyeingahad003
 
Setting up your tshirt printing project
Setting up your tshirt printing projectSetting up your tshirt printing project
Setting up your tshirt printing projectTshirts Canada
 
Mighty Girl Clothing
Mighty Girl ClothingMighty Girl Clothing
Mighty Girl Clothingcrosland_a
 
Three dimensional dress form
Three dimensional dress formThree dimensional dress form
Three dimensional dress formAdithy_Kottangal
 
Construction of your bag
Construction of your bagConstruction of your bag
Construction of your bagcarnly
 
Fashion Design student work (Dezyne E' cole College)
Fashion Design student work (Dezyne E' cole College)Fashion Design student work (Dezyne E' cole College)
Fashion Design student work (Dezyne E' cole College)dezyneecole
 
Childrens body measurement
Childrens body measurementChildrens body measurement
Childrens body measurementEzekiel Vic Eboy
 
Periodic Table of T Shirts Instructions
Periodic Table of T Shirts InstructionsPeriodic Table of T Shirts Instructions
Periodic Table of T Shirts InstructionsSimon Norris
 

Similar to 00163201012270434338216 (20)

NECKLINE FINISHES
NECKLINE FINISHESNECKLINE FINISHES
NECKLINE FINISHES
 
Bdft ii, d&pm, unit-i, draping
Bdft ii, d&pm, unit-i, drapingBdft ii, d&pm, unit-i, draping
Bdft ii, d&pm, unit-i, draping
 
Understanding the guide sheet and symbols ppt
Understanding the guide sheet and  symbols pptUnderstanding the guide sheet and  symbols ppt
Understanding the guide sheet and symbols ppt
 
Making perfect pants
Making perfect pantsMaking perfect pants
Making perfect pants
 
Parts and Assembly of a Shirt
Parts and Assembly of a ShirtParts and Assembly of a Shirt
Parts and Assembly of a Shirt
 
Shirt stitching
Shirt stitchingShirt stitching
Shirt stitching
 
Draping
DrapingDraping
Draping
 
fullness in garment ( tuck dart pleats etc)
fullness in garment ( tuck dart pleats etc)fullness in garment ( tuck dart pleats etc)
fullness in garment ( tuck dart pleats etc)
 
SEAMS AND THEIR TYPES
SEAMS AND THEIR TYPESSEAMS AND THEIR TYPES
SEAMS AND THEIR TYPES
 
tie dyeing
 tie dyeing tie dyeing
tie dyeing
 
Setting up your tshirt printing project
Setting up your tshirt printing projectSetting up your tshirt printing project
Setting up your tshirt printing project
 
Mighty Girl Clothing
Mighty Girl ClothingMighty Girl Clothing
Mighty Girl Clothing
 
fashion
fashionfashion
fashion
 
Three dimensional dress form
Three dimensional dress formThree dimensional dress form
Three dimensional dress form
 
Construction of your bag
Construction of your bagConstruction of your bag
Construction of your bag
 
Fashion Design student work (Dezyne E' cole College)
Fashion Design student work (Dezyne E' cole College)Fashion Design student work (Dezyne E' cole College)
Fashion Design student work (Dezyne E' cole College)
 
Draping 140701002255-phpapp02
Draping 140701002255-phpapp02Draping 140701002255-phpapp02
Draping 140701002255-phpapp02
 
Childrens body measurement
Childrens body measurementChildrens body measurement
Childrens body measurement
 
Periodic Table of T Shirts Instructions
Periodic Table of T Shirts InstructionsPeriodic Table of T Shirts Instructions
Periodic Table of T Shirts Instructions
 
Types of collar
Types of collarTypes of collar
Types of collar
 

Recently uploaded

Unit 1 - Soil Classification and Compaction.pdf
Unit 1 - Soil Classification and Compaction.pdfUnit 1 - Soil Classification and Compaction.pdf
Unit 1 - Soil Classification and Compaction.pdfRagavanV2
 
Thermal Engineering Unit - I & II . ppt
Thermal Engineering  Unit - I & II . pptThermal Engineering  Unit - I & II . ppt
Thermal Engineering Unit - I & II . pptDineshKumar4165
 
UNIT-II FMM-Flow Through Circular Conduits
UNIT-II FMM-Flow Through Circular ConduitsUNIT-II FMM-Flow Through Circular Conduits
UNIT-II FMM-Flow Through Circular Conduitsrknatarajan
 
UNIT-IFLUID PROPERTIES & FLOW CHARACTERISTICS
UNIT-IFLUID PROPERTIES & FLOW CHARACTERISTICSUNIT-IFLUID PROPERTIES & FLOW CHARACTERISTICS
UNIT-IFLUID PROPERTIES & FLOW CHARACTERISTICSrknatarajan
 
The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...
The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...
The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...ranjana rawat
 
KubeKraft presentation @CloudNativeHooghly
KubeKraft presentation @CloudNativeHooghlyKubeKraft presentation @CloudNativeHooghly
KubeKraft presentation @CloudNativeHooghlysanyuktamishra911
 
Top Rated Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...
Top Rated  Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...Top Rated  Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...
Top Rated Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...Call Girls in Nagpur High Profile
 
Glass Ceramics: Processing and Properties
Glass Ceramics: Processing and PropertiesGlass Ceramics: Processing and Properties
Glass Ceramics: Processing and PropertiesPrabhanshu Chaturvedi
 
Call for Papers - Educational Administration: Theory and Practice, E-ISSN: 21...
Call for Papers - Educational Administration: Theory and Practice, E-ISSN: 21...Call for Papers - Educational Administration: Theory and Practice, E-ISSN: 21...
Call for Papers - Educational Administration: Theory and Practice, E-ISSN: 21...Christo Ananth
 
CCS335 _ Neural Networks and Deep Learning Laboratory_Lab Complete Record
CCS335 _ Neural Networks and Deep Learning Laboratory_Lab Complete RecordCCS335 _ Neural Networks and Deep Learning Laboratory_Lab Complete Record
CCS335 _ Neural Networks and Deep Learning Laboratory_Lab Complete RecordAsst.prof M.Gokilavani
 
Online banking management system project.pdf
Online banking management system project.pdfOnline banking management system project.pdf
Online banking management system project.pdfKamal Acharya
 
The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...
The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...
The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...ranjana rawat
 
Vivazz, Mieres Social Housing Design Spain
Vivazz, Mieres Social Housing Design SpainVivazz, Mieres Social Housing Design Spain
Vivazz, Mieres Social Housing Design Spaintimesproduction05
 
data_management_and _data_science_cheat_sheet.pdf
data_management_and _data_science_cheat_sheet.pdfdata_management_and _data_science_cheat_sheet.pdf
data_management_and _data_science_cheat_sheet.pdfJiananWang21
 
Call Girls Walvekar Nagar Call Me 7737669865 Budget Friendly No Advance Booking
Call Girls Walvekar Nagar Call Me 7737669865 Budget Friendly No Advance BookingCall Girls Walvekar Nagar Call Me 7737669865 Budget Friendly No Advance Booking
Call Girls Walvekar Nagar Call Me 7737669865 Budget Friendly No Advance Bookingroncy bisnoi
 
Thermal Engineering-R & A / C - unit - V
Thermal Engineering-R & A / C - unit - VThermal Engineering-R & A / C - unit - V
Thermal Engineering-R & A / C - unit - VDineshKumar4165
 
VIP Model Call Girls Kothrud ( Pune ) Call ON 8005736733 Starting From 5K to ...
VIP Model Call Girls Kothrud ( Pune ) Call ON 8005736733 Starting From 5K to ...VIP Model Call Girls Kothrud ( Pune ) Call ON 8005736733 Starting From 5K to ...
VIP Model Call Girls Kothrud ( Pune ) Call ON 8005736733 Starting From 5K to ...SUHANI PANDEY
 
Extrusion Processes and Their Limitations
Extrusion Processes and Their LimitationsExtrusion Processes and Their Limitations
Extrusion Processes and Their Limitations120cr0395
 

Recently uploaded (20)

Unit 1 - Soil Classification and Compaction.pdf
Unit 1 - Soil Classification and Compaction.pdfUnit 1 - Soil Classification and Compaction.pdf
Unit 1 - Soil Classification and Compaction.pdf
 
Thermal Engineering Unit - I & II . ppt
Thermal Engineering  Unit - I & II . pptThermal Engineering  Unit - I & II . ppt
Thermal Engineering Unit - I & II . ppt
 
UNIT-II FMM-Flow Through Circular Conduits
UNIT-II FMM-Flow Through Circular ConduitsUNIT-II FMM-Flow Through Circular Conduits
UNIT-II FMM-Flow Through Circular Conduits
 
UNIT-IFLUID PROPERTIES & FLOW CHARACTERISTICS
UNIT-IFLUID PROPERTIES & FLOW CHARACTERISTICSUNIT-IFLUID PROPERTIES & FLOW CHARACTERISTICS
UNIT-IFLUID PROPERTIES & FLOW CHARACTERISTICS
 
The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...
The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...
The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...
 
KubeKraft presentation @CloudNativeHooghly
KubeKraft presentation @CloudNativeHooghlyKubeKraft presentation @CloudNativeHooghly
KubeKraft presentation @CloudNativeHooghly
 
Top Rated Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...
Top Rated  Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...Top Rated  Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...
Top Rated Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...
 
Glass Ceramics: Processing and Properties
Glass Ceramics: Processing and PropertiesGlass Ceramics: Processing and Properties
Glass Ceramics: Processing and Properties
 
NFPA 5000 2024 standard .
NFPA 5000 2024 standard                                  .NFPA 5000 2024 standard                                  .
NFPA 5000 2024 standard .
 
Call for Papers - Educational Administration: Theory and Practice, E-ISSN: 21...
Call for Papers - Educational Administration: Theory and Practice, E-ISSN: 21...Call for Papers - Educational Administration: Theory and Practice, E-ISSN: 21...
Call for Papers - Educational Administration: Theory and Practice, E-ISSN: 21...
 
Call Now ≽ 9953056974 ≼🔝 Call Girls In New Ashok Nagar ≼🔝 Delhi door step de...
Call Now ≽ 9953056974 ≼🔝 Call Girls In New Ashok Nagar  ≼🔝 Delhi door step de...Call Now ≽ 9953056974 ≼🔝 Call Girls In New Ashok Nagar  ≼🔝 Delhi door step de...
Call Now ≽ 9953056974 ≼🔝 Call Girls In New Ashok Nagar ≼🔝 Delhi door step de...
 
CCS335 _ Neural Networks and Deep Learning Laboratory_Lab Complete Record
CCS335 _ Neural Networks and Deep Learning Laboratory_Lab Complete RecordCCS335 _ Neural Networks and Deep Learning Laboratory_Lab Complete Record
CCS335 _ Neural Networks and Deep Learning Laboratory_Lab Complete Record
 
Online banking management system project.pdf
Online banking management system project.pdfOnline banking management system project.pdf
Online banking management system project.pdf
 
The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...
The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...
The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...
 
Vivazz, Mieres Social Housing Design Spain
Vivazz, Mieres Social Housing Design SpainVivazz, Mieres Social Housing Design Spain
Vivazz, Mieres Social Housing Design Spain
 
data_management_and _data_science_cheat_sheet.pdf
data_management_and _data_science_cheat_sheet.pdfdata_management_and _data_science_cheat_sheet.pdf
data_management_and _data_science_cheat_sheet.pdf
 
Call Girls Walvekar Nagar Call Me 7737669865 Budget Friendly No Advance Booking
Call Girls Walvekar Nagar Call Me 7737669865 Budget Friendly No Advance BookingCall Girls Walvekar Nagar Call Me 7737669865 Budget Friendly No Advance Booking
Call Girls Walvekar Nagar Call Me 7737669865 Budget Friendly No Advance Booking
 
Thermal Engineering-R & A / C - unit - V
Thermal Engineering-R & A / C - unit - VThermal Engineering-R & A / C - unit - V
Thermal Engineering-R & A / C - unit - V
 
VIP Model Call Girls Kothrud ( Pune ) Call ON 8005736733 Starting From 5K to ...
VIP Model Call Girls Kothrud ( Pune ) Call ON 8005736733 Starting From 5K to ...VIP Model Call Girls Kothrud ( Pune ) Call ON 8005736733 Starting From 5K to ...
VIP Model Call Girls Kothrud ( Pune ) Call ON 8005736733 Starting From 5K to ...
 
Extrusion Processes and Their Limitations
Extrusion Processes and Their LimitationsExtrusion Processes and Their Limitations
Extrusion Processes and Their Limitations
 

00163201012270434338216