1. The Waterproofing System Specialist
HESHENG®
HS-16(K11)
Two Component General Polymer Modified Compound Waterproofing
Coating
INTRODUCTION
HS-16 K11 Two Component General Polymer Modified Compound Waterproofing Coating is according to
company's proprietary technology, using the penetration mechanism of crystalline materials on the permeability of
concrete, combined with the polymer emulsion and concrete and cement mortar base special adhesive, water retention,
and certain flexibility, with wool stoma of concrete permeable crystallization, as well as the base to form a whole
consistent with dual compound waterproof material waterproof function of integration.
ADVANCE
1. The coating has the inhibit the growth of mold, can prevent humidity to act the role of the salt pollution;
2. Pulp can be directly after dry solid stickup ceramic tile or plaster leveling;
3. The construction in complex rough surface;
4. Can be in damp base surface construction;
5. Can cover small crack, resist the slight shock;
6. Nonpoisonous and harmless, can be directly used for drinking, pools and fish pond.
APPLICATION RANGE
Apply to the following moistureproof waterproof engineering:
1. Indoor and outdoor cement concrete structure, the cement brick wall, brick wall, light structure;
2. The floor wall floor, kitchen, bathroom, planter, ground, garage;
3. The consumption of pool, swimming pool, fish pond, sewage treatment ponds;
4. Apply brick stone material, ceramic tile, land before the board, wall paper, gypsum board on the substrate of a front
end processing.
MAIN TECHNICAL INDEX
Executive Standard: JC/T 984-2011 Type II
Test Item Index
Setting Time
Initial Setting min ≥45
Final Setting h ≤24
Resistance to
Permeable Pressure Mpa
Coat(Layer) Test-piece 7d ≥0.5
Tension & Pressure Strength Mpa ≥24.0
Tension & Fold Strength Mpa ≥8.0
Flexibility (Lateral deformability) mm ≥1.0
Bonding Strength Mpa
7d ≥1.0
28d ≥1.2
1.Setting time can be adjusted according to user needs and seasonal change.
When the thickness of the products use is not more than 5 mm measured coating specimen permeability pressure;

2. When the thickness of the products use greater than 5 mm mortar
2. specimen permeability pressure. Can choose according to the purpose, determination of coating or seepage
pressure resistance of mortar specimens
CONSTRUCTION TECHNOLOGY
1. The base surface treatment: base must be strong, clean, smooth, moist, without oil and floating ash; The base
surface with pores, cracks and other defects, repaired with cement mortar screeding in advance; inside and outside
Angle with a spatula and to make up half the rounded;
2.Stirring and mixing: mixing by mixing ratio add additive into the container, then slowly add powder into the
additives, at the same time fully stir until do not contain particles, uniform glue paste can be used; In use process
should keep intermittent mixing, in case of layered deposits. Mixing ratio: liquid (additive) : powder = 1:2. 77
(weight ratio);
3. Construction: directly with brush or roller coating on the base, using uniform, do not leak brush; If used in damp,
need to besmear to brush a layer; Used for waterproof, need to besmear to brush two to three layers. When the first
layer of dry solid to just not glue the hand (generally 1-2 hours), can besmear to brush the second layer, every two
layer brushing direction should be perpendicular to the intersection;
4. Coating protection: pulp after the completion of construction, not completely dry before solid coating for the
necessary protection, including a ban on pedestrians, rain erosion, exposure, sharp object injury, etc.; After
completely dry solid coating does not need to do special protective layer;
5. Curing coating: coating 24 hours after the completion of the engineering proposal with wet cloth cover coating or
spray water to curing coating, general 2-3 days; Air humidity is big, poorly ventilated place dry solid time will be
longer, and the shorter, the air circulation, particularly poor environment, for the progress of the mechanical
ventilation method can be used to speed up the dry solid;
6. Construction temperature: is suitable in 5 ℃ and 40 ℃ under the environment of the construction.
DOSAGE OF REFERENCE
Waterproof for no hydrostatic pressure, flow rate of membrane thickness of about 1 mm, 1.5-2.0 kg / ㎡
Used for important waterproof, coating thickness of about 2 mm, 2.5-4.0 kg / ㎡
MATTERS ATTENTION
Limit the use in the following circumstances:
1. The building vibration, displacement, contraction larger part;
2. The structure of the expansion joints, deformation cracks, settlement joint, the post-pouring belt, wall
tube sealing, etc.
PACKAGE AND STORAGE
20kg/Pail
Stored in dry place, not unsealed product, shelf life 12 months
SAFETY MATTERS
This product is alkaline, should avoid contact with the skin for a long time to avoid a large number of
inhalation of dust and pay attention to protect the eyes, the eyes, rinse with clear water and go to a
doctor as soon as possible.
This product non-toxic harmless, belong to environmental protection product.
Foshan Shunde Hesheng Chemical Industry Co., Ltd.
Web: www.he-sheng.com.cn/en/ E-mail:kevin@he-sheng.com.cn
Sales Manager: Kevin Cell/WhatsApp: +86 13794633232 Tel.:+86 757 22904888 Fax.:+86 757 22904999
Headquarter Addr.:No.11-1-2, Fu An Industrial Area, Leliu, Shunde, Foshan City, Guangdong Province, China
Sub-factory Addr.:NO.10 Fuyuan Rd.,Rongbian, Rongui, Shunde, Foshan City, Guangdong Province, China