Indicaciones de como hacerlo uno mismo.

1. Publications No.
Issue Date
INSTALLATION
INSTRUCTIONS
Accessory Application
© 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 44392 (1008) 1 of 1208V31-SNA-1D00-91
AII 44392
FOG LIGHTS
P/N 08V31-SNA-100D
2011 CIVIC
4-DOOR
AUG 2010
PARTS LIST
Right fog light
Left fog light
Switch harness
Fog light harness
Subharness
Combination light switch
6 Wire ties
Clip
2 Self-tapping screws
20A Fuse
(Some may not be used.)
Relay
Ground bolt
2 Spring nuts
www.collegehillshonda.com

2. 2 of 12 AII 44392 (1008) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Ratchet
10 mm and 12 mm Sockets
Blanket
Diagonal cutters
5 mm Hex wrench
Illustration of the Fog Lights Installed on the Vehicle
851210AK
SUB
HARNESS
COMBINATION
LIGHT SWITCH
SWITCH
HARNESS
RELAY
LEFT FOG LIGHT
FOG LIGHT
HARNESS
RIGHT
FOG
LIGHT
20A FUSE
INSTALLATION
1. Make sure you have the anti-theft codes for the
audio system and navigation system (if equipped),
then write down the radio presets.
2. Disconnect the negative cable from the battery.
3. Remove the front bulkhead cover (two expansion
clips, three clips, and move the right and left fender
trims inward).
Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
5202062T
EXPANSION
CLIPS
3 CLIPS
(Pull Straight up.)
PANEL
RIGHT
FENDER
TRIM
FRONT
BULKHEAD
COVER
LEFT
FENDER
TRIM
www.collegehillshonda.com

3. © 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 44392 (1008) 3 of 12
4. With the help of an assistant, remove the front
bumper (four long clips, four center clips, two socket
bolts, and two self-tapping screws). To prevent
damage, set the front bumper on a blanket.
5. Remove the left fog light cover (four tabs).
850904AK
2 SELF-
TAPPING
SCREWS
LONG
CLIPS
CENTER
CLIPS
LONG
CLIPS
SOCKET
BOLTS
FRONT
BUMPER
840301AK
LEFT FOG LIGHT COVER
4 TABS
FRONT BUMPER
6. Install a spring nut onto the front bumper.
7. Install the left fog light into the fog light cover
opening, and secure it with a self-tapping screw.
8. Repeat steps 5 through 7 on the other side.
9. Route the fog light harness 2-pin connector between
the lower grille and the front bumper from the right
side to the left side.
850801AK
SELF-
TAPPING
SCREW
FRONT
BUMPER
FRONT BUMPER
SPRING
NUT
FOG LIGHT
COVER
OPENING
LEFT FOG LIGHT
850802AK
FRONT BUMPER
FOG LIGHT HARNESS
2-PIN CONNECTOR
FOG LIGHT
HARNESS
2-PIN/4-PIN
CONNECTORS
FRONT
BUMPER
FOG LIGHT
HARNESS
LOWER GRILLE
www.collegehillshonda.com

4. 4 of 12 AII 44392 (1008) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
10. Attach the clip on the fog light harness to each hole
in the lower grille.
11. Secure the fog light harness to the lower grille with
one wire tie.
12. Plug the fog light harness 2-pin connector into the
left fog light bulb.
850901AK
FOG LIGHT
HARNESS
LOWER
GRILLE
FOG LIGHT HARNESS CLIPS
(Attach them to the hole in the lower grille.)
WIRE TIE
LOWER GRILLE
FOG LIGHT HARNESS
850902AK
FOG LIGHT HARNESS
2-PIN CONNECTOR
LEFT FOG LIGHT
BULB
13. Plug the fog light harness 2-pin connector into the
right fog light bulb.
14. Install the fog light harness clip onto the lower
grille rib.
15. Remove three bolts from the washer reservoir tank.
850903AK
LOWER
GRILLE RIB
FOG LIGHT
HARNESS
2-PIN
CONNECTOR
RIGHT
FOG LIGHT
BULB
FOG LIGHT
HARNESS
CLIP
852101AK
3 BOLTS
WASHER RESERVOIR
TANK
www.collegehillshonda.com

5. © 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 44392 (1008) 5 of 12
16. Locate the 1-pin connector blue-taped to the vehicle
harness and remove the blue tape to free the 1-pin
connector. Plug the vehicle 1-pin connector you just
freed into the subharness 1-pin connector.
860601AK
VEHICLE
HARNESS
BLUE
TAPE
(Remove.)
SUBHARNESS
1-PIN CONNECTOR
SUBHARNESSVEHICLE 1-PIN
CONNECTOR
17. Route the subharness between the washer reservoir
tank and vehicle panel as shown.
18. Secure the subharness ground terminal to the
vehicle frame using the ground bolt supplied.
19. Reinstall the washer reservoir tank. Check that the
pipe is installed securely.
852910BK
SUBHARNESS
VEHICLE
FRAME
VEHICLE
PANEL
WASHER
RESERVOIR
TANK
SUB-
HARNESS
GROUND
TERMINAL
GROUND
BOLT
PIPE
www.collegehillshonda.com

6. 6 of 12 AII 44392 (1008) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
20. Secure the subharness clip to the vehicle frame, and
secure the subharness to the vehicle harness using
two wire ties.
21. Slide the clip onto the subharness 4-pin connector,
and secure it to the vehicle frame.
22. Plug the fog light harness 4-pin connector to the sub-
harness 4-pin connector, then reinstall the front
bumper.
860602BK
VEHICLE FRAME
SUB-
HARNESS
WIRE TIES
SUBHARNESS
4-PIN CONNECTOR
SUB-
HARNESS
CLIP
CLIP
851201AK
FOG LIGHT HARNESS
4-PIN CONNECTOR
SUBHARNESS
4-PIN CONNECTOR
FRONT BUMPER
23. If equipped, remove the driver’s dashboard under
cover by turning the knob counterclockwise, and
releasing two clips and pin. Take care not to damage
the clips.
24. Remove the driver’s dashboard lower cover
(eight clips). Take care not to damage the clips.
5202112T
PIN
2 CLIPS
KNOB
DRIVER’S
DASHBOARD
UNDER COVER
5202121T
8 CLIPS
DRIVER’S
DASHBOARD
LOWER COVER
www.collegehillshonda.com

7. © 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 44392 (1008) 7 of 12
25. Lower the tilt lever, and pull the steering wheel
toward you. Insert a flat-tip screwdriver along the
guide of the column lower cover, and pry the
retaining tab of the column upper cover.
26. Push on the column lower cover in the area shown
to separate the column upper cover from the column
lower cover (three retaining tabs). Pull up to remove
the column upper cover (two hooks).
5308521T
RETAINING
TAB
FLAT-TIP
SCREWDRIVER
STEERING WHEEL
(Pull toward you.)
2 RETAINING TABSCOLUMN
UPPER
COVER
TILT LEVER
GUIDE
COLUMN
LOWER
COVER
Push.
HOOKS
RETAINING
TAB
27. Remove the column lower cover (two self-tapping
screws and one screw).
28. Push the retaining tab on the vehicle white 34-pin
connector, raise the lock lever, and remove the
connector from the fuse box. Close the lock lever on
the vehicle white 34-pin connector and remove the
cover by sliding it off the connector.
5308530T
COLUMN
LOWER
COVER
SELF-TAPPING
SCREWSSCREW
851202AK
Push.
VEHICLE
WHITE 34-PIN
CONNECTOR
WHITE 34-PIN
CONNECTOR
Push. Slide.
Push.
RETAINING
TAB
COVERFUSE
BOX
LOCK
LEVER
www.collegehillshonda.com

8. 8 of 12 AII 44392 (1008) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
29. Insert the switch harness white/red terminal and blue
terminal into the vehicle white 34-pin connector.
30. Reinstall the vehicle white 34-pin connector.
31. Route the switch harness above the vehicle knee
bolster.
5307170T
SWITCH
HARNESS
TERMINALS
WHITE/RED TERMINAL
BLUE
TERMINAL
VEHICLE WHITE
34-PIN CONNECTOR
LOCK LEVER
SWITCH
HARNESS
Harness Side View
5307180T
VEHICLE KNEE
BOLSTER
SWITCH
HARNESS
32. Plug the relay into the switch harness relay block,
then slide the relay block onto the vehicle bracket
stay.
33. Locate the 1-pin connector blue-taped to the vehicle
harness. Plug the switch harness 1-pin connector
into the vehicle 1-pin connector.
5307192T
SWITCH
HARNESS
RELAY
BLOCK
VEHICLE
BRACKET
STAY
RELAY
SWITCH
HARNESS
5307202T
SWITCH
HARNESS
VEHICLE 1-PIN
CONNECTOR
SWITCH HARNESS
1-PIN CONNECTOR
www.collegehillshonda.com

9. © 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 44392 (1008) 9 of 12
34. Secure the switch harness to the vehicle harness
and vehicle knee bolster with three wire ties in the
areas shown.
35. Lower the tilt lever and pull the steering wheel
toward you.
36. Turn the steering wheel 90° counterclockwise.
37. Unplug the vehicle 12-pin connector from the
combination light switch. Remove the two screws
from the combination light switch. While pushing the
retaining tab, slide the combination light switch out,
and remove it from the steering column. Do not pull
on the lever when removing the switch. Do not
damage the tab hole in the steering column.
5307212T
SWITCH
HARNESS
WIRE
TIE
WIRE
TIES VEHICLE
HARNESS
VEHICLE KNEE
BOLSTER
851203AK
STEERING
COLUMN
SCREWS
STEERING
WHEEL
RETAINING
TAB
COMBINATION
LIGHT SWITCH
VEHICLE 12-PIN
CONNECTOR
CASE
LEVER
TAB
HOLE
COMBINATION
LIGHT SWITCH
38. Install the new combination light switch in the
steering column using the two screws. Hold the case
in your hand, then install the new combination light
switch into the steering column. Push on the case
and securely set the retaining tab into the tab hole.
Do not push on the lever when installing the case.
39. Plug the vehicle 12-pin connector into the new
switch. Replace the vehicle harness.
851204AK
STEERING
COLUMN
VEHICLE 12-PIN
CONNECTOR
COMBINATION
LIGHT SWITCH
SCREWS
(Reuse.)
RETAINING
TAB
CASE
TAB
HOLE
COMBINATION
LIGHT SWITCH
LEVER
www.collegehillshonda.com

10. 10 of 12 AII 44392 (1008) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
40. Install the 20A fuse into the fuse box in the location
shown. If the fuse is already installed, it is not
necessary to install the 20A fuse.
41. Check that all wire harnesses are routed properly
and all connectors are plugged in.
42. Reinstall all removed parts.
43. Connect the negative cable to the battery and
check the operation of all lights and other electrical
accessories.
44. Enter the anti-theft codes for the audio system and
the navigation system (if equipped), and reset the
radio station presets.
45. Reset the clock on vehicles without navigation.
46. If the IMA battery level gauge (BAT) displays zero
segments, start the engine, and hold it between
3,500 and 4,000 rpm (in Park or Neutral) until the
gauge displays at least three segments.
5307240T
FUSE LOCATION “6”
20A FUSE
FUSE BOX
FUSE BOX
USE AND CARE
How to Operate Fog Lights
• Turn the light switch to the “ ” position (headlights on
low beam).
• Turn the fog light switch (indicator is on).
NOTE: The fog light lenses can cloud when the outside
temperature is cold; this is normal and should go away in
warm weather.
Adjusting the Aim
1. Adjust the vertical aim according to local laws and
regulations. To adjust, turn the adjusting screw in or
out until the correct aim is obtained.
2. Repeat on the other side.
871716BK
FOGLIGHT
SWITCH
OFF
Low High
-
-
-
-
- -
-
OFF
HEADLIGHT SWITCH
ONON
851205AK
To lower.
To raise.
ADJUSTING
SCREW
www.collegehillshonda.com

11. © 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 44392 (1008) 11 of 12
BULB REPLACEMENT
1. Remove the self-tapping screw, and pull the fog light
out toward you.
2. Push in the retaining tab, and unplug the connector
from the fog light.
851206AK
SELF-
TAPPING
SCREW FOG LIGHT
851207AK
RETAINING
TAB
(Push.)
CONNECTOR
LEFT FOG LIGHT
3. Remove the bulb from the fog light by turning it
counterclockwise.
851208AK
FOG LIGHT
BULB
www.collegehillshonda.com

12. 12 of 12 AII 44392 (1008) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
4. Install a new bulb in the fog light by turning it
clockwise until it stops.
• Take extreme care when replacing the fog light
bulb to avoid damaging the lenses or finished
surfaces of the body.
• Use only a Honda Genuine halogen light bulb of
specified wattage.
Rating: 12V 55W H11 Halogen Light Bulb
P/N 33165-S5A-003
• Do not touch the bulb. Oily or greasy substances
on the bulb can shorten its service life due to the
heat produced when the bulb is turned on. If the
bulb is accidentally touched, wipe it clean with a
soft cloth that has been dampened with a
denatured alcohol or a mild detergent solution.
• When installing the new bulb, align the cutout on
the fog light with the tab on the new bulb and turn
the new bulb in completely. If not properly
aligned, the fog light may blind oncoming
drivers.
5. Plug the connector to the bulb.
6. Install the fog light in the reverse order of removal.
7. Check that the bulb comes on properly. Adjust the
aim as necessary.
851209AK
CONNECTOR
FOG LIGHT
NEW BULB
Turn the bulb until it stops.
www.collegehillshonda.com