The document summarizes the process used by the KF SSI Togo Team to fabricate coils, capacitors, and twin magrav systems. The main steps are: 1) Coils are fabricated from 1.5mm^2 copper wire with 144 and 81 turns for the inner and outer coils. The coils are nano-coated and processed in a mixture of CH3, CO2, and CUO GANS. 2) Capacitors are made by spraying the GANS mixture onto toilet paper over aluminum foil and rolling copper wire between the layers. 3) Twin magrav systems are constructed using the coils and connecting the capacitors in series to reduce energy usage by 95-96.

1. Presented by:
KF SSI Togo Team
KESHE Family Togo/Keshe
Foundation Togo

2. Presented by: Paul YATOUTE Maguiman
03.11.2016

3. Coil fabrication

4. The copper
The copper is 1.5 mm2

5. Process of puting out
gain

6. Fabrication of coil
We turn the coil on Anti-COIL WAY
144 and 81 turn inner and outer coil

7. Connexion according
to the diagram of KF

8. Nano coated on fire I

9. Mix 3 GANS:
CH3,CO2 and CUO
We mix 3 GANS togheter and put the coil we nano coated with fire
inside.

10. Dry the coil after puting
in the Gans
We dry the Coil after
the processing in the
GANS

11. Hydrogen on coil
1) Put soda costica in the hot water,
2) Put aluminium mesh on the bottom(the one we use is green)
3) Put alluminim on the water of soda costica
4) Put the dry coil with gans on it and cover it for 24h

12. Remark
We remark that when we put the aluminium
in the soda costica,put coil and cover,we
remark that in 24 H,the mixing turn in black
color and the is one gans black in the down of
the bottom

13. Dry the coil after
hydrogen process
We dry again the
coil after hydrogen
process

14. GANS PROCESS
1) We use Sheet metal connected to the nanocoated copper coil
2) We put soda costica in the hot water
3) And put it in the boxe where we connected sheet metal with the coil at the
distance of 12 cm
4) We get blue gans
NB:By inspiration, i use it to spray the coil.
I didn’t wash this gans because there is no compact gans at the down of bottom
Only the color change in the blue.

15. Blue gans use to spray the
coil

16. The coil Ready for
conexion

17. Differente materials

18. Differente materials

19. Capacitor fabrication
1) We take aluminium paper
2) We the toilet paper and put on the aluminium paper
3) We spray the mixing of 3 gans(CH3,CO2 and CUO) on the paper wich is on
aluminium
4) We dry it
NB:I constate there is some things like seed on the the drying process.
You can observe it ton the next picture.

20. Capacitor fabrication

21. Capacitor fabrication
We roll the
copper
nanocaoted
with the
aluminim
Paper where
we have the
drying gans
on the paper.
We turn it on
anticlock
way until it
become
hard.

22. Capacitor coil 45 turns

23. Capacitor fabrication
We roll the coil
on aluminium

24. Capacitor conexion
We connected (-) together and (+) of capacitor toghether and the (-) of capacitor to the
(-) of the stacker and the (+) goes to the (+) of stacker.I use 3 capacitors for one magrav .

25. Remark
We notice that, there is small salt inside because we use one gans
water of CO2 to mixe in the 3 gans mixing where i make with salt

26. The boxes

27. The twins magrav wich
give 95%
We plug the first magrav
extention like you see on
the picture

28. The twins magrav wich
give 95% reduction
We plug
the rest
with the
energy
source and
use the
extention
for the
connection
with the
house

29. The twins magrav with 9
capacitors for 96.5% reduction
Same circuit of
conexion with but we
incresae the
capacitors: 9
capacitor for one
magrav so 18
capacitor for the
twins magravs.

30. The twins magrav with 9
capacitors for 96.5% reduction

31. THANKS