1. CURRICULAM VITAE
Ali Uzair
Q.C INSPECTOR
OBJECTIVE:
Pursue challenging career where I can utilize my intellect technical skill so as to enhance competence of
an organization and myself.
ACADEMIC QUALIFICATION:
Year Degree Earned Board/University Division
·2004 Matriculation (Science) Bahawalpur 1st
·2007 3 year Diploma of Associate Engineer in Electrical P.B.T.E.Lahore 1st
PROFESSIONAL QUALIFICATION:
 ASNT level II ultrasonic testining from NCNDT Islam abad
 level 1 ultrasonic testing (ISO 9712) from NCNDT islam abad
 ASNT NDT LEVEL II in Radiographic Testing
 Certified industrial radiographer from PNRA
COMPUTER SKILLS:
Windows, Microsoft Office, Microsoft Visio, Internet suffering, MMS
COURSES:
 Advance English Language Course, from Leaders English Language Center Sadiq Abad (
Pakistan )
EXPERIENCE:
Having near about 8 years’ experience in Quality Control Department as a QC Inspector Worked with
DATA STEEL PIPE INDUSTRIES (PVT) LTD. as a QC Inspector from 2008 to on date at below NDT Inspection
Stations
 Welding Inspection ( Visual and Final )
 To check welding defects (ICW,BT,High/Low,Pinholes,Undercuts) and
sheet/plate defects (Lamination,Mass Pitting,Scratches,Gouges)
 To check Radial offset of plate edges with dial gauge and welding gauge
 To Determine inside/outside diameter with ring gauges and bar micrometer.
 To Mark different test pieces according to requirements like
GBT,DWT,CVN,PBT,PWT,PBC,CC.
 To Check out of roundness with bar micro meter.
 Thickness check with digital/analogue micro meter, digital ultrasonic
thickness meter, vernier caliper.
 To Check welding bead height with welding gauge.
 To check straightness of pipe with respect to length.
 To check length with reel tape.
 To calculate and verify end and body circumference.

2.  To check lamination with Lux meter to fulfill API requirements.
 To measure bevel angle with bevel protractor.
 To check end squareness.
 3 Layer PE and polypropylene Coating Inspection
 To check and note alla parameters of coating.
 To check due point, humidity and environment temp.
 Check profile of pipe after blasting with press o film and dial indicator.
 Check gel and cure time of applied epoxy.
 Check exit temperature of coated pipes.
 Carried out all tests like peeling resistance test,indentation hardness
test,impact resistance test,cathodic disbondment test,hot water soak test.
 Real Time X-Ray ( Fluoroscopy )
 Calibrate radiographic testing system and set required sensitivity with
required IQI.
 To check weld defects like Slag,Porosity,LOP,LOF,Undercuts,Pipe etc.
 To check after repair pipes and manual welding of pipes.
 Ultrasonic Testing ( Online & Mannual)
 Calibrate unit according to requirements with the help of IIW V1 Block,DIN V2
block,Basic calibration block.
 Magnetic particle inspection
TEST equipment USED:
Familiar and used most inspection equipments including:
 Ultrasonic Thickness meter (Positector Kraut Kramer)
 USK 7D ( Kraut Kramer )
 USPC 2100 ( Kraut Kramer )
 KSE 28 ( Kraut Kramer )
 Vernier Caliper
 Dial Gauge
 Welding Gauge
 Gauss meter
 Bevel Protector
 Dial indicator
 Coating Thickness Meter,
 Portable Holiday Detector
 Online Holiday Detector
 Peeling test machine
 Profile thickness meter
 Mega ohm meter
 Elco meter
 Bar micro meter
 Densitometer
 Survey meter
 Micro meter
RESPONSIBILITIES:
My job is included but not limited to Supervise as a QC Inspector at pipe plant and Coating Plant.
 QC Activities Monitoring & Management.
 All NDT (Non Destructive Test) process
 Preparing routine documentation.
 Interpretation of test results as per API 5L and Data Steel written procedures.
 Preparation of quality reports
 Preparation of PQR / WQR .
 Welding inspection of steel pipes.
 Incoming material inspection i.e. welding wire, electrode, welding flux, hot rolled steel coils,
polyethylene fusion bonded epoxy powder, co – polymer adhesive, chromate etc.
 Monitoring of Coating application
 Bond strength test
 Impact resistance test

3.  Cathodic disbondment test as per international standards and clients requirements
PERSONAL INFORMATION:
Name : Ali uzair
Father’s Name : Abdul sattar
Date of Birth : 24TH July 1988
N.I.C. # : 31301-6012057-5
Marital Status : Married
Postal Address : Chack no 66p p/o sehja tehsil khan pur district rahim yar khan
E-Mail : aliuzair7326@gmail.com
Contact No. : +92-334-7326621
I am a young energetic and dynamic person with experience in steel & coating industry. Strong mechanical/ Quality
management system background. Proven track record in Production, Engineering, andQuality assurance. Practically
use prominent international product & system standards. Extensively use quality tools for analyzing process, product
& system improvement.
Reference: will be furnish upon request