SlideShare a Scribd company logo
1 of 32
Download to read offline
Service Repair Manual
Models
320C LRR Excavator
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GAD
Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564836
Fuel Filter Base - Remove and Install
SMCS - 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/4(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00813127
1. Use Tool (A) to remove fuel filter (3) from fuel filter base (2) .
Note: It is not necessary to remove the fuel filter in order to remove the fuel filter base.
2. Remove banjo bolts (1) and copper washers in order to disconnect the fuel lines (4) from the
fuel filter base (2).
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
Illustration 2 g00813147
3. Remove two bolts (5) and the washers that secure the fuel filter base (2) to the air inlet
manifold. Remove the fuel filter base (2) from the fuel filter bracket.
Installation Procedure
2/4(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00813147
1. Place the fuel filter base (2) in position on the fuel filter bracket. Install the washers and two
bolts (5) that secure the fuel filter base tothe fuel filter bracket.
Illustration 4 g00813127
2. Install the banjo bolts (1) and install new copper washers in order to connect the fuel lines
(4) to the fuel filter base (2) .
3. If the fuel filter was removed, install the fuel filter (3) to the fuel filter base (2). Tighten the
fuel filter by hand according to the instructions that are shown on the fuel filter. Do not
overtighten the fuel filter.
3/4(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GAD
Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565021
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
Start By:
A. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/5(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Illustration 1 g00606301
The 3066 Engine is shown.
1. Remove the bolts (1), the washers, and the clamps (2), which secure the fuel lines to the
inlet manifold (3) .
Illustration 2 g00606310
2. Disconnect the fuel injection lines (4) from the fuel injection nozzles (5) .
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
2/5(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Illustration 3 g00606314
Fuel injection pump for a 3066 Engine
3. Disconnect the end of the fuel injection lines (4) from the fuel injection pump (6) .
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
4. Remove the fuel injection lines (4) from the engine.
Illustration 4 g00606317
5. Loosen the acorn nuts (7), which secure the fuel return line to the fuel injection nozzles.
6. Remove one bolt (8) and the washer from the clamp that secures the fuel return line to the
intake manifold.
Note: The clamp will remain with the fuel return line, when the fuel return line is removed
from the engine.
7. Disconnect fitting (9). Remove fuel return line (10) from the engine.
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
3/5(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 5 g00606317
1. Place the fuel return line (10) in position on the engine. Connect fitting (9) of the fuel return
line to the fuel injection pump.
2. Install the washer and bolt (8) through the clamp in order to secure the fuel return line to the
inlet manifold.
3. Install the fuel return line (10) to the fuel injection nozzles. Secure the fuel return line to the
fuel injection nozzle with acorn nuts (7) .
4/5(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Illustration 6 g00606399
Fuel injection pump for a 3066 Engine
4. Place the fuel injection lines (4) on the engine.
5. Connect the fuel injection lines (4) to the fuel injection pump (6) .
6. Connect the fuel injection lines (4) to the fuel injection nozzles (5) .
Note: The fuel lines (4) should be connected at the fuel injection nozzle (5) and at the fuel
injection pump (6) before tightening the nuts for the fuel injection line.
7. Tighten the nuts for the fuel injection line to a torque of 25 N·m (18 lb ft).
Illustration 7 g00606301
Fuel lines for a 3066 Engine
8. Install the clamps (2), the washers, and the bolts (1), which secure the fuel lines to the inlet
manifold (3) .
End By: Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 26 09:29:25 UTC+0800 2019
5/5(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GAD
Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01151321
Fuel Injection Nozzles - Remove
SMCS - 1254-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B 9U-6278 Adapter 1
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Illustration 1 g00652319
1. Remove bolt (1) and the washer that secures the clamp (2) to the cylinder head assembly.
2. Remove the clamp (2) that secures the fuel injection nozzle (3) in position in the cylinder
head assembly.
Note: Put caps or plugs on all openings immediately in order to prevent contamination in
the fuel system.
Note: Mark the clamp for later installation.
3. Install Tool (B) (not shown) to the fuel injection nozzle.
Note: Tool (B) is installed at the connection (4) for the fuel injection lines.
4. Connect Tool (A) (not shown) to Tool (B) in order to carefully remove fuel injection nozzle
(3) .
Note: Align the centerline of Tool (A) with the extended centerline of fuel injection nozzle
(3). This procedure will help prevent distortion of the fuel injection nozzle which can cause
the fuel injection nozzle to bend or break.
5. Remove the seat washer from the fuel injection nozzle.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 26 09:30:21 UTC+0800 2019
2/2(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GAD
Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01151648
Fuel Injection Nozzles - Install
SMCS - 1254-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00652319
1/2(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
1. Install a new seat washer (5) .
2. Install fuel injection nozzle (3).
3. Install clamp (2), the washer, and bolt (1) that secures the fuel injection nozzle to the
cylinder head assembly.
4. Tighten bolt (1), that secures the fuel injection nozzle, to a torque of 22 N·m (16 lb ft).
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 26 09:31:17 UTC+0800 2019
2/2(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GAD
Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615152
Fuel Shutoff Solenoid - Remove and Install
SMCS - 1259-010
Removal Procedure
Illustration 1 g00618938
1. Disconnect two wire leads (1). Mark the wires for later installation.
2. Disconnect actuator lever (2) from the governor lever.
3. Remove two bolts (3) and washers that secure the fuel shutoff solenoid to the bracket.
4. Remove shutoff solenoid (4) from the bracket.
Installation Procedure
1/2(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Illustration 2 g00618938
1. Place the shutoff solenoid (4) in position on the bracket.
2. Install the two washers and bolts (3) that secure the fuel shutoff solenoid to the bracket.
3. Connect actuator lever (2) to the governor lever.
4. Connect two wire leads (1) to the fuel shutoff solenoid. Ensure that the wires are properly
connected.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 26 09:32:12 UTC+0800 2019
2/2(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GAD
Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565175
Fuel Injection Pump - Remove
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6124 Universal Metric Socket Set 1
B 9U-6128 Universal Metric Socket (1)
1
( 1 )
Part of the Universal Metric Socket Set
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
1/3(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Ensure that the engine is the top center position on number one piston. Refer to Testing and
Adjusting, "Finding Center Position for No. 1 Piston".
Illustration 1 g00813442
2. Remove bolts (1) and washers that secure the cover (2) to the engine front housing.
3. Remove the access cover. Note the timing marks on the fuel injection pump drive gear and
the idler gear for later installation.
Illustration 2 g00813430
2/3(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
4. Scribe a line across the front plate (3) and the mounting flange for the fuel injection pump
(4). This ensures proper alignment for the installation of fuel injection pump (8) .
5. Loosen fitting (5) for oil line (6) .
6. Remove oil line (6) from nipple (7) (not shown).
Note: Put caps or plugs on all openings immediately in order to prevent contamination.
7. Use a lifting sling and a hoist in order to secure the fuel injection pump. The weight of the
fuel injection pump is 13 kg (29 lb).
Note: Use Tool (B) to remove the bolts and the washers that mount the fuel injection pump
(8) .
8. Remove bolt (9) and the washer from the cylinder block.
9. Remove four bolts (10) and the washers that secure the fuel injection pump to the front
housing.
Illustration 3 g00813593
10. Remove the fuel injection pump (8). The gear and the mounting flange will remain with the
fuel injection pump.
Note: The fuel injection pump must be mounted to the engine in order to loosen the nut for
the drive gear.
Note: Do not rotate the engine after the fuel injection pump is removed.
11. Ensure that the old gasket material is removed from all mating surfaces of the pump
mounting flange and the face of the fuel injection pump flange.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 26 09:33:08 UTC+0800 2019
3/3(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GAD
Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565619
Fuel Injection Pump - Install
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part number Part Description Qty
A 9U-6124 Universal Metric Socket Set 1
B 9U-6128 Universal Metric Socket (1)
1
( 1 )
Part of the Universal Metric Socket Set
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: If the nut for the fuel injection pump drive gear is removed, you must tighten the nut
for the fuel injection pump drive gear to 88 ± 5 N·m (65 ± 4 lb ft).
1/2(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Illustration 1 g00813430
1. Use a lifting sling and a hoist in order to secure the fuel injection pump (8). The weight of
the fuel injection pump is 13 kg (29 lb).
2. Install a new gasket and install fuel injection pump (8) .
3. Ensure that the engine is in the top center position on No. 1 piston. Refer to Testing and
Adjusting, "Finding Top Center Position for No. 1 Piston".
4. Ensure that the mark on the front plate (3) and the mark on the fuel injection pump flange
(4) are aligned.
Refer to Testing and Adjusting, "Fuel Injection Timing-Check" for more information on
fuel injection pump timing.
Note: Use Tool (B) to install the bolts and washers that secure the fuel injection pump to the
cylinder block.
5. Install the washers and bolts (9) that secure the fuel injection pump to the engine cylinder
block.
6. Remove the sling from the fuel injection pump.
7. Connect oil line (6) to nipple (7) (not shown).
8. Tighten fitting (5) for oil line (6) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 26 09:34:04 UTC+0800 2019
2/2(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GAD
Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564499
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Remove snap ring (11) from compressor housing (12) .
10. Separate compressor housing (12) from the cartridge (10) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 26 09:35:56 UTC+0800 2019
4/4(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GAD
Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01147762
Turbocharger - Assemble
SMCS - 1052-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: During the assembly procedure, ensure that the index marks are aligned when the
components are assembled.
Illustration 1 g00608452
1/3(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Illustration 2 g00608415
1. Install cartridge (10) into compressor housing (12) .
2. Install snap ring (11) into compressor housing (12) .
Illustration 3 g00608342
3. Install cartridge (10) into turbine housing (9) .
4. Install clamp (8) that secures cartridge (10) and turbine housing (9) together. Install the bolt
and nut (7) into clamp (8).
Note: Refer to the Specifications Module, "Turbocharger" for information on the clamp.
2/3(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Illustration 4 g00608210
5. Inspect the condition of the gaskets. Replace the gaskets, if necessary.
6. Install gasket (6) on the turbine housing.
7. Install gasket (5) on the cartridge.
Illustration 5 g00608212
8. Place oil supply line (4) in position. Secure the oil supply line with bolt (2) (not shown).
9. Place oil return line (3) in position. Secure the oil return line with two bolts (1) .
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 26 09:36:51 UTC+0800 2019
3/3(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GAD
Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564587
Turbocharger - Install
SMCS - 1052-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the condition of all gaskets. Replace the gaskets, if necessary.
Illustration 1 g00608177
1/2(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
2. Install metal gasket (10) (not shown). Install turbocharger (3), oil supply line (4) and oil
return line (6) (not shown) as a unit.
3. Install eight nuts (9). Tighten the nuts to a torque of 41 N·m (30 lb ft).
Note: Two nuts are installed on each turbocharger mounting stud.
Illustration 2 g00812846
4. Slide hose (7) down the oil return line (6) onto fitting (8) .
5. Tighten two clamps (5) on hose (7) .
6. Connect oil supply line (4) to the cylinder block.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 26 09:37:47 UTC+0800 2019
2/2(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GAD
Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565722
Exhaust Manifold - Remove and Install
SMCS - 1059-010
Removal Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00605454
1/3(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
1. Remove the nuts (1) and washers that secure the exhaust manifold to the cylinder head
assembly. The 3066 Engine has twelve nuts and washers while the 3064 Engine has eight
nuts and washers.
2. Remove exhaust manifold (2) from the cylinder head assembly.
3. Remove exhaust manifold gasket (3) that is located between exhaust manifold (2) and the
cylinder head assembly.
Note: The 3066 Engine has two exhaust manifold gaskets, while the 3064 Engine has one
exhaust manifold gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00605454
1. Install exhaust manifold gasket (3) between exhaust manifold (2) and the cylinder head
assembly.
Note: The 3066 Engine has two exhaust manifold gaskets, while the 3064 Engine has one
exhaust manifold gasket.
2. Place exhaust manifold (2) in position on the cylinder head.
3. Install the nuts (1) and the washers that secure the exhaust manifold to the cylinder head
assembly. The 3066 Engine has twelve nuts and washers while the 3064 Engine has eight
nuts and washers.
2/3(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Tighten exhaust manifold nuts (1) to a torque of 18 ± 4 N·m (13 ± 3 lb ft).
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 26 09:38:43 UTC+0800 2019
3/3(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GAD
Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615211
Air Inlet Heater - Remove and Install
SMCS - 1090-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611147
1. Loosen hose clamp (1) that secures air inlet hose (2) to air inlet elbow (4) .
2. Disconnect air inlet hose (2) from air inlet elbow (4) .
1/3(W)
w
2019/10/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...

More Related Content

More from 7fdsjkddmmdm

Caterpillar Cat D25D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...
Caterpillar Cat D25D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...Caterpillar Cat D25D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...
Caterpillar Cat D25D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...
7fdsjkddmmdm
 
Caterpillar Cat D30D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...
Caterpillar Cat D30D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...Caterpillar Cat D30D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...
Caterpillar Cat D30D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...
7fdsjkddmmdm
 
Caterpillar Cat D8N TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7TK) Service R...
Caterpillar Cat D8N TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7TK) Service R...Caterpillar Cat D8N TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7TK) Service R...
Caterpillar Cat D8N TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7TK) Service R...
7fdsjkddmmdm
 
Caterpillar Cat D8L TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7YB) Service R...
Caterpillar Cat D8L TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7YB) Service R...Caterpillar Cat D8L TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7YB) Service R...
Caterpillar Cat D8L TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7YB) Service R...
7fdsjkddmmdm
 
Caterpillar Cat 3054B Industrial Engine (Prefix 5MF) Service Repair Manual (5...
Caterpillar Cat 3054B Industrial Engine (Prefix 5MF) Service Repair Manual (5...Caterpillar Cat 3054B Industrial Engine (Prefix 5MF) Service Repair Manual (5...
Caterpillar Cat 3054B Industrial Engine (Prefix 5MF) Service Repair Manual (5...
7fdsjkddmmdm
 
Caterpillar Cat 740 OEM Articulated Truck (Prefix WWD) Service Repair Manual ...
Caterpillar Cat 740 OEM Articulated Truck (Prefix WWD) Service Repair Manual ...Caterpillar Cat 740 OEM Articulated Truck (Prefix WWD) Service Repair Manual ...
Caterpillar Cat 740 OEM Articulated Truck (Prefix WWD) Service Repair Manual ...
7fdsjkddmmdm
 
Caterpillar Cat 740 Ejector Articulated Truck (Prefix B1R) Service Repair Man...
Caterpillar Cat 740 Ejector Articulated Truck (Prefix B1R) Service Repair Man...Caterpillar Cat 740 Ejector Articulated Truck (Prefix B1R) Service Repair Man...
Caterpillar Cat 740 Ejector Articulated Truck (Prefix B1R) Service Repair Man...
7fdsjkddmmdm
 
Caterpillar Cat 725 OEM Articulated Truck (Prefix WWA) Service Repair Manual ...
Caterpillar Cat 725 OEM Articulated Truck (Prefix WWA) Service Repair Manual ...Caterpillar Cat 725 OEM Articulated Truck (Prefix WWA) Service Repair Manual ...
Caterpillar Cat 725 OEM Articulated Truck (Prefix WWA) Service Repair Manual ...
7fdsjkddmmdm
 
Caterpillar Cat 450F BACKHOE LOADER (Prefix HJR) Service Repair Manual (HJR00...
Caterpillar Cat 450F BACKHOE LOADER (Prefix HJR) Service Repair Manual (HJR00...Caterpillar Cat 450F BACKHOE LOADER (Prefix HJR) Service Repair Manual (HJR00...
Caterpillar Cat 450F BACKHOE LOADER (Prefix HJR) Service Repair Manual (HJR00...
7fdsjkddmmdm
 
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...
7fdsjkddmmdm
 
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...
7fdsjkddmmdm
 
Caterpillar Cat 322L EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 a...
Caterpillar Cat 322L EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 a...Caterpillar Cat 322L EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 a...
Caterpillar Cat 322L EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 a...
7fdsjkddmmdm
 
Caterpillar Cat 322 EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 an...
Caterpillar Cat 322 EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 an...Caterpillar Cat 322 EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 an...
Caterpillar Cat 322 EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 an...
7fdsjkddmmdm
 
Caterpillar Cat 320E LRR Excavator (Prefix TFX) Service Repair Manual (TFX000...
Caterpillar Cat 320E LRR Excavator (Prefix TFX) Service Repair Manual (TFX000...Caterpillar Cat 320E LRR Excavator (Prefix TFX) Service Repair Manual (TFX000...
Caterpillar Cat 320E LRR Excavator (Prefix TFX) Service Repair Manual (TFX000...
7fdsjkddmmdm
 

More from 7fdsjkddmmdm (20)

Caterpillar Cat D25D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...
Caterpillar Cat D25D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...Caterpillar Cat D25D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...
Caterpillar Cat D25D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...
 
New Holland TN75 Tractor Service Repair Manual.pdf
New Holland TN75 Tractor Service Repair Manual.pdfNew Holland TN75 Tractor Service Repair Manual.pdf
New Holland TN75 Tractor Service Repair Manual.pdf
 
New Holland TN65 Tractor Service Repair Manual.pdf
New Holland TN65 Tractor Service Repair Manual.pdfNew Holland TN65 Tractor Service Repair Manual.pdf
New Holland TN65 Tractor Service Repair Manual.pdf
 
New Holland TN70 Tractor Service Repair Manual.pdf
New Holland TN70 Tractor Service Repair Manual.pdfNew Holland TN70 Tractor Service Repair Manual.pdf
New Holland TN70 Tractor Service Repair Manual.pdf
 
New Holland TN55 Tractor Service Repair Manual.pdf
New Holland TN55 Tractor Service Repair Manual.pdfNew Holland TN55 Tractor Service Repair Manual.pdf
New Holland TN55 Tractor Service Repair Manual.pdf
 
Caterpillar Cat D30D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...
Caterpillar Cat D30D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...Caterpillar Cat D30D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...
Caterpillar Cat D30D ARTICULATED TRUCK (Prefix 3AJ) Service Repair Manual (3A...
 
Caterpillar Cat D8N TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7TK) Service R...
Caterpillar Cat D8N TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7TK) Service R...Caterpillar Cat D8N TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7TK) Service R...
Caterpillar Cat D8N TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7TK) Service R...
 
Caterpillar Cat D8L TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7YB) Service R...
Caterpillar Cat D8L TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7YB) Service R...Caterpillar Cat D8L TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7YB) Service R...
Caterpillar Cat D8L TRACK-TYPE TRACTOR Dozer Bulldozer (Prefix 7YB) Service R...
 
Caterpillar Cat 3054B Industrial Engine (Prefix 5MF) Service Repair Manual (5...
Caterpillar Cat 3054B Industrial Engine (Prefix 5MF) Service Repair Manual (5...Caterpillar Cat 3054B Industrial Engine (Prefix 5MF) Service Repair Manual (5...
Caterpillar Cat 3054B Industrial Engine (Prefix 5MF) Service Repair Manual (5...
 
Caterpillar Cat 740 OEM Articulated Truck (Prefix WWD) Service Repair Manual ...
Caterpillar Cat 740 OEM Articulated Truck (Prefix WWD) Service Repair Manual ...Caterpillar Cat 740 OEM Articulated Truck (Prefix WWD) Service Repair Manual ...
Caterpillar Cat 740 OEM Articulated Truck (Prefix WWD) Service Repair Manual ...
 
Caterpillar Cat 740 Ejector Articulated Truck (Prefix B1R) Service Repair Man...
Caterpillar Cat 740 Ejector Articulated Truck (Prefix B1R) Service Repair Man...Caterpillar Cat 740 Ejector Articulated Truck (Prefix B1R) Service Repair Man...
Caterpillar Cat 740 Ejector Articulated Truck (Prefix B1R) Service Repair Man...
 
Caterpillar Cat 725 OEM Articulated Truck (Prefix WWA) Service Repair Manual ...
Caterpillar Cat 725 OEM Articulated Truck (Prefix WWA) Service Repair Manual ...Caterpillar Cat 725 OEM Articulated Truck (Prefix WWA) Service Repair Manual ...
Caterpillar Cat 725 OEM Articulated Truck (Prefix WWA) Service Repair Manual ...
 
Caterpillar Cat 450F BACKHOE LOADER (Prefix HJR) Service Repair Manual (HJR00...
Caterpillar Cat 450F BACKHOE LOADER (Prefix HJR) Service Repair Manual (HJR00...Caterpillar Cat 450F BACKHOE LOADER (Prefix HJR) Service Repair Manual (HJR00...
Caterpillar Cat 450F BACKHOE LOADER (Prefix HJR) Service Repair Manual (HJR00...
 
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...
 
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...
 
Caterpillar Cat 322L EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 a...
Caterpillar Cat 322L EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 a...Caterpillar Cat 322L EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 a...
Caterpillar Cat 322L EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 a...
 
Caterpillar Cat 322 EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 an...
Caterpillar Cat 322 EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 an...Caterpillar Cat 322 EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 an...
Caterpillar Cat 322 EXCAVATOR (Prefix 8CL) Service Repair Manual (8CL00001 an...
 
CASE DV207 Vibratory Roller Service Repair Manual.pdf
CASE DV207 Vibratory Roller Service Repair Manual.pdfCASE DV207 Vibratory Roller Service Repair Manual.pdf
CASE DV207 Vibratory Roller Service Repair Manual.pdf
 
Caterpillar Cat 320E LRR Excavator (Prefix TFX) Service Repair Manual (TFX000...
Caterpillar Cat 320E LRR Excavator (Prefix TFX) Service Repair Manual (TFX000...Caterpillar Cat 320E LRR Excavator (Prefix TFX) Service Repair Manual (TFX000...
Caterpillar Cat 320E LRR Excavator (Prefix TFX) Service Repair Manual (TFX000...
 
CASE DV207HF Vibratory Roller Service Repair Manual.pdf
CASE DV207HF Vibratory Roller Service Repair Manual.pdfCASE DV207HF Vibratory Roller Service Repair Manual.pdf
CASE DV207HF Vibratory Roller Service Repair Manual.pdf
 

Recently uploaded

Goa ] Virgin Call Girls Panaji ₹7.5k Pick Up & Drop With Cash Payment 9701288...
Goa ] Virgin Call Girls Panaji ₹7.5k Pick Up & Drop With Cash Payment 9701288...Goa ] Virgin Call Girls Panaji ₹7.5k Pick Up & Drop With Cash Payment 9701288...
Goa ] Virgin Call Girls Panaji ₹7.5k Pick Up & Drop With Cash Payment 9701288...
Call Girls Mumbai
 
👉Goa Call Girl Service👉📞9701288194👉📞 Just📲 Call Rajveer Call Girls Service In...
👉Goa Call Girl Service👉📞9701288194👉📞 Just📲 Call Rajveer Call Girls Service In...👉Goa Call Girl Service👉📞9701288194👉📞 Just📲 Call Rajveer Call Girls Service In...
👉Goa Call Girl Service👉📞9701288194👉📞 Just📲 Call Rajveer Call Girls Service In...
Call Girls Mumbai
 
一比一原版伯明翰城市大学毕业证成绩单留信学历认证
一比一原版伯明翰城市大学毕业证成绩单留信学历认证一比一原版伯明翰城市大学毕业证成绩单留信学历认证
一比一原版伯明翰城市大学毕业证成绩单留信学历认证
62qaf0hi
 
Bhubaneswar Call Girls 💯Call Us 🔝 9777949614 🔝 💃 Top Class Russian Bhubaneswa...
Bhubaneswar Call Girls 💯Call Us 🔝 9777949614 🔝 💃 Top Class Russian Bhubaneswa...Bhubaneswar Call Girls 💯Call Us 🔝 9777949614 🔝 💃 Top Class Russian Bhubaneswa...
Bhubaneswar Call Girls 💯Call Us 🔝 9777949614 🔝 💃 Top Class Russian Bhubaneswa...
jaspritkaur4u
 
Bhubaneswar Call Girls Service {9777949614 } ❤️VVIP ROCKY Call Girl in Bhuban...
Bhubaneswar Call Girls Service {9777949614 } ❤️VVIP ROCKY Call Girl in Bhuban...Bhubaneswar Call Girls Service {9777949614 } ❤️VVIP ROCKY Call Girl in Bhuban...
Bhubaneswar Call Girls Service {9777949614 } ❤️VVIP ROCKY Call Girl in Bhuban...
Call Girls Mumbai
 
一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样
一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样
一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样
zovambe
 
如何办理伦敦商学院毕业证(LBS毕业证)毕业证成绩单原版一比一
如何办理伦敦商学院毕业证(LBS毕业证)毕业证成绩单原版一比一如何办理伦敦商学院毕业证(LBS毕业证)毕业证成绩单原版一比一
如何办理伦敦商学院毕业证(LBS毕业证)毕业证成绩单原版一比一
avy6anjnd
 
如何办理(Waterloo毕业证书)滑铁卢大学毕业证毕业证成绩单原版一比一
如何办理(Waterloo毕业证书)滑铁卢大学毕业证毕业证成绩单原版一比一如何办理(Waterloo毕业证书)滑铁卢大学毕业证毕业证成绩单原版一比一
如何办理(Waterloo毕业证书)滑铁卢大学毕业证毕业证成绩单原版一比一
avy6anjnd
 
如何办理美国华盛顿大学毕业证(UW毕业证书)毕业证成绩单原版一比一
如何办理美国华盛顿大学毕业证(UW毕业证书)毕业证成绩单原版一比一如何办理美国华盛顿大学毕业证(UW毕业证书)毕业证成绩单原版一比一
如何办理美国华盛顿大学毕业证(UW毕业证书)毕业证成绩单原版一比一
avy6anjnd
 

Recently uploaded (20)

Preparing for Transportation Electrification: The Electric Coop Perspective
Preparing for Transportation Electrification: The Electric Coop PerspectivePreparing for Transportation Electrification: The Electric Coop Perspective
Preparing for Transportation Electrification: The Electric Coop Perspective
 
EV Charging Resources and Technical Assistance for Rural Communities and Trib...
EV Charging Resources and Technical Assistance for Rural Communities and Trib...EV Charging Resources and Technical Assistance for Rural Communities and Trib...
EV Charging Resources and Technical Assistance for Rural Communities and Trib...
 
Goa ] Virgin Call Girls Panaji ₹7.5k Pick Up & Drop With Cash Payment 9701288...
Goa ] Virgin Call Girls Panaji ₹7.5k Pick Up & Drop With Cash Payment 9701288...Goa ] Virgin Call Girls Panaji ₹7.5k Pick Up & Drop With Cash Payment 9701288...
Goa ] Virgin Call Girls Panaji ₹7.5k Pick Up & Drop With Cash Payment 9701288...
 
👉Goa Call Girl Service👉📞9701288194👉📞 Just📲 Call Rajveer Call Girls Service In...
👉Goa Call Girl Service👉📞9701288194👉📞 Just📲 Call Rajveer Call Girls Service In...👉Goa Call Girl Service👉📞9701288194👉📞 Just📲 Call Rajveer Call Girls Service In...
👉Goa Call Girl Service👉📞9701288194👉📞 Just📲 Call Rajveer Call Girls Service In...
 
一比一原版伯明翰城市大学毕业证成绩单留信学历认证
一比一原版伯明翰城市大学毕业证成绩单留信学历认证一比一原版伯明翰城市大学毕业证成绩单留信学历认证
一比一原版伯明翰城市大学毕业证成绩单留信学历认证
 
Bhubaneswar Call Girls 💯Call Us 🔝 9777949614 🔝 💃 Top Class Russian Bhubaneswa...
Bhubaneswar Call Girls 💯Call Us 🔝 9777949614 🔝 💃 Top Class Russian Bhubaneswa...Bhubaneswar Call Girls 💯Call Us 🔝 9777949614 🔝 💃 Top Class Russian Bhubaneswa...
Bhubaneswar Call Girls 💯Call Us 🔝 9777949614 🔝 💃 Top Class Russian Bhubaneswa...
 
Bhubaneswar Call Girls Service {9777949614 } ❤️VVIP ROCKY Call Girl in Bhuban...
Bhubaneswar Call Girls Service {9777949614 } ❤️VVIP ROCKY Call Girl in Bhuban...Bhubaneswar Call Girls Service {9777949614 } ❤️VVIP ROCKY Call Girl in Bhuban...
Bhubaneswar Call Girls Service {9777949614 } ❤️VVIP ROCKY Call Girl in Bhuban...
 
Low Cost Jhansi 📞6378878445📞 Just📲 Call Inaaya Call Girls Service No💰Advance ...
Low Cost Jhansi 📞6378878445📞 Just📲 Call Inaaya Call Girls Service No💰Advance ...Low Cost Jhansi 📞6378878445📞 Just📲 Call Inaaya Call Girls Service No💰Advance ...
Low Cost Jhansi 📞6378878445📞 Just📲 Call Inaaya Call Girls Service No💰Advance ...
 
一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样
一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样
一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样
 
Exclusive Jhansi Call Girls (Adult Only) 💯Call Us 🔝 6378878445 🔝 💃 Escort Ser...
Exclusive Jhansi Call Girls (Adult Only) 💯Call Us 🔝 6378878445 🔝 💃 Escort Ser...Exclusive Jhansi Call Girls (Adult Only) 💯Call Us 🔝 6378878445 🔝 💃 Escort Ser...
Exclusive Jhansi Call Girls (Adult Only) 💯Call Us 🔝 6378878445 🔝 💃 Escort Ser...
 
JOHN DEERE 7200R 7215R 7230R 7260R 7280R TECHNICAL SERVICE PDF MANUAL 2680PGS...
JOHN DEERE 7200R 7215R 7230R 7260R 7280R TECHNICAL SERVICE PDF MANUAL 2680PGS...JOHN DEERE 7200R 7215R 7230R 7260R 7280R TECHNICAL SERVICE PDF MANUAL 2680PGS...
JOHN DEERE 7200R 7215R 7230R 7260R 7280R TECHNICAL SERVICE PDF MANUAL 2680PGS...
 
SEM 922 MOTOR GRADER PARTS LIST, ALL WHEEL DRIVE
SEM 922 MOTOR GRADER PARTS LIST, ALL WHEEL DRIVESEM 922 MOTOR GRADER PARTS LIST, ALL WHEEL DRIVE
SEM 922 MOTOR GRADER PARTS LIST, ALL WHEEL DRIVE
 
如何办理伦敦商学院毕业证(LBS毕业证)毕业证成绩单原版一比一
如何办理伦敦商学院毕业证(LBS毕业证)毕业证成绩单原版一比一如何办理伦敦商学院毕业证(LBS毕业证)毕业证成绩单原版一比一
如何办理伦敦商学院毕业证(LBS毕业证)毕业证成绩单原版一比一
 
如何办理(Waterloo毕业证书)滑铁卢大学毕业证毕业证成绩单原版一比一
如何办理(Waterloo毕业证书)滑铁卢大学毕业证毕业证成绩单原版一比一如何办理(Waterloo毕业证书)滑铁卢大学毕业证毕业证成绩单原版一比一
如何办理(Waterloo毕业证书)滑铁卢大学毕业证毕业证成绩单原版一比一
 
Effortless Driving Experience Premier Mercedes Sprinter Suspension Service
Effortless Driving Experience Premier Mercedes Sprinter Suspension ServiceEffortless Driving Experience Premier Mercedes Sprinter Suspension Service
Effortless Driving Experience Premier Mercedes Sprinter Suspension Service
 
👉 Agartala Call Girls Service Just Call 🍑👄6378878445 🍑👄 Top Class Call Girl S...
👉 Agartala Call Girls Service Just Call 🍑👄6378878445 🍑👄 Top Class Call Girl S...👉 Agartala Call Girls Service Just Call 🍑👄6378878445 🍑👄 Top Class Call Girl S...
👉 Agartala Call Girls Service Just Call 🍑👄6378878445 🍑👄 Top Class Call Girl S...
 
John deere 7200r 7230R 7260R Problems Repair Manual
John deere 7200r 7230R 7260R Problems Repair ManualJohn deere 7200r 7230R 7260R Problems Repair Manual
John deere 7200r 7230R 7260R Problems Repair Manual
 
Things that make the new Nissan Z unique
Things that make the new Nissan Z uniqueThings that make the new Nissan Z unique
Things that make the new Nissan Z unique
 
如何办理美国华盛顿大学毕业证(UW毕业证书)毕业证成绩单原版一比一
如何办理美国华盛顿大学毕业证(UW毕业证书)毕业证成绩单原版一比一如何办理美国华盛顿大学毕业证(UW毕业证书)毕业证成绩单原版一比一
如何办理美国华盛顿大学毕业证(UW毕业证书)毕业证成绩单原版一比一
 
What Does It Mean When Mercedes Says 'ESP Inoperative See Owner's Manual'
What Does It Mean When Mercedes Says 'ESP Inoperative See Owner's Manual'What Does It Mean When Mercedes Says 'ESP Inoperative See Owner's Manual'
What Does It Mean When Mercedes Says 'ESP Inoperative See Owner's Manual'
 

Caterpillar Cat 320C LRR Excavator (Prefix GAD) Service Repair Manual (GAD00001 and up).pdf

  • 2. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01564836 Fuel Filter Base - Remove and Install SMCS - 1262-010 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 185-3630 Strap Wrench Assembly 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. 1/4(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 3. Dispose of all fluids according to local regulations and mandates. Illustration 1 g00813127 1. Use Tool (A) to remove fuel filter (3) from fuel filter base (2) . Note: It is not necessary to remove the fuel filter in order to remove the fuel filter base. 2. Remove banjo bolts (1) and copper washers in order to disconnect the fuel lines (4) from the fuel filter base (2). Note: Cap all openings or plug all openings immediately in order to prevent contamination of the fuel system. Illustration 2 g00813147 3. Remove two bolts (5) and the washers that secure the fuel filter base (2) to the air inlet manifold. Remove the fuel filter base (2) from the fuel filter bracket. Installation Procedure 2/4(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 4. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 3 g00813147 1. Place the fuel filter base (2) in position on the fuel filter bracket. Install the washers and two bolts (5) that secure the fuel filter base tothe fuel filter bracket. Illustration 4 g00813127 2. Install the banjo bolts (1) and install new copper washers in order to connect the fuel lines (4) to the fuel filter base (2) . 3. If the fuel filter was removed, install the fuel filter (3) to the fuel filter base (2). Tighten the fuel filter by hand according to the instructions that are shown on the fuel filter. Do not overtighten the fuel filter. 3/4(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 5. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01565021 Fuel Injection Lines - Remove and Install SMCS - 1252-010 Removal Procedure Start By: A. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1/5(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 6. Illustration 1 g00606301 The 3066 Engine is shown. 1. Remove the bolts (1), the washers, and the clamps (2), which secure the fuel lines to the inlet manifold (3) . Illustration 2 g00606310 2. Disconnect the fuel injection lines (4) from the fuel injection nozzles (5) . Note: Cap all openings or plug all openings immediately in order to prevent contamination of the fuel system. 2/5(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 7. Illustration 3 g00606314 Fuel injection pump for a 3066 Engine 3. Disconnect the end of the fuel injection lines (4) from the fuel injection pump (6) . Note: Cap all openings or plug all openings immediately in order to prevent contamination of the fuel system. 4. Remove the fuel injection lines (4) from the engine. Illustration 4 g00606317 5. Loosen the acorn nuts (7), which secure the fuel return line to the fuel injection nozzles. 6. Remove one bolt (8) and the washer from the clamp that secures the fuel return line to the intake manifold. Note: The clamp will remain with the fuel return line, when the fuel return line is removed from the engine. 7. Disconnect fitting (9). Remove fuel return line (10) from the engine. Note: Cap all openings or plug all openings immediately in order to prevent contamination of the fuel system. 3/5(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 8. Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 5 g00606317 1. Place the fuel return line (10) in position on the engine. Connect fitting (9) of the fuel return line to the fuel injection pump. 2. Install the washer and bolt (8) through the clamp in order to secure the fuel return line to the inlet manifold. 3. Install the fuel return line (10) to the fuel injection nozzles. Secure the fuel return line to the fuel injection nozzle with acorn nuts (7) . 4/5(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 9. Illustration 6 g00606399 Fuel injection pump for a 3066 Engine 4. Place the fuel injection lines (4) on the engine. 5. Connect the fuel injection lines (4) to the fuel injection pump (6) . 6. Connect the fuel injection lines (4) to the fuel injection nozzles (5) . Note: The fuel lines (4) should be connected at the fuel injection nozzle (5) and at the fuel injection pump (6) before tightening the nuts for the fuel injection line. 7. Tighten the nuts for the fuel injection line to a torque of 25 N·m (18 lb ft). Illustration 7 g00606301 Fuel lines for a 3066 Engine 8. Install the clamps (2), the washers, and the bolts (1), which secure the fuel lines to the inlet manifold (3) . End By: Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install". Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Oct 26 09:29:25 UTC+0800 2019 5/5(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 10. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01151321 Fuel Injection Nozzles - Remove SMCS - 1254-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1U-7600 Slide Hammer Puller 1 B 9U-6278 Adapter 1 Start By: A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/2(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 11. Illustration 1 g00652319 1. Remove bolt (1) and the washer that secures the clamp (2) to the cylinder head assembly. 2. Remove the clamp (2) that secures the fuel injection nozzle (3) in position in the cylinder head assembly. Note: Put caps or plugs on all openings immediately in order to prevent contamination in the fuel system. Note: Mark the clamp for later installation. 3. Install Tool (B) (not shown) to the fuel injection nozzle. Note: Tool (B) is installed at the connection (4) for the fuel injection lines. 4. Connect Tool (A) (not shown) to Tool (B) in order to carefully remove fuel injection nozzle (3) . Note: Align the centerline of Tool (A) with the extended centerline of fuel injection nozzle (3). This procedure will help prevent distortion of the fuel injection nozzle which can cause the fuel injection nozzle to bend or break. 5. Remove the seat washer from the fuel injection nozzle. Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Oct 26 09:30:21 UTC+0800 2019 2/2(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 12. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01151648 Fuel Injection Nozzles - Install SMCS - 1254-012 Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00652319 1/2(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 13. 1. Install a new seat washer (5) . 2. Install fuel injection nozzle (3). 3. Install clamp (2), the washer, and bolt (1) that secures the fuel injection nozzle to the cylinder head assembly. 4. Tighten bolt (1), that secures the fuel injection nozzle, to a torque of 22 N·m (16 lb ft). End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install". Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Oct 26 09:31:17 UTC+0800 2019 2/2(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 14. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01615152 Fuel Shutoff Solenoid - Remove and Install SMCS - 1259-010 Removal Procedure Illustration 1 g00618938 1. Disconnect two wire leads (1). Mark the wires for later installation. 2. Disconnect actuator lever (2) from the governor lever. 3. Remove two bolts (3) and washers that secure the fuel shutoff solenoid to the bracket. 4. Remove shutoff solenoid (4) from the bracket. Installation Procedure 1/2(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 15. Illustration 2 g00618938 1. Place the shutoff solenoid (4) in position on the bracket. 2. Install the two washers and bolts (3) that secure the fuel shutoff solenoid to the bracket. 3. Connect actuator lever (2) to the governor lever. 4. Connect two wire leads (1) to the fuel shutoff solenoid. Ensure that the wires are properly connected. Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Oct 26 09:32:12 UTC+0800 2019 2/2(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 16. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01565175 Fuel Injection Pump - Remove SMCS - 1251-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 9U-6124 Universal Metric Socket Set 1 B 9U-6128 Universal Metric Socket (1) 1 ( 1 ) Part of the Universal Metric Socket Set Start By: A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair 1/3(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 17. of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1. Ensure that the engine is the top center position on number one piston. Refer to Testing and Adjusting, "Finding Center Position for No. 1 Piston". Illustration 1 g00813442 2. Remove bolts (1) and washers that secure the cover (2) to the engine front housing. 3. Remove the access cover. Note the timing marks on the fuel injection pump drive gear and the idler gear for later installation. Illustration 2 g00813430 2/3(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 18. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
  • 19. 4. Scribe a line across the front plate (3) and the mounting flange for the fuel injection pump (4). This ensures proper alignment for the installation of fuel injection pump (8) . 5. Loosen fitting (5) for oil line (6) . 6. Remove oil line (6) from nipple (7) (not shown). Note: Put caps or plugs on all openings immediately in order to prevent contamination. 7. Use a lifting sling and a hoist in order to secure the fuel injection pump. The weight of the fuel injection pump is 13 kg (29 lb). Note: Use Tool (B) to remove the bolts and the washers that mount the fuel injection pump (8) . 8. Remove bolt (9) and the washer from the cylinder block. 9. Remove four bolts (10) and the washers that secure the fuel injection pump to the front housing. Illustration 3 g00813593 10. Remove the fuel injection pump (8). The gear and the mounting flange will remain with the fuel injection pump. Note: The fuel injection pump must be mounted to the engine in order to loosen the nut for the drive gear. Note: Do not rotate the engine after the fuel injection pump is removed. 11. Ensure that the old gasket material is removed from all mating surfaces of the pump mounting flange and the face of the fuel injection pump flange. Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Oct 26 09:33:08 UTC+0800 2019 3/3(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 20. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01565619 Fuel Injection Pump - Install SMCS - 1251-012 Installation Procedure Table 1 Required Tools Tool Part number Part Description Qty A 9U-6124 Universal Metric Socket Set 1 B 9U-6128 Universal Metric Socket (1) 1 ( 1 ) Part of the Universal Metric Socket Set NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: If the nut for the fuel injection pump drive gear is removed, you must tighten the nut for the fuel injection pump drive gear to 88 ± 5 N·m (65 ± 4 lb ft). 1/2(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 21. Illustration 1 g00813430 1. Use a lifting sling and a hoist in order to secure the fuel injection pump (8). The weight of the fuel injection pump is 13 kg (29 lb). 2. Install a new gasket and install fuel injection pump (8) . 3. Ensure that the engine is in the top center position on No. 1 piston. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston". 4. Ensure that the mark on the front plate (3) and the mark on the fuel injection pump flange (4) are aligned. Refer to Testing and Adjusting, "Fuel Injection Timing-Check" for more information on fuel injection pump timing. Note: Use Tool (B) to install the bolts and washers that secure the fuel injection pump to the cylinder block. 5. Install the washers and bolts (9) that secure the fuel injection pump to the engine cylinder block. 6. Remove the sling from the fuel injection pump. 7. Connect oil line (6) to nipple (7) (not shown). 8. Tighten fitting (5) for oil line (6) . Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Oct 26 09:34:04 UTC+0800 2019 2/2(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 22. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01564499 Turbocharger - Remove SMCS - 1052-011 Removal Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1/3(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 23. 9. Remove snap ring (11) from compressor housing (12) . 10. Separate compressor housing (12) from the cartridge (10) . Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Oct 26 09:35:56 UTC+0800 2019 4/4(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 24. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01147762 Turbocharger - Assemble SMCS - 1052-016 Assembly Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: During the assembly procedure, ensure that the index marks are aligned when the components are assembled. Illustration 1 g00608452 1/3(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 25. Illustration 2 g00608415 1. Install cartridge (10) into compressor housing (12) . 2. Install snap ring (11) into compressor housing (12) . Illustration 3 g00608342 3. Install cartridge (10) into turbine housing (9) . 4. Install clamp (8) that secures cartridge (10) and turbine housing (9) together. Install the bolt and nut (7) into clamp (8). Note: Refer to the Specifications Module, "Turbocharger" for information on the clamp. 2/3(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 26. Illustration 4 g00608210 5. Inspect the condition of the gaskets. Replace the gaskets, if necessary. 6. Install gasket (6) on the turbine housing. 7. Install gasket (5) on the cartridge. Illustration 5 g00608212 8. Place oil supply line (4) in position. Secure the oil supply line with bolt (2) (not shown). 9. Place oil return line (3) in position. Secure the oil return line with two bolts (1) . End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install". Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Oct 26 09:36:51 UTC+0800 2019 3/3(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 27. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01564587 Turbocharger - Install SMCS - 1052-012 Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Inspect the condition of all gaskets. Replace the gaskets, if necessary. Illustration 1 g00608177 1/2(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 28. 2. Install metal gasket (10) (not shown). Install turbocharger (3), oil supply line (4) and oil return line (6) (not shown) as a unit. 3. Install eight nuts (9). Tighten the nuts to a torque of 41 N·m (30 lb ft). Note: Two nuts are installed on each turbocharger mounting stud. Illustration 2 g00812846 4. Slide hose (7) down the oil return line (6) onto fitting (8) . 5. Tighten two clamps (5) on hose (7) . 6. Connect oil supply line (4) to the cylinder block. Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Oct 26 09:37:47 UTC+0800 2019 2/2(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 29. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01565722 Exhaust Manifold - Remove and Install SMCS - 1059-010 Removal Procedure Start By: A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00605454 1/3(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 30. 1. Remove the nuts (1) and washers that secure the exhaust manifold to the cylinder head assembly. The 3066 Engine has twelve nuts and washers while the 3064 Engine has eight nuts and washers. 2. Remove exhaust manifold (2) from the cylinder head assembly. 3. Remove exhaust manifold gasket (3) that is located between exhaust manifold (2) and the cylinder head assembly. Note: The 3066 Engine has two exhaust manifold gaskets, while the 3064 Engine has one exhaust manifold gasket. Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 2 g00605454 1. Install exhaust manifold gasket (3) between exhaust manifold (2) and the cylinder head assembly. Note: The 3066 Engine has two exhaust manifold gaskets, while the 3064 Engine has one exhaust manifold gasket. 2. Place exhaust manifold (2) in position on the cylinder head. 3. Install the nuts (1) and the washers that secure the exhaust manifold to the cylinder head assembly. The 3066 Engine has twelve nuts and washers while the 3064 Engine has eight nuts and washers. 2/3(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 31. 4. Tighten exhaust manifold nuts (1) to a torque of 18 ± 4 N·m (13 ± 3 lb ft). End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install". Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Oct 26 09:38:43 UTC+0800 2019 3/3(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
  • 32. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01615211 Air Inlet Heater - Remove and Install SMCS - 1090-010 Removal Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00611147 1. Loosen hose clamp (1) that secures air inlet hose (2) to air inlet elbow (4) . 2. Disconnect air inlet hose (2) from air inlet elbow (4) . 1/3(W) w 2019/10/26 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...