This document provides instructions for removing and installing inlet and exhaust valves on a C27 Industrial Engine. It describes:
- Using a valve spring compressor tool to remove the valve springs and valve spring retainers.
- Inspecting the valves and checking the spring force.
- Lubricating the valve stems before installation and compressing the springs with a tool to install the retainers.
- Cautions for wearing protective equipment when working with springs to avoid injury from parts propelled by the springs.
This document provides instructions for removing inlet and exhaust valve seat inserts from the cylinder head of a C27 Industrial Engine. Key points include:
- Use a valve seat cutter and reamer to remove the existing valve seat insert.
- Inspect the cylinder head bore for any damage or wear after removal of the insert.
- Thoroughly clean the cylinder head bore before installing a new valve seat insert.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
- Inlet and exhaust valve springs
- Inlet and exhaust valves
- Inlet and exhaust valve guides
- Inlet and exhaust valve seat inserts
- Engine oil filter base
The procedures describe the required tools, removal steps, inspection, installation steps, and safety precautions for each component. Detailed illustrations supplement the text instructions.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
- Inlet and exhaust valve springs
- Inlet and exhaust valves
- Inlet and exhaust valve guides
- Inlet and exhaust valve seat inserts
- Engine oil filter base
The procedures describe the required tools, removal steps, inspection, installation steps, and safety precautions for each component. Detailed illustrations supplement the text instructions.
The document provides instructions for removing and installing inlet and exhaust valve springs on a C27 Industrial Engine.
It describes the required tools and gives a step-by-step process for removing the valve springs which includes using a valve spring compressor tool to compress the springs so the spring keepers can be removed from the valve. It then provides instructions for installing new valve springs which involves lubricating the valves, compressing the springs with the tool to insert the spring keepers.
The document also provides procedures for removing and installing inlet and exhaust valve guides from the cylinder head using driver tools to remove and install the guides at the proper height. Lubrication and sealing of the guides is described.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure to remove the engine oil filter base, oil cooler, and draining coolant, requiring draining fluids and disconnecting hoses.
This document provides instructions for removing inlet and exhaust valve seat inserts from the cylinder head of a C27 Industrial Engine. Key points include:
- Use a valve seat cutter and reamer to remove the existing valve seat insert.
- Inspect the cylinder head bore for any damage or wear after removal of the insert.
- Thoroughly clean the cylinder head bore before installing a new valve seat insert.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
- Inlet and exhaust valve springs
- Inlet and exhaust valves
- Inlet and exhaust valve guides
- Inlet and exhaust valve seat inserts
- Engine oil filter base
The procedures describe the required tools, removal steps, inspection, installation steps, and safety precautions for each component. Detailed illustrations supplement the text instructions.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
- Inlet and exhaust valve springs
- Inlet and exhaust valves
- Inlet and exhaust valve guides
- Inlet and exhaust valve seat inserts
- Engine oil filter base
The procedures describe the required tools, removal steps, inspection, installation steps, and safety precautions for each component. Detailed illustrations supplement the text instructions.
The document provides instructions for removing and installing inlet and exhaust valve springs on a C27 Industrial Engine.
It describes the required tools and gives a step-by-step process for removing the valve springs which includes using a valve spring compressor tool to compress the springs so the spring keepers can be removed from the valve. It then provides instructions for installing new valve springs which involves lubricating the valves, compressing the springs with the tool to insert the spring keepers.
The document also provides procedures for removing and installing inlet and exhaust valve guides from the cylinder head using driver tools to remove and install the guides at the proper height. Lubrication and sealing of the guides is described.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure to remove the engine oil filter base, oil cooler, and draining coolant, requiring draining fluids and disconnecting hoses.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure for removing the engine oil filter base, oil cooler, and draining coolant in preparation for further maintenance. Safety notices are provided regarding containment of fluids.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure for removing the engine oil filter base, oil cooler, and draining coolant in preparation for maintenance.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Inlet and exhaust valves, guides, and seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2) The engine oil filter base, oil cooler, and oil pump. It instructs to drain fluids, then remove mounting bolts and connectors to take parts off.
3) Safety precautions are emphasized such as keeping parts clean, containing fluids, and wearing protective equipment when working with spring-loaded parts.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Inlet and exhaust valves, valve guides, and valve seat inserts.
2) The engine oil filter base, oil cooler, and engine oil pump.
3) Safety precautions and required tools are listed for each procedure. Detailed illustrations and step-by-step instructions are provided.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure for removing the engine oil filter base, oil cooler, and draining coolant in preparation for maintenance.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height is achieved.
3) Valve seat inserts using an extractor tool and driver tools.
4) The engine oil filter base and related internal parts, noting any spring loaded components.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height is achieved.
3) Valve seat inserts using an extractor tool and driver tools.
4) The engine oil filter base and related internal parts, noting any spring loaded components.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine, including:
1) Valves, springs, and related parts. Tools are needed to compress springs safely.
2) Valve guides. Guides must be installed to the correct height specification.
3) Valve seat inserts. New inserts must be cooled before installation.
4) The oil filter base. Springs under covers require care during removal.
The document suggests that if clicking the above button is invalid, the user should first download the document and then click the link to download the complete manual. It thanks the reader for their time.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using tools to set specifications like the lift-off limitation. Precautions are provided to prevent contamination and release of spring forces during the process.
More Related Content
Similar to Caterpillar Cat C27 Industrial Engine (Prefix JFJ) Service Repair Manual Instant Download.pdf
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure for removing the engine oil filter base, oil cooler, and draining coolant in preparation for further maintenance. Safety notices are provided regarding containment of fluids.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure for removing the engine oil filter base, oil cooler, and draining coolant in preparation for maintenance.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Inlet and exhaust valves, guides, and seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2) The engine oil filter base, oil cooler, and oil pump. It instructs to drain fluids, then remove mounting bolts and connectors to take parts off.
3) Safety precautions are emphasized such as keeping parts clean, containing fluids, and wearing protective equipment when working with spring-loaded parts.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Inlet and exhaust valves, valve guides, and valve seat inserts.
2) The engine oil filter base, oil cooler, and engine oil pump.
3) Safety precautions and required tools are listed for each procedure. Detailed illustrations and step-by-step instructions are provided.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure for removing the engine oil filter base, oil cooler, and draining coolant in preparation for maintenance.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height is achieved.
3) Valve seat inserts using an extractor tool and driver tools.
4) The engine oil filter base and related internal parts, noting any spring loaded components.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height is achieved.
3) Valve seat inserts using an extractor tool and driver tools.
4) The engine oil filter base and related internal parts, noting any spring loaded components.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine, including:
1) Valves, springs, and related parts. Tools are needed to compress springs safely.
2) Valve guides. Guides must be installed to the correct height specification.
3) Valve seat inserts. New inserts must be cooled before installation.
4) The oil filter base. Springs under covers require care during removal.
Similar to Caterpillar Cat C27 Industrial Engine (Prefix JFJ) Service Repair Manual Instant Download.pdf (20)
The document suggests that if clicking the above button is invalid, the user should first download the document and then click the link to download the complete manual. It thanks the reader for their time.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using tools to set specifications like the lift-off limitation. Precautions are provided to prevent contamination and release of spring forces during the process.
This document provides instructions for assembling the main hydraulic pump of an excavator model. It lists 49 steps and includes illustrations of each step. The steps include installing various parts like bearings, seals, pistons, springs, and valves. Tools needed are also listed. The summary concludes by stating to install the main hydraulic pump by referring to another section of the repair manual.
The document provides instructions for installing a swing drive on an excavator model M315D. It lists the required tools and parts. The procedure involves 28 steps, including installing bearings, seals, gears, and other components into the swing drive housing. Specific torque specifications and dimensional checks are listed to ensure proper assembly. Installation is completed by positioning the swing drive in the swing brake housing and securing it with bolts.
This document provides instructions for removing and installing a pilot control valve on a D10 track-type tractor. Key steps include:
1. Removing the right side console cover and disconnecting control rods and oil lines from the valve.
2. Removing bolts to take the valve off its mounting bracket.
3. Installing the valve by connecting oil lines and control rods and securing it with bolts back on the bracket.
This document provides instructions for disassembling and assembling the final drive of a D9R track-type tractor. It describes removing components such as the planetary carrier, gears, shafts, and hub. Various tools are required, including link brackets, a push-puller tool group, driver group, and hydraulic cylinder assembly. Precautions are given for using hydraulic cylinders and puller studs during disassembly. The multi-step process includes pressing, lifting, and removing components from the planetary carrier, sun gear, and hub.
1) The document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor.
2) It describes using various tools to remove over 30 components of the final drive including gears, shafts, seals, and hubs.
3) Precautions are included when using hydraulic cylinders and heated components to disassemble pieces.
1) The document provides instructions for removing and installing the final drive planetary carrier in a D9R track-type tractor.
2) It describes using various tools to remove the carrier, hub components, seals, and gears. It also explains how to reinstall these parts in reverse order.
3) Fourteen steps are outlined for removal and thirteen steps for installation, ensuring proper alignment of parts and torquing of bolts.
The document provides instructions for disassembling and assembling the steering clutch and brake of a D7R track-type tractor. It describes 20 steps to disassemble the components and 19 steps to reassemble them. These include removing plates, seals, springs, and other parts, and replacing them in the reverse order. Tools required include link brackets and a driver group. Proper spring loading and seal installation are emphasized.
This document provides instructions for assembling and installing the final drive on a D7R track-type tractor. It describes 31 steps for assembly, including installing seals, bearings, gears, shafts and covers. For installation, it outlines 10 steps such as positioning the final drive, installing bolts, filling it with oil and reconnecting the track. The document contains diagrams to illustrate each step in the process.
Caterpillar Cat D7R II WATER FORDING TRACTOR (Prefix DJT) Service Repair Manu...ze3xiandiao
This document provides instructions for disassembling and assembling the steering planetary and brake of a D7R Series II Water Fording Tractor. It describes removing 24 components including the planetary group, brake, ring gear, friction discs, piston, and springs. Reassembly involves installing these components in reverse order, noting proper orientation and torque specifications. Tools required include link brackets, a driver group, forcing bolts, and sealant.
Caterpillar Cat D7R II TRACK-TYPE TRACTOR (Prefix AGN) Service Repair Manual ...ze3xiandiao
The document provides instructions for removing a final drive, steering planetary, and brake assembly from a D7R II track-type tractor. It describes using lifting brackets, shackles, bolts and nuts to attach a hoist to the assembly and remove it from the tractor. The assembly weighs approximately 800 kg (1750 lb) and precautions are listed to provide means to stop the machine without the brake installed. Fluids must be contained while working on components to collect any fluids that may drain out.
The document provides instructions for disassembling and assembling the final drives of a D7H track-type tractor. Key steps include removing the final drives from the tractor frame using specialized tools, then disassembling the internal components like planet carriers, gears, shafts, and seals. Reassembly involves heating bearings, installing seals and bearings using presses and tools, and reattaching the final drives to the frame. Precautions are noted to prevent damage to seals during axle removal and installation.
This document provides instructions for servicing the final drives on a D7H track-type tractor. It describes how to remove and disassemble the final drives, including removing the planet carriers, gears, shafts and other components. It then describes how to assemble the final drives, including installing bearings, seals, rings and other parts back into the hubs and carriers. The goal is to provide maintenance technicians with step-by-step directions for servicing these critical components.
1) The document provides instructions for removing and installing pistons, connecting rods, connecting rod bearings, and crankshaft main bearings for a Caterpillar 3306 engine.
2) The procedure involves using tools to compress piston rings, installing pistons and connecting rods onto the crankshaft, checking clearances of connecting rod bearings, and removing/installing main bearing caps.
3) Technicians are advised to keep all parts clean and lubricated with engine oil to prevent damage and wear.
The document provides instructions for removing final drive cases, gears, idler pinions and bearings from a D7G track-type tractor. The steps include:
1) Removing bolts holding the final drive case in position.
2) Installing guide bolts and forcing screws to separate the final drive case from the steering clutch case.
3) Using wire to hold the idler pinion in place so the planet carrier does not fall when the final drive case is removed.
The document provides step-by-step instructions for removing and installing sprocket assemblies on a final drive case. It involves draining the oil, removing the sprocket and various components using specialized tools, cleaning seals and surfaces, and installing the new sprocket along with bearings, seals, and other parts in reverse order. Precise measurements and torque specifications are listed to ensure proper installation.
The document provides instructions for removing and installing sprocket assemblies on a direct drive final drive. The key steps include:
1. Draining the oil and removing the sprocket, holder assembly, seals, bearings and other components.
2. Cleaning surfaces and installing new seals before pressing the sprocket onto the hub using a hydraulic press.
3. Reassembling the holder assembly by installing bearings, seals, and adjusting nut then attaching it to the sprocket shaft.
This document provides instructions for removing and installing the engine in a D7F track-type tractor model 94N. The removal process involves draining fluids, disconnecting wiring harnesses and fluid lines, and removing mounting hardware. The engine can then be lifted out of the tractor body. Installation is the reverse of removal, reconnecting all fluid lines, wiring, and securing the engine with mounting hardware. Proper lubrication and adjustment of components is also specified.
This document provides instructions for removing and installing various components of a D7F track-type tractor engine. The components include the timing gear cover, camshaft, flywheel, crankshaft rear seal, power take-off drive gears and bearings, and removing the entire engine. Detailed steps are provided for each component, including preparatory steps, individual installation and removal steps, and concluding steps.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i06750397
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7241 Valve Spring Compressor 1
B 441-0714 Tool As 1
Start By:
a. Remove the electronic unit injectors.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Place the piston at the top of the compression stroke (TC). Remove the valve springs for
that cylinder. If the valves fall into the cylinder liner, then the cylinder head must be removed.
1. Position the No. 1 piston at the top center of the compression stroke. Refer to Testing and
Adjusting, "Finding Top Center Position for No. 1 Piston".
1/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g01073852
Illustration 2 g01043625
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 2. Install Tooling (A) in the electronic unit injector sleeve. Secure Tooling (A) with unit
injector clamp (1).
3. Tighten the full nut until valve spring keepers (3) are loose on valve (2).
4. Remove valve spring keepers (3) from the valve.
5. Carefully remove Tooling (A).
6. Remove valve rotator (4).
7. Remove outer valve spring (6) and inner valve spring (5) from the valve.
8. Remove washer (7) from the valve guide.
9. Use Tooling (B) to check the valve springs (spring force). Refer to Specifications, "Cylinder
Head Valves" for additional information on the valve springs.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-7241 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Lubricate the valve stems with clean engine oil.
3/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 3 g01043625
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Ensure that washer (7) is installed on the valve guide.
3. Install inner valve spring (5) and outer valve spring (6) on valve (2).
4. Install valve rotator (4) on valve (2).
The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
5. Use Tooling (A) to compress inner valve spring (5) and outer valve spring (6). Install valve
spring keepers (3) on valve (2). Remove unit injector clamp (1) and Tooling (A).
4/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. End By:
a. Install the electronic unit injectors.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 13 22:48:14 UTC+0800 2020
5/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i06750410
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
B 441-0714 Tool As 1
Start By:
a. Remove the cylinder head.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g01015263
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Install Tooling (A) and compress the valve springs. Remove valve spring keepers (2) from
valve (1).
2/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 2. Carefully remove Tooling (A) from valve (1).
3. Remove valve rotator (3).
4. Remove outer valve spring (5) and inner valve spring (4) from valve (1).
5. Remove washer (6) and valve (1) from the valve guide.
6. Use Tooling (B) to check the valve springs (spring force). Refer to Specifications, "Cylinder
Head Valves" for additional information on the valve springs.
7. Inspect the valves. Refer to Specifications, "Cylinder Head Valves" for additional
information on the inlet and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: A small amount of grease can be used to hold the retainer locks in position during
installation.
1. Lubricate the valves with clean engine oil. Install the valves in the cylinder head.
3/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 2 g01015263
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install washer (6) on the valve guide.
3. Install inner valve spring (4) and outer valve spring (5) on valve (1).
4. Install valve rotator (3) on valve (1).
4/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 5. Use Tooling (A) to compress inner valve spring (4) and outer valve spring (5). Install valve
spring keepers (2) on valve (1).
The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
6. Carefully remove Tooling (A).
End By:
a. Install the cylinder head.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 13 22:49:10 UTC+0800 2020
5/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i05887270
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6895 Valve Guide Driver 1
(1)
Part of 9U-7530 Engine Tool Group
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 1 g01073841
1. Remove valve stem seal (1) from valve guide (2).
2. Use Tooling (A) and a hammer to remove the valve guide from the cylinder head.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6895 Valve Guide Driver 1
B(1)
9U-6894 Guide Collar 1
C(2)
455-0128 Seal Installer 1
375-2773 Seal Installer 1
(1)
Part of 9U-7530 Engine Tool Group
(2)
Use Seal Installer 455-0128 with Seal 163-2478. Use Seal Installer 375-2773 with Seal 361-3926
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 2 g01073842
1. Lubricate the bores for the valve guides with clean engine oil.
2. Install valve guide (2) in the cylinder head with Tooling (A) and Tooling (B).
Note: Tooling (B) must be used in order to install the valve guide to the correct height.
Height to top of valve guide from cylinder head surface ... 35.00 ± 0.50 mm
(1.378 ± 0.020 inch)
Note: For more information, refer to Specifications, "Cylinder Head Valves".
3. Use Tooling (C) to install valve stem seal (1) on the valve guide.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 13 22:50:05 UTC+0800 2020
3/3(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i04947937
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 166-7441 Valve Seat Extractor Tool Group 1
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 1 g01145463
1. Use Tooling (A) to remove valve seat insert (1) from the cylinder head.
2. Clean the bores in the cylinder head for the valve seat inserts. Remove any rough areas from
the bores.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B(1)
9U-6898 Valve Seat Driver (Exhaust) 1
9U-6897 Valve Seat Driver (Inlet) 1
(1)
Part of 9U-7530 Engine Tool Group
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 2 g01079028
1. Lower the temperature of new valve seat insert (1).
2. Use Tooling (B) to install the new valve seat insert in the cylinder head.
Note: Do not machine the prefinished valve seat inserts in order to correct the valve stem
projection. An excessive valve stem projection indicates that the valve seat insert is not
seated or material was not cleaned from the bottom of the counterbore.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 13 22:51:01 UTC+0800 2020
3/3(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i04085349
Engine Oil Filter Base - Remove and Install
SMCS - 1306-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Illustration 1 g02294113
1. Use Tooling (A) to remove engine oil filters (4).
2. Remove bracket (3)
3. Remove bolts (1) and remove the engine oil filter base (2).
1/2(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 2 g02294238
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
4. Remove cover (5), gasket (6), springs (7) and plungers (8) from oil filter base (2).
Installation Procedure
1. Install the engine oil filter base (2) in the reverse order.
a. Apply clean engine oil to the oil filter seals prior to installation. Install the engine oil
filters until the oil filter seal contacts the base, then turn the engine oil filters one full
turn.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 13 22:51:57 UTC+0800 2020
2/2(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i04158087
Engine Oil Cooler - Remove and Install
SMCS - 1378-010
Removal Procedure
Start By:
a. Remove the exhaust cooler (NRS).
b. Remove the engine oil filter base.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. 1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Illustration 1 g02352422
Note: Ensure that engine oil cooler core (1) does not fall when bonnet (2) is removed.
2. Remove bolts (3), bonnet (2), and the gasket.
Illustration 2 g02352423
3. Slide engine oil cooler core (1) and bypass tube assembly (4) toward the front of the engine
and remove engine oil cooler core (1) and bypass tube assembly (4).
4. If necessary, remove bolts (5), bonnet (6), and the gasket.
Installation Procedure
1. Install engine oil cooler core (1) in reverse order of removal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 13 22:52:53 UTC+0800 2020
2/2(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i02288785
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Disconnect the tube assemblies from the engine oil pump.
1/2(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 1 g01145746
2. Remove bolts (1) and engine oil pump (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 13 22:53:48 UTC+0800 2020
2/2(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i02289189
Engine Oil Pump - Disassemble
SMCS - 1304-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 1P-2320 Puller Assembly 1
Start By:
a. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 1 g01145905
1. Remove bolt (5), thrust plate (6), and idler gear assembly (7) from shaft assembly (8).
2. Use Tooling (A) and a suitable press in order to remove the bearing from idler gear
assembly (7).
3. Remove shaft assembly (8) from body (4). Remove bolt (1) and washer (2).
4. Use Tooling (A) and Tooling (B) to remove drive gear (3) from body (4). Remove the key
from the pump shaft.
2/4(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. Illustration 2 g01145925
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
5. Remove bolts (9) and separate body (10) from spacer (12) and body (4).
6. Use Tooling (A) and a suitable press in order to remove the bearings from body (10).
7. Remove gears (11). Remove spacer (12).
8. Remove the bearings from spacer (12).
9. Remove shaft assemblies (13).
10. Remove bolts (14) and retainer (15).
3/4(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...