Recommended
More Related Content
What's hot
What's hot (18)
Viewers also liked
Similar to Current Transformers: Ratio & Burden Testing
Similar to Current Transformers: Ratio & Burden Testing (20)
Recently uploaded
Recently uploaded (20)
Current Transformers: Ratio & Burden Testing
- 1. 1 10/02/2012 Slide 1 Current Transformers: Ratio and Burden Testing Prepared by Rob Reese,TESCO For the Heartland Metermans Conference - March 31, 2014
- 2. 2 Self Contained vs. Transformer Rated 1S, 2S, 3S, 4S, 9S, 12S, 16S, 45S, etc., etc. What’s the Difference? Different Forms for Different Services and Applications
- 3. 3 Self Contained vs. Transformer Rated Self Contained (direct) Transformer Rated (indirect)
- 4. 4 Self Contained Primarily Residential (1S, 2S, 12S) Relatively Low Current Example: 100A
- 5. 5 Transformer Rated Primarily Commercial/Industrial (9S, 16S) Relatively High Current Example: 400A
- 6. 6 Transformer Rated Primarily Commercial/Industrial (9S, 16S) Relatively High Current Example: 400A 400:5 5A
- 7. 7 CT’s – Functions and Terminology Ratio Equivalent Circuit w/ losses Conceptual Picture of a CT As current is applied in the primary, it produces a magnetic flux in the core. This flux flows through the core and induces a current in the secondary windings and circuit that is proportional to the number of turns.
- 8. 8 CT’s – Functions and Terminology Ratio For instance, a CT with a 400:5 ratio will produce 5A on the secondary, when 400A are applied to the primary.
- 9. 9 CT’s – Functions and Terminology Thermal Rating factor A value representing the amount by which the primary current can be increased without exceeding the allowable temperature rise. For instance, a RF of 4.0 at 30 ambient on a 400:5 ratio CT would allow for a primary current up to 1600A.
- 10. 10 CT’s – Functions and Terminology Accuracy Classifications and Burden All CT’s fall within an accuracy class. IEEE Standards have defined accuracy classes.
- 11. 11 CT’s – Functions and Terminology Accuracy Classifications and Burden Example: 0.3% @ B0.1, B0.2, B0.5
- 12. 12 CT’s – Functions and Terminology Faceplate
- 13. 13 Transformer Rated 9S Meter Installation 5A PHASE A SOURCE PHASE C PHASE B LOAD 400A 400A 400A 5A5A
- 14. 14 Transformer Rated 9S Meter Installation 5A PHASE A SOURCE PHASE C PHASE B LOAD 400A 400A 400A 5A5A
- 15. 15 Meter Testing 9S Meter Installation 5A PHASE A SOURCE PHASE C PHASE B LOAD 400A 400A 400A 5A5A Isolate the Meter from the Service P
- 16. 16 Meter Testing 9S Meter Installation 5A PHASE A SOURCE PHASE C PHASE B LOAD 400A 400A 400A 5A5A ? ? ?
- 17. 17 Meter Testing 9S Meter Installation 5A PHASE A SOURCE PHASE C PHASE B LOAD 400A 400A 400A 5A5A What if? 355:5 405:5 200:5 Shorted etc.
- 18. 18 CT Testing CT Testing is Important! 1) Test for correct ratio 2) Test for functionality at rated burdens
- 19. 19 Ratio Testing Ratio of Primary Current to Secondary Current 5A PHASE A SOURCE LOAD 400A 400A 400A 5A5A Calculate Ratio
- 20. 20 Burden Testing Functionality with Burden Present on the Secondary Loop PHASE A Some burden will always be present – junctions, meter coils, test switches, cables, etc. CT’s must be able to maintain an accurate ratio with burden on the secondary.
- 21. 21 Burden Testing Functionality with Burden Present on the Secondary Loop PHASE A Some burden will always be present – junctions, meter coils, test switches, cables, etc. CT’s must be able to maintain an accurate ratio with burden on the secondary.
- 22. 22 Burden Testing Functionality with Burden Present on the Secondary Loop Example Burden Spec: 0.3% @ B0.1, B0.2, B0.5 or There should be less than the 0.3% change in secondary current from initial (“0” burden) reading, when up to 0.5Ohms of burden is applied
- 23. 23 Burden Testing Functionality with Burden Present on the Secondary Loop ANSI Burden Values 0.1 Ohms 0.2 Ohms 0.5 Ohms 1 Ohms 2 Ohms 4 Ohms 8 Ohms
- 24. 24 Burden Testing 0.0000 1.0000 2.0000 3.0000 4.0000 5.0000 6.0000 0 2 4 6 8 0.3% @ B0.1, B0.2, B0.5 Initial Reading = 5Amps 0.3% x 5A = 0.015A 5A – 0.015 = 4.985A Burden Reading 0 5.0000 0.1 4.9999 0.2 4.9950 0.5 4.9900 1 4.9800 2 4.9500 4 4.0000 8 0.8000
- 25. 25 Burden Testing 4.9500 4.9600 4.9700 4.9800 4.9900 5.0000 5.0100 5.0200 5.0300 5.0400 5.0500 0 0.2 0.4 0.6 0.8 1 0.3% @ B0.1, B0.2, B0.5 Initial Reading = 5Amps 0.3% x 5A = 0.015A 5A – 0.015 = 4.985A At 0.5Ohms of Burden the secondary current is still at 4.990A – Less than 0.3% change – Good CT! Burden Reading 0 5.0000 0.1 4.9999 0.2 4.9950 0.5 4.9900 1 4.9800 2 4.9500 4 4.0000 8 0.8000
- 26. 26 Analog Testing Application of Burden and Calculation Manual reading of initial and post- burden secondary currents
- 27. 27 Digital Testing Application of Burden and Calculation Reads the initial current immediately prior to applying the selected burden Applies the selected burden to the secondary Reads the current immediately following current application Calculates the percentages change
- 28. 28 Questions? Please feel free to call or e-mail any questions Rob Reese Rob.Reese@TescoMeterManager.com 215-310-8809 (cell) The Eastern Specialty Company