HENAN BEYNOST TEXTILE TECHNOLOGY CO., LTD.

www.benost.com
HENAN BEYNOST TEXTILE
TECHNOLOGY CO., LTD.

• Main business As a leading global manufacturer and
developer of textile products， and complete
raw material global supply chain system，
Benost offers a wide range of mesh and
solutation for processes and applications ,
Customers all over the world use our mesh
and customized solutions to dewater, press,
filter, separate, forming, dry, cool or freeze
products , the forming fabrics could match to
0-2000m/min line, covering papermaking and
nonwovens, Our world-class technology and
experienced Applications Engineering teams,
help our customers improve their performance
and productivity by innovative forming fabrics,
dryering fabrics， filter belts, we would
continues develop and provide solutions to
optimize the performance of paper making
production, and reduce cost.
www.benost.com

How to solve wire mark paper disease？
1.By adjusting the lip orifice in the direction of the weir plate, reduce the leakage of the chest roller. If possible,
change the bending of the lip of the weir plate to make the extruded slurry fall further away from the forming
network.
2.For dehydration slow slurry, reduce the fine grinding.
3.Gradually increase the vacuum of the vacuum box and use all vacuum boxes
4.If the forming fabricis too loose, increase the tension of the net.
5.Increase the slurry concentration.
6.Reduces dam board, dewatering elements and vacuum boxes.
7.Adjust as necessary: raise the position of watermark roller; Reduce press roll load; Study the possibility of using
high mesh forming fabric; Sometimes the screen printing is related to the depth of the penetration forming network.
8.Excessive dehydration without turbulence may cause the wet paper to seal, which will lead to higher vacuum
chamber vacuum and pull the paper to the formingfabric.
9.Use a lower jet Angle.
10.Excessive dehydration during initial molding will cause the ends of the fibers to stand upright and be inserted
into the forming
11.We will have more satisfactory solutions for the filth network problems.
www.benost.com

How to use polyester dryer fabrics.
1.Application：
Polyester dryer fabric is made of polyester monofilament weaving material, which is mainly used for drying paper products on paper machine.
Polyester dryer fabrics according to the organization can be divided into plain dry net and pressure dry net.;according to the way of the joint is divided into two kinds of end
joints and endless joints。
2.Characteristic：
2.1.The service life is more than three times that of canvas and dry carpet.
2.2.High strength, good toughness, abrasion resistance, corrosion resistance and stable dimension.
2.3.Smooth surface and good air permeability
2.4.Light weight, convenient transportation.
3.Method of use：
3.1.The original paper machines using canvas and dry blankets can use polyester webs without modification. If conditions are available, change the original score roller to
flat roller and remove the original blanket cylinder.
3.2.The endless dry web is ring-shaped. Before the machine is starting up, the inner guide roller is first unloaded, the dry web is pulled open along the use position, the inner
guide roller is installed, and the tension of the web is adjusted to 2-3 kg/cm2. Can start running。
3.3.The ends of the net are banded, and the ends of the net are connected by a spiral ring. When it is on the machine, it is introduced from one side. When the two ends of
the head are connected, the connection line is penetrated from one side to the other side. When it is difficult to penetrate once, it can be segmented, but the connection line
must not be cut off. Both ends of the cable must be snapped into the connector to prevent it from coming out.
4.Dry network repair, washing and precautions：
4.1.The two sides of dry net have two kinds of bonding methods:coating adhesive bonding and hot melt bonding.In the process of use, if the divergence phenomenon occurs,
the loose end of the line can be cut off, and then the electric soldering iron can be fused to bond.
4.2.Nets can be sutured when they are in use due to a hard wound or other conditions that result in small holes, partial breakages, etc.
4.3.In the course of use, when a small hole, a partial break, etc. are caused by a fold, stitches can be sewn with thread.
4.4.When shutting down due to power outage or other reasons, immediately shut off the gas valve and relax the net to prevent local deformation and aging.
4.5.When there is local grease on the mesh surface, it can be scrubbed with gasoline or detergent and then rinsed with water.
4.6.In transportation, storage, installation, overhaul and operation, it should be kept away from open flame and high temperature to prevent dry network burning, aging, and
to prevent friction with sharp objects, so as not to scratch the net body and reduce the service life.
www.benost.com

About polyester forming fabric
1.Features
1.1 Long life, wear resistance, low consumption
1.2 High fatigue strength, acid resistance, weak alkali resistance
1.3 Light traces, good molding quality
1.4 Lightweight, easy to transport, easy to use
2.Selection
2.1 Type: It should be based on the use of plant equipment, processes, paper types, pulp and other conditions to choose the
appropriate type
2.2 Length: 0.5% elongation of the polyester forming fabric during use. When selecting the length, the shortest dimension that
can be installed on the machine should be taken.
3.Installation
3.1 Before installing the mesh belt, check whether the equipment is in good condition.The parts that come in contact with the net
are forbidden from unevenness, slanting, sharp hairs, sand, etc. The guide system must be flexible.
3.2 The direction of operation must be in accordance with the direction of the arrow on the mesh belt, place the mesh belt in the
correct position, and the rollers are parallel to each other to prevent the nets from being deflected.
3.3 There should be a swinging high pressure water device that flushes the mesh belt. Medium and low speed paper machine
water pressure is not less than 6-10kg/cm2, speed exceeds 350m/min, water pressure is not less than 10-15kg/cm2, when using
multi-layer forming nets, water pressure requirements 15-30kg/cm2. Water should be clean and without sand.
3.4 When installing the mesh belt, first slightly tension the net, add water to lubricate and run. After the sizing, pay attention to
adjust the tension of the net to the normal level, the tension of the low speed paper machine is kept at 3-4kg/cm2, and the
tension of the medium and high speed paper is kept at 4-6kg/cm2.
www.benost.com

4.Using
4.1 At the beginning of operation, natural elongation will occur. During the first 1-2 days of operation, we must pay attention to
adjust the tension of the mesh at any time to reach the standard, maintain the tension, and stabilize the mesh after 3 days of
operation.
4.2 In the process of use, it is necessary to use high pressure water spray and clean the net in time, and turn off the high-
pressure water in time when shutting down, so as not to damage the mesh.
4.3 When large area flushing, use 5% alkaline solution or 10% acidic solution, wash with a soft-bristle or nylon brush, and wash
with water after washing.
4.4 When the machine is shut down for a long time, the mesh belt must be relaxed, and the suction system must be stopped. If
you need to repair the paper machine in the middle of use, you should carefully retreat the mesh belt. When installing the mesh
belt, it must be installed according to the original running direction.
5.Storage
5.1 Polyester mesh is made of high molecular organic material and should be stored in a dry environment at room temperature,
avoid high temperature and humidity.In order to avoid mesh deformation, storage time should not be too long.
5.2 When the storage temperature is too high or too low, it should be stored in the production workshop for two to three days
prior to use to avoid length dimensional changes.
6.Precautions
6.1 When installing or removing, it is necessary to properly protect the mesh, and avoid creases caused by mesh belt damage
and extrusion.
6.2 The mesh is strictly prohibited from dry grinding, or ditch or slip due to inappropriate tension.
6.3 The mesh is strictly prohibited from turning over, otherwise it will wear out quickly.
6.4 Do not flush the mesh with high temperature steam or brush with a metal brush.
6.5 Fireworks and high temperatures are strictly prohibited.
www.benost.com

Problems and Causes of Problems during the Use of
Papermaking Machinery Forming Fabric
1.Mesh belt edge wear too fast:The vast majority of paper-making machinery is worn out at the joints with vacuum and no
vacuum (10-15cm mesh edge).
Solution:1.1.Try to increase the width of the vacuum box opening.
1.2.Add atmospheric lubrication water to the edge of the real empty box.
1.3.Add a reinforcing rib to the appropriate position.
1.4.Check whether there are edges or gaps in the side wiper and the real empty box. In particular, the joints of the ceramic
panels are weak.
1.5.Check whether there is serious wear on the edges of the rolls(After the roller wear, the diameter of the roll becomes smaller
and the tension of the net is smaller than that of normal mesh, which further accelerates the wear.).
2.Overall wear:
2.1.The quality of the panel is unqualified.
2.2.The tension of the net is small, and the backhaul tension of the single-layer fabric is 3-4kg/cm, and the backhaul tension of
the forming fabric is 5-6kg/cm.
2.3.Poor pulp quality.
2.4.The high air pereability of mesh causes the loss of pulp, and there are too many filler particles between the mesh and the
real empty box panel, which will also speed up the overall wear of the mesh.
2.5.The low permeability of the mesh allows the vacuum to increase and the wear is accelerated.
2.6.The roller speed and the mesh speed are out of sync.
2.7.The speed of the mesh is not synchronized.
www.benost.com

3.Local wear out too quickly:
whether the molding board, wiper board, vacuum box panel has the wrong stubble, uneven and the gap;
whether the rolls have local wear and corrosion.
4.Local bulge:
whether the molding board, wiper board, vacuum box panel has the wrong stubble, uneven and the gap;
chest roll vacuum roller whether there are solder joints and other protrusions, whether the rubber roller has impurities.
5.Guide roll wrapped slurry:
the cleaning water pressure is low, the mesh internal fiber is much;
the mesh air pereability is low;
there is a problem with the cleaning method. The two and half nets should clean the paper surface of the net, the nozzle is
blocked, and the best distance between the nozzle and the net is 15-20cm.
6.The pulp in the vacuum box is too full:
Insufficient air permeability;
Short pulp fiber causes a lot of loss;
The retention agent has poor quality or little addition.
7.The mesh belt runs with a wide range of movement: The corrector is not working properly and the mesh is not straight.
8.The net becomes narrow after being used for a period of time:After running for a period of time, the line deflection (the local
network operation is inconsistent) is due to the local wear of the molding board, the wiper board, the real empty box panel or the
guide roller.
9.The comparison between the type D and the life of the previous mesh:D-type can effectively solve the two sides different of the
paper, accelerate the dehydration and improve the speed, but the life of the forming fabric will decrease, the main reason is that
the waterline is shortened and the wear speed is accelerated. Life expectancy is down by a third or even a half.
www.benost.com

Filter cloth deviation problem
Filter cloth deviation is a common problem of vacuum belt conveyor.The general belt conveyor will have a filter cloth deviation
warning device and automatic correction device.Automatic corrective device is generally electric or pneumatic.Here we talk
about pneumatic automatic correction device.
The pneumatic correcting device is composed of a sensor, an air source distributor and an adjusting airbag.When the filter
cloth is deflected, the gas distributor will distribute compressed air to the two regulating bags according to the direction of the
filter cloth, and then adjust the Angle of the roller to correct the direction of the filter cloth.Under normal circumstances, the
adjusted corrective device can ensure that the filter cloth automatically corrects.It should be noted here that the position and
angle of the sensor need to be adjusted during running in idle, water loading and load operation.If the deviation correcting
device is adjusted only during idling or when adding water empty load operation, the phenomenon of filter cloth deviation will
occur. At this time, there is no need to stop, and only the correction device can be adjusted again.It is worth noting that before
the upper filter cloth, all the filter cloth support rollers should be checked again to prevent the displacement of the filter cloth
support roller due to transportation or other reasons.It is very important to ensure that the filter roller is parallel.
As for the phenomenon of deviation of the filter cloth, there are mainly two reasons for the filter cloth itself:
1. Unscientific weaving process results in non-uniform quality of the filter cloth. When it is subjected to strong pulling force
during operation, it will tend to the large-quality side.
2. Inaccurate cutting during the cutting of the filter cloth causes the filter cloth not to be a standard rectangle but a trapezoid,
so that the deviation of the filter cloth will often occur after a period of time.
www.benost.com

PAPER MACHINE CLOTHING
The paper machine clothing(PMC) is customized
fabrics and belt, usually used in entire paper and
board machine for paper forming, dewatering,
drying,and transport the paper sheet through
paper machine, as a leader of textile
technology,Benost offers high quality fabrics and
belts for entire pulp, paper, board and tissue
making line to improve paper making process
performance,Benost continue develop new
design fabrics and belt for paper making
industries to reduce production operation cost,
our fabrics and belts usually serve: kraft
paper,Newsprint, Testliner ,Corrugator ,wrapping
paper, tissue paper, cultural paper, and so on
paper mill.
www.benost.com

Single layer forming fabrics
Description
The single layer forming fabrics is the simplest forming net, It
includes four different forms:
1. 2-shed (one up and one down) : The design is mainly used in
sewage treatment plants, sludge dewatering machines, etc.
2. 3-shed (one up two down): Mainly used for sludge dewatering
machine, washing machine and bleaching machine.
3. 4-shed (one up and three down) : Mainly used for various
paper machines.
4. 5-shed (one up and four down) : Mainly used to produce all
kinds of kraft paper, tissue paper, writing paper, printing paper,
etc.
Benefits:
1.Simple structure of single layer forming network, good
dewatering and good air permeability.
2.Excellent formation and excellent fiber support.
3.No fabric marking and easy to clean.
4.Very good stable and wear resistance.
Applications:
1. Pulping, pulp washers.
2. Sludge dewatering, black liquor extraction.
3. Writing papers, printing papers, kraft papers, newsprint
papers,straw boards,tissue papers.
www.benost.com

1.5 Layer forming fabric
Description
The 10-shed 1.5 layer forming fabric has stronger
dewatering performance and secondary Fiber Recycling
and Straw Pulping Application for papermaking long
paper machine or long wire paper machine with a
weight of between 50-220g to reduce paper machine
wear.
Benefits：
1.Stronger dewatering performance, long life.
Application ：
1.Newsprint.
2.Writing paper.
3.Printing paper.
4.Kraft paper.
5.Corrugated paper.
6.Tissue paper
www.benost.com

Double layer forming fabric
Description
With the increase in the speed of the paper machine
and the increase in the width of the forming fabric, the
double-layer forming fabric is indeed an overhead.
Benefits：
1.High dimensional stability, unique weaving structure
can resist longitudinal load and horizontal wrinkling.
Application ：
1.Paperboard.
2.Newsprint,writing paper.
3.Tissue paper.
4.printing paper,kraft paper
www.benost.com

2.5 Layer forming fabric
Description
The 8-shed 2.5 layer net is the most common 2.5 layer
forming fabric. Its weaving effect greatly increases the
fiber support index due to the addition of a fine weave
at the top. The ratio of the top and bottom wefts is 2:1.
The 8-shed above and 16-shed below weaving
technology, its performance greatly improves the
surface smoothness and higher paper support effect.
Benefits：
1.Good top layer smoothness;
2.Excellent formation and excellent fiber support;
3.No fabric marking and easy to clean;
4.Very good stable and wear resistance;
5.Good paper threading and retention.
Application ：
1.Paperboard.
3.Tissue paper.
4.printing paper,kraft paper.
www.benost.com

Triple layer forming fabrics
Description
An important advantage of our three layer forming
fabrics is low warp density,another anvantage of this
types: the weft wire of the wear surface spans a lot, that
could gives the forming fabrics a long life postential,the
weft span would be 8 warp rather than common 6 or 5
warp, choosing the best forming fabrics type will save
many costs in terms of clean operation, additive use,
and vacuum, water, and electricity consumption.
Benefits：
1.For paper and board grades that require excellent
printability.
Application ：
1.Cigarette tissue,cigarette finer tissue,copy
tissue,LC,LWC.
2.Newsprint,writing paper,carbonless paper,copper
print.
3.Tissue napkin,tolite tissue.
4.Top or liner side for kraft and card board.
www.benost.com

Spiral Dryer Fabrics
Description
Dryer fabric is spiral type,its special design is entirely designed to
improve the drying efficiency, with circular and flat water
resistance woven technology, inlet air can be effectively
controlled so that it can meet the dry parts at all levels.
Mainly used in the dry nozzle area of the paper machine, easy to
operate, the appropriate thickness to improve the life efficiency
of good drying efficiency air permeability range: 700-1000 CFM
(widely used in the production of glossy kraft paper and
imitation paper)
Benefits
1.Full monofilament structure, with anti-pollution, anti-hydrolysis.
2.Keep clean and dry.
3.Good heat transfer, no traces.
4.Stable and better wear resistance.
5.Long life, easy to clean.
6.100% high strength anti-hydrolysis monofilament.
7.66% of PPS monofilaments 18-25 cm.
8.PEEK spiral ring interface: No net marks, high strength, easy to
install.
Application ：
1.Paperboard.
3.printing paper,kraft paper.
4.Carbonless paper,copper print.

Woven Dryer Fabrics
Description
Flat dry webs are woven from warp threads and weft threads, warp
and weft threads are used for hydrolysis-resistant polyester materials,
the meridian includes the top and bottom warp, the two meridians
are one group, and are woven through two sets of four meridians
with two different diameters, the warp threads are flat filaments and
the weft is round wire, the section size of the flat wire meridian is
0.32mm x 0.80mm, the diameters of the two different sections of the
circular filaments are 0.40mm, 0.60mm or 0.70mm.
Benefits
1.Full monofilament structure, with anti-pollution, anti-hydrolysis
2.Keep clean and dry
3.Good heat transfer, no traces
4.Stable and better wear resistance
5.Long life, easy to clean
6.100% high strength anti-hydrolysis monofilament
7.66% of PPS monofilaments 18-25 cm
8.PEEK spiral ring interface: No net marks, high strength, easy to
install
Application ：
1.Newsprint.Corrugated paper.Cultural paper.
2.Tissue paper.Packing paper.Toilet paper.
3.Kraft paper.Testliner.
4.Paperboard.
www.benost.com

FILTER BELT
The paper machine clothing(PMC) is customized
fabrics and belt, usually used in entire paper and
board machine for paper forming, dewatering,
drying,and transport the paper sheet through
paper machine, as a leader of textile
technology,Benost offers high quality fabrics and
belts for entire pulp, paper, board and tissue
making line to improve paper making process
performance,Benost continue develop new
design fabrics and belt for paper making
industries to reduce production operation cost,
our fabrics and belts usually serve: kraft
paper,Newsprint, Testliner ,Corrugator ,wrapping
paper, tissue paper, cultural paper, and so on
paper mill.
www.benost.com

• Mining filter fabrics
Benost filter belts usually used for mining industry to filtering and separating, the screen belts made of
polyester or metal, with the optimum mesh openings, guarantee the high separation efficiency and filtration
performance.
www.benost.com

Desulfurization filter fabrics Description
Used for: series of rubber belt vacuum filter, horizontal vacuum belt filter, vacuum drum filter,
vertical filter press, etc.
It is applicable to solid-liquid separation industries such as wet desulfurization of power
plants, tailings, metallurgy, mining, chemical industry, coal chemical industry, papermaking,
food, pharmaceuticals and environmental protection.
Benefits：
1.When the filter belt is used at a safe temperature and subjected to a certain pulling force,
the shape of the filter belt is stable.
2.Good chemical stability: use different materials to meet the requirements of harsh working
conditions.
3.The filter belt has high tensile strength and good wear resistance, which makes the product
have a longer service life.
4.Can meet different filtration accuracy requirements (2-100μm).
5.The stripping performance of the filter belt is good, and it is easy to regenerate.
6.The use of high-quality materials and advanced technology makes the joint strength of the
mesh belt high, so the product has a long service life.
7.Good wear resistance, good acid and alkali corrosion resistance, thickness more than
1.6mm, greatly enhance the service life of the filter cloth.
Application:
1.Sludge dewatering: It is widely used in the sewage sludge treatment plant, power plant,
steel plant, papermaking, mining, metallurgy, petroleum and other industries.
2.Power plant desulphurization: It is widely used in limestone-gypsum dehydration in wet
desulfurization with horizontal vacuum belt filter.
3.Process filtration for large-scale industrial production: Compatible with a wide range of
filter types Widely used in filtration of tailings, coal washing, pulp washing, alumina, and
other industries.
www.benost.com

Sludge dewatering fabric
Sludge dewatering fabric of Benost mesh belt mainly used in belt
filter press system, rubber belt vacuum filter, horizontal vacuum
belt filter.
It is suitable for municipal sludge, filter press for sludge in various
industries, paper mill press, juice concentrate press and other
special industries.
Description
Sludge dewatering fabric details description
Benefits:
1.The best product structure and release, the mesh belt is a
herringbone design, sludge and mesh belt stripping fast, not easy
to slime, easy to clean0.
2.Good operational stability even at high speeds.
3.Effective particle retention.
4.Apply optimized breathability.
5.High lateral stability and high mechanical strength.
6.Best throughput performance, high efficiency, large throughput.
7.Multi-zone dehydration, strong dewatering capacity, low
moisture content of sludge cake.
www.benost.com

NONWOVEN MESH BELT
Benost offers a range of conveyor mesh belts for
nonwoven fabrics manufacturer, using innovative
technologies and engineers teams provides
optimum belts for every line configuration in
every global market, suitable for Spunbond /
Meltblown, Spunlace, Hot air, Airlaid, Wetlaid
nonwoven production line in forming and
transport application, the belts made of PET or
metal material, quality stable, anti-hydrolysis,
anti-pollution, customized seam joints according
to belt types, that ensure the belt work high
performance, Benost continuous improvement
and innovative mesh belts are focused on
helping our customers reduce operating cost,
improve product quality.
www.benost.com

• Airlaid mesh belt
In airlaid dust-free paper applications, Benost designed the mesh belt with improved belt quality and anti-
pollution properties from wood pulp air flow molding, sizing drying and other aspects, and the design of
different areas of the air permeability parameters are different, the network edge processing method is also
based on the difference in the customer’s production process, and the intensity of processing is more stable,
the use of a power grid overcomes the occurrence of product cloud spots, and the web builds more evenly.
www.benost.com

Meltblown mesh belt
According to the characteristics of the melt-blown industry, meltblown mesh belt play a key role in the
formation of fabric, high-permeability circular weaving and effective discharge of static electricity allow
extruded and disentangled fibers to be distributed on the mesh belt, mesh belt is not afraid of high
temperature solution spray, and have strong peelability, plaques are easy to clean.

Hot air mesh belt
Benost has designed high-speed carding mesh belt and heat-bonded mesh curtains with strong anti-stick
properties for hot air mesh belt, and providing the necessary conditions for increasing the speed of the
production line. The special design of the net curtain makes inlet diversion, smooth suction, and the hot wind
build-up penetration effect is good, which effectively improves the thermal energy utilization rate and reduces
the energy consumption. The ES fiber was evenly laid on the web and peeled quickly.
www.benost.com

Spunbond mesh belt
Spunbond non woven mesh belt also called conveyor or forming belt,the belt
made of polyester monofilament, there are three types belt, round filber belt,
flat filber belt, and anti-static conveyor belt, air permeability: 500-2000 cfm,
different line speed will match to different air permeabilty belt, high technical
designed for high-speed machine, customized any high air permeability and
anti static belt depend on customers request, also provide good solution for
spunbond nonwoven production.
Seam types: self joints, spiral joints, double layer self joints.
Description
The spunbonded nonwoven fabric developed rapidly, with production line
speed of nearly 2000 M/min and fabric weight of 10 g, Benost offers a wide
range of products with a high degree of matching, we are committed to
helping customers reduce operating costs and improve product quality, for
the medical and hygiene industries, the spunbond mesh belt need a flat
interface design, no imprint, and excellent running performance, the smooth
surface of the mesh belt makes the fiber mesh pass smoothly without lint.
Benefits:
1.Belt surface is smooth,
2.PTFE monofilament is used,
3.The equipment is running clean,
4.Double ring interface,
5.Consistent with the mesh surface,
6.Convenient installation,
7.High dimensional stability,
8.Uniform fiber mesh forming.
www.benost.com

Spunlace mesh belt From spunlace nonwoven high-speed carding machine to hot air cylinder or flat
screen drying cadre, Benost provide a series of different performance net curtain
and drum,which can not only match different spunlace equipment but also achieve
the spunlace properties are optimized to produce spunlace nonwovens with
various shapes and unique functions through various Bennite jacquard cylinders or
jacquard screens.
We have PET spunlace conveyor mesh belt,PET and stainless steel spunlace
forming belt,jacquard mesh belt,10-40 mesh spunlace belt, common belt: 22 mesh,
widely suitable for facial mask spunlace nonwoven fabric，wipes spunlace
nonwoven fabric, high technical and good quality get highly valued by customers.
Description
High-performance monofilaments and special nickel are used in the screens and
rollers corresponding to the Spunlace Line, which can produce 12 to 500 grams of
various spunlace nonwovens for sanitary materials, the net curtain and roller used
in the spunlace cross and semi-cross network meet the industrial cleaning and life
wiping, and also apply to filter materials, focusing on innovative applications, we
continue to develop web curtains for different applications based on market
feedback to match the expanding applications of spunlace nonwovens and tailor
your exclusive products to your market protection.
Benefits:
1.Strong dehydration.
2.Double – warp lock structure, vertical high load, transverse crease.
3.Stable operation and long service life.
4.High strength and good toughness.
5.Abrasion resistance, corrosion resistance.
6.Smooth surface and stable dimension.
www.benost.com

ANTI-STATIC FABRICS
Anti-static fabrics are made of polyester
monofilament and conductive wire in warp and
weft,electrostatic charges discharged by
conductive carbon fiber, avoid Static electricity
damage to the products.
The conveyor belts made of anti-static fabrics
usually used in airlaid, spunlaid, wetlaid and
drylaid nonwoven forming technologies.
Antistatic fabrics have a widely application, such
as spunbond, meltblown, card and wetlaid
nonwovens,wood processing (MDF board,
fiberboard).
The black conductive wire would ensure reliable
electrostatic discharge to keep products stable
quality.
www.benost.com

Anti-static spunbond mesh belt
Antistatic mesh belt is widely used in nonwoven, wood, dust-free
paper, chemical fiber and other industries. According to the
different nature of industrial applications, Benost conductive mesh
belts are rich in variety and perfectly match various application
fields. Whether it is an endless interface or an end-to-end
interface, it can accurately achieve dimensional stability and
excellent discharge performance. Mesh belt with high strength,
high mechanical load resistance, able to adapt to strong impact
whether it is pressing, embossing, drying, etc.
Benifits:
1.They don’t hang with the fibers;
2.To produce relatively light non-woven fabrics uniformly
(<100g/m2);
3.High wear resistance, long life;
4.High transverse rigidity, high longitudinal softness, permanent
antistatic;
5.Low tension can operate, save energy, good dissociation;
6.It is suitable for all man-made fibers;
www.benost.com

Anti-static fabrics Paving belt has strong structural stability, easy to correct the characteristics of strong
wear resistance, etc. It effectively prevents the deviation of the belt and improves the
working efficiency. The joint can use steel card joints, spiral ring joints, etc.
Used for : Wood processing, MDF board/OSB/HDF/Partical board making etc.
Description
1.The entry belt must pass through a bovine nose roller (6 mm fine axis) and still
maintain a balanced transport, can be easy to correct, Strong and durable and
resistant to high temperatures. We used a special monofilament. The braided surface
was coated with a special coating and a screw interface (instead of a hot-pressed form)
was used to meet the requirements of the equipment for the mesh belt. The
installation was more convenient and the downtime was shortened. ensures the
continuity, stability and efficiency of modern industrial production.
2.Slab heating belt has good heat dissipation, stability, wear resistance and other
characteristics, so that the slab forming effect is more obvious, using spiral ring, pin
ring interface.
3.The breathable belt adopts a special wear-resistant, anti-pulled wire, which can
adapt to any chemical substances introduced in the wood-based panel industry, so
that the mesh belt has excellent air permeability, and the anti-static black wire makes
the mesh belt have good anti-static and anti-adhesion. The performance can
effectively prevent the fiber from clogging the mesh belt and improve the production
efficiency. The fittings can be selected based on the specific use of the customer by
using the endless, pin ring and spiral ring.
4.Paving belt has strong structural stability, easy to correct the characteristics of
strong wear resistance, etc. It effectively prevents the deviation of the belt and
improves the working efficiency. The joint can use steel card joints, spiral ring joints,
etc.
www.benost.com

Glass fiber felt bulkhead fabrics
Fiberglass mats and AGM separators are uniform and flexible materials in the wet molding process. Benost forming fabric has
designed a series of mesh belts with strong fiber support and high acid resistance properties according to different technical
requirements. The special weaving method enables the separator to have a high porosity and a strong liquid-absorbing ability.
The plain-weave design of the sizing site mesh belt provides good strength, good compression resistance and excellent
elasticity. The corrosion of strong chemicals in the pulping process of AGM separators can be perfectly overcome by our mesh
belts.
www.benost.co

Food industry conveyor mesh belt In the food production process, the food industry conveyor mesh belt
ensures high thermal stability and process reliability when used in a
variety of applications such as baking, cooking, drying, cooling, freezing
or cleaning. To this end, we offer a variety of products – mesh belts made
of plastic, and various metal mesh belts made of stainless steel. The
optimal design of our mesh belt is the basis of these processes, fabric
structures and materials are precisely adapted to these processes.
Description
In the food production process, the food industry conveyor mesh belt
ensures high thermal stability and process reliability when used in a
variety of applications such as baking, cooking, drying, cooling, freezing
or cleaning. To this end, we offer a variety of products – mesh belts made
of plastic, and various metal mesh belts made of stainless steel. The
optimal design of our mesh belt is the basis of these processes, fabric
structures and materials are precisely adapted to these processes.
Benefits:
1.Strong mechanical load capacity.
2.Very high temperature resistance.
3.Chemical resistance.
4.Very good running properties.
5.long life.
www.benost.com

www.benost.com
Thanks for browsing

HENAN BEYNOST TEXTILE TECHNOLOGY CO., LTD.

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Similar to HENAN BEYNOST TEXTILE TECHNOLOGY CO., LTD.

Similar to HENAN BEYNOST TEXTILE TECHNOLOGY CO., LTD. (20)

Recently uploaded

Recently uploaded (20)

HENAN BEYNOST TEXTILE TECHNOLOGY CO., LTD.