The rotation direction of the roller is divided into two types: forward dressing and reverse dressing. Most of them use the forward dressing method (the direction of the linear velocity of the contact point of the grinding wheel is the same); the reverse dressing will be affects the life of the diamond roller...
CNIC Information System with Pakdata Cf In Pakistan
Dressing parameters of diamond rotary dresser
1. MORE SUPERHARD PRODUCTS CO., LIMITED
Address:No. 171 Zhongyuan Rd, Zhongyuan District, Zhengzhou,450000, Henan,,China
Tel/WhatsApp: +86 15617785923 Email: Anna.wang@moresuperhard.com
Dressing parameters of diamond rotary dresser
2020.11.30More Super Hard Products Co., Ltd
1. Linear speed ratio
The rotation direction of the roller is divided into two types: forward dressing and reverse
dressing. Most of them use the forward dressing method (the direction of the linear
velocity of the contact point of the grinding wheel is the same); the reverse dressing will be
affects the life of the diamond roller.
2. Effective surface roughness of grinding wheel Rts
1. The effective surface roughness Rts of the grinding wheel after the roller dressing can
directly affect the production efficiency and surface processing quality.
Generally, as the Rts increases, it means that the grinding wheel is sharp so the
production efficiency increases, and the grinding force is strong and grinding temperature
decreases but the surface finish of the processed workpiece will also decrease, so Rts
achieves a balance in daily production.
2. Factors affecting Rts are:
(1) Diamond size.
(2) Diamond roller dressing amount and line speed ratio.
(3) Vibration during dressing.
2.
3. 3. The relationship between smoothing dressing times NA and Rts
As the number of smoothing dressing increases, the surface of the wheel becomes
smoother.
the smoothing dressing on Rts when the light repair speed is below na 50. But the
smoothing dressing has little effect on Rts when na>50, and it is not recommended that
the number of smoothing dressing>50.
4. The relationship between cutting feed rate ar and Rts
With the increase of the feed per revolution of the grinding wheel, the roughness Rts of
the grinding wheel will also increase, and this increase is more obvious during forward
dressing than during reverse dressing.
However, with the increase in the number of smoothing dressing revolutions, the influence
of the feed rate on the roughness gradually becomes smaller.
4. 5. Vibration of diamond roller
Diamond Roller dressing is the full contact of the entire profile so the dressing force is very
large and it is easy to produce vibration, because in addition to certain restrictions on the
width of the roller. the following two conditions must be met:
(1) It should be ensured that the clearance between the roller and the mandrel is ≤ 2um
when using the diamond roller.
(2) Deflection of working surface of roller ≤ 4um.
Still have vibration If the above 2 conditions are met. Indicating that the dressing force is
too large so the ar cutting amount and roller speed ratio are should be reduced.
6. Cooling
The roller should be equipped with sufficient high-pressure cooling device when dressing
the grinding wheel. The acid-base (PH value) of the coolant should be as neutral as
possible. If the acid-base is too high, the coolant will corrode the metal bond of the roller.
Start the grinding wheel and roller, and fully open the coolant.
7. Precautions
5. Collisional contact is prohibited when the feed wheel is in contact with the roller.
Otherwise the roller will be directly scrapped or cause a major machine tool accident.
Significantly reduce the service life of the roller.
8. Conclusion
1. The diamond roller has the following functions for grinding particles of the grinding
wheel:
(1) Cutting into the radial squeeze effect.
(2) The axial rotation of the grinding wheel particles. The larger the dressing amount, the
more obvious the squeezing. The grinding wheel is dominated by particle crushing. The
broken particles form a sharp edge, and the Rts becomes larger. When the dressing is
mainly grinding, the abrasive grains of the grinding wheel are flattened, the grinding wheel
is relatively smooth, and the surface finish of the workpiece becomes higher.
2. It is recommended that diamond rollers should be forward dressing, and reverse
dressing will affect the life of the rollers.
3. The common line speed ratio is +0.2 to +0.4, and the adjustable line speed ratio is
between +0.2 and +0.8, and must not exceed +1. (Refer to the figure above for the
relationship between speed ratio and grinding wheel roughness)
4. It is recommended that the roller dressing feed ar=0.1~1.0μm/r every time the grinding
wheel rotates once when dressing. Can't be >2um, if the trimming feed is too large, it will
damage the rollers, lose precision and reduce life span.
5. According to the specific requirements of the user's processed products and the
different materials of the grinding wheel, the appropriate dressing time should be selected.
The general dressing delay (the delay after the grinding wheel is trimmed to the size) is
0-5s.
Standard Accuracy of diamond rolls
Standard Accuracy of diamond rolls
Measure of length: ± 0,002 mm
Measure of step: ± 0,002 mm
Radius (for radii < 20 mm) : ± 0,002 mm
Angle (dependent on the side length): ± 1‘
Evenness: ± 0,002 mm
6. Line shape: 0,0015 mm
Concentric run-out, related to an area A: 0,002 mm
Cylinder shape: 0,002 mm
Evenness, area of contact: 0,002 mm
Rectangularity, area of contact related to the bore: 0,002 mm
Axial run-out, area of contact related to the bore: 0,002 mm
Concentric run-out, complete profile related to the inspection collar: 0,002 mm
Concentric run-out, diamond coating related to the bore: 0,003 mm
Diameter of the bore: Tolerance class H3
Contact:
Miss. Anna
Mobile/What's App:+86 15617785923
Skype: Annawng
WeChat:15617785923
E-mail:
Anna.wang@moresuperhard.com
www.moresuperhard.com
www.pcdgrinding.cn
www.morediamondwheel.com
www.mogrinding.com
www.morecuttingtools.com
www.moresuperhard.cn