The document provides information on Volvo diesel engines D11F, D13F, D16F, D11H, D13H, and D16H. It describes the engines' components and systems, including cylinders, valves, camshaft, turbocharger, fuel system, cooling system, and engine identification plates. It also discusses the engine control unit's protection functions, parameters, and diagnostic codes.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdftepu22753653
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdfdai20nao
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdfrou774513po
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdfzhenchun51
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdff8iosedkdm3e
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdffijsekkkdmdm3e
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdflunrizan628
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdftepu22753653
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdfdai20nao
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdfrou774513po
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdfzhenchun51
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdff8iosedkdm3e
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdffijsekkkdmdm3e
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdflunrizan628
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdffapanhe306271
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdfdai20nao
This document provides information on engines D11H, D13H, and D16H, including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have identification plates providing serial numbers and other identifying information.
- Drawings show the location of major engine components.
- Information is provided on engine protection functions, parameters, tests, calibrations and programming available in the VCADS Pro software.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdfrou774513po
This document provides information about engines D11H, D13H, and D16H. It describes the engines as straight six-cylinder, four-stroke diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation. The document discusses engine identification, automatic engine shutdown, engine protection functions, warning lights, torque limitation, forced idle, engine shutdown, and speed limits. It also lists relevant diagnostic codes and available VCADS Pro operations for testing components and exhaust aftertreatment systems.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdfzhenchun51
This document provides information on engines D11H, D13H, and D16H, including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have identification plates providing serial numbers and other identifying information.
- Drawings show the location of major engine components.
- Information is provided on engine protection functions, parameters, tests, calibrations and programming available in the VCADS Pro software.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdff8iosedkdm3e
This document provides information about engines D11H, D13H, and D16H, including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have identification plates providing serial numbers and other identifying information.
- Drawings show the locations of major engine components.
- Information is provided on engine protection functions, parameter settings, diagnostic codes, and other technical specifications.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdftepu22753653
This document provides information on engines D11H, D13H, and D16H, including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have identification plates providing serial numbers and other identifying information.
- Drawings show the locations of major engine components.
- Information is provided on engine protection functions, parameters, tests, calibrations and programming available in the VCADS Pro service tool.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdffijsekkkdmdm3e
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdflunrizan628
This document provides information on engines D11H, D13H, and D16H, including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have identification plates that indicate the serial number, part number, and manufacturing site.
- The document also provides the locations of engine components and procedures for changing the engine control unit.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdffapanhe306271
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo EC380D L EC380DL Excavator Service Repair Manual Instant Download.pdftepu22753653
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo EC380D L EC380DL Excavator Service Repair Manual Instant Download.pdfdai20nao
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo EC380D L EC380DL Excavator Service Repair Manual Instant Download.pdff8ioseoodkmmd
This document provides information about engines D11H, D13H, and D16H. It describes the engines as straight six-cylinder, four-stroke diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation. The document discusses engine identification, automatic engine shutdown, engine protection functions, warning lights, torque limitation, forced idle, engine shutdown, and speed limits. It also lists relevant diagnostic codes and available VCADS Pro operations for testing components and exhaust aftertreatment systems.
Volvo EC380D L EC380DL Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo EC380D L EC380DL Excavator Service Repair Manual Instant Download.pdflunrizan628
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo EC380D L EC380DL Excavator Service Repair Manual Instant Download.pdffapanhe306271
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo L220G Wheel Loader Service Repair Manual Instant Download.pdftepu22753653
This document provides instructions for changing a non-programmed E-ECU (engine control unit) on an engine with MID 128. The steps include: placing the machine in service position 1, connecting the VCADS Pro programming tool, turning off voltage, removing covers, disconnecting connectors and hoses from the old ECU, replacing the ECU, reconnecting connectors and hoses, and finishing installation. Connectors are unplugged, cable clamps removed, cooling coil disconnected, and the non-programmed ECU is replaced with a new one which must then be programmed using the VCADS Pro tool.
Volvo L220G Wheel Loader Service Repair Manual Instant Download.pdff8ioseoodkmmd
This document provides instructions for changing a non-programmed E-ECU (engine control unit) on an engine with MID 128. The steps include: placing the machine in service position 1, connecting the VCADS Pro programming tool, turning off voltage, removing covers, disconnecting connectors and hoses from the old ECU, replacing the ECU, reconnecting connectors and hoses, and finishing installation. Connectors are unplugged, cable clamps removed, cooling coil disconnected, old ECU replaced with new one, then cooling coil, connectors and clamps are reinstalled.
Volvo L220G Wheel Loader Service Repair Manual Instant Download.pdffapanhe306271
This document provides instructions for changing a non-programmed E-ECU (engine control unit) on an engine with MID 128. The steps include: placing the machine in service position 1, connecting the VCADS Pro programming tool, turning off voltage, removing covers, disconnecting connectors and hoses from the old ECU, replacing the ECU, reconnecting connectors and hoses, and finishing installation. Connectors are unplugged, cable clamps removed, cooling coil disconnected, old ECU replaced with new one, then cooling coil, connectors and clamps are reinstalled.
Volvo EC360C L EC360CL Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides instructions for removing and installing an engine. It describes disconnecting hoses, electrical connections, removing mounting hardware and lifting the engine out. When installing, it describes connecting all hoses and electrical connections, installing mounting hardware, and filling fluids before starting the engine to check for leaks.
Volvo EC360B LC EC360BLC Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides information about adjusting the valves on an engine. It begins with removing necessary covers and components to access the valves. Then it describes how to adjust the inlet and exhaust valves by loosening and tightening adjustment screws and lock nuts while checking clearance with a feeler gauge. A similar process is used to adjust the double rocker arm, checking clearance with a special tool. Safety precautions and proper tightening torques are noted. Diagrams illustrate the components and steps in the process.
Volvo EC360 LC EC360LC Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides information on engine components and systems:
- The engine is a 6-cylinder diesel with a cast iron block and head, direct injection, and turbocharging.
- It has a lubrication system that supplies oil to rotating components through forced lubrication from an oil pump.
- The fuel injection system uses a high-pressure fuel pump to directly inject fuel into the combustion chamber, with excess returning to the tank.
- Other sections provide details on valve and injector adjustment procedures, engine mounting, and fuel tank components.
More Related Content
Similar to Volvo A25F Articulated Dump Truck Service Repair Manual Instant Download.pdf
Volvo EC340D L EC340DL Excavator Service Repair Manual Instant Download.pdffapanhe306271
This document provides information on engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and lists available VCADS Pro operations.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdfdai20nao
This document provides information on engines D11H, D13H, and D16H, including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have identification plates providing serial numbers and other identifying information.
- Drawings show the location of major engine components.
- Information is provided on engine protection functions, parameters, tests, calibrations and programming available in the VCADS Pro software.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdfrou774513po
This document provides information about engines D11H, D13H, and D16H. It describes the engines as straight six-cylinder, four-stroke diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation. The document discusses engine identification, automatic engine shutdown, engine protection functions, warning lights, torque limitation, forced idle, engine shutdown, and speed limits. It also lists relevant diagnostic codes and available VCADS Pro operations for testing components and exhaust aftertreatment systems.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdfzhenchun51
This document provides information on engines D11H, D13H, and D16H, including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have identification plates providing serial numbers and other identifying information.
- Drawings show the location of major engine components.
- Information is provided on engine protection functions, parameters, tests, calibrations and programming available in the VCADS Pro software.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdff8iosedkdm3e
This document provides information about engines D11H, D13H, and D16H, including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have identification plates providing serial numbers and other identifying information.
- Drawings show the locations of major engine components.
- Information is provided on engine protection functions, parameter settings, diagnostic codes, and other technical specifications.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdftepu22753653
This document provides information on engines D11H, D13H, and D16H, including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have identification plates providing serial numbers and other identifying information.
- Drawings show the locations of major engine components.
- Information is provided on engine protection functions, parameters, tests, calibrations and programming available in the VCADS Pro service tool.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdffijsekkkdmdm3e
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdflunrizan628
This document provides information on engines D11H, D13H, and D16H, including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have identification plates that indicate the serial number, part number, and manufacturing site.
- The document also provides the locations of engine components and procedures for changing the engine control unit.
Volvo EC380D NL EC380DNL Excavator Service Repair Manual Instant Download.pdffapanhe306271
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo EC380D L EC380DL Excavator Service Repair Manual Instant Download.pdftepu22753653
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo EC380D L EC380DL Excavator Service Repair Manual Instant Download.pdfdai20nao
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo EC380D L EC380DL Excavator Service Repair Manual Instant Download.pdff8ioseoodkmmd
This document provides information about engines D11H, D13H, and D16H. It describes the engines as straight six-cylinder, four-stroke diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation. The document discusses engine identification, automatic engine shutdown, engine protection functions, warning lights, torque limitation, forced idle, engine shutdown, and speed limits. It also lists relevant diagnostic codes and available VCADS Pro operations for testing components and exhaust aftertreatment systems.
Volvo EC380D L EC380DL Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo EC380D L EC380DL Excavator Service Repair Manual Instant Download.pdflunrizan628
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo EC380D L EC380DL Excavator Service Repair Manual Instant Download.pdffapanhe306271
This document provides information about engines D11H, D13H, and D16H including:
- They are straight six-cylinder, four-stroke, direct-injected diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation.
- The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft.
- The document provides information on engine identification, component locations, procedures for changing a non-programmed or pre-programmed ECU, and available VCADS Pro operations.
Volvo L220G Wheel Loader Service Repair Manual Instant Download.pdftepu22753653
This document provides instructions for changing a non-programmed E-ECU (engine control unit) on an engine with MID 128. The steps include: placing the machine in service position 1, connecting the VCADS Pro programming tool, turning off voltage, removing covers, disconnecting connectors and hoses from the old ECU, replacing the ECU, reconnecting connectors and hoses, and finishing installation. Connectors are unplugged, cable clamps removed, cooling coil disconnected, and the non-programmed ECU is replaced with a new one which must then be programmed using the VCADS Pro tool.
Volvo L220G Wheel Loader Service Repair Manual Instant Download.pdff8ioseoodkmmd
This document provides instructions for changing a non-programmed E-ECU (engine control unit) on an engine with MID 128. The steps include: placing the machine in service position 1, connecting the VCADS Pro programming tool, turning off voltage, removing covers, disconnecting connectors and hoses from the old ECU, replacing the ECU, reconnecting connectors and hoses, and finishing installation. Connectors are unplugged, cable clamps removed, cooling coil disconnected, old ECU replaced with new one, then cooling coil, connectors and clamps are reinstalled.
Volvo L220G Wheel Loader Service Repair Manual Instant Download.pdffapanhe306271
This document provides instructions for changing a non-programmed E-ECU (engine control unit) on an engine with MID 128. The steps include: placing the machine in service position 1, connecting the VCADS Pro programming tool, turning off voltage, removing covers, disconnecting connectors and hoses from the old ECU, replacing the ECU, reconnecting connectors and hoses, and finishing installation. Connectors are unplugged, cable clamps removed, cooling coil disconnected, old ECU replaced with new one, then cooling coil, connectors and clamps are reinstalled.
Similar to Volvo A25F Articulated Dump Truck Service Repair Manual Instant Download.pdf (19)
Volvo EC360C L EC360CL Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides instructions for removing and installing an engine. It describes disconnecting hoses, electrical connections, removing mounting hardware and lifting the engine out. When installing, it describes connecting all hoses and electrical connections, installing mounting hardware, and filling fluids before starting the engine to check for leaks.
Volvo EC360B LC EC360BLC Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides information about adjusting the valves on an engine. It begins with removing necessary covers and components to access the valves. Then it describes how to adjust the inlet and exhaust valves by loosening and tightening adjustment screws and lock nuts while checking clearance with a feeler gauge. A similar process is used to adjust the double rocker arm, checking clearance with a special tool. Safety precautions and proper tightening torques are noted. Diagrams illustrate the components and steps in the process.
Volvo EC360 LC EC360LC Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides information on engine components and systems:
- The engine is a 6-cylinder diesel with a cast iron block and head, direct injection, and turbocharging.
- It has a lubrication system that supplies oil to rotating components through forced lubrication from an oil pump.
- The fuel injection system uses a high-pressure fuel pump to directly inject fuel into the combustion chamber, with excess returning to the tank.
- Other sections provide details on valve and injector adjustment procedures, engine mounting, and fuel tank components.
Volvo EC300D NL EC300DNL Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides service information about an engine. It describes the engine as a 6-cylinder 4-stroke turbocharged diesel engine that meets Tier 4 emissions standards. It has features like a common rail fuel system and exhaust aftertreatment system. The document provides information on removing the engine, which involves draining fluids, removing hoses, disconnecting electrical connections, and removing mounting hardware.
Volvo EC300D LR EC300DLR Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides information about the cooling system of an excavator, including:
1. The cooling system uses a pump to circulate coolant throughout the engine and radiator to transfer heat.
2. A thermostat regulates coolant flow and a fan cools the radiator through airflow.
3. Procedures are provided for checking coolant levels and replacing components like hoses, the radiator, expansion tank, and thermostat.
Volvo EC300D L (EC300DL) Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides service information for an engine. It describes the engine as a 6-cylinder turbocharged diesel engine that meets Tier 4 emissions standards. It also summarizes the engine's fuel, exhaust, cooling, and electronic control systems. The document then provides instructions for removing the engine, which involves draining fluids, disconnecting hoses and electrical connections, and removing mounting hardware.
Volvo EC290C NL EC290CNL Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides technical service information about an engine, including:
1. A description of the D7E engine as a four-stroke, six-cylinder turbocharged diesel with charge air cooling and wet cylinder liners.
2. Details on the identification plate containing the engine model, serial number, and performance data located on the cylinder head cover.
3. A table listing tightening torques for various engine components.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides technical specifications and descriptions for various engine components of the D7E engine, including:
- The cylinder head is made of grey cast iron with vertical air intake and horizontal exhaust outlets. It uses three different thickness cylinder head gaskets.
- The cylinder block is cast in one piece with wet, replaceable cylinder liners. Combustion pressure is directed to the main bearings.
- The cylinder liner is sealed at the bottom by two O-rings and at the top by the cylinder head gasket and clamping force.
- The pistons are made of special alloy aluminum with an eccentric combustion compartment position.
Volvo EC290C LD (EC290CLD) Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides information on the D7E engine configuration used in Volvo excavators, including:
- The D7E engine is a four-stroke, straight six cylinder turbocharged diesel with charge air cooling and wet cylinder liners.
- It uses a Common Rail fuel system and IEGR to reduce emissions without exhaust aftertreatment.
- The cylinders are numbered beginning at the flywheel end and the engine rotates counterclockwise.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290B NLC EC290BNLC Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides information on an engine, including:
1. The engine is a 6-cylinder, 4-stroke diesel engine with a cast iron block and head. It uses direct injection, turbocharging, and air-to-air cooling.
2. The document describes various engine components like the cylinder head, pistons, valves, and an internal exhaust gas recirculation system.
3. It also provides engine specifications, diagrams, and instructions for basic checks, troubleshooting, and maintenance of the engine.
Volvo EC290B LR (EC290BLR) Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides information on an engine, including:
1. The engine is a 6-cylinder, 4-stroke diesel engine with a cast iron block and head. It uses direct injection, turbocharging, and air-to-air cooling.
2. The document includes descriptions of various engine components like the cylinder head, liners, pistons, rings, valves, and an internal exhaust gas recirculation system.
3. It also provides an engine characteristic curve showing power, torque, and fuel consumption curves. Basic checks, troubleshooting information, and service information are outlined.
Volvo EC290B LC (EC290BLC) Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides information on an engine, including:
1. The engine is a 6-cylinder, 4-stroke diesel engine with a cast iron block and head. It uses direct injection, turbocharging, and aftercooling.
2. The document includes diagrams and descriptions of the engine components, such as the cylinder head, liners, pistons, rings, valves, and internal exhaust gas recirculation system.
3. Troubleshooting information and procedures are also outlined, such as checking codes, parameters, and performing basic engine tests to diagnose issues.
Volvo EC290B FX (EC290BFX) Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides information on an engine, including:
1. The engine is a 6-cylinder, 4-stroke diesel engine with a cast iron block and head. It uses direct injection, turbocharging, and aftercooling.
2. The document includes diagrams and descriptions of the engine components such as the cylinder head, liners, pistons, rings, valves, and internal exhaust gas recirculation system.
3. The basic check procedures for the engine are also outlined, including compression checks, sensor tests, and measuring fuel pressure. Troubleshooting information and strategies are provided.
Volvo EC290 Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides information on an engine, including its description, specifications, and maintenance procedures. It describes a 6-cylinder diesel engine that is water-cooled, turbocharged, and direct injected. It provides details on the engine's components, lubrication system, and fuel injection system. The document also includes specifications, diagrams, and instructions for adjusting the engine's valves and other maintenance tasks.
Volvo EC250D NL (EC250DNL) Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides service information about an engine. It describes the engine as a 6-cylinder turbocharged diesel engine that meets Tier 4 emissions standards. It also summarizes the engine's electronic control system, exhaust aftertreatment system, and various protective functions. Procedures are provided for removing the engine, which involve draining fluids, disconnecting hoses and electrical connections, and removing mounting hardware.
Volvo EC250D LR (EC250DLR) Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides service information for an engine. It describes the engine as a straight six-cylinder turbocharged diesel engine that meets Tier 4 emissions standards. It also summarizes the key components of the engine, including the common rail fuel system and exhaust aftertreatment system. Procedures are provided for removing the engine, which involve draining fluids, disconnecting hoses and electrical connections, and removing mounting hardware.
Volvo EC250D L EC250DL Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides service information for an engine. It includes:
- A description of the engine as a 6-cylinder turbocharged diesel meeting Tier 4 emissions standards, with common rail fuel injection and an exhaust aftertreatment system.
- The location of engine components and diagrams identifying parts.
- Procedures for replacing the electronic control unit (ECU) on the engine, whether a new or pre-programmed unit.
- A list of diagnostic operations available in the VCADS Pro computer program for testing engine functions.
- An engine characteristic curve showing power and torque outputs relative to engine speed.
- Step-by-step instructions for removing the engine from the machine.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides information on an engine, including:
1. The D7E engine is a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an electronic control unit. Electronically controlled exhaust gas recirculation reduces emissions.
3. The document contains sections about various engine components like the cylinder head, cylinder block, pistons, and their descriptions.
Volvo EC240C LR EC240CLR Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides descriptions of various engine components for a Volvo EC240C LR excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust. Valve guides are replaceable.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings. Combustion pressure is directed to the main bearings.
3. The engine uses wet cylinder liners sealed with two O-rings and the cylinder head gasket.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Volvo A25F Articulated Dump Truck Service Repair Manual Instant Download.pdf
1. Service Information
Document Title: Function Group: Information Type: Date:
Engine, description 200 Service Information 2014/8/5 0
Profile:
ART, A25F (37214) [GB]
Go back to Index Page
Engine, description
Engines D11F, D13F, and D16F are straight six-cylinder, four-stroke, direct-injected diesel engines. Engines D13F and D16F
are equipped with a single turbocharger with wastegate and engine D11F has a turbocharger without wastegate. They have
charge-air cooling with mechanically actuated electronically controlled unit injectors, controlled by the EMS-system.
The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft. Rear-mounted
timing gear results in a shorter engine and lighter drivetrain installation. Engine brake for Articulated Hauler; VEB+ (EPG,
Exhaust Pressure Governor, and VCB, Volvo Compression Brake).
For more information, see:
220 Lubrication system, description
230 Fuel system, description
250 Inlet and exhaust system, description
255 Turbocharger, description
260 Cooling system, description
For Articulated Haulers:
253 Auxiliary brake (engine braking), description
253 Exhaust pressure governor
The cylinders are numbered in sequence, starting farthest from the flywheel. Ignition order: 1-5-3-6-2-4. The engine's
rotational direction is counter-clockwise, seen from the flywheel.
Engine identification
2. Figure 1
Identification plates, D13F
Identification plate 1
A label located on the valve cover showing the engine's component ID-number, serial number, manufacturing site, engine
part number, and engine build date, as well as their bar codes. Manufacturing sites:
A = Skövde, Sweden
E = Curitiba, Brazil
F = Flen, Sweden
L = Lyon, France
Identification plate 2
The engine's serial number, part number, and manufacturing site are stamped into the engine's cylinder block.
Identification plate 3
The hardware component number of the Engine Control Unit (ECU) is located on a label on the back of the ECU.
Identification plate 4
The certification label is located on the valve cover as well as the machine's frame.
Automatic Engine Shutdown
This is a function used to automatically shut down the engine after idling for a certain time. The operator is informed and
has the opportunity to cancel the function within one minute, either by increasing the engine speed, shifting gear, or by
activating the hand throttle.
Engine protection
The ECU contains functionality designed to protect the engine from damage during extreme operating conditions or from
further damage when an essential engine component fails. There are several proactive functions, and different applications
have different functions activated. The ones that can be activated are:
High coolant temperature
High intake manifold air pressure
High intake manifold air temperature
High oil temperature
Low oil pressure
Low coolant level
High crankcase pressure
High ECU temperature
Various protective actions such as warning lights, engine torque reduction, engine speed limitation, and vehicle speed
limitation may be taken when the above functions reach dangerous levels that may damage the engine. In order to always
allow the operator to move a machine away from an unsafe situation, there is a delay of at least 30 seconds before the
protective actions (such as forced idle and forced shutdown) are activated after a Key-ON. If the engine has been forced to
shutdown or forced to idle due to an active engine protection function, the operator can obtain a 30 second delay by
powering down the EMS with a Key-OFF for 7 seconds and then a Key-ON (the EMS is powered down by the Vehicle-ECU
(V-ECU) after the ignition key has been in its OFF position for approx. 7 seconds). In addition to the above protective
functions, other software functions could request engine protection, such as:
High Altitude (ensures that high compressor discharge temperature is never reached)
Turbo OverSpeed
Low Coolant Temp
Crank Sensor Failure
Gear Ratio
Warning lights
There are two levels for warning lights, an amber caution light and a red stop light.
The amber light indicates a warning situation
The red light indicates that the vehicle must be stopped.
Engine torque limitation
The engine torque can be limited by the engine protection function. Engine torque limitation is active until the parameter
3. has reached a safe level or until the EMS is powered down.
Forced Idle
The engine can be forced to idle speed by the engine protection function. Forced idle is active until conditions triggering the
problem are back within normal working range or the EMS is powered down.
Engine Shutdown
The engine can be forced to shut down after conditions have reached levels that may cause engine failure and the machine
speed is below a specified value.
Machine Speed and Engine Speed Limits
The engine protection function can limit the speed of the vehicle and/or the engine's rpm.
Levels of engine protection
Available proactive functions depend not only on the application but also on what level of protection has been activated for
the specific machine. Two levels of engine protection are offered, the standard level is Basic protection and the optional level
Extended protection. The general difference between basic and extended engine protection is that no active actions such as
forced idle and forced shutdown will be taken in basic engine protection (with the exception of crankcase pressure that can
cause shutdown in either setup). Warnings will be given to the operator regardless of engine protection level.
Parameters
(ATJ) Injector cylinder 1, calibration
(ATK) Injector cylinder 2, calibration
(ATL) Injector cylinder 3, calibration
(ATM) Injector cylinder 4, calibration
(ATN) Injector cylinder 5, calibration
(ATO) Injector cylinder 6, calibration
(FAU) Automatic engine shut off
(FAV) Automatic engine shut off, time
(YA) Idle speed, setting
Supplementary information
200 Component locations
Function check
17030-3 Parameter, programming
Diagnostics
Detailed information about the following relevant warnings and error codes is available under the diagnostics tab.
Component Control unit Message ID
EF2117 (ART)
PPID55 (WLO, EXC)
MID128 PPID55
SE2202
FX1006 (WLO)
MID128 PID175
SE2507
FX1007 (WLO)
MID128 PID105
SE2203 MID128 PID100
SE2509 MID128 PID153
SE2603 MID128 PID111
SE2606 MID128 PID110
4. Service Information
Document Title: Function Group: Information Type: Date:
Engine, description 200 Service Information 2014/8/5 0
Profile:
ART, A25F (37214) [GB]
Go back to Index Page
Engine, description
Engines D11H, D13H, and D16H are straight six-cylinder, four-stroke, direct-injected diesel engines. They are equipped with
a single variable geometry turbocharger (VGT) and feature cooled external exhaust gas recirculation (EGR). They have
charge-air cooling with mechanically actuated electronically controlled unit injectors, controlled by the EMS-system.
The engines have a one-piece cylinder head with four valves per cylinder and a single overhead camshaft. Rear-mounted
timing gear results in a shorter engine and lighter drivetrain installation. The engine brake for articulated haulers, VEB7, does
not have the additional Exhaust Pressure Governor, EPG. Sufficient exhaust back-pressure will be controlled via the VGT.
For more information, see:
220 Lubrication system, description
230 Fuel system, description
250 Inlet and exhaust system, description
254 Exhaust Aftertreatment System, description
255 Turbocharger, description
260 Cooling system, description
293 Exhaust Gas Recirculation (EGR), description
For Articulated Haulers:
253 Auxiliary brake (engine braking), description
The cylinders are numbered in sequence, starting farthest from the flywheel. Ignition order: 1-5-3-6-2-4. The engine's
rotational direction is counter-clockwise, seen from the flywheel.
Engine identification
5. Figure 1
Identification plates, D13H
Identification plate 1
A label located on the valve cover showing the engine's component ID-number, serial number, manufacturing site, engine
part number, and engine build date, as well as their bar codes. Manufacturing sites:
A = Skövde, Sweden
E = Curitiba, Brazil
F = Flen, Sweden
L = Lyon, France
Identification plate 2
The engine's serial number, part number, and manufacturing site are stamped into the engine's cylinder block.
Identification plate 3
The hardware component number of the Engine Control Unit (ECU) is located on a label on the back of the ECU.
Identification plate 4
The certification label is located on the valve cover as well as the machine's frame.
Automatic Engine Shutdown
This is a function used to automatically shut down the engine after idling for a certain time. The operator is informed and
has the opportunity to cancel the function within one minute, either by increasing the engine speed, shifting gear, or by
activating the hand throttle.
Engine protection
The ECU contains functionality designed to protect the engine from damage during extreme operating conditions or from
further damage when an essential engine component fails. There are several proactive functions, and different applications
have different functions activated. The ones that can be activated are:
High coolant temperature
6.
High intake manifold air pressure
High intake manifold air temperature
High oil temperature
Low oil pressure
Low coolant level
High temperature of cooled EGR exhausts after the EGR-cooler
High crankcase pressure
Variable Geometry Turbo valve and position error
High temperature of Smart Remote Actuator
High compressor charge-air temperature (calculated)
High soot load
High differential pressure across Diesel Particulate Filter (DPF)
High exhaust temperature
High ECU temperature
High DPF temperature
Various protective actions such as warning lights, engine torque reduction, engine speed limitation, and vehicle speed
limitation may be taken when the above functions reach dangerous levels that may damage the engine. In order to always
allow the operator to move a machine away from an unsafe situation, there is a delay of at least 30 seconds before the
protective actions (such as forced idle and forced shutdown) are activated after a Key-ON. If the engine has been forced to
shutdown or forced to idle due to an active engine protection function, the operator can obtain a 30 second delay by
powering down the EMS with a Key-OFF for 7 seconds and then a Key-ON (the EMS is powered down by the Vehicle-ECU
(V-ECU) after the ignition key has been in its OFF position for approx. 7 seconds). In addition to the above protective
functions, other software functions could request engine protection, such as:
High Altitude (ensures that high compressor charge-air temperature is never reached)
Turbo OverSpeed
Low Coolant Temp
Crank Sensor Failure
Gear Ratio
Regeneration
Warning lights
There are two levels for warning lights, an amber caution light and a red stop light.
The amber light indicates a warning situation
The red light indicates that the vehicle must be stopped.
Engine torque limitation
The engine torque can be limited by the engine protection function. Engine torque limitation is active until the parameter
has reached a safe level or until the EMS is powered down.
Forced Idle
The engine can be forced to idle speed by the engine protection function. Forced idle is active until conditions triggering the
problem are back within normal working range or the EMS is powered down.
Engine Shutdown
The engine can be forced to shut down after conditions have reached levels that may cause engine failure and the machine
speed is below a specified value.
Machine Speed and Engine Speed Limits
The engine protection function can limit the speed of the vehicle and/or the engine's rpm.
Levels of engine protection
Available proactive functions depend not only on the application but also on what level of protection has been activated for
the specific machine. Two levels of engine protection are offered, the standard level is Basic protection and the optional level
Extended protection. The general difference between basic and extended engine protection is that no active actions such as
forced idle and forced shutdown will be taken in basic engine protection (with the exception of crankcase pressure that can
cause shutdown in either setup). Warnings will be given to the operator regardless of engine protection level.
Parameters
(FAU) Automatic engine shut off
(FAV) Automatic engine shut off, time
7.
(JVL) Injector cylinder 1, calibration E3 Glitch Trim
(JVM) Injector cylinder 2, calibration E3 Glitch Trim
(JVN) Injector cylinder 3, calibration E3 Glitch Trim
(JVO) Injector cylinder 4, calibration E3 Glitch Trim
(JVP) Injector cylinder 5, calibration E3 Glitch Trim
(JVQ) Injector cylinder 6, calibration E3 Glitch Trim
(YA) Idle speed, setting
Supplementary information
200 Component locations
Function check
17030-3 Parameter, programming
Diagnostics
Detailed information about the following relevant warnings and error codes is available under the diagnostics tab.
Component Control unit Message ID
EF2112 (ART)
PID404 (EXC, WLO)
MID128 PID404
EF2117 (ART)
PPID55 (WLO, EXC)
MID128 PPID55
EF2127 (ART)
PPID89 (EXC, WLO)
MID128 PPID89
EF2515 (ART)
PSID28 (WLO, EXC)
MID128 PSID28
EF2525 (ART)
PID173 (EXC)
SE2510 (WLO)
MID128 PID173
SE2202
FX1006 (WLO)
MID128 PID175
SE2507
FX1007 (WLO)
MID128 PID105
MO2501 MID128 SID27
PPID326 (WLO, EXC) MID128 PPID326
SE2203 MID128 PID100
SE2509 MID128 PID153
SE2516 MID128 PID412
SE2519 MID128 PID81
SE2603 MID128 PID111
SE2606 MID128 PID110
8. Service Information
Document Title: Function Group: Information Type: Date:
Engine, sensor positions 200 Service Information 2014/8/5 0
Profile:
ART, A25F (37214) [GB]
Engine, sensor positions
Control unit sensors
This is a brief description of the sensors that are found on the engine.
Figure 1
1.
2.
3.
4.
5.
6.
7.
Sensor for crankcase pressure, SE2509
Sensor for charge-air temperature, SE2512 (only engine with EGR)
Sensor for boost pressure/charge-air temperature, SE2507/SE2508 FX1007
Tachometer sensor, flywheel, SE2701
Sensor for coolant temperature, cooling circuit engine/retarder, SE2602
Sensor for coolant temperature, cooling circuit converter, SE2601
Sensor for oil level/oil temperature, SE2205/SE2202 FX1006
9. Figure 2
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Sensor for coolant level, SE2603
Speed sensor (rpm), turbocharger SE2514
Temperature sensor EGR SE2516
Sensor, coolant temperature SE2606
Sensor, EGR-flow SE2515
Sensor for oil pressure, SE2203
Sensor for water indicator, SE2302
Sensor for fuel pressure, SE2301
Camshaft sensor, engine position, SE2703
Sensor for air pressure/air temperature, SE2501/SE2502 FX1008
10. Service Information
Document Title: Function Group: Information Type: Date:
Engine, identification 200 Service Information 2014/8/5 0
Profile:
ART, A25F (37214) [GB]
Engine, identification
Identification plate 1
A decal with the software's ID-number, the engine's serial number and assembly plant is located on the valve cover to
ensure installation of correct ECU on the engine in production. On the back of the ECU, there is a decal indicating its
hardware number.
Identification plate 2
Engine designation, serial number, part number and assembly plant are stamped in one field on the engine block's left front
edge.
Assembly plants:
A = Skövde, Sweden
E = Curitiba, Brazil
F = Flen, Sweden
L = Lyon, France
Identification plate 3
The engine control unit (ECU) has its component number on a plate on the back.
Identification plate 4
The certification decal is located on the valve cover as well as on the left side of the machine's front frame.
Figure 1
Product plate
11. Figure 2
Engine versions
In order to offer machines with lower environmental impact, two main engine types have been developed for machines in
the F-series. One version developed for generally available fuel and oil grades, and a version that meets higher emission
requirements. The easiest way to see on the machine what version it is, check if it has a diesel particle filter (Diesel Particulate
Filter) in the muffler. See: .
254 Exhaust Aftertreatment System, description
Machine Engine designation Diesel Particulate Filter
A25F D11F No
A25F D11H Yes
A30F D11F No
A30F D11H Yes
A35F D13F No
A35F D13H Yes
A40F D16F No
A40F D16H Yes
12. Service Information
Document Title: Function Group: Information Type: Date:
VCADS Pro, Operations 200 Service Information 2014/8/5 0
Profile:
ART, A25F (37214) [GB]
VCADS Pro, Operations
The following VCADS Pro operations are available for function group 2. Operations used when changing or working on
components are mandatory.
NOTE!
Operations used when changing or repairing components are mandatory.
NOTE!
New operations are developed regularly. For a current list of all tests, see VCADS Pro software.
Tests
Operation Application
20046-3 Read out engine information The test is used to read out engine emissions and engine certification
information.
21006-3 Cylinder compression, test The test shows whether the compression of any cylinder differs from
that of the other cylinders.
23016-3 Cylinder balancing, test The test shows whether fuel injection on any cylinder differs from that
on the other cylinders.
23017-3 Feed pressure, inspection The test is used to check feed pressure.
23712-3 Injectors shut off, manual The test supplements cylinder balancing. In the test, one injector at a
time can be turned off manually.
25410-3 Air pump exhaust aftertreatment, test The test is used to check cut-in and cut-out of the air pump for the
exhaust aftertreatment system.
25411-3 Burner exhaust aftertreatment, test The test is used to diagnose the exhaust aftertreatment system. The
test activates the built-in diagnostic function in the control unit. The
test indicates any failure with a red light. Read out error codes with
operation 17012-3, Error codes.
25412-3 Components ASU, test This subtest is used to check function of the atomization unit's air
valve, main air valve, the fuel's shut-off valve, and the fuel pump.
25433-3 Fuel system exhaust aftertreatment,
bleeding
The test is used to purge any air in the fuel system for the
atomization unit.
25434-3 Atomization unit, fuel pressure, adjust The test is used to adjust the fuel pressure in the atomization unit.
25456-3 Exhaust aftertreatment diagnostics The test is used to check status of the included components for the
exhaust aftertreatment.
25457-3 Diesel Particulate Filter Service
Regeneration
This operation is used when the soot load is above 1.7, see
.
254 Exhaust Aftertreatment System, description
In this operation, status and a number of sensor values can be read
out during on-going regeneration.
Also check that "DPF differential pressure" is within permitted values,
both before and after regeneration, see
.
254 Exhaust aftertreatment system, specifications
25537-3 Variable geometry turbo function test The test is used to check function of the variable geometry turbo
(VGT).
26351-3 Hydraulic cooling fan, test The test controls the cooling fans' speed control (independent of
ordinary control) and is used when adjusting speed.
27102-3 Accelerator pedal, test The test is used to check function of the throttle pedal.
13. 28407-3 Sensor values, monitoring The tests show values (temperature, rpm, etc.) that the system
receives from connected sensors and monitors.
28420-3 Flywheel and camshaft signal, test The test is used to use an oscilloscope to check signals from the
flywheel and camshaft position sensors.
29332-3 Exhaust gas circulation, function test The test is used to check function of the exhaust gas recirculation.
Calibrations
Operation Application
25536-3 Variable geometry turbo, calibration When changing actuator, see
.
255 Actuator, variable turbocharger, replacing
Programming
Operation Application
25801-3 MID 233 Control unit, programming When changing control unit or when reprogramming complete or
part of the software.
25802-3 MID 233 Control unit, campaign Use for campaign programming of the control unit.
28422-3 MID 128 ECU, campaign Use for campaign programming of the control unit.
28423-3 MID 128 ECU, programming When changing control unit or when reprogramming complete or
part of the software.
14. Service Information
Document Title: Function Group: Information Type: Date:
E-ECU, MID 128, changing
pre-programmed ECU
200 Service Information 2014/8/5 0
Profile:
ART, A25F (37214) [GB]
E-ECU, MID 128, changing pre-programmed ECU
Op nbr 200-070
This operation also includes required tools and times for applicable parts of the following operations:
191 Service positions
200 E-ECU, MID 128, changing non-programmed ECU
1. Place the machine in service position, see .
191 Service positions
2. Connect VCADS Pro computer and perform 17030-3 Parameter, programming.
Use the function: Save all read parameters to job card.
3. Run from and including step 3 and on.
200 E-ECU, MID 128, changing non-programmed ECU
4. Connect VCADS Pro computer and perform 17030-3 Parameter, programming.
Program earlier read-out parameters according to the job card.
5. Restore the machine to operating condition.
15. Service Information
Document Title: Function Group: Information Type: Date:
E-ECU, MID 128, changing
non-programmed ECU
200 Service Information 2014/8/5 0
Profile:
ART, A25F (37214) [GB]
E-ECU, MID 128, changing non-programmed ECU
Op nbr 200-068
This operation also includes the tools and times needed for required parts of the following actions:
191 Service positions
1. Place the machine in service position, see .
191 Service positions
2. Connect VCADS Pro computer and perform 28423-3 MID 128 ECU, programming.
When instructed to connect the new control unit, perform steps 3-21.
CAUTION
Always follow instructions according to Electrical system, work instructions, electronic components
3001 Electrical system, special instructions for servicing, electronic components
CAUTION
Always follow instructions according to Electrical system, work instructions, electronic components
3. Removing
Open the engine hood.
4. Turn off the main electric power with the battery disconnector.
5. Disconnect the radiator from its front bracket. Swing out the radiator for easier access to the control unit.
NOTE!
Protect the charge-air cooler with a cloth or board.
6. Remove the screws, which releases the clamps from the E-ECU.
7. Unplug the connectors EA (7), EB (8), and EI (4).
16. Figure 1
E-ECU
1.
2.
3.
4.
5.
6.
7.
8.
Oil separator
Pressure-oil line
E-ECU
Connector EI
Cooling unit
Fuel hoses
Connector EA
Connector EB
8. Loosen the pressure-oil line (2) from the oil separator (1).
9. Cut the cable ties on the fuel hoses (6).
NOTE!
Note grouping (bunching) of the hoses to facilitate installation.
10. Loosen the cooling unit (5) from the E-ECU (6 bolts). Carefully move aside the cooling unit.
NOTE!
Work carefully so that hoses for the cooler are not damaged.
11. Remove the E-ECU.
12. Installing
Fit the E-ECU.
13. Connect the cooling unit (5) to the E-ECU.
Figure 2
17. E-ECU
1.
2.
3.
4.
5.
6.
7.
8.
Oil separator
Pressure-oil line
E-ECU
Connector EI
Cooling unit
Fuel hoses
Connector EA
Connector EB
14. Connect the pressure-oil line (2) to the oil separator (1).
15. Connect the connectors EA (7), EB (8), and EI (4).
16. Install the screws that fasten the clamps to the E-ECU.
17. Fasten the fuel hoses (6) according to earlier notes.
18. Connect the radiator to the front bracket.
19. Close the engine hood.
NOTE!
When changing pre-programmed control unit, go back to 200 E-ECU, MID 128, changing pre-programmed ECU
step 4.
20. Finish VCADS Pro operation 28423-3 MID 128 ECU, programming.
21. Restore the machine to operating condition.
18. Service Information
Document Title: Function Group: Information Type: Date:
Cylinder compression, PC
test
210 Service Information 2014/8/5 0
Profile:
ART, A25F (37214) [GB]
Cylinder compression, PC test
Connect the VCADS Pro computer and carry out 21006-3 Cylinder compression, test.
(21006-3) This test indicates if there is any deviation in compression in any cylinder in relation to the other cylinders.
19. Service Information
Document Title: Function Group: Information Type: Date:
Engine and transmission,
removing
210 Service Information 2014/8/5 0
Profile:
ART, A25F (37214) [GB]
Engine and transmission, removing
Op nbr 210-073
This operation also includes required tools and times for applicable parts of the following operations:
191 Service positions
173 Coolant, changing
900 Vacuum pump, connection
715 Protective plate, removing
WARNING
Changing control units between machines, when troubleshooting or repairing, may not take place for any reason
without reprogramming.
Incorrect individual settings in the control unit may result in personal injury or machine damage.
For reprogramming and read-out of software, see "VCADS Pro User manual".
1. Place the machine in service position, see 191 Service positions
2. Swing down the front grill and open the engine hood.
Figure 1
3. Turn off the electric power with the battery disconnect switch.
4. Remove the front and rear underbody skid plates. See .
715 Protective plate, removing
20. Figure 2
1.
2.
3.
4.
5.
Front underbody skid plate
Rear underbody skid plate, left
Rear underbody skid plate, right
Front cross member
Rear cross member
5. Remove the front and rear cross members.
Weight: approx.15 kg (33 lbs).
WARNING
Risk of burns. The fluid may be hot.
6. NOTE!
Take care of waste oil/fluids in an environmentally sound manner.
NOTE!
The oil drain hose is inserted in the pipe for the ladder on the inside of the front grill.
Drain the gearbox oil.
Volume, see: 400 Drive train capacities
Figure 3
Draining transmission oil
7. Drain the coolant, see: 173 Coolant, changing
Work in engine compartment
8. Remove the front protective plates and the belt guard.
21. Figure 4
9. Remove the bolt and swing out the radiator.
Figure 5
NOTE!
Keep in mind that the cooling fins are easily damaged. To protect them, install a sheet of plywood or similar.
10. Loosen the belt tensioners with a half inch ratchet handle and remove the three belts.
Figure 6
22. 11. Loosen and remove the connections for the preheating coil and the pipe for compressed air from the compressor.
Remove the coolant hoses and the joint. Remove the compressor's signal line.
Figure 7
1.
2.
3.
4.
5.
Compressed air pipe
Plus cable
Joint
Lower coolant hose
Upper coolant hose
12. Unplug the connector (EL). Remove the cable clamp.
Figure 8
13. WARNING
Do not disconnect or loosen connections for the air conditioning unit (AC). Risk of gas leakage.
Unplug the connector for control current to the AC compressor. Remove the bolts and remove the AC compressor.
Put it aside.
23. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
24. Figure 9
14. Remove the alternator's ground cable.
15. Loosen the connections for the temperature sensors. Remove the upper and lower cooling hoses from the
secondary coolant pump.
Figure 10
View from below
1.
2.
Temperature sensor primary circuit , SE 2602
Temperature sensor secondary circuit, SE 2601
16. Remove the secondary pump.
17. Loosen the hoses for the expansion tank. Unplug the level sensor's connector SE 2603 down on the expansion
tank. Loosen the four bolts for the foot step and lift it away.
Figure 11