UIT-01.PDF
•
0 likes•121 views
This document summarizes a student project to design a human-powered vehicle. It was mentored by Professor Alka Bani Agarwal and completed by student Harinarayan Vishwakarma over 7 months from June 2014 to February 2015. The project aimed to create a vehicle powered solely by human effort to address fuel scarcity. The vehicle uses levers and a chain linkage system to transmit power from pedaling to the wheels. Some advantages are health benefits, low cost, and minimal maintenance requirements. The project supported reducing carbon emissions from fuel-powered vehicles.
Report
Share
Report
Share
Download to read offline
![UNTVERSITY INSTITUTE OF TECHNOLOGY
RAJIV GANDHI PROT]DYOGIKI VISHWAVIDYALAYA
AIRPORT ROAD, BHOPAL - 462433
Phone: A7 55- 267 8812" 267 8819
Prof. Alka Bani Agarwal
Professor, Dept of Mechanical Er
UIT-RGPV, Bhopal
alk_agrll@yahoo.in
Office -A755-26788rc
Name of the Project:
Name of the Mentor:
StudentName:
CERTIF'ICATE
Improving Efficiency of Air Compressor in a Gun Carriage Factory
Prof. Alka Bani Agarwal, Mechanical Department,
UIT-RGPV, Bhopal.
Harinarayan Vishwakarma, UIT-RGPV, Bhopal.
This project was directed towards the improving efficiency of an air compressor in a gun
carriage factory. Practically, every industy, worldwide depends on compressed air in varying
degrees to support one or more of its process improving the efficiency of the air compressor
system increases the overall output.
The core idea of the project is to improve efficiency of an air compressor in a gun carriage
factory, For this project the Gun Carriage Factory at Jabalpur was taken under consideration.
Some of the observations recorded to that can increase air compressor system efficiency are: use
of after cooler and dryer in air compressor, use of PPCH pipes which are specially designed for
pneumatic system, use of calibrated gauges and leakage detectors, use of water softening plant.
On successful implementation of the above steps in pneumatic system the results showed a
significant increase in the air compressor unit efficiency.
Furthermore, the project work and the literatrne $rvey was supported and assisted by Mr. Vivek
Sharm4 I.O.F.S, Gun Carriage Factory, Jabalprr, Madhya Pradesh and Mr. Ajay Ghosh,
Coordinator of Air compression system in Gun Carriage Factory, Jabalpur, Madhya Pradesh. The](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7)
Recommended
Harish Mohan
Harish Mohan T has experience in rural development, mechanical design, project engineering, and HVAC site work. Currently, he works as a Rural Development Engineer at AMMACHI Labs, where he travels to rural villages in India to understand problems, organize discussions on issues like sanitation and skills training, and design solutions. Previously he has worked as a Mechanical Design Engineer developing training simulators, a balance trainer, and on biomass stove designs. He holds a Master's in Industrial Pollution Control and Bachelor's in Mechanical Engineering. His technical skills include CAD software and he has filed one patent.
world's best resume format
Nilesh Kumar Choubey is seeking an entry-level position utilizing his Bachelor's degree in Automobile Engineering from IEC College of Engineering & Technology. He has strong communication, collaboration, and interpersonal skills, and can quickly grasp new technical concepts. For his final year academic project, he worked on a 3-axis pneumatic hydraulic dumper using a battery, chain-sprocket, solenoid valves, and pressure regulator to lift and rotate a hydraulic piston. He also contributed to an air-operated vehicle project in college involving compressing ambient air for engine movement. Nilesh is proficient in AUTOCAD, CAD/CAM, MS Office, and has interests in music, spiritual readings, and
Resume
Phillip Bower is a mechanical engineering student at Purdue University seeking a full-time position in aerospace design. He has relevant experience as an intern at Newell Rubbermaid designing CAD assemblies for a new product and at Weber Metals implementing Six Sigma policies. At Purdue, Phillip has led teams for the Purdue AgBOT competition, the ASME Rube Goldberg team, and an automatic tour guide project for the disabled. He has strong skills in CAD programs like Creo and CATIA as well as design, manufacturing, and leadership experience.
AYON ROY (1) - Copy
This document is a resume for Ayon Roy providing personal and educational details. It summarizes that Ayon Roy has a Bachelor of Technology degree in Chemical Engineering from Heritage Institute of Technology and is seeking employment. Additional details include his date of birth, languages spoken, hobbies, and a project on lipase catalyzed hydrolysis of castor oil using organic solvents.
Nikeeta patil resume.docx0
This document contains the resume of Nikeeta Patil. It summarizes her contact information, objective of seeking a position at P&G, educational qualifications including a Master's degree from Lamar University and Bachelor's degree from Dr. B R Ambedkar Marathwada University, projects undertaken during her studies including evaluating the impact of messaging app design on user satisfaction and studying transactions and business processes in SAP, certifications earned in Lean Six Sigma and CAD software, presentations delivered at conferences, and soft skills and personal qualities like leadership, planning, and teamwork.
Nikeeta patil resume.docx0
Nikeeta Patil is seeking a position that allows her to contribute effectively to an organization's goals. She has a Master's degree in Industrial Engineering from Lamar University and a Bachelor's degree in Mechanical Engineering. Some of her projects include evaluating the impact of messaging app design on user satisfaction and studying transactions and business processes in SAP. She is Lean Green Belt certified and proficient in CAD, SAP, and Microsoft Office software. Her skills include planning, organizing, leadership, and being a team player.
UIT.PDF
This certificate summarizes Harinarayan Vishwakarma's work on "The 800cc Motorbike Project" under the guidance of Dr. Aseem Chandra Tiwari at University Institute of Technology. It certifies that Harinarayan completed the project from May 22, 2012 to August 12, 2012, which involved designing and building a motorbike using the engine of a Maruti Omni van. The project demonstrated Harinarayan's innovative thinking, research skills, and ability to complete engineering projects.
CV_Mohit Upadhyay
I am a Petroleum Engineering graduate with an open mind and adaptive attitude, willing to utilise the acquired knowledge and skills towards effective growth in the Oil and Gas industry.
Recommended
Harish Mohan
Harish Mohan T has experience in rural development, mechanical design, project engineering, and HVAC site work. Currently, he works as a Rural Development Engineer at AMMACHI Labs, where he travels to rural villages in India to understand problems, organize discussions on issues like sanitation and skills training, and design solutions. Previously he has worked as a Mechanical Design Engineer developing training simulators, a balance trainer, and on biomass stove designs. He holds a Master's in Industrial Pollution Control and Bachelor's in Mechanical Engineering. His technical skills include CAD software and he has filed one patent.
world's best resume format
Nilesh Kumar Choubey is seeking an entry-level position utilizing his Bachelor's degree in Automobile Engineering from IEC College of Engineering & Technology. He has strong communication, collaboration, and interpersonal skills, and can quickly grasp new technical concepts. For his final year academic project, he worked on a 3-axis pneumatic hydraulic dumper using a battery, chain-sprocket, solenoid valves, and pressure regulator to lift and rotate a hydraulic piston. He also contributed to an air-operated vehicle project in college involving compressing ambient air for engine movement. Nilesh is proficient in AUTOCAD, CAD/CAM, MS Office, and has interests in music, spiritual readings, and
Resume
Phillip Bower is a mechanical engineering student at Purdue University seeking a full-time position in aerospace design. He has relevant experience as an intern at Newell Rubbermaid designing CAD assemblies for a new product and at Weber Metals implementing Six Sigma policies. At Purdue, Phillip has led teams for the Purdue AgBOT competition, the ASME Rube Goldberg team, and an automatic tour guide project for the disabled. He has strong skills in CAD programs like Creo and CATIA as well as design, manufacturing, and leadership experience.
AYON ROY (1) - Copy
This document is a resume for Ayon Roy providing personal and educational details. It summarizes that Ayon Roy has a Bachelor of Technology degree in Chemical Engineering from Heritage Institute of Technology and is seeking employment. Additional details include his date of birth, languages spoken, hobbies, and a project on lipase catalyzed hydrolysis of castor oil using organic solvents.
Nikeeta patil resume.docx0
This document contains the resume of Nikeeta Patil. It summarizes her contact information, objective of seeking a position at P&G, educational qualifications including a Master's degree from Lamar University and Bachelor's degree from Dr. B R Ambedkar Marathwada University, projects undertaken during her studies including evaluating the impact of messaging app design on user satisfaction and studying transactions and business processes in SAP, certifications earned in Lean Six Sigma and CAD software, presentations delivered at conferences, and soft skills and personal qualities like leadership, planning, and teamwork.
Nikeeta patil resume.docx0
Nikeeta Patil is seeking a position that allows her to contribute effectively to an organization's goals. She has a Master's degree in Industrial Engineering from Lamar University and a Bachelor's degree in Mechanical Engineering. Some of her projects include evaluating the impact of messaging app design on user satisfaction and studying transactions and business processes in SAP. She is Lean Green Belt certified and proficient in CAD, SAP, and Microsoft Office software. Her skills include planning, organizing, leadership, and being a team player.
UIT.PDF
This certificate summarizes Harinarayan Vishwakarma's work on "The 800cc Motorbike Project" under the guidance of Dr. Aseem Chandra Tiwari at University Institute of Technology. It certifies that Harinarayan completed the project from May 22, 2012 to August 12, 2012, which involved designing and building a motorbike using the engine of a Maruti Omni van. The project demonstrated Harinarayan's innovative thinking, research skills, and ability to complete engineering projects.
CV_Mohit Upadhyay
I am a Petroleum Engineering graduate with an open mind and adaptive attitude, willing to utilise the acquired knowledge and skills towards effective growth in the Oil and Gas industry.
FDP BEOHURE_merged.pdf
This document announces a 6-day faculty development program on hydrogen hybrid technology for cleaner mobility revolution to be held from November 6-11, 2023 at BMS Institute of Technology and Management in Bengaluru, India. The program is sponsored by AICTE Training and Learning Academy and aims to impart knowledge on hydrogen fuel production, storage, and use in internal combustion engines. It will cover analytical and experimental methods for studying hydrogen fuels as well as their application in automobiles to reduce emissions. The program is open to faculty from AICTE approved institutions and will provide a certificate upon completion of assessments including attendance, participation, exams, article summaries, and projects.
resume
Rui Yao is seeking a full-time engineering position starting in 2015 utilizing his chemical engineering degree and skills. He has a B.S. in Chemical Engineering from The Ohio State University with a 3.02 GPA. His internship experience includes working as an Associate Product Engineer at SK&F of GlaxoSmithKline in China where he conducted production planning, safety inspections, sieve analysis, and product quality analysis. Rui is fluent in English and Chinese and has experience using MATLAB, CHEMCAD, COMSOL, SolidWorks, and JMP. His academic projects include senior design projects testing adhesive films and unit operation experiments in liquid-liquid extraction and mixing.
A review of application of some product development technoques applied in eng...
Abstract
New product development is always challenging and creative task in today’s era of globalization. Various internal and external factors are to be considered in the entire product development process. The concerned internal factors are skilled workforce with the organization, Budgetary provision for new product development, infrastructural and other resources available with organizations etc. While the external factors are requirement of the Customers, legal issues, Government policies, market segments and prevailing situations in the market. Considering the complexity in the product development process various new techniques of product development are being introduced by the industries, as well as proposed by researchers and academia. Lean product development, Quality Function Deployment, Six sigma is some of the techniques. In recent years there is a new technique being opted by the industry called as Advanced Product Quality Planning (APQP) .This paper is an attempt to review the developments of APQP and efforts being taken by the researchers in the development of APQP.
Keywords:-APQP, Six sigma, QFD, NPD techniques, APQP methodology, advantages of APQP
Energy Audit A Case Study of Pashupati Candle filter Udhyog And Country foo...
Energy itself is growing issue at present scenario and its effective management has growing scope in the field of industrialization. As Industrial Engineer, we must have sound knowledge of energy management, which would be integral part when we enter the field of our engineering. This is the main reason behind selection of “Energy Audit”. The project is supervised by Er. Bhisma Pandit(senior energy expert) and audit instrument support from Thapathali Campus and IEMP. The project is carried with permission in Pashupati Filter Candle Udhyog (LPG LPG Regulator Division)and Country foods Pvt.Ltd.
Soumyadeep Mukhopadhyay- resume
Focused researcher and environmental consultant with a thorough approach to groundwater, wastewater and soil treatment processes. I am based in Dublin, but engaged in a number of water treatment projects in South Asia. I take pleasure in solving green technology challenges and brainstorming over new concepts. I enjoy drafting technical documents- proposals, reports, ppt and articles. I am proficient in various graphical and statistical software packages.
Currently I am doing a Masters in Natural Resource Economics and Policy from NUI Galway, Ireland. Econometric modelling, data analysis and cost-benefit evaluations are the topics that I am most curious about. I am always looking for new opportunities in the field of environmental management involving stakeholder engagement.
EGREEN Project Implementation in Tishreen University
The document discusses the EGREEN project and Tishreen University's involvement. It notes that Tishreen University will prepare and translate two environmental engineering courses into Arabic as part of the project. It also lists the 12 teaching modules that were approved for development through the project, which aim to add new courses on topics like water resources, wastewater treatment, and renewable energy to university programs.
Design Engineering Report on Renewable energy resources.
The document discusses renewable energy resources and provides an overview of various canvases used in the project. It describes the empathy mapping canvas which identifies users like plants and industries, stakeholders like domestic and transportation sectors, and activities related to renewable energy. It also outlines the AEIOU summary canvas covering users, activities, environment, interactions, and objects involved. The project aims to promote the use of renewable resources and energy.
Resume - Mechanical Engineer
If you want to know what I did, that's all here.......... But if you want to know what can I do... HIRE me
Rana_CV-1.docx Final
Vishal Rana has a B-Tech in Mechanical and Automotive Engineering from Delhi Technological University with over 60% marks. He has work experience from internships at Tata Steel, Mercedes Benz, and educational projects related to biodiesel extraction methods and engine emissions reduction. His positions of responsibility include president of the DTU student association and organizing various technical festivals and events with large participation. He also has experience managing a startup and leading extracurricular activities in school.
PPT on Regenerative E- Bicycle
The main aim of this ppt is to make more reliable and cheaper transportation for everyone.
Cost of convectional fuel is increasing rapidly.
Depletion of Fossil fuel is also the serious concern.
Now a days pollution level is reaching the peak level.
This ppt is not only for prototype purpose, it has an practical application. The depletion of fossil fuels and increasing level of pollution leads to find out the other alternatives.
this ppt based on my final year Engineering project.
John Karam Resume
John Karam Adly Georgy is seeking an opportunity as an Industrial Engineer. He has a Master's degree in Mechanical Engineering from AUC with a GPA of 3.4. His experience includes working as a Mechanical Design and Industrial Engineer at ITALTECH, where he was responsible for 3D modeling, drawings, scheduling, and coaching technicians. He also had internships at GE analyzing oil pumping systems and at Schlumberger taking training in simulation software. His skills include fluency in English and Arabic, proficiency in AutoCAD and other engineering software.
shakil cv
Md. Shuaib Arefin is seeking a career that utilizes his knowledge and skills. He has a Bachelor of Science degree in Mechanical Engineering from Ahsanullah University of Science and Technology with a GPA of 3.10. He has participated in several extracurricular activities including robotics clubs and has worked on projects involving renewable energy and robotics. He has work experience as an intern and part-time jobs in automotive and engineering fields.
Project report 1
This document is a project report on increasing the efficiency of gas stoves carried out by four students at Sahyadri College of Engineering and Management under the guidance of Mr. Hanumanthraya R. The report details the students' work on improving stove efficiency by replacing a conventional stove stand with a newly fabricated stand. It includes sections on introduction, literature review, methodology, advantages, limitations, conclusion, suggestions for future work, and references. The goal of the project was to explore ways to improve the efficiency and emissions of existing LPG cooking stoves given limited fossil fuel resources and environmental concerns.
NARAYANASETTI SURYA KUMAR-CV
This curriculum vitae summarizes the qualifications and experience of Surya Kumar Narayanasetti. He has a PGDC from the National Power Training Institute and a B.E. in Electrical Engineering. He has over 3 years of work experience in transmission line maintenance and substation work. His skills include planning, project execution, project management, transmission line surveys, and maintenance of transmission and distribution lines. He is currently working at Ramelex Pvt Ltd conducting thermovision scanning and string replacement work.
manoj kumar 17
This document contains a summary of K. Manoj Kumar's career objective, qualifications, experience, skills, and activities. It includes his contact information, academic qualifications including a B.E. in Mechanical Engineering with a 8.56 CGPA from Anna University, internship experience in purchase department at Renault Nissan, a project on a pneumatic drilling machine, publications and patents, memberships in professional organizations, workshops and training attended, achievements and awards, papers presented, extracurricular activities, and personal details.
Thesis: Fabrication of Automated Guided Vehicle (AGV)
Abstract of Project:
In the material handling industry safety has been a major consideration from the beginning and has only become more and more measured as liability and worker moral are taken into account. Ergonomics have also rewritten how employees are effected by the work they do. In current practice, the operators that works in a production line (especially in automotive plant) will have to give out their energy to manually push the trolley with an estimated weight that is nearly to 500kg. The trolley with the body frame needed to be deliver from one defined location to the next. It is believe that the current method applied is one of the effective way to bring the trolley to the next station. However, the push and pull forces that is applied to the skid or trolley with a heavy load may cause an ergonomics effects to the operators such as the Low – back Disorder (LBD). Manual material handling work has been reported contributing to a large percentage of MSDs annually. LBD is generally caused by cumulative effects of faulty body mechanics, poor posture, awkward movements and improper lifting techniques. The main objectives of this project is to fabricate an AGV by using appropriate material and process that is able to tow a trolley or skid with a load with an estimated weight of 500kg and accomplish a safe handling operations by replacing the operators with AGV. In this project, the AGV is fabricated accordingly through appropriate process such as welding, assembly and etc. This AGV responses and navigation is controlled by the microcontroller which is a device that act as the main brain. It has the ability to follow the black line as it guide path by using the IR line sensor and avoid the obstacles by using the ultrasonic sensor. The project implicates of fabrication of the hardware. AGV is, therefore, suitable for automating material handling in batch production and mixed model production.
EIA Report
Here is the checklist of documents required for environmental clearance of construction projects:
1. Form 1 - Basic project details
2. Form 1A - Detailed project information
3. Conceptual plan - Site layout, land use details, surrounding features
4. Area statement - Permissible and proposed FAR, ground coverage, built up area
5. Site photographs
6. Water requirement details
7. Sewage treatment details - Water balance diagram, STP details
8. Solid waste management details
9. Green area details - List of trees
10. Building height and stack height details
11. Energy conservation measures
12. Fire fighting and disaster management plan
13. Environment Management Plan - Construction and
Anupkumar
Anup Kumar Doraiswamy is seeking a chemical engineering position where he can utilize his skills in process design, analysis, and optimization. He has a Master's degree in Chemical Engineering from the University of Florida with a 3.94 GPA and is expected to graduate in May 2016. His experience includes designing reactive distillation columns and separation processes using ASPEN, identifying energy losses, and simulating particle dynamics and nonlinear electrokinetics. He has strong skills in MATLAB, ASPEN Plus, and other engineering tools.
NIKHIL_PATIL-1
Nikhil Patil is applying for a trainee engineer position. He has a B.E. in Mechanical Engineering from Dr. J. J. Magdum College of Engineering with first class grades. As a student, he worked on a unique project to measure pipe flow velocity using a pitot tube that was implemented at his college. He is seeking a challenging job that allows him to apply his skills and experience.
Punamchandra rathod GCPC Biodata
Mr. Punamchandra rathod working as Senior Project Engineer (Chemical Engineer) in Gujarat Cleaner Production Centre (GCPC), also holding charge of Programme Officer, Environment Information System (GCPC-ENVIS), Ministry of Environment, Forest and Climate Change, Government of India, works to support State Government to improve overall environmental performance solving various environmental issues related to different industrial estates, supporting in preparing state industrial policy to enhance the technical and environmental infrastructure of estates, to scale up and mainstream Resource Efficiency and Cleaner Production in industries in industrial parks and retrofitting the existing estates into the eco / green industrial park and research/promotion / propagation of pollution prevention / cleaner production in academic institutions.
Expertise in Resource Efficiency and Cleaner Production, Eco industrial Park expert, Circular Economy, Waste Management, Environmental policy framework, Environment Management System, Industrial Symbiosis - waste exchange network etc
More Related Content
Similar to UIT-01.PDF
FDP BEOHURE_merged.pdf
This document announces a 6-day faculty development program on hydrogen hybrid technology for cleaner mobility revolution to be held from November 6-11, 2023 at BMS Institute of Technology and Management in Bengaluru, India. The program is sponsored by AICTE Training and Learning Academy and aims to impart knowledge on hydrogen fuel production, storage, and use in internal combustion engines. It will cover analytical and experimental methods for studying hydrogen fuels as well as their application in automobiles to reduce emissions. The program is open to faculty from AICTE approved institutions and will provide a certificate upon completion of assessments including attendance, participation, exams, article summaries, and projects.
resume
Rui Yao is seeking a full-time engineering position starting in 2015 utilizing his chemical engineering degree and skills. He has a B.S. in Chemical Engineering from The Ohio State University with a 3.02 GPA. His internship experience includes working as an Associate Product Engineer at SK&F of GlaxoSmithKline in China where he conducted production planning, safety inspections, sieve analysis, and product quality analysis. Rui is fluent in English and Chinese and has experience using MATLAB, CHEMCAD, COMSOL, SolidWorks, and JMP. His academic projects include senior design projects testing adhesive films and unit operation experiments in liquid-liquid extraction and mixing.
A review of application of some product development technoques applied in eng...
Abstract
New product development is always challenging and creative task in today’s era of globalization. Various internal and external factors are to be considered in the entire product development process. The concerned internal factors are skilled workforce with the organization, Budgetary provision for new product development, infrastructural and other resources available with organizations etc. While the external factors are requirement of the Customers, legal issues, Government policies, market segments and prevailing situations in the market. Considering the complexity in the product development process various new techniques of product development are being introduced by the industries, as well as proposed by researchers and academia. Lean product development, Quality Function Deployment, Six sigma is some of the techniques. In recent years there is a new technique being opted by the industry called as Advanced Product Quality Planning (APQP) .This paper is an attempt to review the developments of APQP and efforts being taken by the researchers in the development of APQP.
Keywords:-APQP, Six sigma, QFD, NPD techniques, APQP methodology, advantages of APQP
Energy Audit A Case Study of Pashupati Candle filter Udhyog And Country foo...
Energy itself is growing issue at present scenario and its effective management has growing scope in the field of industrialization. As Industrial Engineer, we must have sound knowledge of energy management, which would be integral part when we enter the field of our engineering. This is the main reason behind selection of “Energy Audit”. The project is supervised by Er. Bhisma Pandit(senior energy expert) and audit instrument support from Thapathali Campus and IEMP. The project is carried with permission in Pashupati Filter Candle Udhyog (LPG LPG Regulator Division)and Country foods Pvt.Ltd.
Soumyadeep Mukhopadhyay- resume
Focused researcher and environmental consultant with a thorough approach to groundwater, wastewater and soil treatment processes. I am based in Dublin, but engaged in a number of water treatment projects in South Asia. I take pleasure in solving green technology challenges and brainstorming over new concepts. I enjoy drafting technical documents- proposals, reports, ppt and articles. I am proficient in various graphical and statistical software packages.
Currently I am doing a Masters in Natural Resource Economics and Policy from NUI Galway, Ireland. Econometric modelling, data analysis and cost-benefit evaluations are the topics that I am most curious about. I am always looking for new opportunities in the field of environmental management involving stakeholder engagement.
EGREEN Project Implementation in Tishreen University
The document discusses the EGREEN project and Tishreen University's involvement. It notes that Tishreen University will prepare and translate two environmental engineering courses into Arabic as part of the project. It also lists the 12 teaching modules that were approved for development through the project, which aim to add new courses on topics like water resources, wastewater treatment, and renewable energy to university programs.
Design Engineering Report on Renewable energy resources.
The document discusses renewable energy resources and provides an overview of various canvases used in the project. It describes the empathy mapping canvas which identifies users like plants and industries, stakeholders like domestic and transportation sectors, and activities related to renewable energy. It also outlines the AEIOU summary canvas covering users, activities, environment, interactions, and objects involved. The project aims to promote the use of renewable resources and energy.
Resume - Mechanical Engineer
If you want to know what I did, that's all here.......... But if you want to know what can I do... HIRE me
Rana_CV-1.docx Final
Vishal Rana has a B-Tech in Mechanical and Automotive Engineering from Delhi Technological University with over 60% marks. He has work experience from internships at Tata Steel, Mercedes Benz, and educational projects related to biodiesel extraction methods and engine emissions reduction. His positions of responsibility include president of the DTU student association and organizing various technical festivals and events with large participation. He also has experience managing a startup and leading extracurricular activities in school.
PPT on Regenerative E- Bicycle
The main aim of this ppt is to make more reliable and cheaper transportation for everyone.
Cost of convectional fuel is increasing rapidly.
Depletion of Fossil fuel is also the serious concern.
Now a days pollution level is reaching the peak level.
This ppt is not only for prototype purpose, it has an practical application. The depletion of fossil fuels and increasing level of pollution leads to find out the other alternatives.
this ppt based on my final year Engineering project.
John Karam Resume
John Karam Adly Georgy is seeking an opportunity as an Industrial Engineer. He has a Master's degree in Mechanical Engineering from AUC with a GPA of 3.4. His experience includes working as a Mechanical Design and Industrial Engineer at ITALTECH, where he was responsible for 3D modeling, drawings, scheduling, and coaching technicians. He also had internships at GE analyzing oil pumping systems and at Schlumberger taking training in simulation software. His skills include fluency in English and Arabic, proficiency in AutoCAD and other engineering software.
shakil cv
Md. Shuaib Arefin is seeking a career that utilizes his knowledge and skills. He has a Bachelor of Science degree in Mechanical Engineering from Ahsanullah University of Science and Technology with a GPA of 3.10. He has participated in several extracurricular activities including robotics clubs and has worked on projects involving renewable energy and robotics. He has work experience as an intern and part-time jobs in automotive and engineering fields.
Project report 1
This document is a project report on increasing the efficiency of gas stoves carried out by four students at Sahyadri College of Engineering and Management under the guidance of Mr. Hanumanthraya R. The report details the students' work on improving stove efficiency by replacing a conventional stove stand with a newly fabricated stand. It includes sections on introduction, literature review, methodology, advantages, limitations, conclusion, suggestions for future work, and references. The goal of the project was to explore ways to improve the efficiency and emissions of existing LPG cooking stoves given limited fossil fuel resources and environmental concerns.
NARAYANASETTI SURYA KUMAR-CV
This curriculum vitae summarizes the qualifications and experience of Surya Kumar Narayanasetti. He has a PGDC from the National Power Training Institute and a B.E. in Electrical Engineering. He has over 3 years of work experience in transmission line maintenance and substation work. His skills include planning, project execution, project management, transmission line surveys, and maintenance of transmission and distribution lines. He is currently working at Ramelex Pvt Ltd conducting thermovision scanning and string replacement work.
manoj kumar 17
This document contains a summary of K. Manoj Kumar's career objective, qualifications, experience, skills, and activities. It includes his contact information, academic qualifications including a B.E. in Mechanical Engineering with a 8.56 CGPA from Anna University, internship experience in purchase department at Renault Nissan, a project on a pneumatic drilling machine, publications and patents, memberships in professional organizations, workshops and training attended, achievements and awards, papers presented, extracurricular activities, and personal details.
Thesis: Fabrication of Automated Guided Vehicle (AGV)
Abstract of Project:
In the material handling industry safety has been a major consideration from the beginning and has only become more and more measured as liability and worker moral are taken into account. Ergonomics have also rewritten how employees are effected by the work they do. In current practice, the operators that works in a production line (especially in automotive plant) will have to give out their energy to manually push the trolley with an estimated weight that is nearly to 500kg. The trolley with the body frame needed to be deliver from one defined location to the next. It is believe that the current method applied is one of the effective way to bring the trolley to the next station. However, the push and pull forces that is applied to the skid or trolley with a heavy load may cause an ergonomics effects to the operators such as the Low – back Disorder (LBD). Manual material handling work has been reported contributing to a large percentage of MSDs annually. LBD is generally caused by cumulative effects of faulty body mechanics, poor posture, awkward movements and improper lifting techniques. The main objectives of this project is to fabricate an AGV by using appropriate material and process that is able to tow a trolley or skid with a load with an estimated weight of 500kg and accomplish a safe handling operations by replacing the operators with AGV. In this project, the AGV is fabricated accordingly through appropriate process such as welding, assembly and etc. This AGV responses and navigation is controlled by the microcontroller which is a device that act as the main brain. It has the ability to follow the black line as it guide path by using the IR line sensor and avoid the obstacles by using the ultrasonic sensor. The project implicates of fabrication of the hardware. AGV is, therefore, suitable for automating material handling in batch production and mixed model production.
EIA Report
Here is the checklist of documents required for environmental clearance of construction projects:
1. Form 1 - Basic project details
2. Form 1A - Detailed project information
3. Conceptual plan - Site layout, land use details, surrounding features
4. Area statement - Permissible and proposed FAR, ground coverage, built up area
5. Site photographs
6. Water requirement details
7. Sewage treatment details - Water balance diagram, STP details
8. Solid waste management details
9. Green area details - List of trees
10. Building height and stack height details
11. Energy conservation measures
12. Fire fighting and disaster management plan
13. Environment Management Plan - Construction and
Anupkumar
Anup Kumar Doraiswamy is seeking a chemical engineering position where he can utilize his skills in process design, analysis, and optimization. He has a Master's degree in Chemical Engineering from the University of Florida with a 3.94 GPA and is expected to graduate in May 2016. His experience includes designing reactive distillation columns and separation processes using ASPEN, identifying energy losses, and simulating particle dynamics and nonlinear electrokinetics. He has strong skills in MATLAB, ASPEN Plus, and other engineering tools.
NIKHIL_PATIL-1
Nikhil Patil is applying for a trainee engineer position. He has a B.E. in Mechanical Engineering from Dr. J. J. Magdum College of Engineering with first class grades. As a student, he worked on a unique project to measure pipe flow velocity using a pitot tube that was implemented at his college. He is seeking a challenging job that allows him to apply his skills and experience.
Punamchandra rathod GCPC Biodata
Mr. Punamchandra rathod working as Senior Project Engineer (Chemical Engineer) in Gujarat Cleaner Production Centre (GCPC), also holding charge of Programme Officer, Environment Information System (GCPC-ENVIS), Ministry of Environment, Forest and Climate Change, Government of India, works to support State Government to improve overall environmental performance solving various environmental issues related to different industrial estates, supporting in preparing state industrial policy to enhance the technical and environmental infrastructure of estates, to scale up and mainstream Resource Efficiency and Cleaner Production in industries in industrial parks and retrofitting the existing estates into the eco / green industrial park and research/promotion / propagation of pollution prevention / cleaner production in academic institutions.
Expertise in Resource Efficiency and Cleaner Production, Eco industrial Park expert, Circular Economy, Waste Management, Environmental policy framework, Environment Management System, Industrial Symbiosis - waste exchange network etc
Similar to UIT-01.PDF (20)
A review of application of some product development technoques applied in eng...
A review of application of some product development technoques applied in eng...
Energy Audit A Case Study of Pashupati Candle filter Udhyog And Country foo...
Energy Audit A Case Study of Pashupati Candle filter Udhyog And Country foo...
EGREEN Project Implementation in Tishreen University
EGREEN Project Implementation in Tishreen University
Design Engineering Report on Renewable energy resources.
Design Engineering Report on Renewable energy resources.
Thesis: Fabrication of Automated Guided Vehicle (AGV)
Thesis: Fabrication of Automated Guided Vehicle (AGV)
UIT-01.PDF
- 1. UNWERSITY INSTITUTE OF TECHNOLOGY RAJTV GANDHI PROTIDYOGIKI VISHWAVTDYALAYA AIRPORT ROAD, BHOPAL- 462433 Phone: 07 55- 267 8812 - 267 8819 Prof. Alka Bani Agarwal Pmfessor, Dept of Mechanicsl Engg. UIT-RGPV, Bhopal alk_agrl l@yahoo.in Office -0755-26788fi Name of the Project: Name of the Mentor: Student Name: Human Powered Vehicle Prof. Alka Bani Agarwal, Mechanical Departrnenf UIT-RGPV, Bhopal. lfurinarayan Vishwakarma, UIT-RGPV, Bhopal. This project was directed towards making a vehicle powered by the human efforts. Human Powered vehicle is a great solution to deal with the ever-increasing energy crisis due to scarcity of fuel resources in today's scenario. One of the most sigriificant aspect of this project is that the vehicle does not use any {rpe of fuel for its operation. The core concept of this project instigated from the idea that the human activities are overloading the affiosphere with carbon dioxide and other global warming emissions which frap heat, steadily drive up the planet's temperaftre and create significant and harmful impacts on our healttr, environment and climate. The vehicle uses torque fransmitting levers, a kinematic chain linkage. Linkage is constructed from open chains, closed chains and combination of both. The sprocket is cormected to the gears which fansmis the power to another sprocket. This second sprocket is connected to the axle through chain mechanism. The vehicle employs a Pitnan Arm Type Steering system which is operated using pin joints on the lever. Some of the advantages include health benefits, cheaper construction, Low power requirements, High speed low weight vehicle, Simple design,Independent starting and Low maintenance. Furthermore, the project was supported and assisted by hof. Nitin Shrivastava, Faculty Mechanical Department, UIT-RSfV. The project took around 7 months starting from June 2014 till February 2015. Prof. Alka Professor 1;tt'mg ''i... UIT.RGPV,
- 2. UNTVERSITY INSTITUTE OF TECHNOLOGY RAJIV GANDHI PROT]DYOGIKI VISHWAVIDYALAYA AIRPORT ROAD, BHOPAL - 462433 Phone: A7 55- 267 8812" 267 8819 Prof. Alka Bani Agarwal Professor, Dept of Mechanical Er UIT-RGPV, Bhopal alk_agrll@yahoo.in Office -A755-26788rc Name of the Project: Name of the Mentor: StudentName: CERTIF'ICATE Improving Efficiency of Air Compressor in a Gun Carriage Factory Prof. Alka Bani Agarwal, Mechanical Department, UIT-RGPV, Bhopal. Harinarayan Vishwakarma, UIT-RGPV, Bhopal. This project was directed towards the improving efficiency of an air compressor in a gun carriage factory. Practically, every industy, worldwide depends on compressed air in varying degrees to support one or more of its process improving the efficiency of the air compressor system increases the overall output. The core idea of the project is to improve efficiency of an air compressor in a gun carriage factory, For this project the Gun Carriage Factory at Jabalpur was taken under consideration. Some of the observations recorded to that can increase air compressor system efficiency are: use of after cooler and dryer in air compressor, use of PPCH pipes which are specially designed for pneumatic system, use of calibrated gauges and leakage detectors, use of water softening plant. On successful implementation of the above steps in pneumatic system the results showed a significant increase in the air compressor unit efficiency. Furthermore, the project work and the literatrne $rvey was supported and assisted by Mr. Vivek Sharm4 I.O.F.S, Gun Carriage Factory, Jabalprr, Madhya Pradesh and Mr. Ajay Ghosh, Coordinator of Air compression system in Gun Carriage Factory, Jabalpur, Madhya Pradesh. The