How to build up security service center easy？With the integrated security equipment, the security monitoring center with more than 10000 users can be built up and managed easy. There is free CMS for security management and security monitoring. From the windows browser, the system can be accesed to remote configure or monitoring. There are local network management PC software to manage local security service systems and internet network PC software to manage all security systems. The secucirty manager can assign the authority and device to identified users.

1. evas-2506 installation
instructions

2. foreword
EAVS-2506 is an alarm video integrated host using H.265
video compression. The host supports 6-way POE high-
definition network video access, and supports multiple wired
and wireless and bus defense zones. Built-in 2G/4G network
module and TCP/IP network module, dual network
communication, stable and reliable performance.
It has special functions such as high-definition monitoring,
intelligent anti-theft, two-way intercom, intelligent home
appliances, remote control, and centralized management.
It is widely used in residential areas, villas, shops, chain
supermarkets, office buildings, enterprises and institutions,
etc., to ensure the safety of personal and property in an all-
round way.

3. Product functions and features
1. communication ways:
Supports PSTN, 2G/4G, and TCP/IP network communication modes.
2. System Integration
Set video, alarm, smart home in one, one key intelligent management.
3. Connectivity
The ONVIF protocol is supported by many major brand network cameras.
4. Centralized management
IPC centralized preview, centralized video, video playback, centralized
equipment management.
5. Remote control
Supports remote control on mobile phones, PCS, ipads, and Internet Explorer.
6. Data concurrency
Two independent IP communication networks, data concurrent to both
platforms.
7. Multiple functions
Two-way intercom, motion detection, POE power supply, routing, and so on.

4. Assembly Architecture Diagram

5. Wiring diagram

6. wiring diagram

7. Wired Zone Wiring
The detector power
supply pole is
connected to
12V+, and the
negative pole is
connected to 12V-.
The signal line is
connected to Z1
and COM,
and so on.

8. Camera video cable interface
Connect the
camera
video cable
to the 8
channels of
the host.

9. host computer interface
When setting up
programming, use a
VGA cable or HDMI
cable to connect to the
host terminal, and you
can enter the host
computer configuration
page for configuration.

10. External antenna, wired siren,
keyboard interface
The antenna is
connected to the
ANT interface, the
positive pole of the
siren Z is
connected to BEL,
and the negative
pole is connected
to GND
The keyboard is
connected
according to the
picture

11. Network cable interface, USB
interface
Connect the host
network port to the
user router with a
network cable.
USB port can
connect mouse and
U disk

12. telephone line interface
The outside line of
the telephone is
connected to the
LINE port, and the
telephone is
connected to the
TEL port.

13. Configure page settings
After the main unit is powered on and connected to the computer, you
can see the picture above

14. Configure page settings
Main page icon function introduction

15. Configure page settings
• Main page icon function introduction

16. Configure page settings
After the host is turned on, click the screen button,
and the login page shown above will be displayed. The
account admin has no password. direct login

17. Configure page settings
After logging in, the above page appears, we only need to
set system settings, security settings, network settings.

18. Configure page settings
Including: basic settings, user settings, hard disk settings, default settings,
system operation, system maintenance

19. Configure page settings
In the system settings, the basic settings can set the content on the
picture, and the factory default can also be used.

20. Configure page settings

21. Configure page settings
In the hard disk setting, the new hard disk needs to be formatted before
recording

22. Configure page settings

23. Configure page settings
The system operation force can shut down, restart and upgrade the system.

24. Configure page settings
In the system maintenance, you can set the date and time for the host to
automatically restart.

25. Configure page settings
Including: remote control setting, zone setting, system setting, telephone
alarm, user phone, password, GPRS setting

26. ID is the unique code of the wireless device, which can be directly input or
obtained wirelessly. This machine supports 8 remote controls at the same
time.
Username is the user of this remote, can be empty
Wireless siren code pairing: Turn on the siren receiver, press and hold the
save button on the wireless alarm, and click the wireless siren code pairing on
the interface. Hearing the prompt sound means that the learning is
successful. When deleting, press the Delete 1 and Delete 2 buttons
simultaneously for 1 minute.

27. Defense zone number: wireless defense zone 1-32, bus defense zone 33-96,
wired defense zone 97-105
Type: Burglar, Delay, Emergency, 24 Hours, Fire, Disabled
Defense zone address: the location where the defense zone is installed, it can
be empty
Siren Tone: When the defense zone alarms, what form will the siren use to
alarm, divided into continuous tone, pulse tone and mute
Enable: To use this defense zone, tick Enable

28. Configure page settings
Zone alarm type: refers to the type of alarm that the detector set in the zone
can report to the host computer and the alarm center after encountering an
alarm. Once the alarm is activated in the defense zone, it will send a report
message to the center according to the previously set alarm situation. In
addition, once the alarm type of a defense zone is set, no matter what kind
of alarm triggers the alarm, it will alarm according to the alarm type set in
the defense zone.
√ indicates that the host generates an alarm when the alarm is triggered.
× means that the host does not generate an alarm when the alarm is triggered,
the wireless defense zone is valid by default, and the wired defense zone is
disabled
The siren sound can be set according to the needs. It is recommended to use
different siren sounds for different alarm situations. For example, emergency
can be set to mute

29. Configure page settings
Click the wireless code pairing with the mouse to enter the
code pairing interface: when the code pairing is
successful, the following interface will appear

30. Configure page settings
Associated defense zone: In order to prevent false alarms, associate
two ringing detectors as needed. When two detectors are triggered
within the set time range, the controller will alarm, and only one
defense zone will be triggered, and the defense zone will be
activated. early warning
Note: The Associated Equipment Department recommends the use
of door magnetic switch detectors.

31. Configure page settings
System settings: You can set the delay time of arming and disarming, siren
time, and tick the arming and disarming report. Others can be set by
themselves as needed.

32. Configure page settings
Because we use the network transmission here, the alarm center telephone
alarm and user telephone can not be set

33. Configure page settings
Under alarm linkage, select the defense zone and the
corresponding camera channel to be set and click save

34. Configure page settings
Set it as needed, tick it when the timing time is valid

35. Configure page settings
Remote control/defense zone query: check how many remote controls are
connected to the host and the use of defense zones

36. Configure page settings
System alarm: no need to set if this function is not used

37. Configure page settings
Electrical switch: Used to control smart home products

38. Configure page settings
Including: encoding setting, recording setting, PTZ setting, video blocking,
color timing setting, rotation training display setting

39. Configure page settings
The encoding can be set by default, and the format can also be set
according to the needs: the code stream 960H is the highest. The picture
quality is divided into best, good, good, average, and poor. Frame number
1-25 can be adjusted by itself. The higher the frame rate, the better the
picture, the highest bit is 25fps.

40. Configure page settings
It is necessary to tick the video after the timing is valid. PTZ settings, video
occlusion, color timing settings, and rotation training settings are currently
not used and no settings are required.

41. Configure page settings
Including: basic settings, advanced settings, network time synchronization,
IP filtering, platform settings

42. Configure page settings
Tick the following IP address, fill in the IP address according to the customer
route, subnet mask: 255.255.255.0
Gateways route addresses for clients. First, enter the WAN port of the
customer router with the standby DNS. The mac address and port settings
do not need to be set.

43. Configure page settings
Platform settings: main alarm platform address: 119.147.144.84
Main alarm platform port: 7974
ID: It is the 8-digit number of the mainframe, and the number segment can be
freely edited according to the company's issued one, but other people's
number segments cannot be used.
Password: 12345678 is the password of the host and also the login password
of the customer's mobile phone client. It is best to unify it as 12345678.