The document describes the Secced MiniJib ENG4 camera jib. It has a maximum height of 3.1 meters and allows remote control of the pan-tilt head. It fits in two hard cases and provides more range of motion than a normal tripod. The remote control allows operators to get shots that would be difficult to get otherwise. Setup takes only 20 minutes and the jib has brakes to ensure safety. It is compatible with ENG cameras from Canon or Fujinon.

1. The Secced MiniJib ENG4 is a camera jib with 3.1 m / 10.2 ft max. height, complete remote control for pan-
tilt head, and for ENG cameras with Canon or Fujinon lens. The Secced mini traveler camera jib main
components are Jib arm, PancTilt Remote Head, Controllers (control box and remote control bars for head
and camera), Tripod and Dolly. The complete mini traveler jib set fits into two hard cases, one larger roller
case and smaller suitcase.
Contrast to normal tripod system, Mini Traveler provides more range of motion. Since it adopts rear
remote operation, it helps operators complete some sequence which front-operated jib cannot accomplish.
For instance, booming jib and shot from very high point which ordinary people hardly reach. Moreover, due
to restriction of terrain and other factors, camera men are not able to do front-operation, such as no
terrain underneath the front of jib, but the remote control from rear of Mini Traveler gives an outstanding
solution to this circumstance.
Pan and tilt brakes ensure safety of the jib. Easy setup, one man can finish installation in just 20 minutes.
Remote Control
Slip ring installed for pan movement allows remote head could pan unlimited. The HD signal can go through
the slip ring, with means the remote head can output HD signal. Remote head has max. payload of 15 kg.,
so it is compatible with ENG camera with either Canon or Fujinon lens. Pan and tilt movement of remote
head can be controlled, in addition the speed and damp of pan and tilt movement can be adjusted as well.
In ENG mode, pan and tilt movement of remote head can be controlled, in addition the speed and damp of
pan and tilt movement can be adjusted as well. The ENG controller of the Secced Mini Traveler Jib has the
function of start/stop recording of ENG cameras and can control zoom/focus/iris of the interchangeable
Canon or Fujinon lenses.
The equipped V-mount interface for battery make the crane work in the circumstance of no external power
source available.
Control System Configuration
• ENG Camera Controller
• Remote Head Controller
• Remote Head
• Control Box
• Main Cable
• Pan/Tilt Motor

2. Remote head Specification Remote Control
• Max. Payload: 15 kg / 33 lbs • DV Camera Controller - Secced JIB6-ENG Bar
• Max. Speed: 360° in 5 sec • Remote Head Controller - Secced JIB6 Head Bar
• Min. Speed: 360° in 8 min • Remote Head
• Tilt Range: ±720° • Control Box
• Pan Range: Unlimited • Lens Motor Kit - Secced JIB6-02
• Head Weight: 4.64 kg / 10.23 lbs • Lens Control Cable - Secced JIB6-12
Crane Specification • Zoom Adaptor Cable - Secced JIB6-12
• Total Length: 3.19 m / 10.46 ft • Main cable - Secced JIB6-10
• Max. Lens Height: 3.11 m / 10.2 ft • Pan/Tilt Motor - Secced JIB6-01
• Min. Lens Height: -0.09 m / -0.29 ft • Bounding Strap - Secced JIB6-20
• Reach: 2.4 m / 7.8 ft • Screws for Pan/Tilt Motor - Secced JIB6-21
• Tilt Range: -50° / 53° • AC/DC Cables, Adaptor
• Max. Payload: 45 kg / 99 lbs Crane Arm
• Dolly Weight: 4.8 kg / 10.6 lbs • Crane Arm with 100mm Bowl and Arm
Extension (w/screws)
• Tripod Weight: 4.2 kg / 9.3 lbs
• Central Pivot Section
• Arm Weight: 15.5 kg / 34.2 lbs
• Arm Pan/Tilt Brake
Electronic Part Specification
• Tripod
• Power input: AC 95-265V vagy DC 12-17V
(Adaptor) • Dolly w/castor
• Power output: DC 13.5V
Transportation
Transportation
• Transportation Weight: 40 kg / 88.1 lbs
• Large Hard Case (roller)
• Hard Case (suitcase)