1. 1
INDUSTRIAL TRAINING REPORT
Held At
SELLOFORM PVT. LTD.
Submitted in partial fulfilment of the
requirement for the award of the degree
Bachelor of Technology
(Mechanical Department)
Under the Supervision of
Internal Supervisor: External
Supervisor:
Mr. Praveen Chauhan Mr. Faiz Ahmed
(Assistant Professor) (QA Head)
2. SELLOFORM PRIVATE LIMITED
Submitted To :- Praveen Chauhan (Assistant Professor, Mechanical Department)
(Faculty Supervisor)
Aravali College of Engineering and Management
Jasana, Faridabad- 121102
Haryana.
External Project Guide :- Lokesh Gulati (MD SFPL) and Faiz (Senior Quality Supervisor)
Submitted By :- Praveen Kumar
University Roll No. :- 20011013511
Course :- B-Tech (Mechanical Engineering)
Batch :- 2019-2023
Semester :- 8th Semester (Final Year)
INDUSTRIAL TRAINING AT
Selloform Pvt. Ltd. Plot No. 7, Block G, Faridabad Industrial Township, sector 57, Faridabad
2
3. Table Of Content
1. Company Introduction.
2. Company’s Clients.
3. End users of SFPL’s Product.
4. Machineries using.
5. Product.
6. Quality Assurance.
7. Layout Details, Different Production Shop floors.
8. Important Terms used in Industry.
9. Conclusion.
10.References.
3
4. 1. Company Introduction
• Selloform Private Limited (SFPL) is a Private incorporated on 02 June 2021. It
is classified as Non-govt. company and is registered at Registrar of
Companies, Delhi. Its authorized share capital is Rs.2,500,000 and its paid up
capital is Rs.600,000. It is involved in Manufacture of domestic appliances.
• Directors of Selloform Private Limited are Lokesh Gulati and Pragati
Chaudhary.
• SFPL is a leading company in Wire Forming Industry.
4
5. VARIOUS TYPES OF SPRINGS VARIOUS TYPES OF BENDS
Manufacturers of all kinds of springs, wire forms, Pipe Bending,
Sheet Metal, Turned Components and Fabricated Subassemblies
5
6. Leading manufacturer of different types of springs, wire frames
and sheet metal components.
Manufacture wide range of coil springs varying from 0.15mm –
8.00mm wire dia.
Manufacture wire frames with Wire dia ranging 1.00 mm – 15.00
mm.
Manufacture sheet metal components up to sheet thickness
3.5mm (Press up to 50T)
Manufacture CNC Turned components up to dia of 25mm.
State of Art Machinery with 25 CNC (coiling/Torsion) and 15 CNC
(wire bending).
Leading Supplier for Car Seats Insert Wires
Cater to the Automotive, Electrical Industry.
6
12. 5. Product
PRODUCT RANGE
Part Part Application
1. Frame Wires
2. Duly Welded Car
Seat Frames
1. Automotive Seating
Systems
1. Zig Zag Wires
2. S-Spring
1. Driver and Co-Driver
Seats in Cars
1. Bend Rods
1. Hoods in cars
2. Door Locks
12
13. PRODUCT RANGE
Part Part Application
1. Commercial Vehicle and
Tractor Seats
1. Heavy Duty Spring
2. Suspension
Spring/Shocker Spring
2. Shock Absorbers
1. Bend Pipes 1. Car Seat Sliders (Towel Bars)
2. Seat Structure Frames
3. Tubular Handlebar for EV
13
14. PRODUCT RANGE
Part Part Application
1. Wire Forms and Fabricated Subassemblies 1. Lawn Mover Gear Lever
2. Miscellaneous Subassemblies in Tractors and other
applications
3. 2 Wheeler Back Carrier, Saree Guard etc.
14
15. PRODUCT RANGE
Part Part Application
1. GARTER SPRING 1. OIL SEALS
2. Rings for Ball Joints
1. Compression Springs 1. Seat Belts
2. Clutches
3. Spark Plugs
4. Pens
5. Electrical
Contactors
6. Engines
7. Side View Mirrors
8. Filters
9. Other uses as required
15
16. PRODUCT RANGE
Part Part Application
1. EXTENSION SPRINGS
(Both German Hook
and English Hook)
1. Wiper
2. Bike Stand
3. Door Locks
4. Electrical Uses
5. Other uses as required
1. Torsion Springs
1. Locks and Latches
2. Car Seat Slide Levers
3. Electrical MCBs
4. Brakes
16
17. Export Products for Lawn Mover
Bail Handle rod
Accelerator Lever
Linkage Rod Gear Shifter Lever rod Hinge Pin for Grass Collector
17
26. POKA-YOKE :- 100% On-line Inspection and Error
Proofing for compression and torsion springs.
SPC Monitoring:- Statistical Process Control, such as online
platforms, dashboards, or reports, to share and display the
SPC charts and control rules. You can also use meetings,
forums, or workshops to discuss and analyze the SPC charts
and control rules.
26
29. 8. Important Terms and Reports used in Industry
1. NPD - New Product Development,
2. PPAP - Production Part Approval Process,
3. MTC - Mill Test Certificate,
4. PDIR - Pre-Delivery & Inspection Report,
5. NG - NOT GOOD,
6. APQP - Advanced Product Quality Planning,
7. CAPA - Corrective Action And Preventive Action
8. OPL – One Point Lesson
29
30. Some Formats we are used to maintain Quality
1. Patrol Inspection Report (PIR)
2. Setup Approval Report (SAR)
3. Sample Inspection Report (SIR)
4. Pre Dispatch Inspection Report (PDIR)
5. Deviation / Concessional Acceptance / Wavier Note
6. Corrective Action and Preventive Action (CAPA)
7. Kaizen Report
8. Final Inspection Report
9. Production Part Approval Process (PPAP)
10. One Point Lesson
30
31. Instruments And Equipment's that we are use
1. Digital Height Gauge
2. Digital Vernier Caliper
3. Digital Micrometer
4. Profile Projector
5. Coating Thickness Tester
6. Dial Gauge
7. Bevel Protector
8. Radius Gauge
9. Slip Gauge
31
32. Some Parts We Manufacture Inspection Technics
32
Fig: Process of Part no. 747-06043 Step by Step
33. 33
Fig: Part no. A39S164005
Inspection by Gauge
Fig: Part Inspection by Gauge
Fig: Part no. MSR-0137
Inspection by DHG
Fig: Part no. MSR-0002
Inspection by DHG
34. 9. Conclusion
This internship served as an excellent medium to increase my knowledge
on solving real world problems. This internship was bi- faceted,
introductory objective being understanding of industry operations related
to development of new parts latter part of my internship dedicated to
solving real world problems, which included helping me gain an
understanding of identifying and analyzing a problem in a functioning
system, isolating possible causes, reaching root cause and proposing
innovative solutions to tackle it, going through the process of analysis and
reporting helped me understand how industries function on ground every
day. I am grateful to everyone who helped me through this internship, my
learning and understanding has increased immensely.
34
