This curriculum vitae summarizes Noel M. Tabong's experience as an Instrument Technician with over 20 years of experience in electrical and instrumentation work, including 8 years of experience abroad in Saudi Arabia, Ghana, Nigeria, and Angola working on various oil, gas and power plant projects. The CV lists his extensive work history with companies like Bechtel, Daewoo, and Gulf Consolidated Contractors on commissioning, calibration and maintenance of instrumentation systems.

1. CURRICULUM VITAE
NOEL M.TABONG
Brgy. Calamay, Moncada, Tarlac Phillippines.
Email: nm2tabong@yahoo.com/nm2tabong@gmail.com
Mobile Philippines No. 00639091268291/00639308472468
APPLIED POSITION: Instrument Technician Commissioning
OBJECTIVE
To obtain a position in progressive manner where I can use my potential to the overall success
of the organization
EXPERIENCE SUMMARY
More than twenty years experience as Electrical & Instrumentation work including eight
years experience in abroad in the field works of constructions, pre-commissioning and
commissioning start up in various Saudi aramco Oil and Gas project and saline
water conversion corporation power plants in Saudi Arabia , Westmont mining
project in Ghana West Africa, Onshore Gas Development NGL Gasco in Abu Dhabi
UAE, Angola LNG in Africa, Gas to Liquid EGTL escravos Delta Nigeria, Africa. And Angola
LNG Plant in Africa .
DETAILED JOB EXPERIENCE
Name of Company : Bechtel International Corporation
Address : Soyo, Angola, Africa
Project : Angola LNG Plant
Date : March 02, 2014 To December 16, 2014
Position : Instrument &Calibration Technician (CSU)
Job Description:

2.  To perform commissioning start up activities. Support to operation maintenance
and dcs operators engineers during the proof test procedure and interlock testing for
the process. Work on vendor activities
 To perform preventive maintenance all instruments such as transmitters, control valves
and on and off valve, recorder and controller etc. repair re- calibration all instruments
abnormal condition during the plant shut down bypass certificate required.
 To perform routine maintenance installation and trouble shoot, inhibit bypass during
testing and calibration on fire gas and smoke detector. Connected on general monitors
hazard watch and fire protection panel. Check fiber optic inverter and cables.
 Installation and functional test on flow switch on eye wash and safety shower
check alarm status on control room.
 Maintained in work in as a safe efficient manner at all time according to agreed
procedure and practice. work authorization permit company required.
Name of Company : Daewoo Nigeria Limited
Address : Escravos Delta Nigeria, Africa
Project : Escravos Gas To Liquid Plant
Date : July 15, 2012 to July 16, 2013
Position : Instrument Pre-Commissioning Technician
Job Description:
 To perform pre-loop and final loop checking of all type on field instruments and local
control panel back to DCS, SIS, MMS and PLC.
 Calibration/ configuration, simulation and troubleshoot hart protocol and field bus
instruments such as transmitters control valves. Deluge, fire and gas system etc.
 Stroking on-off valve or shut down valve redundant control system and control valve.
Trouble shooting mechanical problem repair and adjustment of trouble feedback sensor
and re-calibration.
 Carry out the diagnostic foundation field bus segment test physical layer
measurement report submitted to the client.
 To perform pre-check and final check testing simulation by of vibration probe radial
and axial proximity probe, key phasor, temperature etc for steam turbine,
generator and electric motor control on MMS, HMI and PLC
 Perform final loop checking testing and plant resource management test signing
approval for loop folder with the chevron maintenance and operator
 Undertaking pre-operational testing cause and effect procedure interlocking link into
other instruments and alarm point test value and commissioning activities
 Execute work in a safe and efficient manner at all time
Name of Company : Bechtel International Company
Address : Soyo , Angola, Africa
Project : Angola Liquified Natural Gas Plant

3. Date : September 26, 2010 to September 25 2011
Position : Instrument & Calibration Technician
Job Description:
 To perform commissioning work loop checking, repair, calibration testing, configuration
of the parameter of hart and fieldbus instrument used in process variables pressure,
level, flow, temperature, vibration, transmitter, switches etc. and other monitoring
measurement. test setpoint value automatic mode and common alarm condition of
instrument on the process as per on data sheet controlled from DCS,SIS control and
PLC
 Perform functional testing of on-off valve. Calibration and configuration of contol valve
hart and foundation fieldbus. (by masoneilan, fisher dresser, flow serve, rotork etc).
System logic testing, complex loop and interlocking system associated with the PLC.
 Perform functioning testing for Start and stop and the common alarm status and
running condition of the electric motor and panel controller from safety instrumented
system (SIS) and DCS. Test cause and effect procedure. Undertaking pre-commissioning
loop checking testing activities acceptance with the clients.
 Installation of path cable and Ethernet cable on fiber optic module profibus and fiber
optic converter located from SIS/DCS. Loop checking testing and installation of fire and
gas detector, flame detector etc.
 Ensures that all instrument assets in the area .maintained in work in a safe efficient
manner at all time according to agreed procedure and practice.
Name of Company : Eastern Bechtel Co Ltd
Address : Habshan 3 Project Abu Dhabi UAE
Project : Onshore Gas Development Gasco Abu Dhabi
Date : June 7.2009 to june11, 2010
Position : Sr. Electrical & Instrument Commissioning Technician
Job Description:
 Carry out commissioning loop checking, calibration testing, repair and troubleshooting
of conventional smart hart and foundation fieldbus used in pressure, flow,
temperature, level transmitters and others instruments controller. Including of kind of
control valves and safety valve motor operated valve, damper, sefl actuator and others
gauges.
 To perform Functional and simulation testing loop test for instrument transmitters,
controller and emergency shutdown control from PLC. SIS/DCS automatic mode given
and fedback to stroking a control valve and shut down valve. Logic and liability testing of
all electric motors.
 Carry out commissioning and monitoring coming from substation of the upstream
230kv, 33kv, 11 kv and 415v switchgear into two incomer feeder with the bus tie section

4. automatic change over facilities and circuit breaker or motor and feeder management
outgoing circuit for the purpose of no break load to prevent interruption of service.
 Program and setting of different type of GE enervista multiline relays such as
469motor management relay, 750 feeder management relay, 745transformer
management relay, mm3 motor manager relay, monitoring the electrical hardwired
system and network through integrated protection control system ( IPCS) and other
electrical protective device.
 Undertaking commissioning activities trough the clients. Work at DCS control room to
monitoring the fedback on I/O signal and set point alarm set on the process face plate
test tool set and ESD cause and effect procedure.
Name of Company : Gulf Consolidated Contractor / Snamprogetti
Address : Hawiyah and khurais, Kingdom of Saudi Arabia
Project : Hawiyah LNG Recovery Plant & khurais Crude Contruct
Saudi Aramco Project
Date : February 10, 2007 to February 20, 2009.
Position : Electrical & Instrument Commissioning Technician
Job Description:
 Carry out calibration, configuration of parameter. testing operation & commissioning of
conventional smart field instrument and fieldbus foundation used in pressure, level,
flow, temperature transmitter, instrument switches, controller and other monitoring
measurement
 Perform functional testing of on-off valve calibration and configuration of deffirent type
of control valve, movs, and damper actuator. Installation of impulse tubing and
termination of wiring. Analyses instrument error code and other discrepancy reading.
 Final loop test and simulation of deffirent type of transmitters and control valve using
field communicator and simulator process calibrator to given signal and fedback from
central control room. Functional testing of cause and effect and setpoint alarm value
test for process operation
 Cable pulling, splicing and termination of fiber optic cable, testing the power loss of
fiber optic using by reflectometer, termination of Ethernet and communication cable.
 Functional testing operation pre-commissioning and commissioning for substation such
as the high, medium and low voltage switchgear, motor controller, variable frequency
drive motor, ups rectifier and battery charger. meggering and 4 stage hi-pot for cable.
 Ensure that all instrument assets in the area. maintained in a safe efficient and cost
effective manner according to agreed procedures and practice
 Obey and follow the Saudi aramco engineering for testing and pre-commissioning and
Commissioning electrical and instrument work and safety regulation.
Name of company : EEI Corporation/ TIC International Company
Address : Ghana West Africa

5. Project : Newmont Ghana, Ahapo Gold Limited
Date : December, 27 2005 to July 11 2006
Position : Electrical & Instrument Foreman
Job Description:
 To perform project quality requirement Provide and preparing the materials to be need
in the work site. to make progressive report to be submitted to my supervisor.
 Executes project safety and quality requirements, disciplinary action for violation on
project rules and regulation agreed parameter. To perform daily schedule control daily
time-in & time out of my men.
 To report variances to my supervisor for recording in the site diaries, accountable for
meeting safety, quality and daily productivity target on my area responsibility.
Accountable for the correctness of daily time roaster [time-in & time out] of my men.
 Assign located at primary and pebble crusher. Ball mill and thickener area.
Name of company : Mountain Queen Purified Water Corp.
Address : 27 Diego Silang St. Baguio city Phil.
Date : May 26, 2003 to December 06 2005
Position : Technician Maintenance
Job Description:
 Perform Installation and maintenance of submersible pump motor. Major brand
Franklin electric controlled by electrode suspended brass and induction control relay
brand b/w series 1500 over and under voltage relay, phase sequence with overload
protection liquid level instrument control, and pressure switch on tank.
 Perform Installation and maintenance of reverse osmosis system (ROS) water process
separate into different product row and soft water. Operation of main brain process 21
stages .processing by sediment carbon, resin, and ultra violet. Monitoring of level of
chlorine and salt mixing.
 Maintenance and monitoring the automatic refilling controlled by variable frequency
drive and the operation of micro automation for 5.6 anion 350 ml to 1000 ml bottle.
Maintenance and repair of ice maker and walking freezer for ice storage.
Name of company : C.S.EVA Electromechanical Services corp.
Address : FPIP STO TOMAS, BATANGAS, PHIL.
Project : Philip Morris Cigarette Phil.
Date : November 15, 2002 to April 14 2003
Position : Electrical/ Instrument HVAC
Job Description:

6.  Perform Installation of electrical and instrument work , cable pulling and termination of
cable
 Continuity checking and cable meggering insulation resistance ,functional testing and
pre-commissioning of HVAC work such as the variable air volume, air handling unit,
cooling tower chilled compressor unit, instrument transmitter, sensor and controller.
Name of company : EEI Corp./ Saudi Arabian Bechtel Co.
Address : SHOAIBA, JEDDAH, K.S.A
Project : Saline Water Conversion Corp.(Power Plant)
Date : September 03, 1999 to October 12 2002
Position : Electrical Technician Pre-commissioning Leadman
Job Description:
 Perform functional testing and energization pre-commissioning at the substation,
distribution and sub distribution (ABB). Such as medium and low voltage switchgear,
motor controller center, transformer, reactor. Voltage regulator, inverter, rectifier,
battery charger, safe ac and interface process controller.
 Carry out functional testing and energization the operation of circuit breaker connected
into two feeder incomer with interlocking to bus tie feed supply coming from two
transformer controlled by automatic transfer switch, programmable logic controller and
different type of relays using protection device.
 Perform functional testing and pre-commissioning for run test of medium and low
voltage ac induction motor and direct current motor. measuring the starting and
running current vibration and direction of the rotation and speed, winding
temperature, drive and MOV testing
 Continuity checking and meggering the cable insulation resistance, winding of motor
and transformer. Measure and inject the current leakage test voltage and hold time 4
stages using by high potential die electric hi-pot for medium voltage cable. Measuring
the contact resistance of bus bar and circuit breaker using by micro meter tester or
ducter tester.
 To assist vendor for functional testing and energization of turbine turbo generator with
the exciter. To produce power output delivering power to generator step-up
transformer is connected to synchronize to other power plant located at the sulfur
hexafluoride (SF6) and gas isolated switchyard (GIS)
Name of company : EEI Corp/ Bechtel Overseas Corp.
Address : Mauban, Quezon province, Phil.
Project : Mauban Power Plant
Date : September 12, 1998 to June 22, 1999
Position : Industrial Electrician/ Cable Splicer

7. Job Description:
 Termination of low and medium voltage cable using 3m application 3m/pst cold shrinks
sheath seal. Installation of cable gland and shroud. Termination of cathodic protection
cable and element cathode and anode. Termination of such as power, instrument, and
communication.
 Continuity checking of wiring, arrangement dressing of cable. Meggering of resistance
insulation and measuring current leakage of medium voltage using high potential
dielectric test voltage hold time 4 stages.
Name of company : EEI Corp / Mitsubishi Heavy Ind.
Address : Masinloc, Zambales, phil.
Project : Masinloc Coal Thermal Power Plant (NPC)
Date : January 05, 1997 to August 15, 1998
Position : Industrial Electrician/ Cable Splicer
Job Description:
 Termination of medium voltage single and three core polymeric insulated XLPE cable
brand Raychem. Installation of cable gland and shroud.
 Installation of bus bar coupler and bus sectionalizer for sulfur hexafluoride and gas
insulated switchyard supply output to power turbine generating plant.
 Assist to vendor for functional testing and pre- commissioning energizing the turbine
generator and exciter brushless produce power generation input to transformer.
Name of company : Anglo Watson Bottling Phil.
Address : Industrial Park Canlubang Laguna, Phil.
Date : March 12, 1996 to December 15. 1996
Position : Instrument Technician Maintenance
Job Description:
 To carry out maintenance, calibration, Repair, installation and trouble shoot smart
transmitter such as temperature, pressure, flow level and others monitoring
measurement. cleaning of leans of camera using flame detector scanner flame furnish
area and other instrument using at batching silo and conveyor for bottling processing.
 Program of different type of relay and electronic control devices programmable logic
control. Operate located from supervisory control and data acquisition system (SCADA).
Name of company : EEI Corp.
Address : LISSP Cabuyao Laguna, Phil.
Project : Philips Semiconductor Phil.

8. Date : June 05 1995 to January 12, 1996
Position : Electrical/ Instrumentation Hvac
Job Description:
 Functional testing and energization pre- commissioning of compressor chiller. Brand
York and train. Air handling unit, exhaust fan, cooler tower .damper .booster pump.
 Installation of instrument transmitter and element such as temperature. Level, pressure,
flow brand honey well and motor controller center
Name of company : Fuji-Haya Electric Corp. Phil.
Address : Canlubang , Industrial Park, Laguna Phil.
Date : January 09, 1995 to May 30 1995
Position : Electrician Technician
Job Description:
 Perform Installation and assemble of low and medium voltage switchgear. Power and
lighting panel board, motor controller center panel and different type of transformer.
Installation of metal enclosed bus indoor and outdoor. Power monitoring system and
equipment protection
 Installation of race way trunk electrical device accessories and electronic control
component. Different type of circuit breaker. Push button indicator light. Selector switch
etc.
 Installation of metering unit, voltmeter and ammeter, different type of relays, motor
controller ,protection device, bus bar,
 Functional testing of switchgears and transformers, calibration and setting program
different type of relays.
Name of company : Electronic Service Center
Address : Mayapa, Calamba, Laguna Phil.
Date : July 15, 1992 to December 15, 1994
Position : Electronic Technician
Job Description:
 Repair, testing trouble shooting servicing type of electronics appliances such as
television. Radio cassette. Stereo, and others electronic component electrical home and
industrial machine.

9. Name of company : Cindys Hamburger Corporation
Address : Claro M. Recto .Manila PHIL.
Date : March 03, 1987 to April 15, 1992
Position : Electrical Equipment Technician Maintenance
Job Description:
 Repair installation and maintenance of various electrical and electronic microprocessor
equipment operating in production for hamburger, fast food chain and bakery
manufacturing
PERSONAL DETAILS
Nationality : Filipino
Date of birth : December 28, 1964
Religion : Roman Catholic
Permanent Address : Calamay, Moncada, Tarlac. Philippines
Mobile Number : 00639091268291/00639308472468
Passport Detail
Passport no : EB3888985
Date of issue : October 18 2011
Valid up to : October 17 2016
Place of issue : DFA Pampanga
Lic. Driver No. : C1109004478
EDUCATIONAL BACKGROUND
College : FEATI University
Course : Bachelor of Science in Electronic and
Communication Engineering Undergraduate
Technical : Guzman Institute of Technology Manila
Course : Electrical Technology Graduated
Vocational : Manila Manpower Development Center
Course : Electronic Graduated
TRAINING AND SIMINARS ATTENTED
CERTIFICATE OF ATTENDANCE
Institute of Integrated Electrical Engineer of the Philippines Inc
Western Region Chapter, Saudi Arabia

10. TRAINING CERTIFICATE
Introduction to FIBER OPTICS-THEORITECAL
(Light properties, construction & purpose network, design, connector, design & test form) and
Practical Session (Fusion splicing, cable jointing, use of Optical Time Domain Reflectometer
and Drum / Reel Testing.
Conducted by: GULF CONSOLIDATED CONTRACTOR CO.LTD
OTHERS:
CERTIFICATE OF ELIGIBILITY
CIVIL SERVICE COMMISSION
ELECTRICIAN (Licensed passed)
PERSONAL PROFILE
Being a keen leaner, I am always interested in adapting to and understanding the latest
technologies of industries and plant. Honest hard working and loyal to the organization
Good communication and analytical skill.
HOBIES
Sports, reading, listening music and playing guitar
I hereby confirm that the above information is true to the best of my knowledge and
belief, looking forward to prove my abilities for challenging opportunity.
NOEL M. TABONG
Email: nm2tabong@yahoo.com
Applicant