1. PERSONAL PROFILE: ELECTRICAL ENGINEER
Ngum Denise Ambe holds a Bachelor of Technology degree (B-Tech) in Electrical
And Electronic Engineering Technology from the College of Technology,
University of Buea with a Second class Honors.
SKILLS
Industrial safety and health, safety on hazardous environment and protection
of personnel (occupational safety and health training).OSHAcademy
Measurements and instrumentations
Maintenance and repair
Record and stock keeping
Monitoring and supervision of installation/circuit/plant operation
Wiring of control/power circuit of electrical motors and Domestic wiring.
OTHER POTENTIALS
Administrative skills ( Secretarial duties and Receptionist )
ACADEMIC PROFILE
2015 -pending: Currently undergoing online studies on OSHAcademy (occupational
safety and health training) and awaiting a program certificate on professional
development on OSHA relating to industrial safety and health.
2010-2014: B-Tech Degree in Electrical and Electronic Engineering Technology
from the University of Buea, College of Technology.
2008-2010: BACC F3 from Government Technical High School Molyko Buea
2006-2008: Probatoire F3 from Government Technical High School Molyko Buea
2002-2006:CAP F3 from Modern College of Technology Tiko
NGUM DENISE AMBE
Born: 15thMay 1990
At: Douala, Cameroon
Gender: Female
Marita Status: Single
Address: P.O. Box 85 Buea
Contact: +237 677471900
+237 656280625
Emai address: ambe.ngum@yahoo.com
Nationality: Cameroonian
CURRICULUM VITAE
2. PROFESIONAL EXPERIENCE
From the 18 of May 2015 to the 15 of February 2016: JN COMPANY LTD
Douala
Positionheld: Electrical technician
Duty: Transmission and distribution,Meter installation,Wiring of electrical
installations.
From the 1st of September to the 15th October 2014: ENEO High Fuel Oil (HFO)
Limbe Thermal Plant
Position held: Electrician
Duty: - morning and mid-day routine check-up on the whole plant i.e( the Value
readings of the gen sets, value readings of Low voltage and high voltage switch gears
,switch yard measurements, level of fuel in the various tanks at the storage tank yard.
- Monitoring and supervision of the normal functioning of gen sets and other
equipment at the thermal plant for immediate attention by the maintenance
team in case of any mal-functioning.
- Isolation ,current and resistance test measurements of the plant’s equipment
carried out monthly,reparing of the electronic board of a separator unit.
- Corrective and preventive maintenance on all the electrical equipment of the
plant, e.g inspections on all the panel boards of the plant in case of a lose
connection and the separator units.
From 1stof August - 30thofSeptember 2012: Cameroon Development
Corporation (CDC)
Position held: Electrician
Duty: - Maintenance of the factory machines ( preventive and corrective maintenance)
,wiring of the control and power circuits of the motors and maintenance work that also
concerns the power system at the supply level of AES-SONEL to the CDC Tiko
factory.
- Rewinding and maintenance of electrical motors in the Factory.
- Maintenance of the telephones lines and their power circuit at the factory.
- Installation of Air conditioning units and maintenance of the units.
.
From the 29thofjuly- 31STof August 2011:AES-SONEL Maintenance Department
SONOLO Bassa Ndokoti Douala
Positionheld: Electrician
Duty: Corrective and the Preventive maintenance of the electrical equipments at the
SONOLO maintenance unit.
3. Wiring of control panel boards, one of which was the wiring of a direct online power
circuit for the control of a 3phase motor.
Maintenance of motor control panel boards.
RESEARCH EXPERIENCE
31ST August 2011:
Institution: University of Buea ,College of technology
Project for industrial experience (AES-SONEL) SONOLO Maintenance unit
Topic: functions and generalities ofelectrical generators
30th September 2012:
Institution: University of Buea, College of technology
Project for the award of an Attestation of Internship (Cameroon Development
Corporation) CDC factory Tiko.
Topic: An Internship Report: Rewinding of Electrical Motors
2012-2013:
Institution: University of Buea, College of Technology
Project:for the award of a course grade in B-tech project
Topic: Solar Induction of A Water Pump.
2011-2012:
Institution: University of Buea, College of technology
A one day field trip at the Guiness Enterprise Ndokoti Douala. For the award of a
course grade in Industrial Experience
Topic: A Report on the functioning system of the whole enterprise most especially,the
SCADA system and other parts that concerns our field of studies.
LANGUAGES
English – Very good
French- good
INTERESTS
Cooking,Computing, Drawing, Reading and research, fashion designing,
COMPUTERS SKILLS
Microsoft Word, Power Point, Computer aided design.