Our focus for this lunch and learn is an introduction to common mistakes identified in fire sizing equations for PSVs in the upstream and midstream industries. We’ll briefly touch on the assumptions in the API 521 equations for a pool fire, when not to use these equations, and the most common mistakes for vessels inside of buildings, or in areas without good drainage. We will then focus on methods where API 521 recommends for “time-dependent analysis” of fire sizing a PSV, including but not limited to:
Changes in liquid level & wetted area
Examples of how latent heat values change during a fire
Which latent heats to use from a simulator (non-obvious)
How the PSV size required significant changes during the course of a fire on a vessel
One or two software tools that are common to use in industry for fire sizing a PSV
R.J. Goodman, EHS & Operations Training Manager, XTO Energy investigated 4 separate frac tank explosions that occurred on two separate jobs. Four Explosions Occurred:
November 10, 2005 – Major County, OK (2 Events)
March 31, 2006 – Major County, OK
April 3, 2006 – Major County, OK
All four explosions had the following characteristics in common: An air/foam mixture was pumped down the tubing and returned up the tubing/casing annulus.
EPA Fact Sheet for Proposed Amendments to Air Regulations for the Oil and Nat...Marcellus Drilling News
An overview of the proposed new rule changes EPA is proposing to prevent air pollution from hydraulic fracturing used in the oil and gas industry. The new rule changes seek to reduce the level of volatile organic compounds the EPA says are escaping into the air around drilling operations--from well pads, compressor plants, pipelines and other industry-related activities.
Our focus for this lunch and learn is an introduction to common mistakes identified in fire sizing equations for PSVs in the upstream and midstream industries. We’ll briefly touch on the assumptions in the API 521 equations for a pool fire, when not to use these equations, and the most common mistakes for vessels inside of buildings, or in areas without good drainage. We will then focus on methods where API 521 recommends for “time-dependent analysis” of fire sizing a PSV, including but not limited to:
Changes in liquid level & wetted area
Examples of how latent heat values change during a fire
Which latent heats to use from a simulator (non-obvious)
How the PSV size required significant changes during the course of a fire on a vessel
One or two software tools that are common to use in industry for fire sizing a PSV
R.J. Goodman, EHS & Operations Training Manager, XTO Energy investigated 4 separate frac tank explosions that occurred on two separate jobs. Four Explosions Occurred:
November 10, 2005 – Major County, OK (2 Events)
March 31, 2006 – Major County, OK
April 3, 2006 – Major County, OK
All four explosions had the following characteristics in common: An air/foam mixture was pumped down the tubing and returned up the tubing/casing annulus.
EPA Fact Sheet for Proposed Amendments to Air Regulations for the Oil and Nat...Marcellus Drilling News
An overview of the proposed new rule changes EPA is proposing to prevent air pollution from hydraulic fracturing used in the oil and gas industry. The new rule changes seek to reduce the level of volatile organic compounds the EPA says are escaping into the air around drilling operations--from well pads, compressor plants, pipelines and other industry-related activities.
LNG Industry Magazine (Risk Mitigation Standards) July 2016Joe Hughes
Experience has demonstrated that insulation systems within LNG facilities are often ‘under-designed’ when compared to other mechanical systems. Decades of lessons learned from
under-designing other mechanical systems, such as piping materials, welding, compressors, relief valves, etc., have led to a keen awareness among LNG engineers regarding impacts on safety, plant reliability, process efficiency, energy loss, and
environmental compliance.
The purpose of this article is to offer a macro-level discussion
of the following:The role of standards in mitigating insulation risks. Which standards are becoming dominant for LNG insulation. Where standards must be supplemented with broader risk mitigation.
LNG Industry Magazine (Risk Mitigation Standards) July 2016Dyplast Products
Experience has demonstrated that insulation systems within LNG facilities are often ‘under-designed’ when compared to other mechanical systems. Decades of lessons learned from
under-designing other mechanical systems, such as piping materials, welding, compressors, relief valves, etc., have led to a keen awareness among LNG engineers regarding impacts on safety, plant reliability, process efficiency, energy loss, and
environmental compliance.
The purpose of this article is to offer a macro-level discussion
of the following:The role of standards in mitigating insulation risks. Which standards are becoming dominant for LNG insulation. Where standards must be supplemented with broader risk mitigation.
V 1 presentation on safety aspects of lpg handling and storageImran Bokhari
Liquefied Petroleum Gas (LPG) is a mixture of Propane and Butanes, with Propane content of 30 to 60 percent and Butanes content of 40 to 70 percent. LPG can exist in liquid state at moderate pressure at ambient temperature. It is colorless, odorless, highly volatile and heavier than air (even at ambient conditions) substance. It easily forms combustible/explosive mixture when released in air, thus posing unique safety issues. Besides being a combustible substance posing fire hazard, LPG due to its nature also poses threats of cold burns and suffocation. LPG is being extensively used as fuel in homes, restaurants, transportation and some industries. In this presentation we have discussed in detail a major HSE related incident that have occurred in the past and mitigation strategies for the same. The required safety devices and their engineering design features in LPG extraction plant to avoid accidents are also discussed.
These interim guidelines are provided for RESNET Building Performance Auditors(BPAs) or Comprehensive HERS Raters (CHERS Raters) who have been trained by a RESNET-accredited Training Provider on these protocols. These guidelines shall befollowed by RESNET-accredited Raters and Auditors (hereinafter referred to collectively as “Auditors”) performing combustion appliance testing or writing work scopes forrepairs. If the Auditor has been trained and certified in accordance with a RESNET approved “equivalent home performance certification program” or the Building Performance Institute (BPI) Standards, the Auditor may follow protocols in accordance with those equivalent standards.
Gas Technology Institute & Kwik Trip - Station Installation Guidelines for CNGWisconsin Clean Cities
Are you interested in the station installation guidelines for CNG? Learn about the basics guidelines, processes, and experiences of installing a CNG station.
Key Process Considerations for Pipeline Design BasisVijay Sarathy
Prior to venturing into an oil & gas pipeline project, the project team would require a design basis, based on which the project is to proceed. Oil & Gas Pipeline design begins with a route survey including engineering & environmental assessments. The following document provides a few key considerations for process engineers to keep in mind, the factors that matter when preparing a pipeline design basis from a process standpoint.
RECENT AMENDMENTS TO FINAL 2012 NSPS, Climate Action Plan, EPA and Methane, 40 CFR Part 98 Subpart W – Petroleum and Natural Gas Systems, MODIFICATIONS TO GP-5
The EPA has now intervened with consent decrees with most major refiners and the normal discharge of the exhaust gas from the process to the atmosphere via the incinerator is no longer viable (they now go through a tail gas treating unit which can “block” the outlet with block valves or liquid head). There are rumors that certain facilities are going to be required to install traps in the sulfur seals that do not allow gases to pass through them (similar to a steam trap, but for sulfur). These two steps eliminate the overpressure protection for “old” SRUs. Note that wherever the emergency vent gas goes, the gas is extremely toxic, can, and has killed people. For that reason, venting via the sulfur pit is probably a bad idea as sulfur pits tends to be a buried low pressure tank with a low allowable pressure.
How to Make a Field invisible in Odoo 17Celine George
It is possible to hide or invisible some fields in odoo. Commonly using “invisible” attribute in the field definition to invisible the fields. This slide will show how to make a field invisible in odoo 17.
Biological screening of herbal drugs: Introduction and Need for
Phyto-Pharmacological Screening, New Strategies for evaluating
Natural Products, In vitro evaluation techniques for Antioxidants, Antimicrobial and Anticancer drugs. In vivo evaluation techniques
for Anti-inflammatory, Antiulcer, Anticancer, Wound healing, Antidiabetic, Hepatoprotective, Cardio protective, Diuretics and
Antifertility, Toxicity studies as per OECD guidelines
LNG Industry Magazine (Risk Mitigation Standards) July 2016Joe Hughes
Experience has demonstrated that insulation systems within LNG facilities are often ‘under-designed’ when compared to other mechanical systems. Decades of lessons learned from
under-designing other mechanical systems, such as piping materials, welding, compressors, relief valves, etc., have led to a keen awareness among LNG engineers regarding impacts on safety, plant reliability, process efficiency, energy loss, and
environmental compliance.
The purpose of this article is to offer a macro-level discussion
of the following:The role of standards in mitigating insulation risks. Which standards are becoming dominant for LNG insulation. Where standards must be supplemented with broader risk mitigation.
LNG Industry Magazine (Risk Mitigation Standards) July 2016Dyplast Products
Experience has demonstrated that insulation systems within LNG facilities are often ‘under-designed’ when compared to other mechanical systems. Decades of lessons learned from
under-designing other mechanical systems, such as piping materials, welding, compressors, relief valves, etc., have led to a keen awareness among LNG engineers regarding impacts on safety, plant reliability, process efficiency, energy loss, and
environmental compliance.
The purpose of this article is to offer a macro-level discussion
of the following:The role of standards in mitigating insulation risks. Which standards are becoming dominant for LNG insulation. Where standards must be supplemented with broader risk mitigation.
V 1 presentation on safety aspects of lpg handling and storageImran Bokhari
Liquefied Petroleum Gas (LPG) is a mixture of Propane and Butanes, with Propane content of 30 to 60 percent and Butanes content of 40 to 70 percent. LPG can exist in liquid state at moderate pressure at ambient temperature. It is colorless, odorless, highly volatile and heavier than air (even at ambient conditions) substance. It easily forms combustible/explosive mixture when released in air, thus posing unique safety issues. Besides being a combustible substance posing fire hazard, LPG due to its nature also poses threats of cold burns and suffocation. LPG is being extensively used as fuel in homes, restaurants, transportation and some industries. In this presentation we have discussed in detail a major HSE related incident that have occurred in the past and mitigation strategies for the same. The required safety devices and their engineering design features in LPG extraction plant to avoid accidents are also discussed.
These interim guidelines are provided for RESNET Building Performance Auditors(BPAs) or Comprehensive HERS Raters (CHERS Raters) who have been trained by a RESNET-accredited Training Provider on these protocols. These guidelines shall befollowed by RESNET-accredited Raters and Auditors (hereinafter referred to collectively as “Auditors”) performing combustion appliance testing or writing work scopes forrepairs. If the Auditor has been trained and certified in accordance with a RESNET approved “equivalent home performance certification program” or the Building Performance Institute (BPI) Standards, the Auditor may follow protocols in accordance with those equivalent standards.
Gas Technology Institute & Kwik Trip - Station Installation Guidelines for CNGWisconsin Clean Cities
Are you interested in the station installation guidelines for CNG? Learn about the basics guidelines, processes, and experiences of installing a CNG station.
Key Process Considerations for Pipeline Design BasisVijay Sarathy
Prior to venturing into an oil & gas pipeline project, the project team would require a design basis, based on which the project is to proceed. Oil & Gas Pipeline design begins with a route survey including engineering & environmental assessments. The following document provides a few key considerations for process engineers to keep in mind, the factors that matter when preparing a pipeline design basis from a process standpoint.
RECENT AMENDMENTS TO FINAL 2012 NSPS, Climate Action Plan, EPA and Methane, 40 CFR Part 98 Subpart W – Petroleum and Natural Gas Systems, MODIFICATIONS TO GP-5
The EPA has now intervened with consent decrees with most major refiners and the normal discharge of the exhaust gas from the process to the atmosphere via the incinerator is no longer viable (they now go through a tail gas treating unit which can “block” the outlet with block valves or liquid head). There are rumors that certain facilities are going to be required to install traps in the sulfur seals that do not allow gases to pass through them (similar to a steam trap, but for sulfur). These two steps eliminate the overpressure protection for “old” SRUs. Note that wherever the emergency vent gas goes, the gas is extremely toxic, can, and has killed people. For that reason, venting via the sulfur pit is probably a bad idea as sulfur pits tends to be a buried low pressure tank with a low allowable pressure.
How to Make a Field invisible in Odoo 17Celine George
It is possible to hide or invisible some fields in odoo. Commonly using “invisible” attribute in the field definition to invisible the fields. This slide will show how to make a field invisible in odoo 17.
Biological screening of herbal drugs: Introduction and Need for
Phyto-Pharmacological Screening, New Strategies for evaluating
Natural Products, In vitro evaluation techniques for Antioxidants, Antimicrobial and Anticancer drugs. In vivo evaluation techniques
for Anti-inflammatory, Antiulcer, Anticancer, Wound healing, Antidiabetic, Hepatoprotective, Cardio protective, Diuretics and
Antifertility, Toxicity studies as per OECD guidelines
2024.06.01 Introducing a competency framework for languag learning materials ...Sandy Millin
http://sandymillin.wordpress.com/iateflwebinar2024
Published classroom materials form the basis of syllabuses, drive teacher professional development, and have a potentially huge influence on learners, teachers and education systems. All teachers also create their own materials, whether a few sentences on a blackboard, a highly-structured fully-realised online course, or anything in between. Despite this, the knowledge and skills needed to create effective language learning materials are rarely part of teacher training, and are mostly learnt by trial and error.
Knowledge and skills frameworks, generally called competency frameworks, for ELT teachers, trainers and managers have existed for a few years now. However, until I created one for my MA dissertation, there wasn’t one drawing together what we need to know and do to be able to effectively produce language learning materials.
This webinar will introduce you to my framework, highlighting the key competencies I identified from my research. It will also show how anybody involved in language teaching (any language, not just English!), teacher training, managing schools or developing language learning materials can benefit from using the framework.
The Roman Empire A Historical Colossus.pdfkaushalkr1407
The Roman Empire, a vast and enduring power, stands as one of history's most remarkable civilizations, leaving an indelible imprint on the world. It emerged from the Roman Republic, transitioning into an imperial powerhouse under the leadership of Augustus Caesar in 27 BCE. This transformation marked the beginning of an era defined by unprecedented territorial expansion, architectural marvels, and profound cultural influence.
The empire's roots lie in the city of Rome, founded, according to legend, by Romulus in 753 BCE. Over centuries, Rome evolved from a small settlement to a formidable republic, characterized by a complex political system with elected officials and checks on power. However, internal strife, class conflicts, and military ambitions paved the way for the end of the Republic. Julius Caesar’s dictatorship and subsequent assassination in 44 BCE created a power vacuum, leading to a civil war. Octavian, later Augustus, emerged victorious, heralding the Roman Empire’s birth.
Under Augustus, the empire experienced the Pax Romana, a 200-year period of relative peace and stability. Augustus reformed the military, established efficient administrative systems, and initiated grand construction projects. The empire's borders expanded, encompassing territories from Britain to Egypt and from Spain to the Euphrates. Roman legions, renowned for their discipline and engineering prowess, secured and maintained these vast territories, building roads, fortifications, and cities that facilitated control and integration.
The Roman Empire’s society was hierarchical, with a rigid class system. At the top were the patricians, wealthy elites who held significant political power. Below them were the plebeians, free citizens with limited political influence, and the vast numbers of slaves who formed the backbone of the economy. The family unit was central, governed by the paterfamilias, the male head who held absolute authority.
Culturally, the Romans were eclectic, absorbing and adapting elements from the civilizations they encountered, particularly the Greeks. Roman art, literature, and philosophy reflected this synthesis, creating a rich cultural tapestry. Latin, the Roman language, became the lingua franca of the Western world, influencing numerous modern languages.
Roman architecture and engineering achievements were monumental. They perfected the arch, vault, and dome, constructing enduring structures like the Colosseum, Pantheon, and aqueducts. These engineering marvels not only showcased Roman ingenuity but also served practical purposes, from public entertainment to water supply.
Welcome to TechSoup New Member Orientation and Q&A (May 2024).pdfTechSoup
In this webinar you will learn how your organization can access TechSoup's wide variety of product discount and donation programs. From hardware to software, we'll give you a tour of the tools available to help your nonprofit with productivity, collaboration, financial management, donor tracking, security, and more.
Synthetic Fiber Construction in lab .pptxPavel ( NSTU)
Synthetic fiber production is a fascinating and complex field that blends chemistry, engineering, and environmental science. By understanding these aspects, students can gain a comprehensive view of synthetic fiber production, its impact on society and the environment, and the potential for future innovations. Synthetic fibers play a crucial role in modern society, impacting various aspects of daily life, industry, and the environment. ynthetic fibers are integral to modern life, offering a range of benefits from cost-effectiveness and versatility to innovative applications and performance characteristics. While they pose environmental challenges, ongoing research and development aim to create more sustainable and eco-friendly alternatives. Understanding the importance of synthetic fibers helps in appreciating their role in the economy, industry, and daily life, while also emphasizing the need for sustainable practices and innovation.
Palestine last event orientationfvgnh .pptxRaedMohamed3
An EFL lesson about the current events in Palestine. It is intended to be for intermediate students who wish to increase their listening skills through a short lesson in power point.
Macroeconomics- Movie Location
This will be used as part of your Personal Professional Portfolio once graded.
Objective:
Prepare a presentation or a paper using research, basic comparative analysis, data organization and application of economic information. You will make an informed assessment of an economic climate outside of the United States to accomplish an entertainment industry objective.
Read| The latest issue of The Challenger is here! We are thrilled to announce that our school paper has qualified for the NATIONAL SCHOOLS PRESS CONFERENCE (NSPC) 2024. Thank you for your unwavering support and trust. Dive into the stories that made us stand out!
Francesca Gottschalk - How can education support child empowerment.pptxEduSkills OECD
Francesca Gottschalk from the OECD’s Centre for Educational Research and Innovation presents at the Ask an Expert Webinar: How can education support child empowerment?
Adversarial Attention Modeling for Multi-dimensional Emotion Regression.pdf
Nfpa.58.2004 chapter 05
1.
2. As many of us are aware, tropical storm Irene left a scene
of devastation in its wake. Home’s along Connecticut’s
shore line were hit particularly hard. As seen on the nightly
news, many homes were damaged and some were even
swept away when we were hit by high winds and high
tides. Besides the problem of all the debris from these
homes and their yards a much larger safety problem has
been discovered. Large propane tanks that once fed
homes were tipped over or washed out into Long Island
sound. The environmental and safety concerns are
obvious.
3. Recently in Connecticut a Massachusetts
contractor was arrested and sentenced to two
years probation as well as being fined $20,000
arising from reckless and unlicensed
installation of piping at a 30,000 gallon North
Canaan propane facility. The court has also
prohibited him or any of his employees from
performing any work in the state for the next
two years.
4. NFPA 58 deals with the storage, use, handling
and transportation of Liquefied Petroleum Gas
only. CT currently references the 1995 edition
of NFPA 58. PSI Examinations, who conducts
the testing for the Connecticut Department of
Consumer Protection references the 2008
addition of the standard for the state test. This
standard contains 15 chapters, 12 annex and
an index.
5. Administration
Referenced Publications
Definitions
General Requirements
LP Gas Equipment and
Appliances
Installation of LP Gas
Systems
LP-Gas Liquid Transfer
Storage of Cylinders
Awaiting Use, Resale or
Exchange
Vehicular Transportation of
LP Gas
Buildings or Structures
Housing LP-Gas Distribution
Facilities
Engine Fuel Systems
Refrigerated Containers
Marine Shipping &
Receiving
Operation & Maintenance
Pipe and Tubing Sizing
Tables
6. Unlike the chapters in this
standard which are numbered,
the Annex are listed as A through
L. The index follows the last
annex.
Explanatory Material
Properties of LP-Gas
Design, Construction &
Requalification of DOT (ICC)
Cylinders
Design of ASME & API-ASME
Containers
Pressure Relief Devices
Liquid Volume Tables,
Computations & Graphs
Wall Thickness of Copper
Tubing
Procedure for Torch Fire &
Hose Stream Testing of
Thermal Insulation Systems
for LP-Gas Containers
Container Spacing
Sample Ordinance Adopting
NFPA-58
Burial & Corrosion Protection
for Underground & Mounted
ASME Containers
Informational References
Index
7. Liquefied Propane Gas more commonly
referred to as LP Gas is a flammable mixture of
hydrocarbon gases. LP gas has a verity of
uses from fuel for heating and cooking
equipment to powering vehicles. It is being
used more and more as an aerosol propellant,
it is also used as a refrigerant. Using it as a
refrigerant helps our ozone layer by replacing
harmful chlorofluorocarbons
8. There are a verity of LP gases that are
primarily propane or butane. The most
common sold is a mixture of both these gases.
An odorant, ethanethiol, is added to the gas to
aid in leak detection. Amyl ercaptan or
thiophene are two other odorants that may be
used in place of ethanethiol.
9. LP gas is made from refining natural gas and is
usually comes from fossil fuel sources
manufactured from crude oil during the refining
process. It can also be extracted from gas or
oil streams as they are taken from the ground.
LP gas burns cleanly with few sulfur emissions.
Approximately 3% of the energy consumed is
LP gas.
10. Containers come under section 5.2 of the
2008 addition of NFPA 58.
Designed, fabricated tested & marked to US
DOT and ASME Section VIII standards.
Section 7.4 of the standard addresses the
quantity of LP-gas in contains. Tables 7.4.2.2
addresses the maximum filling limit by
weight while table 7.4.2.3(a) deals with the
maximum filling weight by volume.
11. All gases are rated with a specific gravity
identification. This number relates to air which
is rated at 1. LPG has a specific gravity of 1.5
at vapor. Which means unlike natural gas,
which has a specific gravity of .6 to .7, LPG is
heavier than air and will sink rather than rise
when in it’s gaseous state.
12. As was mentioned in the previous slide, LP-
Gas, when in its gaseous state, is heavier than
air. Why is this a concern? As plumbers we
know that when working in any area that may
contain vaporous gas we must first use a sniffer
to test the atmosphere for any possible gas
leaks before we use any tool or equipment that
has and open flame or may create a spark. This
is done to protect against creating an explosion
that may occur by an open flame or spark.
13. Since natural gas has a specific gravity that is less
than that of air, this gas will rise within an atmosphere.
When we test for any natural gas that might be in the
atmosphere, we normally will test the air closer to the
ceiling. Since LP-Gas has a specific gravity heavier
than air we should be testing closer to the floor. The
mechanic should be aware of what equipment is in the
area. Although there may not be the obvious such as
furnaces, heaters or cooking appliances. Propane
powered tow motors may use the area as a path of
travel or storage. A gas leak from this equipment could
pool in an area which could have a devastating effect
if the mechanic caused a source of ignition in the
vicinity.
Be safe check before you start.
14. 3.3.13 Container: Any vessel, including
cylinders, tanks, portable tanks, and cargo
tanks, used for the transporting or storing of
LP-Gases.
3.3.16 Cylinders: A container designed,
constructed, tested, and marked in accordance
with U.S. DOT specifications, Title 49, Code of
Federal Regulations, or in accordance with a
valid DOT exemption.
15. 6.6.2.1 Cylinders shall be installed only
aboveground set upon a firm foundation or
otherwise be firmly secured. The cylinder shall
not be in contact with soil.
6.6.2.2 Flexibility shall be provided in the
connecting piping. Where flexible connectors
are used, they shall comply with 6.9.6.
16. Flexible connectors shall be installed in
accordance with the manufacturer’s
instructions.
Flexible metallic connectors shall not exceed
60” in overall length when used with liquid or
vapor piping on stationary containers of 2000
gallons water capacity or less.
17. In the next few slides we will be discussing the
installation of ASME cylinders and containers.
Do to time restrictions we will only high light
some of this information. When installing these
systems you should consult your local building
official as to the proper method. You may also
want to check OSHA section 1926.153 which
addresses Liquefied Petroleum Gas.
18. Addresses methods and regulation for supporting
containers of under 2000 gallons and over 2000
gallons. Which include…
Setting on masonry or noncombustible surface.
Saddles.
Structural steel supports.
Interconnections.
Requirements for area’s with snow depths and,
Vehicle mounting.
19. Table 6.6.3.3 lists information on,
Container Size
Attached Support and
Height of Bottom of the Container.
20. Addresses installation of vertical containers over 125
gallons.
Installed on reinforced concrete or steel structural
supports on reinforced concrete foundations that
meet 5.2.4.3.
Steel supports shall be protected against fire
exposure, w/minimum 2 hr. rating.
Vertical ASME containers used in liquid service
shall not be manifolded to horizontal ASME
containers.
Vertical ASME containers of different dimensions
shall not be manifolded together.
21. Allows for the setting of containers on paved
surfaces or firm earth for not more than 12 months.
When placed on earth the area must be cleared of
dry grass, weeds and other combustible materials
within 10’.
Flexibility in connecting piping as with 6.9.6.
Potable containers installed isolated locations
w/bottoms of skids/runners above ground be either
fire resistive or non fire resistive must meet…
› Height outside bottom of container not exceed 5’ above
the ground.
› Must have approval of Authority Having Jurisdiction.
22. When installing containers underground section
6.6.6 should be followed. This section will
address such things as minimal coverage above
the tank along with protection of fitting housing,
housing cover, container connections, and piping
against vehicular damage. Party responsibility,
abandoning a container. Partially installed
underground containers. Section 6.6.7
Installation of Containers on Roofs of
Buildings
23. Although not commonly know there are other
NFPA Standards that has some plumbing
aspects involved. They are listed on the next
side along with the which edition that the state
currently recognizes.
24. NFPA 30-1996
› Flammable & Combustible Liquids Code
(gasoline)
NFPA 30A-1996
› Automotive & Marine Service Station
NFPA 30B-1994
› Manufacturing & Storage of Aerosol
Products
NFPA 31-1992
› Installation of Oil Burning Equipment
NFPA 34-1995
› Standard for Dipping & Coating Using
Flammable Liquids
NFPA 35-1995
› Standard for the Manufacture of Organic
Coatings
NFPA 37-1994
› Installation & Use of Stationary Combustion
Engines & Turbines
NFPA 52-1992
› Natural Fuel Gas Code
NFPA 54-1996
› Compressed Natural Gas
NFPA 57-1996
› Liquefied Natural Gas Vehicles Fuel
Systems
NFPA 58-1995
› Standard for Storage & Handling of Liquid
petroleum Gasses
NFPA 395-1993
› Storage of Flammable Liquids on Farms &
Isolated Construction Projects
NFPA 401-1996
› Aircraft Fueling Services
NFPA 415
› Aircraft Fuelling Ramp Drainage