ICT Tools and Equipment

1. TVL-ICT
COMPUTER SYSTEM SERVICING
NC II
NETWORK TOOLS, MATERIALS AND EQUIPMENT
RIANNEL B. TECSON
Teacher

2. LEARNING OBJECTIVES
• Determine the range of equipment needed to build a network;
• Identify the network materials, tools and equipment; and
• Appreciate and show positive attitude towards accomplishing tasks in a group
activity.

3. REVIEW:

4. CAN YOU NAME IT?

5. FIND ME!
It is an electronic device for storing and processing data,
typically in binary form, according to instructions given to it
in a variable program.
computer

6. FIND ME!
It is a networking hardware that connects devices on a computer
network by using packet switching to receive and forward data
to the destination device.
Network Switch / Switch Hub

7. FIND ME!
It is used as Ethernet cables and telephone wires for short to
medium distances to transfer data and audio signals. They are
used for signal transfer in automation and control systems.
UTP cables

8. FIND ME!
This is a standard physical Network Interface used for connecting
telecommunications equipment commonly, a computer
networking equipment.
RJ-45 connector

9. FIND ME!
It is a tool used to join the RJ-45 connectors to
the both ends of either phone or CAT5 cable.
Crimper

10. FIND ME!
A tool designed to remove the protective covering (jacket)
off of a cable to expose the inner wires.
Wire stripper

11. FIND ME!
It is a device that is used to test the strength and
connectivity of a particular type of cable or other wired
assemblies
LAN Cable Tester

12. FIND ME!
It is a board in a switchboard, computer, or other device with
a number of electric sockets that may be connected
in various combinations.
Patch panel

13. FIND ME!
It is a supporting framework that holds hardware
modules. It typically contain patch panel, switch
and other computing equipment.
Bay Rack

14. ONCE AGAIN…
• What are the materials, tools and equipment to build a
network?
• Which devices or tools will be used to create network
cables?
• What tool will be used to test LAN cable?
• What device will be needed to connect devices to a
computer network?

15. LET’S WATCH THIS!
• What are the common network cables?
• What UTP category cable that has a data rate of up
to 1Gbps?
• What network device that is used to gather the
signals from devices that are connected to it?
• The word MODEM comes from what words?
• Which device comes in after modem?
https://youtu.be/5cnpLo7pc
tw

16. BE CONNECTED!
• What are your thoughts? Do you agree with it or not?

17. ASSESSMENT:
• Get ¼ sheet of paper.
• Write your name and date today.

18. PART I. FILL THE BLANK.
DIRECTION: WRITE THE CORRECT ANSWER IN EACH ITEM.
1. _____________ is a network switch (also called switching hub, bridging
hub, and by the IEEE MAC bridge) is networking hardware that
connects devices on a computer network by using packet switching to
receive and forward data to the destination device.
2. ______________ is a board in a switchboard, computer, or other device
with a number of electric sockets that may be connected in various
combinations.

19. PART I. FILL THE BLANK.
DIRECTION: WRITE THE CORRECT ANSWER IN EACH ITEM.
3. ____________ is a networking device that forwards data packets
between computer networks. A packet is typically forwarded from
one router to another router through the networks that
constitute an internetwork (e.g. the Internet) until it reaches its
destination node.
4. ___________ is a device that is used to test the strength and
connectivity of a particular type of cable or other wired
assemblies.

20. PART I. FILL THE BLANK.
DIRECTION: WRITE THE CORRECT ANSWER IN EACH ITEM.
5. ______________ is a standard physical Network Interface used
for connecting telecommunications equipment commonly, a
computer networking equipment.

21. PART II. ENUMERATION.
DIRECTION:
ANSWER THE FOLLOWING QUESTIONS IN SIMPLE AND COMPLETE SENTENCES. EACH
ITEM IS WORTH 5 POINTS.
1. What are the equipment, tools and materials needed
in connecting two computers using wired
connection?
2. What range of equipment do you need to build a
network?

22. ASSIGNMENT
• Bring 2 pieces of RJ-45 connectors; and
• 2-meters length of UTP cable
next meeting for the Performance Task.