This document provides a safety data sheet for Toho9000 Superb Engine Additive, which is a lubricant additive compound. It lists the product details, classification, physical/chemical properties, toxicity, exposure limits, handling/storage requirements, transportation information, and other safety information. The additive is a clear liquid with no significant hazards listed. Proper precautions like ventilation, protective equipment, and flammability controls are recommended when using or storing the product.

1. Updated on 3
rd
May 2011
M A T E R I A L S A F E T Y D A T A S H E E T
Manufacturer Information Company: TOHO UNIVERSE PTE LTD
Address: Block 3015A, Ubi Road 1,
#01-09, Singapore 408705.
Tel No: (65) 6742 2275
Fax No: (65) 6848 1175
Product Name (Chemical Name, trade name) Toho9000 Superb Engine Additive
Material Specification Classification of element/compound Compound
Chemical name Additive
Content Lubricant additive
Chemical formula or equation Not specified
CAS No. Proprietary information protection compound
UN classification and serial number Not applicable
Hazard classification Classification category: Not applicable
(primary hazardous characteristics
are followed)
Danger: Not regulated
Toxicity: Information not available
Environmental Effect: Information not available
First aid In case of contact with eyes Flush with water not less than minutes.
Require doctor consultation.
In case of contact with skin Wash affected area with soap.
Inhalation Move to fresh air area
Keep the body warm and require a
complete rest.
Consult a doctor if necessary.
Swallow Rinse mouth thoroughly with water.
Consult a doctor immediately.
Fire Emergency Response Extinguishing methods: 1. Extinguish the source of fire
2. At early stage of fire use powder or gas
extinguisher.
3. In a larger scale fire, use foam
extinguisher to deplete the air.
Extinguishing with water may cause a
further spread of fire.
4. Water the surrounding equipment to
prevent the spread of fire.
5. Wear fire protective suit and fight fire
from high points.
6. Keep out from incident area except
related personnel.
Extinguisher: Usage of mist type enhances, foam,
powder or gas extinguishers are effective.
No Water-based extinguisher should be
used.

2. Updated on 3
rd
May 2011
Steps to take in case of leakage Remove the source of fire around.
1. In a large scale: Keep out the leaking
area by rope. Water protective suit
while working.
Block the leaking liquid by soil to a
safety. Collect the remained liquid in
containers so as not to be effused to
the river or drainage.
2. In a small scale: Collect the liquid by
absorbing into soil. Wipe out the leaked
area completely.
3. In the sea: Employ the oil fence and
absorb by adhesive mattress. On
employing the chemical, any
technological regulation set by the
Ministry of Transport must be complied.
Handling and Storage Handling: 1. When treating more amount than
designated, production, storage and
handling sites must satisfy the low
standards.
2. Avoid contacts with open flame, fire or
heat. Also do not evaporate
unnecessary.
3. Keep in a room temperature. Keep out
of moisture and impurities.
4. Prevent from static. Working suit and
boots should also be conductive.
5. Ventilate often and be cautious of fire:
vapor generated from petroleum
products tend to stay undercurrent
because if its weight.
6. When repairing/processing the
equipment that still contain the danger,
remove it completely before working.
7. Wear protective whenever there is a
contact with skin and eye.
8. Use airtight containers.
9. Do not attempt to use siphon by mouth.
Storage: 1. Keep in a cool, enclosed area with
sufficient ventilation.
2. Indicate the dangerous article in
storage.
3. Avoid heat, spark, flame as well as static.
4. Electrical appliances in storage area
should be properly insulated.
5. Avoid con tacts and storage in the same
place with halogen, strong acid, alkali and
acidic substance.

3. Updated on 3
rd
May 2011
Exposure Manageable density: No provision.
prevention method
Allowable density: 3 mg/m (as mineral oil mist)
ACGIH (1993-94) TWA 5 mg/m (as
mineral oil mist)
Facility: In the presence of mist, isolate the origin
or ventilate. Require eye and body
washing facility near the work place.
Protective equipment: Air mask: Wear the mask as necessary.
Safety glass: Wear glass to prevent
contacts with eyes.
Protective gloves: Wear oil proof and long
sleeve suit in prolonged exposure and wet
condition.
Typical Physical/Chemical Appearance: Clear liquid
properties Odour:
Volatility: None
Density at 300
C, g/cm3 7.65
Viscosity @ 100
0
C, cst 106 – 119
@ 40
0
C, cst 766 – 831
Viscosity Index: 236 - 248
Pour Point,
0
C -45
0
C
TBN mgKOH/G 19.4 – 19.6
Composition / Information on Chemical Characterization Petroleum hydrocarbons (main
Ingredients component) and multipurpose additive
Package.
Dangerous components No
Danger Flash point 210
0
C (COC)
(Stability and response) Combustion point No data available.
Explosive limits Upper: 7% Lower: 1% (theoretical)
Flammability It is not classed as flammable.
Combustibility (spontaneous, water
reaction)
None
Oxidation None
Self reaction, explosion None
Stability Stable
Reaction Avoid Contact with strong acid.
Toxicity Skin Corrosively None
Irritation (Skin, eye) Prolonged or repeated exposure may
cause irritation
Sensitivity No data available
Acute toxicity Dosage rat LD 50:5g/g or more
(theoretical)
Blood poison No data available
Chronic toxicity Carcinogenic No data available
Mutagenicity (microorganism,
abnormal chromosome)
No data available

4. Updated on 3
rd
May 2011
Reproductive effect No data available
Deformity No data available
Information not availableOther (including the fume production
when reacted with water)
Environmental effect Dissolution Information not available
Accumulation Information not available
Aquatic Information not available
Other No data available
Disposal 1. Company should disposed industrial wastes by itself or consign the disposal
to an agent with governor's permit or local public bodies.
2. Abandonment is prohibited.
3. In case of land disposal, incinerator should be used beforehand. Substances
in cinders must comply with the regulations standards as follows: copper or
its compound, hexavalent chromium and its compound, organic phosphorus
compound, led or its compound, calcium or its compound, cyanide, PCB,
arsenic or its compound.
4. Combustion must be held in the safe place with safe method and also with a
supervisor.
Transportation 1. Inspect the possible leakage. Secure the transporting procedure to prevent
from accidental falling and damaging.
2. When transporting more amount than designated, the Ministry of Home
Affairs requires the vehicle to hoist the sign of danger. The vehicle also must
be furnished with fire extinguisher. The transportation vehicle must be below
3m in height.
3. Do not transport class I and VI explosives or high pressure gas together.
Other Information
Product Type / Uses Lubricating oil for diesel and gasoline engines or machineries.
Other Information This product may be a mixture formulated in part with components purchased
from other companies. Where propriety or trade secret materials are used,
TOHO relies on the hazard evaluation submitted by the other manufacturer.
Product safety data sheet is to be submitted to companies as a reference information in order to ensure the
safe handling of toxic chemical products. Those who may be concerned should understand that they are
responsible for their proper treatment to each incident and to refer to the instructions when necessary.
Therefore this data sheet itself is not a guarantee for safety.