This safety data sheet provides information on the hazards of a product called P 80 Kaltmetall neu. It contains styrene, which is harmful if inhaled, and solvent naphtha, which is harmful and irritating. The product is flammable and can irritate eyes and skin. When handling the product, protective equipment including gloves and eye protection should be worn.
This safety data sheet provides information on a product called P 85. It contains styrene, which is harmful if inhaled, and can irritate eyes and skin. The product is flammable and protective equipment like gloves and goggles should be worn when handling it. It requires proper ventilation and storage away from food.
This document provides safety information for the product P 90 Easy. It contains styrene, which is harmful if inhaled and irritating to eyes and skin. Appropriate personal protective equipment should be worn when handling this product. If exposed, fresh air should be supplied and medical advice sought. The product is flammable and appropriate precautions against fire and explosion should be taken during storage and use.
This safety data sheet provides information on the product P 70. P 70 is a mixture of substances including styrene (10-25%), aluminum powder (≤2.5%), and solvent naphtha (<1.0%) that is classified as harmful and irritating. The product requires proper ventilation and protective equipment during handling and storage due to its flammable nature and potential to form explosive vapors. Guidelines are provided on first aid measures and accidental release response in case of exposure.
This document provides safety information for P35 Elastic, a knife filler and surfacer produced by MIPA AG. It contains styrene, which is harmful if inhaled. Personal protective equipment like gloves, goggles and respiratory protection are required when handling this product. The product is flammable and precautions must be taken to avoid fire and explosion, such as keeping ignition sources away. If exposed, the product can irritate eyes and skin and cause symptoms even after several hours, so medical observation may be required. Spills should be absorbed with materials like sand and not flushed with water. Proper storage in a tightly sealed container away from food is necessary.
This safety data sheet summarizes information on the product P 99 Multi Star. It contains styrene, which is harmful if inhaled, and irritates eyes and skin. The product is also flammable. Proper protective equipment should be worn when handling to avoid inhalation, eye and skin contact. The product contains hazardous ingredients and proper disposal is required in accordance with regulations.
This safety data sheet provides information on the product P 911. It identifies the product, supplier, hazards, composition, and safety precautions. The product contains styrene which is harmful if inhaled, irritating to eyes and skin, and flammable. The sheet provides guidance on handling, storage, exposure controls, firefighting measures, accidental release measures, transport, and disposal.
This document provides a safety data sheet for product A 40, describing:
1) The product and company details
2) Hazards associated with the product including flammability and potential to cause skin/eye irritation or drowsiness
3) The main ingredients in the product and their hazards
4) First aid measures, firefighting measures, and accidental release measures
1. The document is a safety data sheet for a natural hemp fiber product called "Hanffaser" used as a sealant.
2. The product is not considered hazardous according to current EC guidelines and classifications. It does not require labeling.
3. The product is a natural hemp fiber and is not considered dangerous or hazardous when used and handled properly.
This safety data sheet provides information on a product called P 85. It contains styrene, which is harmful if inhaled, and can irritate eyes and skin. The product is flammable and protective equipment like gloves and goggles should be worn when handling it. It requires proper ventilation and storage away from food.
This document provides safety information for the product P 90 Easy. It contains styrene, which is harmful if inhaled and irritating to eyes and skin. Appropriate personal protective equipment should be worn when handling this product. If exposed, fresh air should be supplied and medical advice sought. The product is flammable and appropriate precautions against fire and explosion should be taken during storage and use.
This safety data sheet provides information on the product P 70. P 70 is a mixture of substances including styrene (10-25%), aluminum powder (≤2.5%), and solvent naphtha (<1.0%) that is classified as harmful and irritating. The product requires proper ventilation and protective equipment during handling and storage due to its flammable nature and potential to form explosive vapors. Guidelines are provided on first aid measures and accidental release response in case of exposure.
This document provides safety information for P35 Elastic, a knife filler and surfacer produced by MIPA AG. It contains styrene, which is harmful if inhaled. Personal protective equipment like gloves, goggles and respiratory protection are required when handling this product. The product is flammable and precautions must be taken to avoid fire and explosion, such as keeping ignition sources away. If exposed, the product can irritate eyes and skin and cause symptoms even after several hours, so medical observation may be required. Spills should be absorbed with materials like sand and not flushed with water. Proper storage in a tightly sealed container away from food is necessary.
This safety data sheet summarizes information on the product P 99 Multi Star. It contains styrene, which is harmful if inhaled, and irritates eyes and skin. The product is also flammable. Proper protective equipment should be worn when handling to avoid inhalation, eye and skin contact. The product contains hazardous ingredients and proper disposal is required in accordance with regulations.
This safety data sheet provides information on the product P 911. It identifies the product, supplier, hazards, composition, and safety precautions. The product contains styrene which is harmful if inhaled, irritating to eyes and skin, and flammable. The sheet provides guidance on handling, storage, exposure controls, firefighting measures, accidental release measures, transport, and disposal.
This document provides a safety data sheet for product A 40, describing:
1) The product and company details
2) Hazards associated with the product including flammability and potential to cause skin/eye irritation or drowsiness
3) The main ingredients in the product and their hazards
4) First aid measures, firefighting measures, and accidental release measures
1. The document is a safety data sheet for a natural hemp fiber product called "Hanffaser" used as a sealant.
2. The product is not considered hazardous according to current EC guidelines and classifications. It does not require labeling.
3. The product is a natural hemp fiber and is not considered dangerous or hazardous when used and handled properly.
This safety data sheet provides information on a product called 925 WR-P. It contains no hazardous ingredients according to regulation (EC) 1272/2008. The product is a mixture used for stencil production in screen and textile printing. It contains a polymer and citrate that can cause eye irritation. Precautions are outlined for safe handling, storage, disposal, firefighting and accidental release. Toxicity data on the product is not available but no acute hazards are expected based on component information.
Diethylenetriaminepenta(methylene-phosphonic acid) (cas 15827-60-8) is an irritant that causes skin, eye and respiratory irritation. It is sold as a solution and should be handled with gloves and eye protection. The document provides identification information, hazards, composition, first aid measures, handling and storage guidance.
This document provides a material safety data sheet for 4-Bromopyridine hydrochloride (CAS 19524-06-2). It lists the product's identification, hazards, composition, first aid measures, firefighting measures, accidental release measures, handling and storage, exposure controls and personal protection, physical and chemical properties, stability and reactivity, toxicological information, ecological information, disposal considerations, transport information, and regulatory information. The product is harmful if swallowed, a skin and eye irritant, and may cause respiratory irritation.
This document provides information on the chemical 1-Bromo-2-methylpropane (CAS 78-77-3). It lists the product identifiers and relevant uses. It also describes the hazards, including being highly flammable and irritating to eyes, skin, and respiratory system. The document provides details on the composition, first aid measures, firefighting measures, accidental release measures, handling and storage, exposure controls and personal protection, physical and chemical properties, stability and reactivity, toxicological information, ecological information, and regulatory information.
1. This document provides information on the chemical 5-Bromo-2-chloropyrimidine (CAS 32779-36-5), including its hazards, safe handling and storage, first aid measures, and regulatory information.
2. 5-Bromo-2-chloropyrimidine is an irritant and may cause skin, eye and respiratory irritation upon contact. It has a melting point between 73-79°C and molecular weight of 193.43 g/mol.
3. Proper protective equipment should be worn when handling this chemical. If contact occurs, rinse thoroughly with water and seek medical advice. Store in a cool, dry and
Mipa Vorreiniger "Mat & Clean" is a professional sanding paste that cleans surfaces of wax, grease, and silicone, leaving a matted finish in a single step. It can be applied by hand using a wet sanding fleece or sponge with circular motions, or by machine using a fine sanding sponge at low speed. The product contains no hazardous materials according to regulations and has a VOC content below the EC limiting value.
This document provides a material safety data sheet for dipyridamole (CAS 58-32-2). It lists dipyridamole's hazards, including skin and eye irritation, and recommends protective equipment when handling. The document describes dipyridamole's physical properties, toxicity, and disposal considerations. It contains safety information for transportation and regulatory compliance.
This document provides safety information for a fertilizer product called Rooter. It contains the following key details:
- Rooter is an EC fertilizer solution containing phosphoric acid as the main hazardous component.
- It can cause severe skin and eye damage upon contact. Proper protective equipment should be worn when handling.
- In the event of accidental skin or eye exposure, immediate first aid measures such as rinsing with water are recommended.
- The product should be stored in its original labeled container away from food and animal feed at temperatures above -10°C.
This document provides a material safety data sheet for 2-Cyanoacetamide (CAS 107-91-5). It identifies the product and company details, lists the product's hazards and contains information on its safe handling, storage, exposure controls, accidental release measures, toxicological information and regulatory details. The key hazards are that it is harmful if swallowed, causes skin and eye irritation, and may cause respiratory irritation.
Valeo Braking Systems Brake Fluid DOT 5.1 material safety data sheet 402407 4...Hugo Vallet
Valeo Braking Systems Brake Fluid DOT 5.1 material safety data sheet 402407 402408 402409
SAFETY DATA SHEET in accordance with Regulation (EC) No 1907/2006 and Regulation (CE) N. 453/2010.
- trade name: BRAKE FLUID DOT 5.1
- use of the substance/preparation: Functional fluids (brake fluid) for automobile industry.
- identification of the company: Valeo Service UK LTD
Heming Road - Washford - Redditch – Worcs B98 ODZ - England
- Website: www.valeoservice.co.uk
- Emergency telephone number: 844 892 0111 (24 hrs)
Learn more about Valeo Multi-Specialist DNA on www.valeoservice.co.uk
Valeo, automotive technology, naturally
This document provides information on chloromethyl pivalate (CAS 18997-19-8), including suppliers, hazards, safe handling and storage, exposure controls, physical and chemical properties, toxicological information, and regulatory information. Chloromethyl pivalate is flammable and harmful if inhaled, swallowed, or absorbed through skin. It causes skin and eye irritation. Proper precautions such as gloves, eye protection and adequate ventilation should be used when handling.
This safety data sheet provides information on KC-Trockenperlen WS 2050. It is an absorbent solid used for drying liquids and gases. The document identifies the product, manufacturer contact information, composition, hazards, first aid measures, handling and storage guidelines, exposure controls, physical and chemical properties, stability, disposal considerations and regulatory information.
As said earlier, Gypsum occurs along with other minerals such as halite and anhydrite. These all are the evaporite minerals, and hence the gypsum. It means that Gypsum is the sedimentary deposit, that is to say, it is deposited by the action or the work of wind or the water, usually in the bottom of the water body. In particular, Sulfate is deposited from the natural brine that occurs in the ocean, which is then followed by anhydrite and halite
This document provides information on the chemical 1-methylimidazole (CAS 616-47-7), including its identification, hazards, composition, first aid measures, firefighting measures, accidental release measures, handling and storage, exposure controls and personal protection. 1-Methylimidazole is harmful if swallowed or in contact with skin, and causes severe skin burns and eye damage. Personal protective equipment including gloves, goggles and protective clothing should be worn when handling this product.
The document provides safety information about a product called Pt-01. It contains several hazardous chemicals including strong caustics that are toxic if swallowed or inhaled and corrosive to skin. The product should only be used with protective equipment and in well ventilated areas. It can cause burns if not treated promptly upon contact with skin or eyes.
This document provides safety information about Brodifacoum Technical Material. It lists Brodifacoum as the active ingredient and classifies it as highly toxic if swallowed or absorbed through skin contact. The document outlines handling, storage, exposure and first aid procedures to mitigate health and environmental risks. It also provides physical and chemical properties, toxicological data, and disposal guidance in compliance with relevant regulations.
This document provides safety information for a product called TGK. It contains a mixture of hydrocarbons and 2-butoxyethanol. The product is classified as hazardous and can cause skin and eye irritation. It may be fatal if swallowed and enters airways. Exposure controls are outlined, including the use of protective gloves, clothing, goggles and respiratory protection. Information on toxicological effects and environmental hazards are also included.
This document provides a material safety data sheet for 5-Cyanoindole (CAS 15861-24-2). It identifies the product and company details, lists hazards such as skin and eye irritation, and recommends protective equipment. It also provides physical and chemical property data, toxicology information, and handling and storage instructions. The product is a crystalline beige solid with no odor reported.
This safety data sheet provides information on the product TALISMA UL. It contains a mixture of cypermethrin and piperonyl butoxide. The document lists hazards such as being very toxic to aquatic life with long lasting effects. It provides handling, storage, exposure and personal protective equipment recommendations. The product has a density of 0.8933 g/ml and a flash point above 79°C. It is not readily biodegradable and components may bioaccumulate in fish and other organisms.
This document provides suppliers and safety information for diethylamine (cas 109-89-7), including its identification, hazards, composition, first aid measures, firefighting measures, accidental release measures, handling and storage, exposure controls and personal protection, physical and chemical properties, stability and reactivity, and toxicological information. It identifies diethylamine as a flammable liquid and vapor that is harmful if inhaled, swallowed, or absorbed through the skin, and causes severe skin burns and eye damage.
Salt lake-window-tinting-window-film-dry wired-liquid-nanotint-sdsSaltLakeWindowTinting
This file is from Salt Lake City, Utah. It contains information about window tinting. All information and rights to the material are copyrighted by the company to whom it belongs to. Thank you for viewing. Salt Lake Window Tinting hopes you enjoy.
This safety data sheet provides information on a product called 925 WR-P. It contains no hazardous ingredients according to regulation (EC) 1272/2008. The product is a mixture used for stencil production in screen and textile printing. It contains a polymer and citrate that can cause eye irritation. Precautions are outlined for safe handling, storage, disposal, firefighting and accidental release. Toxicity data on the product is not available but no acute hazards are expected based on component information.
Diethylenetriaminepenta(methylene-phosphonic acid) (cas 15827-60-8) is an irritant that causes skin, eye and respiratory irritation. It is sold as a solution and should be handled with gloves and eye protection. The document provides identification information, hazards, composition, first aid measures, handling and storage guidance.
This document provides a material safety data sheet for 4-Bromopyridine hydrochloride (CAS 19524-06-2). It lists the product's identification, hazards, composition, first aid measures, firefighting measures, accidental release measures, handling and storage, exposure controls and personal protection, physical and chemical properties, stability and reactivity, toxicological information, ecological information, disposal considerations, transport information, and regulatory information. The product is harmful if swallowed, a skin and eye irritant, and may cause respiratory irritation.
This document provides information on the chemical 1-Bromo-2-methylpropane (CAS 78-77-3). It lists the product identifiers and relevant uses. It also describes the hazards, including being highly flammable and irritating to eyes, skin, and respiratory system. The document provides details on the composition, first aid measures, firefighting measures, accidental release measures, handling and storage, exposure controls and personal protection, physical and chemical properties, stability and reactivity, toxicological information, ecological information, and regulatory information.
1. This document provides information on the chemical 5-Bromo-2-chloropyrimidine (CAS 32779-36-5), including its hazards, safe handling and storage, first aid measures, and regulatory information.
2. 5-Bromo-2-chloropyrimidine is an irritant and may cause skin, eye and respiratory irritation upon contact. It has a melting point between 73-79°C and molecular weight of 193.43 g/mol.
3. Proper protective equipment should be worn when handling this chemical. If contact occurs, rinse thoroughly with water and seek medical advice. Store in a cool, dry and
Mipa Vorreiniger "Mat & Clean" is a professional sanding paste that cleans surfaces of wax, grease, and silicone, leaving a matted finish in a single step. It can be applied by hand using a wet sanding fleece or sponge with circular motions, or by machine using a fine sanding sponge at low speed. The product contains no hazardous materials according to regulations and has a VOC content below the EC limiting value.
This document provides a material safety data sheet for dipyridamole (CAS 58-32-2). It lists dipyridamole's hazards, including skin and eye irritation, and recommends protective equipment when handling. The document describes dipyridamole's physical properties, toxicity, and disposal considerations. It contains safety information for transportation and regulatory compliance.
This document provides safety information for a fertilizer product called Rooter. It contains the following key details:
- Rooter is an EC fertilizer solution containing phosphoric acid as the main hazardous component.
- It can cause severe skin and eye damage upon contact. Proper protective equipment should be worn when handling.
- In the event of accidental skin or eye exposure, immediate first aid measures such as rinsing with water are recommended.
- The product should be stored in its original labeled container away from food and animal feed at temperatures above -10°C.
This document provides a material safety data sheet for 2-Cyanoacetamide (CAS 107-91-5). It identifies the product and company details, lists the product's hazards and contains information on its safe handling, storage, exposure controls, accidental release measures, toxicological information and regulatory details. The key hazards are that it is harmful if swallowed, causes skin and eye irritation, and may cause respiratory irritation.
Valeo Braking Systems Brake Fluid DOT 5.1 material safety data sheet 402407 4...Hugo Vallet
Valeo Braking Systems Brake Fluid DOT 5.1 material safety data sheet 402407 402408 402409
SAFETY DATA SHEET in accordance with Regulation (EC) No 1907/2006 and Regulation (CE) N. 453/2010.
- trade name: BRAKE FLUID DOT 5.1
- use of the substance/preparation: Functional fluids (brake fluid) for automobile industry.
- identification of the company: Valeo Service UK LTD
Heming Road - Washford - Redditch – Worcs B98 ODZ - England
- Website: www.valeoservice.co.uk
- Emergency telephone number: 844 892 0111 (24 hrs)
Learn more about Valeo Multi-Specialist DNA on www.valeoservice.co.uk
Valeo, automotive technology, naturally
This document provides information on chloromethyl pivalate (CAS 18997-19-8), including suppliers, hazards, safe handling and storage, exposure controls, physical and chemical properties, toxicological information, and regulatory information. Chloromethyl pivalate is flammable and harmful if inhaled, swallowed, or absorbed through skin. It causes skin and eye irritation. Proper precautions such as gloves, eye protection and adequate ventilation should be used when handling.
This safety data sheet provides information on KC-Trockenperlen WS 2050. It is an absorbent solid used for drying liquids and gases. The document identifies the product, manufacturer contact information, composition, hazards, first aid measures, handling and storage guidelines, exposure controls, physical and chemical properties, stability, disposal considerations and regulatory information.
As said earlier, Gypsum occurs along with other minerals such as halite and anhydrite. These all are the evaporite minerals, and hence the gypsum. It means that Gypsum is the sedimentary deposit, that is to say, it is deposited by the action or the work of wind or the water, usually in the bottom of the water body. In particular, Sulfate is deposited from the natural brine that occurs in the ocean, which is then followed by anhydrite and halite
This document provides information on the chemical 1-methylimidazole (CAS 616-47-7), including its identification, hazards, composition, first aid measures, firefighting measures, accidental release measures, handling and storage, exposure controls and personal protection. 1-Methylimidazole is harmful if swallowed or in contact with skin, and causes severe skin burns and eye damage. Personal protective equipment including gloves, goggles and protective clothing should be worn when handling this product.
The document provides safety information about a product called Pt-01. It contains several hazardous chemicals including strong caustics that are toxic if swallowed or inhaled and corrosive to skin. The product should only be used with protective equipment and in well ventilated areas. It can cause burns if not treated promptly upon contact with skin or eyes.
This document provides safety information about Brodifacoum Technical Material. It lists Brodifacoum as the active ingredient and classifies it as highly toxic if swallowed or absorbed through skin contact. The document outlines handling, storage, exposure and first aid procedures to mitigate health and environmental risks. It also provides physical and chemical properties, toxicological data, and disposal guidance in compliance with relevant regulations.
This document provides safety information for a product called TGK. It contains a mixture of hydrocarbons and 2-butoxyethanol. The product is classified as hazardous and can cause skin and eye irritation. It may be fatal if swallowed and enters airways. Exposure controls are outlined, including the use of protective gloves, clothing, goggles and respiratory protection. Information on toxicological effects and environmental hazards are also included.
This document provides a material safety data sheet for 5-Cyanoindole (CAS 15861-24-2). It identifies the product and company details, lists hazards such as skin and eye irritation, and recommends protective equipment. It also provides physical and chemical property data, toxicology information, and handling and storage instructions. The product is a crystalline beige solid with no odor reported.
This safety data sheet provides information on the product TALISMA UL. It contains a mixture of cypermethrin and piperonyl butoxide. The document lists hazards such as being very toxic to aquatic life with long lasting effects. It provides handling, storage, exposure and personal protective equipment recommendations. The product has a density of 0.8933 g/ml and a flash point above 79°C. It is not readily biodegradable and components may bioaccumulate in fish and other organisms.
This document provides suppliers and safety information for diethylamine (cas 109-89-7), including its identification, hazards, composition, first aid measures, firefighting measures, accidental release measures, handling and storage, exposure controls and personal protection, physical and chemical properties, stability and reactivity, and toxicological information. It identifies diethylamine as a flammable liquid and vapor that is harmful if inhaled, swallowed, or absorbed through the skin, and causes severe skin burns and eye damage.
Salt lake-window-tinting-window-film-dry wired-liquid-nanotint-sdsSaltLakeWindowTinting
This file is from Salt Lake City, Utah. It contains information about window tinting. All information and rights to the material are copyrighted by the company to whom it belongs to. Thank you for viewing. Salt Lake Window Tinting hopes you enjoy.
The document is a safety data sheet for DryWired Liquid NanoTint. It provides information on product identification, hazards, composition, safe handling and storage, exposure controls, physical and chemical properties, stability, toxicological information and more. The product contains flammable liquids and exposure may cause drowsiness or skin/eye irritation. Proper precautions like gloves, ventilation and avoiding ignition sources are recommended when handling.
The document is a safety data sheet for DryWired Liquid NanoTint. It provides information on product identification, hazards, composition, safe handling and storage, exposure controls, physical and chemical properties, stability, toxicological information and more. The product contains flammable liquids and exposure may cause drowsiness or skin/eye irritation. Proper precautions like gloves, ventilation and avoiding ignition sources are recommended when handling.
This document provides a safety data sheet for DL-Carnitine hydrochloride. It lists the product identifiers and supplier contact information. The substance is classified as causing skin irritation, eye irritation, and may cause respiratory irritation. Personal protective equipment is recommended when handling the substance, including gloves, eye protection and respiratory protection. The substance should be stored in a dry, cool area and handled according to good industrial hygiene practices.
Energol ic-hfx-404-9389 Liên hệ: Mr Tùng 0987 988 407 website: www.khodaumo.comĐỗ Bá Tùng
This safety data sheet provides information on Energol IC-HF X 404 engine oil. It contains no hazardous ingredients above regulated thresholds. Prolonged skin contact may cause irritation. Used engine oil may contain carcinogens. If contact occurs, wash skin and eyes thoroughly. Store in a dry, well-ventilated area away from heat and sunlight. In a fire, this product may decompose and produce carbon oxides, sulfur oxides and metal oxides. Dispose of waste via licensed contractor and in accordance with local regulations to prevent environmental contamination.
- Nitrous oxide is a liquefied gas that is classified as an oxidizing gas and gas under pressure.
- It requires proper storage and handling to prevent contact with combustible or reducing materials.
- Adverse health effects include central nervous system impairment and hematologic effects with overexposure.
Sds resist 86 av - comp. b - marine protective - english (us) - united states택진 김
This document provides a material safety data sheet for Resist 86 AV - Comp. B, which contains zinc powder and zinc oxide. It is considered hazardous and may cause target organ damage based on animal data. Exposure can cause eye, skin, or respiratory irritation. Inhalation of dusts or fumes can potentially damage lungs or the upper respiratory tract. The product is a solid powder that is not flammable but can decompose when burned, producing metal oxide fumes. Proper personal protective equipment should be worn when handling. Spills should be cleaned up promptly and the product is toxic to aquatic life so must be handled carefully to prevent environmental contamination.
Sds resist 86 av - comp. b - marine protective - english (us) - united states택진 김
This document provides a material safety data sheet for Resist 86 AV - Comp. B, which contains zinc powder and zinc oxide. It is considered hazardous and may cause target organ damage based on animal data. Exposure can cause eye, skin, or respiratory irritation. Inhalation of dusts or fumes can potentially damage lungs or the upper respiratory tract over time. The product contains 50-100% zinc and 2.5-10% zinc oxide and is very toxic to aquatic life with potential long term effects in aquatic environments. Proper personal protective equipment should be used when handling.
Website: https://www.customtintsolutions.com/cities/austin/
Custom Tint Solutions Window Film Austin.
This file is from Austin, Texas. It contains information about window tinting. All information and rights to the material are copyrighted by the company to whom it belongs to. Thank you for viewing. Custom Tint Solutions hopes you enjoy.
Mipa Vicrom is a basecoat that creates a chrome-like mirror effect surface. It is intended to coat rims, trim, and other parts. To protect against weathering and mechanical stress, the surface should be recoated with Mipa 2K clearcoats. Mipa Vicrom has a mixing ratio for ready to spray use and can be thinned if needed. It is applied in thin, uniform layers with a spray gun at low pressure to achieve the best mirror effect.
MP ProtectiveHalfMask-Box Reusable is a reusable half mask for use in paint shops. It is made of a flexible, lightweight plastic that provides maximum comfort while complying with European and US safety standards. The mask comes with two each of filters for organic gases/vapors and particles, as well as mounts for adding extra filters. Replacement filters can also be purchased.
This document provides product information for Mipa Ziehspachtel PL10, a two-component long-term paste filler based on unsaturated polyester resins. It is suitable for repairing larger body areas on vehicles and machinery. The putty has a fine grain and can be applied in thin layers. It has a long pot life and is heat resistant up to 180°C. The document describes the product's applications, mixing instructions, drying times, and safety precautions.
MP FineLineTape is a masking tape suitable for multi-color and design painting. It produces almost no edges during painting due to its extremely thin material of 0.12mm. It adheres well to different substrates and can be used for several successive drying processes up to 120°C without needing to remask. The special carrier material ensures perfect results when properly used, including for water-based paints. It is available in 55m rolls in widths of 3mm, 6mm, 9mm and 12mm.
MP Polierteller offers backing pads in various sizes that work with MP polishing foams and pads to achieve a perfect surface finish on vehicles. The backing pads and unique MP ONE-STEP Super-Polish agent allow users to polish out trapped dust and remove scratches in a single process when used together. The document provides technical details and item numbers for three backing pad sizes available for purchase.
MP ONE-STEP Super-Polish is a one-step polish that can remove traces of spray dust, spraying transitions, and sanding traces in one operation. It allows polishing after fine sanding with P1500-P2000 paper without leaving holograms. Paint defects can be removed and the product easily wipes away without residue, providing a perfect finish for paint surfaces. The polish is silicone-free with aluminum oxide and suitable for scratch-resistant nano coatings.
The MP Polierer Electronic is a compact, ergonomic electric polishing machine. It features a rotary speed selector and high torque motor for perfect work without fatigue. A 6x microprocessor electronic ensures constant power transfer without loss of performance or risk of burning. It is optimized for use with MP polishing pads and the MP ONE-STEP Super-Polish compound to achieve high quality surface finishes.
This document discusses coatings and surface treatments from Mipa. It notes that surface quality makes an important first impression, and that customers expect damage-free surfaces. It then summarizes Mipa's products for spot repair and coatings, including their aerosol and mixing systems that can produce thousands of color shades. The document highlights Mipa's coatings for sports equipment and aircraft to protect against weathering while allowing flexibility or conductivity as needed.
This document provides safety information for a 2K-Plastic-Grundierfiller product. It contains hazardous chemicals including xylene, ethyl acetate, and solvent naphtha. The product is highly flammable and harmful if inhaled, in contact with skin, or if swallowed. It can cause irritation to eyes, skin, and respiratory tract. In the event of contact, remove contaminated clothing and rinse area with water. Seek medical help if symptoms persist. The product requires proper storage and handling to prevent fire or exposure.
1) The document provides product information for Mipa 2K-Plastic-Grundierfiller, a fast drying primer-surfacer that adheres directly to various plastic materials used in automotive applications.
2) It can be used as both an adhesion promoter and filler in a single application and allows wet-on-wet application with all 1K and 2K paints.
3) The primer has a pot life of 4-5 hours, dries to dust in 25-30 minutes at 20°C object temperature, and achieves full hardness within 60-70 minutes at 20°C or 20-30 minutes at 60°C object temperature.
This document provides a safety data sheet for Mipa 1K-Fastfiller grau, a knife filler and surfacer. It lists the product ingredients and identifies those that are hazardous, including xylene, butan-1-ol, ethanol, n-butyl acetate, ethyl acetate, bisphenol, phosphoric acid, and solvent naphtha. It also provides handling guidelines, protective equipment recommendations, and emergency procedures for accidental release. The product contains flammable and hazardous materials and proper precautions should be taken when using it.
Mipa 1K-Fast-Filler is a 1K repair filler for automotive use that has excellent filling power. It can be applied to sanded old paint layers, shop primers, and directly to steel. It sands and dries quickly, saving time. It is chromate and lead free. It sprays easily at a viscosity of 18-22 seconds and dries fully hard in under an hour when applied at a thickness of 40-50 microns. Proper thinning and application conditions ensure best performance.
1. Page 1/6
Safety Data Sheet
according to 1907/2006/EC, Article 31
Printing date 15.03.2010 Revision: 12.03.2010
* 1 Identification of the substance/preparation and of the company/undertaking
· Product details
· Trade name: P 80 Kaltmetall neu
· Application of the substance / the preparation Knife filler/ Surfacer
· Manufacturer/Supplier:
MIPA AG
Am Oberen Moos 1
D-84051 Essenbach
Tel.: +49(0)8703-922-0
Fax.: +49(0)8703-922-100
e-mail: sdb-registratur@mipa-paints.com
www.mipa-paints.com
· Further information obtainable from: Laboratory
· Information in case of emergency: +49(0)700 24112112 (MIP)
* 2 Hazards identification
· Hazard description:
Xn Harmful
· Information concerning particular hazards for human and environment:
The product has to be labelled due to the calculation procedure of the "General Classification guideline for
preparations of the EU" in the latest valid version.
R 10 Flammable.
R 20 Harmful by inhalation.
R 36/38 Irritating to eyes and skin.
· Classification system:
The classification is according to the latest editions of the EU-lists, and extended by company and literature
data.
3 Composition/information on ingredients
· Chemical characterization
· Description: Mixture of substances listed below with nonhazardous additions.
· Dangerous components:
CAS: 100-42-5 styrene 10-25%
EINECS: 202-851-5 Xn, Xi; R 10-20-36/38
CAS: 64742-95-6 Solvent naphtha (petroleum), light arom. <1.0%
EINECS: 265-199-0 Xn, Xi, N; R 10-37-51/53-65-66-67
· Additional information: For the wording of the listed risk phrases refer to section 16.
4 First aid measures
· General information:
Symptoms of poisoning may even occur after several hours; therefore medical observation for at least 48
hours after the accident.
· After inhalation:
Supply fresh air. If required, provide artificial respiration. Keep patient warm. Consult doctor if symptoms
persist.
In case of unconsciousness place patient stably in side position for transportation.
· After skin contact: Immediately wash with water and soap and rinse thoroughly.
(Contd. on page 2)
GB
DR
2. Page 2/6
Safety Data Sheet
according to 1907/2006/EC, Article 31
Printing date 15.03.2010 Revision: 12.03.2010
Trade name: P 80 Kaltmetall neu
(Contd. of page 1)
· After eye contact:
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
· After swallowing: If symptoms persist consult doctor.
5 Fire-fighting measures
· Suitable extinguishing agents: CO2, sand, extinguishing powder. Do not use water.
· For safety reasons unsuitable extinguishing agents: Water with full jet
· Protective equipment: Mouth respiratory protective device.
6 Accidental release measures
· Person-related safety precautions: Wear protective equipment. Keep unprotected persons away.
· Measures for environmental protection: Do not allow to enter sewers/ surface or ground water.
· Measures for cleaning/collecting:
Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).
Dispose contaminated material as waste according to item 13.
Ensure adequate ventilation.
Do not flush with water or aqueous cleansing agents
* 7 Handling and storage
· Handling:
· Information for safe handling:
Ensure good ventilation/exhaustion at the workplace.
Prevent formation of aerosols.
· Information about fire - and explosion protection:
Keep ignition sources away - Do not smoke.
Protect against electrostatic charges.
· Storage:
· Requirements to be met by storerooms and receptacles: No special requirements.
· Information about storage in one common storage facility: Store away from foodstuffs.
· Further information about storage conditions: Keep container tightly sealed.
· Storage class: 3
* 8 Exposure controls/personal protection
· Additional information about design of technical facilities: No further data; see item 7.
· Ingredients with limit values that require monitoring at the workplace:
100-42-5 styrene
WEL () Short-term value: 1080 mg/m³, 250 ppm
Long-term value: 430 mg/m³, 100 ppm
· Additional information: The lists valid during the making were used as basis.
· Personal protective equipment:
· General protective and hygienic measures:
Keep away from foodstuffs, beverages and feed.
Immediately remove all soiled and contaminated clothing
Wash hands before breaks and at the end of work.
Avoid contact with the eyes and skin.
(Contd. on page 3)
GB
DR
3. Page 3/6
Safety Data Sheet
according to 1907/2006/EC, Article 31
Printing date 15.03.2010 Revision: 12.03.2010
Trade name: P 80 Kaltmetall neu
(Contd. of page 2)
· Respiratory protection:
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure
use self-contained respiratory protective device.
· Protection of hands:
Protective gloves
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/
the chemical mixture.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the
degradation
· Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality
and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the
resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the
application.
· Penetration time of glove material
The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be
observed.
· Eye protection:
Tightly sealed goggles
* 9 Physical and chemical properties
· General Information
Form: Fluid
Colour: According to product specification
Odour: Characteristic
· Change in condition
Melting point/Melting range: Undetermined.
Boiling point/Boiling range: 145°C
· Flash point: 34°C (DIN 53213)
· Ignition temperature: 480°C (DIN 51794)
· Self-igniting: Product is not selfigniting.
· Danger of explosion: Product is not explosive. However, formation of explosive air/vapour
mixtures are possible.
· Explosion limits:
Lower: 1.2 Vol %
Upper: 8.9 Vol %
· Vapour pressure at 20°C: 6 hPa
· Density at 20°C: 1.765 g/cm³ (DIN 53217)
· Solubility in / Miscibility with
water: Not miscible or difficult to mix.
(Contd. on page 4)
GB
DR
4. Page 4/6
Safety Data Sheet
according to 1907/2006/EC, Article 31
Printing date 15.03.2010 Revision: 12.03.2010
Trade name: P 80 Kaltmetall neu
(Contd. of page 3)
· Viscosity:
Dynamic at 20°C: 80000 mPas
· Solvent content:
Organic solvents: 0.2 %
VOC (EC) 4.2 g/l
· Solids content (weight-%): 85.1 %
* 10 Stability and reactivity
· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.
· Dangerous reactions No dangerous reactions known.
· Dangerous decomposition products: Carbon monoxide
* 11 Toxicological information
· Acute toxicity:
· LD/LC50 values relevant for classification:
100-42-5 styrene
Oral LD50 5000 mg/kg (rat)
Inhalative LC50/4 h 24 mg/l (rat)
· Primary irritant effect:
· on the skin: Irritant to skin and mucous membranes.
· on the eye: Irritating effect.
· Sensitization: No sensitizing effects known.
· Additional toxicological information:
The product shows the following dangers according to the calculation method of the General EU
Classification Guidelines for Preparations as issued in the latest version:
Harmful
Irritant
12 Ecological information
· General notes:
Water hazard class 2 (German Regulation) (Self-assessment): hazardous for water
Do not allow product to reach ground water, water course or sewage system.
Danger to drinking water if even small quantities leak into the ground.
* 13 Disposal considerations
· Product:
· Recommendation
Must not be disposed together with household garbage. Do not allow product to reach sewage system.
· European waste catalogue
08 01 11 waste paint and varnish containing organic solvents or other dangerous substances
(Contd. on page 5)
GB
DR
5. Page 5/6
Safety Data Sheet
according to 1907/2006/EC, Article 31
Printing date 15.03.2010 Revision: 12.03.2010
Trade name: P 80 Kaltmetall neu
(Contd. of page 4)
· Uncleaned packaging:
· Recommendation: Disposal must be made according to official regulations.
* 14 Transport information
· Land transport ADR/RID (cross-border)
· ADR/RID class: 3 (F1) Flammable liquids.
· Danger code (Kemler): -
· UN-Number: 3269
· Packaging group: III
· Hazard label: 3
· Description of goods: 3269 POLYESTER RESIN KIT
· Maritime transport IMDG:
· IMDG Class: 3
· UN Number: 3269
· Label 3
· Packaging group: III
· EMS Number: F-E,S-D
· Marine pollutant: No
· Proper shipping name: POLYESTER RESIN KIT
· Air transport ICAO-TI and IATA-DGR:
· ICAO/IATA Class: 3
· UN/ID Number: 3269
· Label 3
· Packaging group: III
· Proper shipping name: POLYESTER RESIN KIT
* 15 Regulatory information
· Labelling according to EU guidelines:
The product has been classified and marked in accordance with EU Directives / Ordinance on Hazardous
Materials.
· Code letter and hazard designation of product:
Xn Harmful
· Hazard-determining components of labelling:
styrene
(Contd. on page 6)
GB
DR
6. Page 6/6
Safety Data Sheet
according to 1907/2006/EC, Article 31
Printing date 15.03.2010 Revision: 12.03.2010
Trade name: P 80 Kaltmetall neu
(Contd. of page 5)
· Risk phrases:
10 Flammable.
20 Harmful by inhalation.
36/38 Irritating to eyes and skin.
· Safety phrases:
2 Keep out of the reach of children.
9 Keep container in a well-ventilated place.
13 Keep away from food, drink and animal feedingstuffs.
23 Do not breathe gas/fumes/vapour/spray (appropriate wording to be specified by the manufacturer).
25 Avoid contact with eyes.
46 If swallowed, seek medical advice immediately and show this container or label.
· National regulations:
· Information about limitation of use:
14807-96-6 Talk 3B
100-42-5 styrene 5
Class Share in %
NK 10-25
* 16 Other information
This information is based on our present knowledge. However, this shall not constitute a guarantee for any
specific product features and shall not establish a legally valid contractual relationship.
· Relevant R-phrases
10 Flammable.
20 Harmful by inhalation.
36/38 Irritating to eyes and skin.
37 Irritating to respiratory system.
51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
65 Harmful: may cause lung damage if swallowed.
66 Repeated exposure may cause skin dryness or cracking.
67 Vapours may cause drowsiness and dizziness.
· Department issuing MSDS: MIPA AG, Abteilung Umweltschutz
· Contact: Michaela Knall
· * Data compared to the previous version altered.
GB
DR