htdu

1. Master Scene Script
Master Scene Script is the standard and accepted format used for film production. The format
of it allows each scene to be understood and broken down properly. For example, in the
following script written in Master Scene Script you can see how the writer includes the time
and location at the top of the scene as well as actions being written in caps making them stand
out. The dialogue and description are mixed in the script allowing the reader to easily follow
the story.
The scene heading (slugline) shows the location, time of day and whether it is interior or
exterior. For example, in the example above it says "INT. STARBUCKS - DAY" which means it's
set at day time and is inside Starbucks.
Narritive description is the telling of the story as it unfolds on screen. It begins directly below
the scene heading. The writing should focus on action and should be concise to move the story
forward. In this example, the first line of the script shows narritive description by stating that
the bland music plays on the sound system while people chat and fingers clatter on keyboards,
going into a lot of detail but also keep the reader engaged.
Everything in a screenplay must be recorded in terms of picture and sound therefore meaning
narrative description should never include things that can't be seen or heard on screen. This
includes describing characters feelings, thoughts or memories, unless they are shown on
screen. For example, if you wanted to show a memory the character has, you could use
dialogue or a flashback on screen, and if you wanted to show emotion/feelings you could use
tone of voice or body language.

2. It is a customary assumption in the movie industry that 1 page of screenplay is equivalent to 1
minute of time on screen. This is convenient for planning purposes since the average feature is
120 minutes, the average script should be around 120 pages.
Conventions of Master Scene Script include the font as courier and size 12, sluglines and
character names in dialogue are always wrote in capital letters, voiceover and offscreen used as
(V.O and O.S.), footers at the bottom right of a page say (CONTINUED) only where a scene
continues onto the next page. The next page will have (CONT.) in the top left.
When writing a spec script you shouldn't use scene numbers, camera angles, page footers,
capital letters for sound effects or character names (except first appearance) or third person
use of "we."
Shooting Script

3. Shooting scripts are mostly used during production to shoot the movie. They are written in a lot
more detail than a spec script because they can include things like scene numbers, editing
transitions and camera angles. For example, the shooting script above shows a scene number
before the second scene (not the first one because it's unnecessary) and has "CUT TO"
transitions in the bottom right of both scenes shown here. It also includes a voiceover using
(V.O.) and you can see when it ends and continues again due to the use of (CONT'D). Shooting
scripts are formatted to include any helpful information that the director may request. The
main difference between shooting scripts and screenplays are that shooting scripts not used for
selling purposes since they can be difficult to read and will turn off prospective investors,
whereas screenplays are.
Radio Script
Radio differs from film production due to the fact that nothing can be shown visually therefore
meaning there is much more dialogue. Below is an example of a radio script.

4. Unlike film scripts, radio scripts don't have any specific conventions around fonts and sizes
within the script. However, they use a lot of indiciations in the script to show how the actor
should be speaking.
For example, the script above uses (V.O.) a lot indicating that it is a voice over which is put over
music, which you can tell by the use of "MUSIC: ELO/MR BLUE SKIES (UNDER)" and "MUSIC:
OUT"
As well as that, the script uses things like "(Sighs)", "(Whispers)", and "(Groans)" to show
emotion and tone in the actors voices.
The script uses indications such as "(OFF)" which indicates the actor should speak away from
the microphone. The audio equivalent of off-screen. It also uses "(DISTORT)" which indicates a
character who is speaking via a mechanical device like a telephone or radio. There are other
indications used in radio scriptwriting that weren't shown in this example, such as "(LOW)"
which indicates the actor should speak quietly, and "(CLOSE)" which indicates that the actor
should be in close proximity to their individual microphone giving an intimate feel to the
dialogue.
Video Game Script
Video game scripts are different to both film and radio, in that they often exist within
interactive worlds with multiple options. Scripts are often branching which means there are
multiple options which may or may not have an impact later in the game.
When writing a video game script, you write it in 2 parts. The flowchart documents every major
decision the player faces and the result of that decision. It consists of text boxes with arrows to
indicate what happens when an action is performed. An example of this for Dark Souls II is
shown here which uses a legend.
(picture in better quality: https://i.imgur.com/4UeHK2J.jpg)

5. As you can see in this flowchart, it shows which areas lead where and uses a legend to show
different requirements for each area.
The second part of video game scripts is the actual script itself. Once all choices have been
defined in the flowchart, writers must compose scripts to take into account the variables their
world has created. This can be incredibly detailed and time-consuming depending on the
complexity and depth of the interactive world.
The script for Dark Souls II can be found here:
https://game-scripts.fandom.com/wiki/Dark_Souls_II
Video game scripts usually follow similar formats to filmscripts, however the variety in
gameplay means that there isn't one specific set format unlike the movie industry. Games may
often employ simple dialogue sheets that instruct a voice actor of exact phrases to say, and
how to project them. The Dark Souls II script shows the tone of voice in the script by using
words like "Err" and repeating letters like "W-welcome"