This document discusses occupational safety and health (OSH) regulations in India. It outlines the objectives of OSH which include maintaining worker well-being, preventing health issues from working conditions, and becoming familiar with occupational environments and needs. It also discusses the key provisions of the Factories Act of 1948 which establish regulations for cleanliness, waste disposal, ventilation, dust control, lighting, drinking water, sanitation facilities, machinery safety, and other factors important for worker health and safety. The document provides an overview of the important laws and regulations in India that govern workplace environmental protection, pollution control, and safety.
For Basic Concept of Factory law and some related Definition click on below link
https://www.slideshare.net/sheryshrivastava/factories-act1948-1
Section 11: Cleanliness
Section 12: Disposal of effluents and wastes
Section 13: Ventilation and Temperature
Section 14: Dust and Fume
Section 15: Artificial Humidification
Section 16: Overcrowding
Section 17: Lighting
Section 18: Drinking Water
Section 19: Latrines and Urinals
Section 20: Spittoons.
For Safety Measures of Factory Act click on below link
https://www.slideshare.net/sheryshrivastava/factories-act1948-part-3
For Basic Concept of Factory law and some related Definition click on below link
https://www.slideshare.net/sheryshrivastava/factories-act1948-1
Section 11: Cleanliness
Section 12: Disposal of effluents and wastes
Section 13: Ventilation and Temperature
Section 14: Dust and Fume
Section 15: Artificial Humidification
Section 16: Overcrowding
Section 17: Lighting
Section 18: Drinking Water
Section 19: Latrines and Urinals
Section 20: Spittoons.
For Safety Measures of Factory Act click on below link
https://www.slideshare.net/sheryshrivastava/factories-act1948-part-3
The Factories Act, 1948, regulates the hours of work and minimum wages. The Factories Act, 1948, mandates the payment of minimum wages to the workers by prescribing a fixed pay rate. An employer shall pay their employees at least the prescribed minimum wage rate.
The presentation is about factory act 1948. Here you will get all the information regarding Factory act 1948. The meaning, definition, provision of factory act 1948 regarding health and welfare of the workers and penalty procedure. Hope it will be informative for every one.
Provisions of Factories Act 1948,
Statutory Provisions under the Factories Act 1948,
Provisions Regarding the Health of Workers,
Provisions Regarding the Safety of Workers,
Provisions Regarding the Welfare of Workers,
Organized efforts and procedures for identifying workplace hazards and reducing accidents and exposure to harmful situations and substances. It also includes training of personnel in accident prevention, accident response, emergency preparedness, and use of protective clothing and equipment.
Couples presenting to the infertility clinic- Do they really have infertility...Sujoy Dasgupta
Dr Sujoy Dasgupta presented the study on "Couples presenting to the infertility clinic- Do they really have infertility? – The unexplored stories of non-consummation" in the 13th Congress of the Asia Pacific Initiative on Reproduction (ASPIRE 2024) at Manila on 24 May, 2024.
The Factories Act, 1948, regulates the hours of work and minimum wages. The Factories Act, 1948, mandates the payment of minimum wages to the workers by prescribing a fixed pay rate. An employer shall pay their employees at least the prescribed minimum wage rate.
The presentation is about factory act 1948. Here you will get all the information regarding Factory act 1948. The meaning, definition, provision of factory act 1948 regarding health and welfare of the workers and penalty procedure. Hope it will be informative for every one.
Provisions of Factories Act 1948,
Statutory Provisions under the Factories Act 1948,
Provisions Regarding the Health of Workers,
Provisions Regarding the Safety of Workers,
Provisions Regarding the Welfare of Workers,
Organized efforts and procedures for identifying workplace hazards and reducing accidents and exposure to harmful situations and substances. It also includes training of personnel in accident prevention, accident response, emergency preparedness, and use of protective clothing and equipment.
Couples presenting to the infertility clinic- Do they really have infertility...Sujoy Dasgupta
Dr Sujoy Dasgupta presented the study on "Couples presenting to the infertility clinic- Do they really have infertility? – The unexplored stories of non-consummation" in the 13th Congress of the Asia Pacific Initiative on Reproduction (ASPIRE 2024) at Manila on 24 May, 2024.
Title: Sense of Taste
Presenter: Dr. Faiza, Assistant Professor of Physiology
Qualifications:
MBBS (Best Graduate, AIMC Lahore)
FCPS Physiology
ICMT, CHPE, DHPE (STMU)
MPH (GC University, Faisalabad)
MBA (Virtual University of Pakistan)
Learning Objectives:
Describe the structure and function of taste buds.
Describe the relationship between the taste threshold and taste index of common substances.
Explain the chemical basis and signal transduction of taste perception for each type of primary taste sensation.
Recognize different abnormalities of taste perception and their causes.
Key Topics:
Significance of Taste Sensation:
Differentiation between pleasant and harmful food
Influence on behavior
Selection of food based on metabolic needs
Receptors of Taste:
Taste buds on the tongue
Influence of sense of smell, texture of food, and pain stimulation (e.g., by pepper)
Primary and Secondary Taste Sensations:
Primary taste sensations: Sweet, Sour, Salty, Bitter, Umami
Chemical basis and signal transduction mechanisms for each taste
Taste Threshold and Index:
Taste threshold values for Sweet (sucrose), Salty (NaCl), Sour (HCl), and Bitter (Quinine)
Taste index relationship: Inversely proportional to taste threshold
Taste Blindness:
Inability to taste certain substances, particularly thiourea compounds
Example: Phenylthiocarbamide
Structure and Function of Taste Buds:
Composition: Epithelial cells, Sustentacular/Supporting cells, Taste cells, Basal cells
Features: Taste pores, Taste hairs/microvilli, and Taste nerve fibers
Location of Taste Buds:
Found in papillae of the tongue (Fungiform, Circumvallate, Foliate)
Also present on the palate, tonsillar pillars, epiglottis, and proximal esophagus
Mechanism of Taste Stimulation:
Interaction of taste substances with receptors on microvilli
Signal transduction pathways for Umami, Sweet, Bitter, Sour, and Salty tastes
Taste Sensitivity and Adaptation:
Decrease in sensitivity with age
Rapid adaptation of taste sensation
Role of Saliva in Taste:
Dissolution of tastants to reach receptors
Washing away the stimulus
Taste Preferences and Aversions:
Mechanisms behind taste preference and aversion
Influence of receptors and neural pathways
Impact of Sensory Nerve Damage:
Degeneration of taste buds if the sensory nerve fiber is cut
Abnormalities of Taste Detection:
Conditions: Ageusia, Hypogeusia, Dysgeusia (parageusia)
Causes: Nerve damage, neurological disorders, infections, poor oral hygiene, adverse drug effects, deficiencies, aging, tobacco use, altered neurotransmitter levels
Neurotransmitters and Taste Threshold:
Effects of serotonin (5-HT) and norepinephrine (NE) on taste sensitivity
Supertasters:
25% of the population with heightened sensitivity to taste, especially bitterness
Increased number of fungiform papillae
Explore natural remedies for syphilis treatment in Singapore. Discover alternative therapies, herbal remedies, and lifestyle changes that may complement conventional treatments. Learn about holistic approaches to managing syphilis symptoms and supporting overall health.
Title: Sense of Smell
Presenter: Dr. Faiza, Assistant Professor of Physiology
Qualifications:
MBBS (Best Graduate, AIMC Lahore)
FCPS Physiology
ICMT, CHPE, DHPE (STMU)
MPH (GC University, Faisalabad)
MBA (Virtual University of Pakistan)
Learning Objectives:
Describe the primary categories of smells and the concept of odor blindness.
Explain the structure and location of the olfactory membrane and mucosa, including the types and roles of cells involved in olfaction.
Describe the pathway and mechanisms of olfactory signal transmission from the olfactory receptors to the brain.
Illustrate the biochemical cascade triggered by odorant binding to olfactory receptors, including the role of G-proteins and second messengers in generating an action potential.
Identify different types of olfactory disorders such as anosmia, hyposmia, hyperosmia, and dysosmia, including their potential causes.
Key Topics:
Olfactory Genes:
3% of the human genome accounts for olfactory genes.
400 genes for odorant receptors.
Olfactory Membrane:
Located in the superior part of the nasal cavity.
Medially: Folds downward along the superior septum.
Laterally: Folds over the superior turbinate and upper surface of the middle turbinate.
Total surface area: 5-10 square centimeters.
Olfactory Mucosa:
Olfactory Cells: Bipolar nerve cells derived from the CNS (100 million), with 4-25 olfactory cilia per cell.
Sustentacular Cells: Produce mucus and maintain ionic and molecular environment.
Basal Cells: Replace worn-out olfactory cells with an average lifespan of 1-2 months.
Bowman’s Gland: Secretes mucus.
Stimulation of Olfactory Cells:
Odorant dissolves in mucus and attaches to receptors on olfactory cilia.
Involves a cascade effect through G-proteins and second messengers, leading to depolarization and action potential generation in the olfactory nerve.
Quality of a Good Odorant:
Small (3-20 Carbon atoms), volatile, water-soluble, and lipid-soluble.
Facilitated by odorant-binding proteins in mucus.
Membrane Potential and Action Potential:
Resting membrane potential: -55mV.
Action potential frequency in the olfactory nerve increases with odorant strength.
Adaptation Towards the Sense of Smell:
Rapid adaptation within the first second, with further slow adaptation.
Psychological adaptation greater than receptor adaptation, involving feedback inhibition from the central nervous system.
Primary Sensations of Smell:
Camphoraceous, Musky, Floral, Pepperminty, Ethereal, Pungent, Putrid.
Odor Detection Threshold:
Examples: Hydrogen sulfide (0.0005 ppm), Methyl-mercaptan (0.002 ppm).
Some toxic substances are odorless at lethal concentrations.
Characteristics of Smell:
Odor blindness for single substances due to lack of appropriate receptor protein.
Behavioral and emotional influences of smell.
Transmission of Olfactory Signals:
From olfactory cells to glomeruli in the olfactory bulb, involving lateral inhibition.
Primitive, less old, and new olfactory systems with different path
Report Back from SGO 2024: What’s the Latest in Cervical Cancer?bkling
Are you curious about what’s new in cervical cancer research or unsure what the findings mean? Join Dr. Emily Ko, a gynecologic oncologist at Penn Medicine, to learn about the latest updates from the Society of Gynecologic Oncology (SGO) 2024 Annual Meeting on Women’s Cancer. Dr. Ko will discuss what the research presented at the conference means for you and answer your questions about the new developments.
ARTIFICIAL INTELLIGENCE IN HEALTHCARE.pdfAnujkumaranit
Artificial intelligence (AI) refers to the simulation of human intelligence processes by machines, especially computer systems. It encompasses tasks such as learning, reasoning, problem-solving, perception, and language understanding. AI technologies are revolutionizing various fields, from healthcare to finance, by enabling machines to perform tasks that typically require human intelligence.
New Directions in Targeted Therapeutic Approaches for Older Adults With Mantl...i3 Health
i3 Health is pleased to make the speaker slides from this activity available for use as a non-accredited self-study or teaching resource.
This slide deck presented by Dr. Kami Maddocks, Professor-Clinical in the Division of Hematology and
Associate Division Director for Ambulatory Operations
The Ohio State University Comprehensive Cancer Center, will provide insight into new directions in targeted therapeutic approaches for older adults with mantle cell lymphoma.
STATEMENT OF NEED
Mantle cell lymphoma (MCL) is a rare, aggressive B-cell non-Hodgkin lymphoma (NHL) accounting for 5% to 7% of all lymphomas. Its prognosis ranges from indolent disease that does not require treatment for years to very aggressive disease, which is associated with poor survival (Silkenstedt et al, 2021). Typically, MCL is diagnosed at advanced stage and in older patients who cannot tolerate intensive therapy (NCCN, 2022). Although recent advances have slightly increased remission rates, recurrence and relapse remain very common, leading to a median overall survival between 3 and 6 years (LLS, 2021). Though there are several effective options, progress is still needed towards establishing an accepted frontline approach for MCL (Castellino et al, 2022). Treatment selection and management of MCL are complicated by the heterogeneity of prognosis, advanced age and comorbidities of patients, and lack of an established standard approach for treatment, making it vital that clinicians be familiar with the latest research and advances in this area. In this activity chaired by Michael Wang, MD, Professor in the Department of Lymphoma & Myeloma at MD Anderson Cancer Center, expert faculty will discuss prognostic factors informing treatment, the promising results of recent trials in new therapeutic approaches, and the implications of treatment resistance in therapeutic selection for MCL.
Target Audience
Hematology/oncology fellows, attending faculty, and other health care professionals involved in the treatment of patients with mantle cell lymphoma (MCL).
Learning Objectives
1.) Identify clinical and biological prognostic factors that can guide treatment decision making for older adults with MCL
2.) Evaluate emerging data on targeted therapeutic approaches for treatment-naive and relapsed/refractory MCL and their applicability to older adults
3.) Assess mechanisms of resistance to targeted therapies for MCL and their implications for treatment selection
Acute scrotum is a general term referring to an emergency condition affecting the contents or the wall of the scrotum.
There are a number of conditions that present acutely, predominantly with pain and/or swelling
A careful and detailed history and examination, and in some cases, investigations allow differentiation between these diagnoses. A prompt diagnosis is essential as the patient may require urgent surgical intervention
Testicular torsion refers to twisting of the spermatic cord, causing ischaemia of the testicle.
Testicular torsion results from inadequate fixation of the testis to the tunica vaginalis producing ischemia from reduced arterial inflow and venous outflow obstruction.
The prevalence of testicular torsion in adult patients hospitalized with acute scrotal pain is approximately 25 to 50 percent
- Video recording of this lecture in English language: https://youtu.be/lK81BzxMqdo
- Video recording of this lecture in Arabic language: https://youtu.be/Ve4P0COk9OI
- Link to download the book free: https://nephrotube.blogspot.com/p/nephrotube-nephrology-books.html
- Link to NephroTube website: www.NephroTube.com
- Link to NephroTube social media accounts: https://nephrotube.blogspot.com/p/join-nephrotube-on-social-media.html
These simplified slides by Dr. Sidra Arshad present an overview of the non-respiratory functions of the respiratory tract.
Learning objectives:
1. Enlist the non-respiratory functions of the respiratory tract
2. Briefly explain how these functions are carried out
3. Discuss the significance of dead space
4. Differentiate between minute ventilation and alveolar ventilation
5. Describe the cough and sneeze reflexes
Study Resources:
1. Chapter 39, Guyton and Hall Textbook of Medical Physiology, 14th edition
2. Chapter 34, Ganong’s Review of Medical Physiology, 26th edition
3. Chapter 17, Human Physiology by Lauralee Sherwood, 9th edition
4. Non-respiratory functions of the lungs https://academic.oup.com/bjaed/article/13/3/98/278874
HOT NEW PRODUCT! BIG SALES FAST SHIPPING NOW FROM CHINA!! EU KU DB BK substit...GL Anaacs
Contact us if you are interested:
Email / Skype : kefaya1771@gmail.com
Threema: PXHY5PDH
New BATCH Ku !!! MUCH IN DEMAND FAST SALE EVERY BATCH HAPPY GOOD EFFECT BIG BATCH !
Contact me on Threema or skype to start big business!!
Hot-sale products:
NEW HOT EUTYLONE WHITE CRYSTAL!!
5cl-adba precursor (semi finished )
5cl-adba raw materials
ADBB precursor (semi finished )
ADBB raw materials
APVP powder
5fadb/4f-adb
Jwh018 / Jwh210
Eutylone crystal
Protonitazene (hydrochloride) CAS: 119276-01-6
Flubrotizolam CAS: 57801-95-3
Metonitazene CAS: 14680-51-4
Payment terms: Western Union,MoneyGram,Bitcoin or USDT.
Deliver Time: Usually 7-15days
Shipping method: FedEx, TNT, DHL,UPS etc.Our deliveries are 100% safe, fast, reliable and discreet.
Samples will be sent for your evaluation!If you are interested in, please contact me, let's talk details.
We specializes in exporting high quality Research chemical, medical intermediate, Pharmaceutical chemicals and so on. Products are exported to USA, Canada, France, Korea, Japan,Russia, Southeast Asia and other countries.
For Better Surat #ℂall #Girl Service ❤85270-49040❤ Surat #ℂall #Girls
kl1672014-140729101429-phpapp01.pdf
1. Occupational Safety
and Health (OSH)
The Factories Act, 1948 (Act No. 63 of 1948),
as amended by the Factories (Amendment) Act, 1987 (Act 20 of 1987)
3. The Objectives of OSH
•To maintain the physical, mental and social well-being of workers
•To prevent the unfavourable effects on health caused by working
conditions
•To become familiar to occupational environment of physical and
mental needs of workers
•To consider the issues relating to industrial safety, occupational
medicine, industrial hygiene, training & education, psychology and
so on.
5. SAFETY, HEALTH AND ENVIRONMENT GUIDELINES
• Rules & regulations followed in India are listed as follows:
• The Environment (Protection) Act, 1986
• The Environment (Protection) Rules, 1986
• Environmental Impact Assessment of Development Projects
1994
• The Prevention and control of pollution (uniform consent
procedure) Rules,1999
• Manufacture, Storage and Import of Hazardous chemicals
Rules,1989
• Manufacture, Storage and Import of Hazardous chemical
(Amendment) Rules,2000
SAFETY, HEALTH AND ENVIRONMENT GUIDELINES
6. SAFETY, HEALTH AND ENVIRONMENT GUIDELINES
• Hazardous Wastes (Management and Handling) Rules, 1989
• Bio-Medical Waste (Management and Handling) Rules, 1998
• Batteries (Management & Handling) Rules, 2000
• Ozone Depleting Substances (Regulation) Rules, 2000
• The Air (Prevention and Control of Pollution) Act, 1981 as
amended by Amendment Act, 1987
• The Air (Prevention and Control of Pollution) Act, 1982
• The Air (Prevention and Control of Pollution) Rules, 1982
• The Tamil Nadu Air ( Prevention and Control of Pollution )
Rules , 1983
7. SAFETY, HEALTH AND ENVIRONMENT GUIDELINES
• Noise Pollution (Regulation and Control) Rules, 2000
• The Water (Prevention and Control of Pollution) Act, 1974 as
amended in 1978 & 1988
• The Tamil Nadu Water ( Prevention and Control of Pollution )
Rules , 1983
• The Water(Prevention and Control of Pollution)Cess Act, 1977
as amended by Amendment Act, 1991
• The Water(Prevention and Control of Pollution)Cess Rules,
1978
• The Factories Act, 1948
SAFETY, HEALTH AND ENVIRONMENT GUIDELINES
8. • Tamilnadu Factories Rules, 1950
• The Gas Cylinders Rules, 1981
• The Indian Electricity Act, 1910
• The Indian Electricity Rules, 1956
• The Petroleum Act, 1934
• The Petroleum Rules, 1976
• The Public Liability Insurance Act, 1991
• The Public Liability Insurance Rules, 1991
• Hazardous Wastes (Management and Handling) Rules, 2000
SAFETY, HEALTH AND ENVIRONMENT GUIDELINES
SAFETY, HEALTH AND ENVIRONMENT GUIDELINES
9. Every factory shall be kept clean and free from effluvial
arising from any drain, privy or other nuisance, and in
particular- accumulation of dirt and refuse shall be
removed daily by effective method and disposed of in a
suitable manner
Section 11.Cleanliness
10. Section 12. Disposal of wastes and effluents
Effective arrangements shall be made in
every factory for the treatment of wastes and
effluents due to the manufacturing process
carried on therein, so as to render them
harmless, and for their disposal.
11. Section 13. Ventilation and temperature
(1) Effect and suitable provisions shall be made in every
factory for securing and maintaining in every workroom-
(a) adequate ventilation by the circulation of fresh air, and
(b) such a temperature as will secure to workers therein
reasonable conditions of comfort and prevent injury to
health; and in particular,
(i) walls and roofs shall be of such material and so designed
that such temperature shall not be exceeded but kept as
low as practicable;
12. Section 14. Dust and fume
(1) In every factory in which, by reason of the manufacturing process
carried on, there is given off any dust or fume or other impurity of
such a nature and to such an extent as is likely to be injurious or
offensive to the workers employed therein,
(2) or any dust in substantial quantities, effective measures shall be
taken to prevent its inhalation and accumulation in any workroom,
and if any exhaust appliance is necessary for this purpose, it shall
be applied as near as possible to the point of origin of the dust,
fume or other impurity, and such point shall be enclosed so far as
possible.
13. Section 15. Artificial humidification
(1) In respect of all factories in which
the humidity of the air is artificially
increased, the State Government
may make rules,-
(a) prescribing standards of
humidification;
(b) prescribing methods to be
adopted for securing adequate
ventilation and cooling of the air in
the workrooms.
(2) In any factory in which the humidity
of the air is artificially increased, the
water used for the purpose shall be
taken from a public supply, or other
source of drinking water, or shall he
effectively purified before it is so
used.
14. Section 16. Overcrowding
No room in any factory shall be
overcrowded to an extent injurious
to the health of the workers
employed therein.
Without prejudice to the generality of
sub-section (1), there shall be in
every workroom of a factory in
existence on the date of
commencement of this Act at least
9.9 cubic metres and of a factory
built after the commencement of
this Act
at least 14.2 cubic metres of space for
every worker employed therein, and
for the purposes of this sub-section
no account shall be taken of
anyspace which is more than 4.2
metres above the level of the floor
of the room.
15. Section 17. Lighting
1) In every part of a factory where
workers are working or passing, there
shall be provided and maintained
sufficient and suitable lighting, natural
or artificial, or both.
(2) In every factory all glazed windows
and skylights used for the lighting of
the workroom shall be kept clean on
both the inner and outer surfaces and,
so far as compliance with the
provisions of any rules made under
sub-section (3) of section 13 will allow,
free from obstruction.
(3) In every factory effective provision
shall, so far as is practicable, be made
for the prevention of-
(a) glare, either directly from a source of
light or by reflection from a smooth or
polished surface;
(b) the formation of shadows to such an
extent as to cause eye-strain or the
risk of accident to any worker.
16. Section 18. Drinking water
(1) In every factory effective arrangements shall be made to provide and
maintain at suitable points conveniently situated for all workers employed
therein a sufficient supply of wholesome drinking water.
(2) All such points shall be legibly marked "drinking water" in a language
understood by a majority of the workers employed in the factory and no
such points shall be situated within 1[six metres of any washing place,
urinal, latrine, spittoon, open drain carrying sullage or effluent or any
other source of contamination unless a shorter distance is approved in
writing by the Chief Inspector.
(3) In every factory wherein more than two hundred and fifty workers are
ordinarily employed, provisions shall be made for cooling drinking water
during hot weather by effective means and for distribution thereof.
17. Section 19. Latrines and urinals
1) In every factory-
(a) sufficient latrine and urinal accommodation of prescribed types shall be
provided conveniently situated and accessible to workers at all times while
they are at the factory;
(b) separate enclosed accommodation shall be provided for male and female
workers;
(c) such accommodation shall be adequately lighted and ventilated and no latrine
or urinal shall, unless specially exempted in writing by the Chief Inspector,
communicate with any workroom except through an intervening open space or
ventilated passage;
(d) all such accommodation shall be maintained in a clean and sanitary condition
at all times;
18. Section 20. Spittoons
In every factory there shall be provided a sufficient number of
spittoons in convenient places and they shall be maintained in a
clean and hygienic condition.
No person shall spit within the premises of a factory except in
the spittoons provided for the purpose and a notice containing
this provision and the penalty for its violation shall be
prominently displayed at suitable places in the premises.
19. Section 21. Fencing of machinery
(1) In every factory the following, namely-
(i) every moving part of a prime-mover and every
fiywheel connected to a prime-mover, whether the
prime-mover or flywheel is in the engine-house or
not;
(ii) the headrace and tailrace of every water-wheel and
water-turbine;
(iii) any part of a stock bar which projects beyond the
head stock of a lathe; and
(iv) unless they are in such position or of such
construction as to be safe to every person
employed in the factory as they would be if they
were securely fenced, the following, namely:-
(a) every part of an electric generator, a motor or
rotary convertor;
(b) every part of transmission machinery; and
(c) every dangerous part of any other machinery; shall
be securely fenced by safeguards of a substantial
construction which shall be constantly maintained
and kept in position while the parts of machinery
they are fencing, are in motion or in use:
20. Section 22. Work on or near machinery in motion
• (1) Where in any factory it becomes necessary to examine any part of machinery referred
to in section 21, while the machinery is in motion, or, as a result of such examination, to
carry out-
• (a) in a case referred to in clause (i) of the proviso to sub-section (1) of section 21,
lubrication or other adjusting operation; or
• (b) in a case referred to in clause (ii) of the proviso aforesaid, any mounting or shipping of
belts or lubrication or other adjusting operation,
• while the machinery is in motion, such - examination or operation shall be made or carried
out only by a specially trained adult male worker wearing tight fitting clothing (which shall
be supplied by the occupier) whose name has been recorded in the register prescribed in
this behalf and who has been furnished with a certificate of his appointment, and while he
is so engaged,-
21. Section 23. Employment of young persons on dangerous machines
(1) No young person shall be required or allowed to work at any machine to which this
section applies, unless he has been fully instructed as to the dangers arising in
connection with the machine and the precautions to be observed, and-
(a) has received sufficient training in work at the machine, or (b) is under adequate
supervision by a person who has a thorough knowledge and experience of the
machine.
(2) Sub-section (1) shall apply to such machines as may be prescribed by the State
Government, being machines which in its opinion are of such a dangerous
character that young persons ought not to work at them unless the foregoing
requirements are complied with.
22. Section 24. Striking gear and devices for cutting off power
(1) In every factory-
(a) suitable striking gear or other efficient mechanical appliance shall be provided and
maintained and used to move driving belts to and from fast (3) When a device, which
can inadvertently shift from "off" to "on" position, is provided in a factory- to cut off
power, arrangements shall be provided for locking the device in safe position to
prevent accidental starting of the transmission machinery or other machines to which
the device it fitted.
23. Section 25. Self-acting machines
No traversing part of a self-acting machine in any factory and no material
carried thereon shall, if the space over which it runs is a space over
which any person is liable to pass, whether in the course of his
employment or otherwise, be allowed to run on its outwards or inward
traverse within a distance forty-five centimetres from any fixed structure
which is not part of the machine:
24. Section 26. Casing of new machinery
(1) In all machinery driven by power and installed in any factory after the
commencement of this Act,-
(a) every set screw, bolt or key on any revolving shaft, spindle, wheel or pinion
shall be so sunk, encased or otherwise effectively guarded as to prevent
danger;
(b) all spur, worm and other toothed or friction gearing which does not require
frequent adjustment while in motion shall be completely encased, unless it
is so situated as to be as safe as it would be if it were completely encased.
25. Section 27. Prohibition of employment of women and children near
cotton-openers
No woman or child shall be employed in any part
of a factory for pressing cotton in which a cotton-
opener is at work:
26. Section 28. Hoist and lifts
(2) The following additional requirements shall apply to hoists and lifts used for carrying
persons and installed or reconstructed in a factory after the commencement of this Act,
namely:-
(a) where the cage is supported by rope or chain, there shall be at least two ropes or
chains separately connected with the cage and balance weight, and each rope or chain
with its attachments shall be capable of carrying the whole weight of the cage together
with its maximum load;
(b) efficient devices shall be provided and maintained capable of supporting the cage
together with its maximum load in the event of breakage of the ropes, chains or
attachments;
(c) an efficient automatic device shall be provided and maintained to prevent the cage from
over-running.
27. Section 29. Lifting machines, chains, ropes and lifting tackles
(1) In any factory the following provisions shall be complied with in respect of every
lifting machine (other than a hoist and lift) and every chain, rope and lifting tackle for
the purpose of raising or lowering persons, goods or materials:-
(a) all parts, including the working gear, whether fixed or movable, of every lifting
machine and every chain, rope or lifting tackle shall be-
(i) of good construction, sound material and adequate strength and free from defects;
(ii) properly maintained; and
(iii) thoroughly examined by a competent person at least once in every period of twelve
months, or at such intervals as the Chief Inspector may specify in writing, and a
register shall be kept containing the prescribed particulars of every such
examination;
28. Section 29. Lifting machines, chains, ropes and lifting tackles ….contd’
(3) For the purposes of this section a lifting
machine or a chain, rope or lifting tackle shall be
deemed to have been thoroughly examined if a
visual examination supplemented, if necessary,
by other means and by the dismantling of parts
of the gear, has been carried out as carefully as
the conditions permit in order to arrive at a
reliable conclusion as to the safety of the parts
examined.
Explanation.- In this section,-
(a) "lifting machine" means a crane, crab, winch,
teagle, pully block, gin wheel, transporter or
runway;
(b) "lifting tackle" means any chain sling, rope
sling, hook, shackle, swivel, coupling, socket,
clamp, tray or similar appliance, whether fixed
or movable, used in connection with the raising
or lowering of persons, or loads by use lifting
machines.
29. Section 30. Revolving machinery
(1) In every factory in which the process of grinding is carried on there shall be permanently
affixed to or placed ear each machine in use a notice indicating the maximum safe
working peripheral speed of every grindstone or abrasive wheel, the speed of the shaft or
spindle upon which the wheel is mounted, and the diameter of the pulley upon such shaft
or spindle necessary to secure such safe working peripheral speed.
(2) The speeds indicated in notices under sub-section (1) shall not be exceeded.
(3) Effective measure shall be taken in every factory to ensure that the safe working
peripheral speed of every revolving vessel, cage, basket, flywheel pulley, disc or similar
appliance driven by power is not exceeded.
30. Section 31. Pressure plant
(1) If in any factory, any plant or machinery or any part
thereof is operated at a pressure above atmospheric
pressure, effective measures shall be taken to ensure
that the safe working pressure of such plant or
machinery or part is not exceeded.
31. Section 32. Floors, stairs and means of access
In every factory-
(a) all floors, steps, stairs, passengers and gangways shall be of sound
construction, and properly maintained and shall be kept free from
obstructions and substances likely to cause persons to slip and where
it is necessary to ensure safety, steps, stairs, passages and gangways
shall be provided with substantial handrails;
(b) there shall, so far as is reasonably practicable, be provided, and
maintained safe means of access to every place at which any person
is at any time required to work;
(c) when any person has to work at a height from where he is likely to
fall, provision shall be made, so far as is reasonably practicable, by
fencing or otherwise, to ensure the safety of the person so working.
32. Section 33. Pits, sumps, openings in floors etc.,
(1) In every factory every fixed vessel, sump, tank, pit or opening
in the ground or in a floor which, by reason of its depth,
situation, construction or contents, is or may be a source of
danger, shall be either securely covered or securely fenced.
(2) The State Government may, by order in writing, exempt,
subject to such conditions as may be prescribed, any factory or
class or description of factories in respect of any vessel, sump,
tank, pit or opening from compliance with the provisions of this
section.
33. Section 34. Excessive weights
(1) No person shall be employed in any factory to lift, carry or move
any load so heavy as to be likely to cause him an injury.
(2) The State Government may make rules prescribing the maximum
weights which may be lifted, carried or moved by adult men, adult
women, adolescents and children employed in factories or in any
class or description of factories or in carrying on in any specified
process.
34. Section 35. Protection of eyes
In respect of any such manufacturing process carried on in any factory as
may be prescribed, being a process which involves-
(a) risk of injury to the eyes from particles or fragments thrown off in the
course of the process, or
(b) risk to the eyes by reason of exposure to excessive light, the State
Government may by rules require that effective screens or suitable
goggles shall be provided for the protection of persons employed on, or in
the immediate vicinity of, the process.
35. Section 36. Precautions against dangerous fumes, gases, etc
(1) No person shall be required or allowed to enter any chamber, tank, vat,
pit, pipe, flue or other confined space in any factory in which any gas,
fume, vapour or dust is likely to be present to such an extent as to involve
risk to persons being overcome thereby, unless it is provided with a
manhole of adequate size or other effective means of egress.
(2) No person shall be required or allowed to enter any confined space as is
referred to in sub-section (1), until all practicable measures have been
taken to remove any gas, fume, vapour or dust, which may be present so as
to bring its level within the permissible limits and to prevent any ingress of
such gas, fume, vapour or dust and unless-
36. Section 36A. Precautions regarding the use of portable electric light
In any factory-
(a) no portable electric light or any other electric appliance of
voltage exceeding twenty-four volts shall be permitted for use
inside any chamber, tank, vat, pit, pipe, flue or other confined
space unless adequate safety devices are provided; and
(b) if any inflammable gas, fume or dust is likely to be present in
such chambers tank, vat, pipe, flue or other confined space, no
lamp or light other than that of flame-proof construction shall be
permitted to be used therein
37. Section 37. Explosive or inflammable dust, gas, etc.,
• Where in any factory any manufacturing process produces dust, gas, fume or
vapour of such character and to such extent as to be likely to explode on
ignition, all practicable measures shall be taken to prevent any such
explosion by-
• (a) effective enclosure of the plant or machinery used in the process;
• (b) removal or prevention of the accumulation of such dust, gas, fume or
vapour;
• (c) exclusion or effective enclosure of all possible sources of ignition.
38. Section 38. Precautions in case of fire
(1) In every factory, all practicable measures shall be taken to prevent
outbreak of fire and its spread, both internally and externally, and to
provide and maintain-
(a) safe means of escape for all persons in the event of a fire, and
(b) the necessary equipment and facilities for extinguishing fire.
(2) Effective measures shall be taken to ensure that in every factory all
the workers are familiar with the means of escape in case of fire and
have been adequately trained in the routine to be following in such
cases.
39. Section 39. Power to require specifications of defective parts or tests of
stability
If it appears to the Inspector
that any building or part of a
building or any part of the
ways, machinery or plant in a
factory is in such a condition
that it may be dangerous to
human life or safety, he may
serve on the occupier or
manager or both of the factory
an order in writing requiring
him before a specified date-
(a) to furnish such drawings,
specifications and other
particulars as may be
necessary to determine
whether such buildings, ways,
machinery or plant can be used
with safety, or
(b) to carry out such tests in
such manner as may be
specified in the order, and to
inform the Inspector of the
results thereof.
40. Section 40. Safety of buildings and machinery
(1) If it appears to the Inspector that any building or part of a building or
any part of the ways, machinery or plant in a factory is in such a
condition that it is dangerous to human life or safety, he may serve on
the occupier or manager or both of the factory an order in writing
specifying the measures, which in his opinion should be adopted and
requiring them to be carried out before a specified date.
41. Section 40A. Maintenance of buildings
If it appears to the Inspector that any
building or part of a building in a factory
is in such a state of disrepair as is likely
to lead to conditions detrimental to the
health and welfare of the workers, he
may serve on the occupier or manager or
both of the factory an order in writing
specifying the measures which in his
opinion should be taken and requiring
the same to be carried out before such
date as is specified in the order.
42. (1) In every factory-
(i) wherein one thousand or more workers are ordinarily employed, or
(ii) wherein, in the opinion of the State Government, any
manufacturing process or operation is carried on, which process
or operation involves any risk of bodily injury, poisoning or disease
or any other hazard to health, to the person employed in the
factory,
Section 40B. Safety Officers
43. Section 41. Power to make rules to supplement this Chapter
• The State Government may make rules requiring the provision in any
factory or in any class or description of factories of such further
devices and measures for securing safety of persons employed
therein as it may deem necessary.
45. Cleaning of shop floor:
Keep clean and free from accumulation of dirt
and refuse daily
Cleaning of Machines:
Reduce accidents to keep machines cleaned
will
Housekeeping
46. Prevention of Leakage and spillage:
Use splash guards in machines and collecting tray
Disposal of Scrap-
Empty scrap, wastage, swarf from respective
containers regularly
Housekeeping
47. Tool Storage- Use special racks, holders
for respective tools
Storage Spaces: Identify storage areas
for respective items. Do not park material
in aisle.
Housekeeping
48. Piling Methods- Do not overload
platform, floor and keep material at safe
height.
Material handling: Use forklifts,
conveyors and hoist
Housekeeping
49. Good shop floor practices
Awareness to workers with daily target on manufacturing activities.
Display of Informative charts to post production, quality and safety
results compared to achievements.
Workers are trained on written product quality standards.
Manufactured parts are inspected to ensure adherence to quality
standards.
Production processes are planned by engineering to minimize product
variation.
50. Good shop floor practices
5S methods to organize the shop floor and production lines.
Workers trained on plant safety practices in line with OSH standards.
Workers trained on “root cause” analysis to resolve the causes of non-
conformances.
A written preventive maintenance plan for upkeep of Plant machinery &
equipment
Plant employees & Management meeting to get input on process
improvements.
Process Improvement Teams are employed to implement “best practices”
58. Disposal procedure of waste
materials
Be aware of what materials you are using and that they
can be properly disposed before beginning any project.
Large unused portions of material may be return to the
shared scrap areas so that leftover material may be used.
Chips and waste pieces from work surfaces and the floor
using a broom/brush and dust pan, or vacuum may be
removed.
Using compressed air is not an appropriate method
for cleaning chips off a surface as it promotes the
hazardous dispersion of particulate and chips into the
air and potentially into the eyes, hair, clothing and skin
of others in the Lab environment. chips are not to be
handled with bare hands/fingers.
59. Disposal procedure of waste
materials
Liquids such as paint, plaster, paint thinner, stain, wood sealer, resin, rubber,
solvents, and many other chemicals used in the industrial workshops are not
appropriate for sink disposal as they are potentially hazardous to natural and
drinking water systems.
Always posted procedures to be followed on Hazardous Waste Disposal
Hazardous Waste collection containers are to be located in appropriate places.
Each container is labelled with its appropriate contents and no material to be
disposed into a container that does not have its contents listed on the label.
60. Wood products (plywood, OSB, and solid wood)
can be recycled and the red bins in the Wood Shop
are available for this purpose.
Recyclable paper, cardboard that has been broken
down, and recyclable plastics should be discarded
in the blue recycle bins.
Any recyclable food containers should be clean
and free of liquids.
Non-recyclable plastics, acrylic/plexi, and plastic
sheet, MDF, masonite, and particle board must be
disposed of in the grey trash bins.
Sharp containers are to be used for the disposal of
cutting knife blades and other sharps.
Metal barrels in the Machine Shop and Metal Shop
are available for collection of scrap metal (steel,
copper, brass, aluminium, etc.)
Disposal procedure of waste
materials