Anexo 8 norma asme seccion VIII en españolRicardo Aranda
Este documento describe los métodos de examen por líquido penetrante (PT) que deben utilizarse. Establece los requisitos para la certificación del personal que realiza los exámenes PT, incluida su visión y competencia. También describe cómo evaluar las indicaciones encontradas durante los exámenes PT y establece las normas de aceptación para determinar si una pieza ha pasado o no el examen.
This document provides guidance on welding pressure pipelines and piping systems using shielded metal arc welding. It discusses procedures for vertical down welding of cross-country pipelines, including joint preparation, pipe cleaning, techniques for welding the root, hot, fill and cap passes. It also provides recommendations for current settings when using Lincoln engine driven welders and discusses troubleshooting root pass issues. The document recommends techniques for welding different types of pipe materials and strengths.
Soluforce reinforced-thermoplastic-pipes-espanolmarco parra
El documento proporciona información sobre SOLUFORCE® RLP, un sistema de tuberías reforzadas no metálicas para transporte de petróleo y gas. Se describe que SOLUFORCE® RLP está fabricado con materiales termoplásticos anticorrosivos y refuerzo de fibra de poliéster, y que incluye accesorios de conexión de acero inoxidable o termoplástico. También se detallan las especificaciones técnicas de los diferentes tamaños de tubería RLP, así como ventajas como bajo cost
This document provides information on the essential variables and requirements for welder qualification according to ASME Section IX. It lists the key variables that must be specified for a welder qualification, including welding process, type, base metal, filler metal, and weld thickness limits. It also outlines the qualification requirements and limitations for weld position, diameter, progression, backing, and which filler and base metals a welder is qualified to use based on their test.
1) O documento fornece tabelas técnicas com dados sobre motores de indução trifásicos e monofásicos, capacidade de condução elétrica de cabos e potência reativa a ser instalada em motores.
2) As tabelas incluem informações como corrente nominal, RPM, potência, rendimento e fator de potência para diferentes tipos e tamanhos de motores.
3) Valores como amperagem máxima de acordo com o tamanho dos cabos também são apresentados.
The internship report summarizes Abdul Hadi Chara's 30-day internship at MOL Pakistan's Central Processing Facility and Makori Gas Processing Facility. It provides an overview of the health and safety induction and descriptions of the well heads, valves, processing units and utilities at both facilities. It also includes assignments analyzing differences between compressor types, rich and lean burn engines, and the HVAC system. The report aims to document the knowledge and experience gained during the internship.
The document provides a hydro test procedure for newly constructed pipeline as part of the Berri Development Onshore Flowlines & Tie Ins Project in Saudi Arabia. It outlines responsibilities for the hydro test, describes test preparation including submittals required, testing components, and safety precautions. The procedure specifies filling the system with water, applying and maintaining test pressure, inspecting for leaks, and draining/drying upon completion.
This document provides specifications for flanges and bolts for piping systems. It includes tables with information on flange size, bolt quantity, stud size, and end-to-end length for different pipe sizes. The tables cover Class 150, 300, 400, 600 and 900 flanges under product lines such as Series A, B, and others.
Anexo 8 norma asme seccion VIII en españolRicardo Aranda
Este documento describe los métodos de examen por líquido penetrante (PT) que deben utilizarse. Establece los requisitos para la certificación del personal que realiza los exámenes PT, incluida su visión y competencia. También describe cómo evaluar las indicaciones encontradas durante los exámenes PT y establece las normas de aceptación para determinar si una pieza ha pasado o no el examen.
This document provides guidance on welding pressure pipelines and piping systems using shielded metal arc welding. It discusses procedures for vertical down welding of cross-country pipelines, including joint preparation, pipe cleaning, techniques for welding the root, hot, fill and cap passes. It also provides recommendations for current settings when using Lincoln engine driven welders and discusses troubleshooting root pass issues. The document recommends techniques for welding different types of pipe materials and strengths.
Soluforce reinforced-thermoplastic-pipes-espanolmarco parra
El documento proporciona información sobre SOLUFORCE® RLP, un sistema de tuberías reforzadas no metálicas para transporte de petróleo y gas. Se describe que SOLUFORCE® RLP está fabricado con materiales termoplásticos anticorrosivos y refuerzo de fibra de poliéster, y que incluye accesorios de conexión de acero inoxidable o termoplástico. También se detallan las especificaciones técnicas de los diferentes tamaños de tubería RLP, así como ventajas como bajo cost
This document provides information on the essential variables and requirements for welder qualification according to ASME Section IX. It lists the key variables that must be specified for a welder qualification, including welding process, type, base metal, filler metal, and weld thickness limits. It also outlines the qualification requirements and limitations for weld position, diameter, progression, backing, and which filler and base metals a welder is qualified to use based on their test.
1) O documento fornece tabelas técnicas com dados sobre motores de indução trifásicos e monofásicos, capacidade de condução elétrica de cabos e potência reativa a ser instalada em motores.
2) As tabelas incluem informações como corrente nominal, RPM, potência, rendimento e fator de potência para diferentes tipos e tamanhos de motores.
3) Valores como amperagem máxima de acordo com o tamanho dos cabos também são apresentados.
The internship report summarizes Abdul Hadi Chara's 30-day internship at MOL Pakistan's Central Processing Facility and Makori Gas Processing Facility. It provides an overview of the health and safety induction and descriptions of the well heads, valves, processing units and utilities at both facilities. It also includes assignments analyzing differences between compressor types, rich and lean burn engines, and the HVAC system. The report aims to document the knowledge and experience gained during the internship.
The document provides a hydro test procedure for newly constructed pipeline as part of the Berri Development Onshore Flowlines & Tie Ins Project in Saudi Arabia. It outlines responsibilities for the hydro test, describes test preparation including submittals required, testing components, and safety precautions. The procedure specifies filling the system with water, applying and maintaining test pressure, inspecting for leaks, and draining/drying upon completion.
This document provides specifications for flanges and bolts for piping systems. It includes tables with information on flange size, bolt quantity, stud size, and end-to-end length for different pipe sizes. The tables cover Class 150, 300, 400, 600 and 900 flanges under product lines such as Series A, B, and others.
This document discusses the selection of filler wires. It begins with an objective to learn about filler wires, ASME Section IX Table QW-422 for material grades and chemical compositions, and SFA numbers. It then introduces the differences between filler wires and electrodes, and the nomenclature used for filler wires. Examples are provided for selecting the correct filler wire based on the base metal, welding process, and referring to ASME standards. The conclusion emphasizes that filler wire selection depends on the welding process, base metal, joint type, and referencing ASME codes.
Este documento descreve os procedimentos para a obtenção manual de amostras representativas de produtos de petróleo em diferentes formatos, incluindo tanques, tubulações, tambores e fluxo livre. Ele fornece instruções detalhadas sobre fatores como ensaios analíticos, tipos de recipientes de amostra e procedimentos específicos para diferentes materiais. A tabela 1 resume os diferentes métodos de amostragem manual e suas aplicações correspondentes.
Este documento proporciona especificaciones técnicas para tubería de acero A53/A106 grado B, incluyendo diámetros disponibles de 1/4" a 24", espesores nominales, tolerancias dimensionales, propiedades mecánicas, y detalles sobre su aplicación para usos mecánicos y de presión.
Este documento establece el procedimiento de inspección por líquidos penetrantes. Describe las etapas de la inspección, incluyendo la limpieza de la superficie, la aplicación del líquido penetrante y revelador, y la interpretación de los resultados para detectar discontinuidades. El objetivo es garantizar un control de calidad en la detección de defectos superficiales en una variedad de materiales a través de esta técnica de inspección no destructiva.
Este documento es un catálogo de bridas forjadas producidas por FRANCOVIGH S.A. que incluye información sobre los tipos de bridas, normas aplicables, materiales, dimensiones y especificaciones de acuerdo a las series de presión. El catálogo provee detalles técnicos sobre bridas normalizadas y de gran diámetro para la industria petrolera, petroquímica, gasífera y minera.
2012 05 10 Materiales para Tanques GLP - 2da sesión parte 1Edgardo_AV
El documento describe los materiales permitidos para tanques de GLP según la normativa nacional e internacional. La normativa nacional establece que los tanques deben ser de acero fabricados de acuerdo al Código ASME Sección VIII División 1. El Código ASME especifica que los materiales deben cumplir con las especificaciones de la Sección II del código y limita los materiales a aceros al carbono y de baja aleación listados en la Tabla UCS-23. Las Tablas 1A, 1B y 3 de la Sección II proveen las tensiones
1) The document discusses how to read, understand, and use a Welding Procedure Specification (WPS). It provides definitions for key terms like WPS, PQR, essential variables, and non-essential variables.
2) A Procedure Qualification Record (PQR) must be made before a WPS. The PQR documents the variables used to weld a test coupon and the test results.
3) The example WPS provided is written according to ASME code for welding carbon steel designated as P-No. 8 material. It specifies the welding process, filler metal, and other key variables.
CLP in VLAREM door Philippe Cornille (essenscia)Voka-VEV
De VLAREM-trein 2013 komt aan. Op 28 maart 2014 organiseerde Voka i.s.m. essenscia een infosessie die de belangrijkste wijzigingen oplijst en extra toelichting geeft bij de aanpassingen VLAREM aan CLP.
This document provides an overview of Rahman Suwandhi's role and responsibilities as a Quality/Welding Engineer conducting inspections during offshore pipeline and platform installations. It outlines the required qualifications and certifications, describes the production and inspection workflow, and details the various inspection activities conducted, including material, welding, non-destructive testing (NDT), and painting/coating inspections. Specific areas of inspection focus are ensuring materials and welding meet requirements, using NDT methods to check weld joints, and controlling and monitoring coating quality. Relevant quality documents, codes/standards, inspection variables, and acceptance criteria are also summarized.
This document provides details of a welding procedure specification and welder qualification test, including the contract and document numbers, client, materials being welded, welding parameters for the root, hot, fill and final passes, and a visual inspection report. It lists the welding process, filler metal type and size, current, voltage, travel speed, heat input, and number of welders and electrodes used. The joint design, root and cap inspections, and approvals of the quality assurance coordinator and inspecting authority are also included.
Este documento describe el procedimiento para inspeccionar soldaduras y uniones mediante el método de líquidos penetrantes. Se especifican los criterios de aceptación y rechazo de defectos, así como el proceso de reparación y limpieza. El procedimiento incluye la aplicación de un penetrante, revelador y la inspección visual para identificar cualquier defecto superficial.
Este documento establece los procedimientos para el montaje de una planta chancadora en una obra de construcción y mejoramiento de carreteras. Describe las responsabilidades del personal involucrado, los equipos de protección personal requeridos, y los equipos, herramientas y materiales necesarios. Explica el proceso de montaje, incluyendo medidas de seguridad como inspeccionar el área de trabajo, usar señalización adecuada y no ubicarse en la línea de movimiento de los equipos.
Supervisión Proceso de habilitación de estructuras metálicas tipo pórtico, para sostenimiento de faja conveyor en interior de túnel en fase de operación
La termo fusión es un método de soldadura para tuberías de polietileno que involucra calentar las superficies a unir hasta su punto de fusión y aplicar presión. Se puede usar para diámetros de 20 mm a 3000 mm y es apropiado para uniones permanentes y seguras que rara vez presentan fugas. Las técnicas principales son la soldadura a tope, por enchufe y en "T" reducida, las cuales involucran calentar los extremos a unir y aplicar presión controlada.
El documento es un catálogo de válvulas de compuerta, globo y retención bonete bridado fundido fabricadas por Walworth. Describe los materiales, arreglos interiores, principales especificaciones de diseño y certificaciones de calidad de Walworth. Incluye información técnica sobre pruebas de calidad como radiografía, identificación de materiales, pruebas magnéticas y de fuego que realiza Walworth para garantizar el cumplimiento de normas internacionales.
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive functioning. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms.
This document appears to be a list of standards and guidelines related to engineering projects and industrial operations. It includes over 80 items grouped under subject areas like boiler assessments, dredging approvals, emission modeling, equipment life cycle costs, engineering drawings, risk-based inspections, pipeline installation and maintenance, process control systems, battery testing, welding procedures, protective systems design, field testing, fiber reinforced plastics, naturally occurring radioactive materials management, project planning, chemical screening, risk assessments, and preventive maintenance. The document provides standard codes for various technical specifications and procedures.
This document discusses the selection of filler wires. It begins with an objective to learn about filler wires, ASME Section IX Table QW-422 for material grades and chemical compositions, and SFA numbers. It then introduces the differences between filler wires and electrodes, and the nomenclature used for filler wires. Examples are provided for selecting the correct filler wire based on the base metal, welding process, and referring to ASME standards. The conclusion emphasizes that filler wire selection depends on the welding process, base metal, joint type, and referencing ASME codes.
Este documento descreve os procedimentos para a obtenção manual de amostras representativas de produtos de petróleo em diferentes formatos, incluindo tanques, tubulações, tambores e fluxo livre. Ele fornece instruções detalhadas sobre fatores como ensaios analíticos, tipos de recipientes de amostra e procedimentos específicos para diferentes materiais. A tabela 1 resume os diferentes métodos de amostragem manual e suas aplicações correspondentes.
Este documento proporciona especificaciones técnicas para tubería de acero A53/A106 grado B, incluyendo diámetros disponibles de 1/4" a 24", espesores nominales, tolerancias dimensionales, propiedades mecánicas, y detalles sobre su aplicación para usos mecánicos y de presión.
Este documento establece el procedimiento de inspección por líquidos penetrantes. Describe las etapas de la inspección, incluyendo la limpieza de la superficie, la aplicación del líquido penetrante y revelador, y la interpretación de los resultados para detectar discontinuidades. El objetivo es garantizar un control de calidad en la detección de defectos superficiales en una variedad de materiales a través de esta técnica de inspección no destructiva.
Este documento es un catálogo de bridas forjadas producidas por FRANCOVIGH S.A. que incluye información sobre los tipos de bridas, normas aplicables, materiales, dimensiones y especificaciones de acuerdo a las series de presión. El catálogo provee detalles técnicos sobre bridas normalizadas y de gran diámetro para la industria petrolera, petroquímica, gasífera y minera.
2012 05 10 Materiales para Tanques GLP - 2da sesión parte 1Edgardo_AV
El documento describe los materiales permitidos para tanques de GLP según la normativa nacional e internacional. La normativa nacional establece que los tanques deben ser de acero fabricados de acuerdo al Código ASME Sección VIII División 1. El Código ASME especifica que los materiales deben cumplir con las especificaciones de la Sección II del código y limita los materiales a aceros al carbono y de baja aleación listados en la Tabla UCS-23. Las Tablas 1A, 1B y 3 de la Sección II proveen las tensiones
1) The document discusses how to read, understand, and use a Welding Procedure Specification (WPS). It provides definitions for key terms like WPS, PQR, essential variables, and non-essential variables.
2) A Procedure Qualification Record (PQR) must be made before a WPS. The PQR documents the variables used to weld a test coupon and the test results.
3) The example WPS provided is written according to ASME code for welding carbon steel designated as P-No. 8 material. It specifies the welding process, filler metal, and other key variables.
CLP in VLAREM door Philippe Cornille (essenscia)Voka-VEV
De VLAREM-trein 2013 komt aan. Op 28 maart 2014 organiseerde Voka i.s.m. essenscia een infosessie die de belangrijkste wijzigingen oplijst en extra toelichting geeft bij de aanpassingen VLAREM aan CLP.
This document provides an overview of Rahman Suwandhi's role and responsibilities as a Quality/Welding Engineer conducting inspections during offshore pipeline and platform installations. It outlines the required qualifications and certifications, describes the production and inspection workflow, and details the various inspection activities conducted, including material, welding, non-destructive testing (NDT), and painting/coating inspections. Specific areas of inspection focus are ensuring materials and welding meet requirements, using NDT methods to check weld joints, and controlling and monitoring coating quality. Relevant quality documents, codes/standards, inspection variables, and acceptance criteria are also summarized.
This document provides details of a welding procedure specification and welder qualification test, including the contract and document numbers, client, materials being welded, welding parameters for the root, hot, fill and final passes, and a visual inspection report. It lists the welding process, filler metal type and size, current, voltage, travel speed, heat input, and number of welders and electrodes used. The joint design, root and cap inspections, and approvals of the quality assurance coordinator and inspecting authority are also included.
Este documento describe el procedimiento para inspeccionar soldaduras y uniones mediante el método de líquidos penetrantes. Se especifican los criterios de aceptación y rechazo de defectos, así como el proceso de reparación y limpieza. El procedimiento incluye la aplicación de un penetrante, revelador y la inspección visual para identificar cualquier defecto superficial.
Este documento establece los procedimientos para el montaje de una planta chancadora en una obra de construcción y mejoramiento de carreteras. Describe las responsabilidades del personal involucrado, los equipos de protección personal requeridos, y los equipos, herramientas y materiales necesarios. Explica el proceso de montaje, incluyendo medidas de seguridad como inspeccionar el área de trabajo, usar señalización adecuada y no ubicarse en la línea de movimiento de los equipos.
Supervisión Proceso de habilitación de estructuras metálicas tipo pórtico, para sostenimiento de faja conveyor en interior de túnel en fase de operación
La termo fusión es un método de soldadura para tuberías de polietileno que involucra calentar las superficies a unir hasta su punto de fusión y aplicar presión. Se puede usar para diámetros de 20 mm a 3000 mm y es apropiado para uniones permanentes y seguras que rara vez presentan fugas. Las técnicas principales son la soldadura a tope, por enchufe y en "T" reducida, las cuales involucran calentar los extremos a unir y aplicar presión controlada.
El documento es un catálogo de válvulas de compuerta, globo y retención bonete bridado fundido fabricadas por Walworth. Describe los materiales, arreglos interiores, principales especificaciones de diseño y certificaciones de calidad de Walworth. Incluye información técnica sobre pruebas de calidad como radiografía, identificación de materiales, pruebas magnéticas y de fuego que realiza Walworth para garantizar el cumplimiento de normas internacionales.
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive functioning. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms.
This document appears to be a list of standards and guidelines related to engineering projects and industrial operations. It includes over 80 items grouped under subject areas like boiler assessments, dredging approvals, emission modeling, equipment life cycle costs, engineering drawings, risk-based inspections, pipeline installation and maintenance, process control systems, battery testing, welding procedures, protective systems design, field testing, fiber reinforced plastics, naturally occurring radioactive materials management, project planning, chemical screening, risk assessments, and preventive maintenance. The document provides standard codes for various technical specifications and procedures.
Yanmar 4 tnv98 industrial engine service repair manualjksmermd
The document encourages the reader to click a link for more information after thanking them for reading. It provides a brief message asking the reader to click a link and states it will provide more information after they do so.
Yale c910 glc25 vx lift truck service repair manualjksmermd
The document provides a service manual for GLC20VS, GLC25VX, GLC30VX, GLC35VX lift trucks, with sections covering various systems and components. It describes the frame assembly, which includes the counterweight, fuel and hydraulic tanks. Procedures are provided for removing and installing the counterweight, hood, overhead guard, engine, and side covers. Maintenance technicians must take safety precautions like blocking the lift truck when removing heavy components to maintain stability.
Yale b974 gdp20 lx lift truck service repair manualjksmermd
This document provides instructions for removing and installing various components on the frame of GLP20LX, GLP25LX, GDP20LX, and GDP25LX lift trucks, including the hood, seat, side covers, dash panel, and electrical cover. The steps describe disconnecting wire harnesses, removing mounting hardware, and lifting parts off the frame. Safety warnings are provided about putting the trucks on blocks for stability when large heavy parts are removed.
Yale b910 glc35 vx lift truck service repair manualjksmermd
The document provides instructions for removing and installing the hood, seat, and side covers on various lift truck models. Key steps include:
1. Removing the floor mat, floor plate, side covers, dash, and kick panel to access the hood and seat.
2. Disconnecting the seat wire harness and removing 4 capscrews to lift the seat off the hood.
3. Removing hinge screws and gas springs to lift the hood off the frame.
4. Reinstalling follows the reverse order, ensuring the gas springs and hinge screws are securely fastened to specified torque values. Tables provide details on gas spring installation points for different seat and model configurations.
Toyota 30 7 fbcu30 forklift service repair manualjksmermd
This document is a service manual for the Toyota electric forklift models 7FBCU15 to 55 series from July 2001. It provides specifications, maintenance, repair, diagnostic and service procedures for the chassis, body, electrical controls, and material handling system.
The manual is intended to assist technicians in providing quick and correct servicing for the corresponding forklift models. It deals with models produced as of July 2001, but designs and specifications may have changed since then.
The manual is organized by section with topics including general information, the battery, multi-display functions, troubleshooting, the motor, drive unit, front and rear axles, steering, brakes, body, material handling system, mast,
Mercury mercruiser marine engine in line diesel d4.2 l d-tronic service repai...jksmermd
This document is the service manual for Mercury Marine in-line diesel engines. It provides general information on engine operation and maintenance procedures. The manual outlines maintenance schedules and procedures for engine systems including lubrication, cooling, fuel, and electrical systems. It also covers maintenance of drive systems and components. Photos show external views of the engine and components are labeled for identification.
Liebherr pr721 c crawler dozer service repair manualjksmermd
This document provides technical specifications for a PR 751 crawler dozer in three sections. It details the diesel engine, hydraulic and electrical systems, and general machine components. The diesel engine is an inline 6-cylinder intercooled and turbocharged unit producing 276 kW. The hydraulic system uses multiple gear pumps and motors to power travel, replacement, cooling and other circuits. General components include a 3-stage gear travel system, track undercarriage, and attachment specs.
Liebherr lr 622 lr622 crawler loader series 2 litronic service repair manualjksmermd
This document provides guidelines for the proper handling and disposal of service fluids and filters for LIEBHERR crawler dozers, loaders, and pipelayers. It discusses approved engine oils and their viscosity grades based on temperature, diesel fuel specifications, coolant requirements, and mixing ratios for winter diesel fuel. Instructions are given for disposing of used fluids and filters in an environmentally friendly manner according to regulations.
Jcb 3170 plus fastrac service repair manualjksmermd
Dacromet fasteners have lower torque settings than zinc plated fasteners due to their corrosion resistant coating. The document provides lists of torque settings for zinc plated and Dacromet fasteners of various sizes, along with some specific examples of component locations and their torque settings. Safety must come first when working on machines.
Jcb 2115 fastrac service repair manual sn:00740003 00740637jksmermd
The document provides information about torque settings for fasteners on JCB Fastrac machines. It distinguishes between zinc-plated fasteners and newer Dacromet fasteners, listing specific torque values for bolts of different sizes for each type. It also provides identifying information for machine components, a brief introduction to the service manual contents and layout, and safety warnings.
Jcb 722 fastrac service repair manual sn:00833001 00833111jksmermd
This document provides information about vehicle identification, torque settings for fasteners, service tools, sealing compounds, towing procedures, hydraulic hose connections, and hydraulic system contamination for a JCB articulated dump truck. It includes tables of torque specifications for different sizes and types of fasteners. Sections cover identifying the vehicle, engine, and transmission using identification plates and numbers. Procedures are outlined for connecting and disconnecting hydraulic hoses safely. Guidelines are provided for preventing and cleaning hydraulic system contamination.
Jcb 531 70 telescopic handler service repair manual sn:1522574 to tbajksmermd
This document is the service manual section 1 general information for JCB side engine loadall machines. It provides an introduction to the machines covered and applications tables listing which topics in the manual are applicable to each machine model. The tables cover sections 1 through 3 on general information, care and safety, and routine maintenance as well as sections B through K on specific systems.
Jcb 520 40 load control (supplement) service repair manualjksmermd
The LCS load control system provides protection against tipping forward by progressively reducing boom lowering and tilt functions as stability limits are approached. It has two modes - Load Control mode, which is automatic, and Ground Work mode, which functions like a standard LMI. In Load Control mode, boom lowering and tilt are derated, while extend functions normally until the limit. Once reached, lowering, tilting, crowding and dumping are prevented to avoid further instability. Boom lift and retract allow load retrieval. The system uses LED indicators and switches to monitor stability and select modes.
The document promotes clicking a link to obtain more information. It thanks the reader for their time and directs them to click a specified link in order to learn more details. The overall message is encouraging the reader to follow the given link by promising additional information will become available if they do.
Hitachi zaxis 240 lch excavator service repair manualjksmermd
- This document provides safety guidelines for operating heavy machinery.
- It instructs operators to wear protective equipment, secure seat belts, avoid distractions, and only start the engine from the operator's seat.
- Operators are also advised to be aware of bystanders and not allow riders on the machine for their safety.
2009 arctic cat m1000 sno pro 162 ltd snowmobiles service repair manualjksmermd
This document contains specifications and technical information for Arctic Cat snowmobiles. It includes sections on identification numbers, recommended fuels and oils, break-in procedures, storage procedures, maintenance schedules, engine specifications, electrical specifications, torque specifications, and more. High altitude operation is discussed, noting that components like carburetion and clutches may need adjustment for optimal performance at different elevations.
2003 yamaha viking vk 540 series snowmobile service repair manualjksmermd
This chapter covers periodic inspections and adjustments for various vehicle systems. A maintenance table outlines recommended checks and services to perform every 20, 40, 80 hours or seasonally, including inspecting bolts, belts, brakes, carburetor settings, engine components and ignition timing. Detailed procedures then provide guidance on adjusting items like idle speed, cable play, pump stroke, sheave distance and more.
2003 yamaha sx viper 700 service repair manualjksmermd
This document provides instructions and specifications for the periodic inspection, adjustment, and maintenance of various systems for a snowmobile, including the chassis, powertrain, engine, cooling system, carburetion, electrical, and specifications. It emphasizes the importance of thorough cleaning, using proper tools, keeping mated parts together, and following torque specifications for repairs. It also provides details on machine identification numbers, replacement parts, handling of gaskets, seals, bearings, circlips, and use of Loctite for fasteners.
Hitachi ex5600 6 ld excavator service repair manual
1.
2. INTRODUCTION
IN-01
ADDITIONAL REFERENCES
Please refer to the other materials (operator’s
manual, parts catalog, engine technical material
and Hitachi training material etc.) in addition to this
manual.
MANUAL COMPOSITION
This manual consists the Technical Manual and the
Workshop Manual.
• Information included in the Technical Manual:
technical information needed for redelivery and
delivery, operation and activation of all devices
and systems, operational performance tests, and
troubleshooting procedures.
• Information included in the Workshop Manual:
technical information needed for maintenance
and repair of the machine, tools and devices
needed for maintenance and repair, maintenance
standards, and removal/installation and assem-
ble/disassemble procedures.
PAGE NUMBER
Each page has a number, located on the center
lower part of the page, and each number contains
the following information:
Example : T 1-3-5
Consecutive Page Number for Each Group
Group Number
Section Number
T: Technical Manual W: Workshop Manual
3. INTRODUCTION
IN-02
SAFETY ALERT SYMBOL AND HEADLINE
NOTATIONS
In this manual, the following safety alert symbol and
signal words are used to alert the reader to the
potential for personal injury of machine damage.
This is the safety alert symbol. When you see this
symbol, be alert to the potential for personal injury.
Never fail to follow the safety instructions prescribed
along with the safety alert symbol.
The safety alert symbol is also used to draw attention
to component/part weights.
To avoid injury and damage, be sure to use appropri-
ate lifting techniques and equipment when lifting
heavy parts.
CAUTION:
Indicated potentially hazardous situation which
could, if not avoided, result in personal injury or
death.
IMPORTANT:
Indicates a situation which, if not conformed to the
instructions, could result in damage to the machine.
NOTE:
Indicates supplementary technical information or
know-how.
UNITS USED
SI Units (International System of Units) are used in
this manual.
MKSA system units and English units are also
indicated in parenthheses just behind SI units.
Example : 24.5 MPa (250 kgf/cm
2
, 3560 psi)
A table for conversion from SI units to other system
units is shown below for reference purposees.
Quantity
To Convert
From
Into Multiply By
MPa kgf/cm2
10.197Pressure
MPa psi 145.0
kW PS 1.360Power
kW HP 1.341
Temperature C F C 1.8+32
km/h mph 0.6214Velocity
min-1
rpm 1.0
Flow rate L/min US gpm 0.2642
mL/rev cc/rev 1.0
Quantity
To Convert
From
Into Multiply By
mm in 0.03937Length
mm ft 0.003281
L US gal 0.2642
L US qt 1.057
Volume
m3
yd3
1.308
Weight kg lb 2.205
N kgf 0.10197Force
N lbf 0.2248
N m kgf m 0.10197Torque
N m lbf ft 0.7375