Vanaf 1 november 2014 geldt voor de schakelkast de norm NEN-EN-IEC 61439-1. Tijdens de sessie worden alle EMC-kenmerken, genoemd in bijlage J van deze norm, besproken.
Aan de hand van een installatie wordt de bijlage J van deze norm vertaald naar de praktijk en geven we aanbevelingen en tips. Na afloop heeft u inzicht hoe u een schakelkast EMC-technisch moet bouwen en zonder beproevingen kunt verifiëren.
The document discusses low voltage switches and DIN-type HRC fuse links ranging from 2A to 1600A and voltages of 500V and 690V. It provides technical specifications, ordering information, time-current and cut-off current characteristics for gG-type and aM-type fuse links. The fuse links are suitable for overload and short circuit protection in distribution systems and motor circuits.
The document provides a summary of the single line diagram of the 132kv S/S PGIA substation. It has 3 incoming 132kv lines from the 400/220kv Sarojini Nagar substation and 1 outgoing 132kv line. The incoming lines pass through lightning arrestors and insulated discs before connecting to the gantry and circuit breakers. The line then passes through potential transformers and current transformers before connecting to the main bus bar. From the bus bar, the line is distributed to the 132kv bay and transformers through isolators. The substation also includes a 33kv substation with 2 40MVA transformers, 33kv bus bars, and bays. It describes the purpose of components like capacitor banks, isol
AC Circuit Breakers Routine Tests according to IEC 62271-100Ali Sepehri
AC Circuit Breakers Routine Tests according to IEC 62271-100
Article direct link: https://www.linkedin.com/pulse/ac-circuit-breakers-routine-tests-according-iec-ali-sepehri/
The Tradition and Science of Window Installations - Where are We Headed with ...Graham Finch
Presentation on the impact of more highly insulated and passive house wall designs and practices on the installation of windows. Presented at the 2016 Euroline technology forum.
This document provides testing and commissioning procedures for electrical installations in government buildings in Hong Kong. It outlines the objectives, scope, and specific procedures for testing and commissioning works. The objectives are to verify proper functioning of equipment/systems and that performance meets design intent. Scope includes preliminary steps, testing during construction, statutory testing and inspection, functional performance testing, and documentation. Specific procedures are provided for tests of low voltage and high voltage installations, as well as functional tests of various systems. Contractors must follow these procedures and submit documentation and certificates of testing and commissioning.
Underground cable components include copper core cables approximately 150mm in diameter, made up of various insulating layers, housed in groups of three in trenches approximately 1.1m deep. Joints are required every 500-800m and sealing end compounds are needed at each end. Access and preparation requires a 65m working area cleared of vegetation with temporary fencing and trackways. Cables are laid by excavators in trenches reinforced with timber and surrounded by cement bound sand, then covered after jointing. Reinstatement returns the area to its original condition and inspection every 3 years monitors the cables.
In three single phase high voltage underground cable induce voltages and currents in their sheaths. The sheath induced currents are undesirable and generate power losses and reduce the cable ampacity whereas the induced voltages can generate electric shocks to the workers that keep the power line. This means that when dealing with three single phase high voltage underground cable, it is very important to know the sheath currents called circulating currents that can circulate throughout the sheath and sheath voltage of the cables. It is very useful to know their values and the technique to reduce the sheath voltage of the high voltage Cable. This study presents as technique known as Mixed bonding technique combination of cross bonding and single point bonding to reduce the sheath voltage of the long length cable route. Manish Kumar | Ameen Uddin Ahmad"Mixed Bonding Method of High Voltage Cable" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-1 | Issue-5 , August 2017, URL: http://www.ijtsrd.com/papers/ijtsrd2348.pdf http://www.ijtsrd.com/engineering/electrical-engineering/2348/mixed-bonding-method-of-high-voltage-cable/manish-kumar
The document discusses low voltage switches and DIN-type HRC fuse links ranging from 2A to 1600A and voltages of 500V and 690V. It provides technical specifications, ordering information, time-current and cut-off current characteristics for gG-type and aM-type fuse links. The fuse links are suitable for overload and short circuit protection in distribution systems and motor circuits.
The document provides a summary of the single line diagram of the 132kv S/S PGIA substation. It has 3 incoming 132kv lines from the 400/220kv Sarojini Nagar substation and 1 outgoing 132kv line. The incoming lines pass through lightning arrestors and insulated discs before connecting to the gantry and circuit breakers. The line then passes through potential transformers and current transformers before connecting to the main bus bar. From the bus bar, the line is distributed to the 132kv bay and transformers through isolators. The substation also includes a 33kv substation with 2 40MVA transformers, 33kv bus bars, and bays. It describes the purpose of components like capacitor banks, isol
AC Circuit Breakers Routine Tests according to IEC 62271-100Ali Sepehri
AC Circuit Breakers Routine Tests according to IEC 62271-100
Article direct link: https://www.linkedin.com/pulse/ac-circuit-breakers-routine-tests-according-iec-ali-sepehri/
The Tradition and Science of Window Installations - Where are We Headed with ...Graham Finch
Presentation on the impact of more highly insulated and passive house wall designs and practices on the installation of windows. Presented at the 2016 Euroline technology forum.
This document provides testing and commissioning procedures for electrical installations in government buildings in Hong Kong. It outlines the objectives, scope, and specific procedures for testing and commissioning works. The objectives are to verify proper functioning of equipment/systems and that performance meets design intent. Scope includes preliminary steps, testing during construction, statutory testing and inspection, functional performance testing, and documentation. Specific procedures are provided for tests of low voltage and high voltage installations, as well as functional tests of various systems. Contractors must follow these procedures and submit documentation and certificates of testing and commissioning.
Underground cable components include copper core cables approximately 150mm in diameter, made up of various insulating layers, housed in groups of three in trenches approximately 1.1m deep. Joints are required every 500-800m and sealing end compounds are needed at each end. Access and preparation requires a 65m working area cleared of vegetation with temporary fencing and trackways. Cables are laid by excavators in trenches reinforced with timber and surrounded by cement bound sand, then covered after jointing. Reinstatement returns the area to its original condition and inspection every 3 years monitors the cables.
In three single phase high voltage underground cable induce voltages and currents in their sheaths. The sheath induced currents are undesirable and generate power losses and reduce the cable ampacity whereas the induced voltages can generate electric shocks to the workers that keep the power line. This means that when dealing with three single phase high voltage underground cable, it is very important to know the sheath currents called circulating currents that can circulate throughout the sheath and sheath voltage of the cables. It is very useful to know their values and the technique to reduce the sheath voltage of the high voltage Cable. This study presents as technique known as Mixed bonding technique combination of cross bonding and single point bonding to reduce the sheath voltage of the long length cable route. Manish Kumar | Ameen Uddin Ahmad"Mixed Bonding Method of High Voltage Cable" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-1 | Issue-5 , August 2017, URL: http://www.ijtsrd.com/papers/ijtsrd2348.pdf http://www.ijtsrd.com/engineering/electrical-engineering/2348/mixed-bonding-method-of-high-voltage-cable/manish-kumar
ABB Medium Voltage MV Indoor and Outdoor Current Transformers
ABB POWER PRODUCTSABB CT's - Current Transformers
ABB Medium Voltage MV Indoor Bushing Current Transformers CT's, 3.3kV to 11kV/12kV - ABB TTR
ABB Medium Voltage MV Indoor Bushing Current Transformers CT's, up to 25kV - ABB TTR
ABB Medium Voltage MV Indoor Current Transformers CT's, 3.3kV up to 40.5kV - ABB TPU
ABB Medium Voltage MV Indoor Current Transformers CT's, up to 25kV - ABB TPE
ABB Medium Voltage MV Outdoor Current Transformers CT's - ABB KON-17
ABB Medium Voltage MV Outdoor Current Transformers CT's, 17.5kV 24kV 25kV- ABB TPO6
Este documento describe métodos para estimar la energía calorífica incidente sobre un trabajador durante un arco eléctrico. Explica que existen dos normas principales, NFPA 70E y IEEE 1584, que proporcionan ecuaciones para calcular esta energía en función de parámetros como la corriente y tensión de la instalación. También presenta un método genérico. Finalmente, recomienda medidas preventivas como disminuir la corriente o tensión, o aumentar la distancia al arco, para reducir el riesgo térmico asoci
The document provides specifications for medium voltage current transformers (CTs) from ABB. It describes key technical parameters including voltage ratings from 3.6 to 12 kV, current ratings from 10 to 3200A, accuracy classes, dimensions, weights, and standards compliance. The CTs can be single or multi-turn, with reconnectable primary or secondary terminals. Dimensions, drawings, and weights are provided for various transformer types.
The document provides an overview of circuit breakers, including:
1) Circuit breakers sense overcurrent, measure its magnitude, and trip in a timely manner to prevent damage. They can be manually reset once a fault is cleared.
2) Key components include the frame, contacts, arc chute assembly, operating mechanism, and trip unit.
3) The trip unit senses overloads and short circuits and triggers the operating mechanism to open the contacts.
Este documento presenta un índice detallado de un libro sobre canalizaciones y conducciones eléctricas. El índice describe secciones sobre la instalación de canalizaciones, materiales y accesorios utilizados, prácticas resueltas y fichas de trabajo, con figuras ilustrativas para cada tema. El documento proporciona una guía completa sobre los contenidos cubiertos en el libro relacionados con el diseño, materiales y montaje de sistemas de canalizaciones eléctricas.
The document provides an overview of instrumentation valves and manifolds from AS-Schneider Group. It describes their E Series valves and manifolds which include a variety of valve head unit options, connections, hand valves, gauge valves, multiport gauge valves, and manifolds. The general features section outlines the available body materials, pressure testing, certifications, and material traceability of the products.
Este documento describe un sistema de puesta a tierra (SPAT) instalado en una antena de telecomunicaciones ubicada en una torre. Explica que un SPAT consiste en conectar un conductor eléctrico a tierra para proteger equipos eléctricos de descargas. Luego, proporciona un ejemplo real de un SPAT instalado en una antena y sus componentes como el electrodo de puesta a tierra, el punto de enlace y la línea de tierra. Finalmente, concluye que los SPAT se diseñan para crear planes preventivos
The document discusses improvements and new features in Yokogawa Electric Corporation's CENTUM CS 3000 process automation software. CENTUM CS 3000 R3.07 focuses on enhancing integration capabilities and the human-machine interface. New features include improved migration tools, expanded PROFIBUS DP support, enhanced integration with plant asset management systems, and an updated HMI with multi-monitor support. The updates aim to increase visibility of real-time plant data and diagnostic information across different systems.
El documento describe el transistor bipolar (BJT), uno de los dispositivos semiconductores más importantes. Explica que el BJT fue desarrollado por Walter Brattain y John Bardeen en 1947 y consiste en dos capas de material tipo n o p con una capa intermedia de material opuesto. También define al BJT como un dispositivo de tres terminales (emisor, base y colector) que puede amplificar señales de voltaje utilizando pequeñas señales de entrada para controlar elementos que requieren mayor señal.
Este documento presenta los sustentos de varias reglas del Código Nacional de Electricidad relacionadas al cálculo de cargas eléctricas para viviendas unifamiliares. Explica cómo calcular la máxima demanda considerando la carga básica, cargas adicionales, cargas de calefacción, cocinas eléctricas y calentadores de agua, según las áreas de las viviendas. También provee ejemplos numéricos para ilustrar los cálculos requeridos.
Este documento presenta una tabla de la capacidad amperimétrica de barras rectangulares de cobre para armarios eléctricos según la Norma DIN 46433. La tabla se basa en una temperatura ambiente de 35°C, una temperatura de barra de 65°C y una densidad de corriente aproximada de 1000 A/pulg2. Además, indica que las barras se pintarán con códigos de colores específicos y que si se perforan las barras de sujeción, se incrementará su dimensión para mantener la densidad
This document provides information on medium voltage HRC fuses. It describes the key features of HRC fuse-links, which have high rupturing capacity and can limit short-circuit currents. The fuse-links are used to protect transformers, capacitor banks, cables, and overhead lines. The document discusses fuse-link and fuse-base types, specifications, applications, selection criteria based on rated voltage and current, installation guidelines, and compliance with various standards.
A switchyard exists at power generating stations to coordinate power exchange between generators and transmission lines. Gas insulated switchgear (GIS) uses pressurized sulfur hexafluoride gas to insulate conductors and equipment, allowing for more compact and reliable switchyards. Key advantages of GIS include reduced space requirements, protection from weather, easier installation, and lower maintenance needs compared to traditional air insulated switchyards. While initial costs of GIS are higher, the long lifespan and reduced lifetime costs make GIS a more cost-effective option overall.
This PPT is based upon my training in Yokogawa Chennai.
Reference:
# Yokogawa Hand Book on CS 3000
# http://www.slideshare.net/bvent2005/dcs-presentation
This document discusses Profibus networking for industrial automation projects. It covers project delivery and engineering services including system architecture design, network design, component selection, installation, testing and verification. It also provides information on Profibus topology, networking components, segment design, fieldbus data sheets, design tools, integration documents and certified Profibus training in the UK.
The document describes the RM6 gas insulated ring main unit (GIS RMU) product line. Key points include:
- The RM6 is a compact switchgear that integrates medium voltage (MV) functional units like switch-disconnectors, circuit breakers, and fuse switches to enable connection, supply, and protection of transformers on ring or radial networks up to 24 kV.
- It provides reliability, simplicity, and safety through gas insulation in a sealed-for-life tank, minimizing maintenance needs. Extensions can be added on-site without handling gas.
- Schneider Electric has over 1.3 million RM6 devices installed worldwide, offering experience, quality control according to ISO standards, and
1. Fieldbus networks replace traditional 4-20 mA analog signals with digital communication over twisted-pair wiring.
2. The key changes are replacing the analog control system and field devices with digital ones that communicate over FOUNDATION fieldbus, and adding terminators to the wire pairs.
3. Devices can be connected in a bus, tree, daisy chain, or point-to-point topology with optional repeaters, bridges or gateways to extend the network or connect different segments.
This document summarizes a thesis on modeling metal oxide surge arresters using ATP-EMTP. It discusses two common models for metal oxide surge arresters: the IEEE model and the Pinceti model. It presents the modeling results for two arresters using each model and compares the percentage errors between the modeled and actual arrester performance data. The conclusion is that both models can predict arrester behavior with less than 10-14% error depending on the impulse current waveform. The IEEE model has higher errors than the Pinceti model for standard waves, while the Pinceti model has higher errors for steep waves.
This document provides a report on the 220KV/66KV New Receiving Station substation. It includes a single line diagram, power flow chart, descriptions of the main equipment including transformers, circuit breakers, batteries, control room, and earthing systems. The substation handles about 3 million units per day with a peak load of 176MW. It receives power at 220KV and steps it down to 66KV and 11KV to feed local distribution.
ABB Medium Voltage MV Indoor and Outdoor Current Transformers
ABB POWER PRODUCTSABB CT's - Current Transformers
ABB Medium Voltage MV Indoor Bushing Current Transformers CT's, 3.3kV to 11kV/12kV - ABB TTR
ABB Medium Voltage MV Indoor Bushing Current Transformers CT's, up to 25kV - ABB TTR
ABB Medium Voltage MV Indoor Current Transformers CT's, 3.3kV up to 40.5kV - ABB TPU
ABB Medium Voltage MV Indoor Current Transformers CT's, up to 25kV - ABB TPE
ABB Medium Voltage MV Outdoor Current Transformers CT's - ABB KON-17
ABB Medium Voltage MV Outdoor Current Transformers CT's, 17.5kV 24kV 25kV- ABB TPO6
Este documento describe métodos para estimar la energía calorífica incidente sobre un trabajador durante un arco eléctrico. Explica que existen dos normas principales, NFPA 70E y IEEE 1584, que proporcionan ecuaciones para calcular esta energía en función de parámetros como la corriente y tensión de la instalación. También presenta un método genérico. Finalmente, recomienda medidas preventivas como disminuir la corriente o tensión, o aumentar la distancia al arco, para reducir el riesgo térmico asoci
The document provides specifications for medium voltage current transformers (CTs) from ABB. It describes key technical parameters including voltage ratings from 3.6 to 12 kV, current ratings from 10 to 3200A, accuracy classes, dimensions, weights, and standards compliance. The CTs can be single or multi-turn, with reconnectable primary or secondary terminals. Dimensions, drawings, and weights are provided for various transformer types.
The document provides an overview of circuit breakers, including:
1) Circuit breakers sense overcurrent, measure its magnitude, and trip in a timely manner to prevent damage. They can be manually reset once a fault is cleared.
2) Key components include the frame, contacts, arc chute assembly, operating mechanism, and trip unit.
3) The trip unit senses overloads and short circuits and triggers the operating mechanism to open the contacts.
Este documento presenta un índice detallado de un libro sobre canalizaciones y conducciones eléctricas. El índice describe secciones sobre la instalación de canalizaciones, materiales y accesorios utilizados, prácticas resueltas y fichas de trabajo, con figuras ilustrativas para cada tema. El documento proporciona una guía completa sobre los contenidos cubiertos en el libro relacionados con el diseño, materiales y montaje de sistemas de canalizaciones eléctricas.
The document provides an overview of instrumentation valves and manifolds from AS-Schneider Group. It describes their E Series valves and manifolds which include a variety of valve head unit options, connections, hand valves, gauge valves, multiport gauge valves, and manifolds. The general features section outlines the available body materials, pressure testing, certifications, and material traceability of the products.
Este documento describe un sistema de puesta a tierra (SPAT) instalado en una antena de telecomunicaciones ubicada en una torre. Explica que un SPAT consiste en conectar un conductor eléctrico a tierra para proteger equipos eléctricos de descargas. Luego, proporciona un ejemplo real de un SPAT instalado en una antena y sus componentes como el electrodo de puesta a tierra, el punto de enlace y la línea de tierra. Finalmente, concluye que los SPAT se diseñan para crear planes preventivos
The document discusses improvements and new features in Yokogawa Electric Corporation's CENTUM CS 3000 process automation software. CENTUM CS 3000 R3.07 focuses on enhancing integration capabilities and the human-machine interface. New features include improved migration tools, expanded PROFIBUS DP support, enhanced integration with plant asset management systems, and an updated HMI with multi-monitor support. The updates aim to increase visibility of real-time plant data and diagnostic information across different systems.
El documento describe el transistor bipolar (BJT), uno de los dispositivos semiconductores más importantes. Explica que el BJT fue desarrollado por Walter Brattain y John Bardeen en 1947 y consiste en dos capas de material tipo n o p con una capa intermedia de material opuesto. También define al BJT como un dispositivo de tres terminales (emisor, base y colector) que puede amplificar señales de voltaje utilizando pequeñas señales de entrada para controlar elementos que requieren mayor señal.
Este documento presenta los sustentos de varias reglas del Código Nacional de Electricidad relacionadas al cálculo de cargas eléctricas para viviendas unifamiliares. Explica cómo calcular la máxima demanda considerando la carga básica, cargas adicionales, cargas de calefacción, cocinas eléctricas y calentadores de agua, según las áreas de las viviendas. También provee ejemplos numéricos para ilustrar los cálculos requeridos.
Este documento presenta una tabla de la capacidad amperimétrica de barras rectangulares de cobre para armarios eléctricos según la Norma DIN 46433. La tabla se basa en una temperatura ambiente de 35°C, una temperatura de barra de 65°C y una densidad de corriente aproximada de 1000 A/pulg2. Además, indica que las barras se pintarán con códigos de colores específicos y que si se perforan las barras de sujeción, se incrementará su dimensión para mantener la densidad
This document provides information on medium voltage HRC fuses. It describes the key features of HRC fuse-links, which have high rupturing capacity and can limit short-circuit currents. The fuse-links are used to protect transformers, capacitor banks, cables, and overhead lines. The document discusses fuse-link and fuse-base types, specifications, applications, selection criteria based on rated voltage and current, installation guidelines, and compliance with various standards.
A switchyard exists at power generating stations to coordinate power exchange between generators and transmission lines. Gas insulated switchgear (GIS) uses pressurized sulfur hexafluoride gas to insulate conductors and equipment, allowing for more compact and reliable switchyards. Key advantages of GIS include reduced space requirements, protection from weather, easier installation, and lower maintenance needs compared to traditional air insulated switchyards. While initial costs of GIS are higher, the long lifespan and reduced lifetime costs make GIS a more cost-effective option overall.
This PPT is based upon my training in Yokogawa Chennai.
Reference:
# Yokogawa Hand Book on CS 3000
# http://www.slideshare.net/bvent2005/dcs-presentation
This document discusses Profibus networking for industrial automation projects. It covers project delivery and engineering services including system architecture design, network design, component selection, installation, testing and verification. It also provides information on Profibus topology, networking components, segment design, fieldbus data sheets, design tools, integration documents and certified Profibus training in the UK.
The document describes the RM6 gas insulated ring main unit (GIS RMU) product line. Key points include:
- The RM6 is a compact switchgear that integrates medium voltage (MV) functional units like switch-disconnectors, circuit breakers, and fuse switches to enable connection, supply, and protection of transformers on ring or radial networks up to 24 kV.
- It provides reliability, simplicity, and safety through gas insulation in a sealed-for-life tank, minimizing maintenance needs. Extensions can be added on-site without handling gas.
- Schneider Electric has over 1.3 million RM6 devices installed worldwide, offering experience, quality control according to ISO standards, and
1. Fieldbus networks replace traditional 4-20 mA analog signals with digital communication over twisted-pair wiring.
2. The key changes are replacing the analog control system and field devices with digital ones that communicate over FOUNDATION fieldbus, and adding terminators to the wire pairs.
3. Devices can be connected in a bus, tree, daisy chain, or point-to-point topology with optional repeaters, bridges or gateways to extend the network or connect different segments.
This document summarizes a thesis on modeling metal oxide surge arresters using ATP-EMTP. It discusses two common models for metal oxide surge arresters: the IEEE model and the Pinceti model. It presents the modeling results for two arresters using each model and compares the percentage errors between the modeled and actual arrester performance data. The conclusion is that both models can predict arrester behavior with less than 10-14% error depending on the impulse current waveform. The IEEE model has higher errors than the Pinceti model for standard waves, while the Pinceti model has higher errors for steep waves.
This document provides a report on the 220KV/66KV New Receiving Station substation. It includes a single line diagram, power flow chart, descriptions of the main equipment including transformers, circuit breakers, batteries, control room, and earthing systems. The substation handles about 3 million units per day with a peak load of 176MW. It receives power at 220KV and steps it down to 66KV and 11KV to feed local distribution.
Workshop EMC - veldgebonden EMC voor industriële installaties volgens EMC-richtlijn 2004/108/EG
Actuele kennis geeft een voorsprong. Wanneer u op de hoogte bent van het totale programma kasten van Rittal, bent u in staat om direct zonder tijdverlies de juiste keuze te maken. Er is bovendien de meest efficiënte manier om uw kennisniveau op het gebied van EMC naar een hoger niveau te tillen.
De workshop gaat uitgebreid in op cruciale aspecten. Zoals het uitvoeren van veldmetingen, waarmee u de elektromagnetische beïnvloeding door portofoons, verlichting en mobiele telefonie (gsm) in kaart brengt. Aandacht hierbij voor materiaalkeuze, aarding, opbouw kast en beschermklasse volgens IP. Ook maken we u vertrouwd met dempingsmetingen, waarmee u de invloed van uitsparingen in een kast aantoont. Daarbij gaan we in op de samenhang tussen de CE-markering en de EMC-richtlijnen inclusief de nieuwe EMC-Richtlijn 2004/108/EG.
Verder leggen we het accent op het maken van een stappenplan: denk hierbij aan montageplaatindeling, kabelinvoer en installatie-opbouw overeenkomstig NPR-IEC/TR 61000-5-2 de praktijkrichtlijn EMC-installatie en aarding.
Phoenix Contact, workshop EMC – installatietechniek volgens de huidige EMC-ri...Cito Benelux
De workshop EMC geeft aan de hand van een industriële installatieopstelling inzicht in de elektromagnetische aspecten van deze installatie. Hierbij worden veldmetingen uitgevoerd om de elektrische en magnetische veldsterkte te meten. Daarna worden de stoorstromen in de installatie in beeld gebracht. Aan de hand van diverse optimaliseringsmaatregelen worden, met behulp van vergelijkbare metingen, verbeteringen zichtbaar gemaakt.
Phoenix Contact, Themamiddag Alles over bliksembeveiligingCito Benelux
Blikseminslag en overspanningen kunnen grote gevolgen hebben voor de beschikbaarheid van uw (productie)proces. Een effectief beveiligingsconcept kan deze risico's tot een minimum reduceren. De norm voor bliksem- en overspanningsbeveiliging NEN-EN-IEC 62305, is hierbij de basis voor een betrouwbaar beveiligingssysteem.
Deze themadag wordt in samenwerking met Schaap Bliksembeveiliging en Ontstoringstechniek bv en Van der Heide georganiseerd.
An emergency stop system is intended to avert or reduce hazards to people and equipment. It initiates an immediate shutdown through a single human action when a normal stopping process is not fast enough. Emergency stop buttons are designed for quick, simple activation even by untrained people. They should be located for easy access by operators but not endanger users. Emergency stops can be either uncontrolled power removal stops or controlled power-available stopping, depending on the system and potential hazards. Regulations require redundant, independent emergency stop circuits to ensure reliable stopping even with single failures.
Power Quality, de moderne kijk op stroom en spanningCito Benelux
Power Quality, de moderne kijk op stroom en spanning
Onder Power Quality wordt zowel de betrouwbaarheid als de kwaliteit van spanning en stroom verstaan. Elke onderbreking, dip of vervorming kan storend werken.
Doelen
Na afloop van deze workshop heeft u meer inzicht in Power Quality verkregen door de metingen in de installatie. Deze workshop is aan te bevelen voor iedereen die meer wil weten over de moderne kijk op spanning en stroom en daarmee over Power Quality
Inhoud
- Moderne fenomenen: harmonischen - dips - flikker
Dit kan de levensduur en/of de werking van apparatuur negatief beïnvloeden. Bovendien kunnen transformatoren, kabels en motoren oververhit raken of zelfs verbranden. Ook het hinderlijke flikkeren van verlichting kan te verwijten zijn aan onvoldoende kwaliteit van spanning en stroom. Belangrijke aspecten die de Power Quality in een installatie bepalen zijn harmonischen, dips, flikker, onbalans en inschakelverschijnselen.
-Wat zijn de spelregels: geldende normen
De minimale voorgeschreven kwaliteitseisen zijn voor Nederland vastgelegd in de Netcode met een verwijzing naar de norm NEN-EN-50160. De apparatuur in de installatie moet voldoen aan de eisen welke vastgelegd zijn in een IEC-61000 normenreeks. Om tot een goede verantwoorde Power Quality in de installatie te komen is het van belang dat de installateur hier kennis van heeft en doeltreffende maatregelen neemt.
Betrouwbaarheid, verificatie en validatie van veiligheidscircuits voor de machinebouw volgens PL. De meeste machines en productielijnen zijn uitgerust met noodstopcircuits en veiligheidsbesturingen, met daarin onder meer lichtschermen, deurschakelaars en laserscanners.
Zelfstandig engineeren conform NEN-EN-IEC 61439-1 in één middag
Sinds 1 november 2014 dienen alle distributie- en besturingskasten volgens deze nieuwe norm opgebouwd te worden. Uitgangspunt is een nog veiliger installatie die technisch goed te onderbouwen is. Met name de temperatuurhuishouding speelt hierbij een belangrijke rol. In dit seminar gaan we in op alle technische- en praktische aspecten omtrent stroomverdeling/laagspanningsverdeelinrichtingen die hierbij een rol spelen. Niet alleen de techniek wordt behandeld, ook efficiency, doorlooptijd en kosten komen ter sprake. Kortom, na dit seminar weet u alles omtrent stroomverdeling en ontwerpen volgens NEN-EN-IEC 61439-1.
1 sermes brochure frequentieregelaars en softstarters v1.8SERMES Nederland
Frequentieregelaars
Het programma van frequentieregelaars begint bij 0,18 tot 160 kW. Verdeelt over U/f regelkarakteristiek tot Sensorless Vector Control en regelaars met beide mogelijkheden.
Tevens levert SRERMES haar VARALMO elektromotoren met opgebouwde frequentie regelaar van 0,37 t/m 22 kW.
Deze de-centrale wijze van frequentiesturing bij elektromotoren maakt deze methode uitermate geschikt voor regeling van pompen of ventilatoren.
Validatie en Calibratie van lasapparatuur volgens EN1090 / 3834 / 50504Jorg Eichhorn
Presentatie van Frank van Doornik over validatie en calibratie van lasappartuur. Wat beschrijft de norm? Zijn (digitale) Volt en Ampere meters verplicht? Waarvoor kunt u terecht bij een ESAB validatie center.
Meer en meer worden internet en mobiel internet toegepast om industriële applicaties op afstand te beheren of om data op afstand op te vragen en te loggen. Het spreekt voor zich dat security hierbij een belangrijk aandachtspunt is.
Industriële netwerkarchitectuur
Het samengaan van IT en automatiseringsnetwerken brengt heel wat teweeg op de industriële werkvloer. Het implementeren van Ethernet gebaseerde netwerken in de productiehallen creëert de mogelijkheid naar doorgedreven implementaties op gebied van monitoring, MES, en ERP en biedt mogelijkheden om op afstand toegang te hebben tot het productieproces. Dit brengt ook de nodige bedreigingen met zich mee. De grootste bedreigingen zijn meestal verkeerde netwerkarchitectuur, toegepaste hardware welke niet altijd geschikt is om in een open omgeving zoals Ethernet TCP/IP ingezet te worden, gebrek aan kennis op de industriële werkvloer, …
Doelen
Na afloop van deze themadag bent u bekend met de basisbegrippen omtrent Ethernet TCP/IP, benodigde hardware, creëren van hiërarchische netwerken, gebruik van VLAN etc.
Een interessante dag voor iedereen die op de industriële werkvloer in aanraking komt met Ethernet gebaseerde oplossingen binnen de industriële wereld.
Inhoud
-basis LAN-technologie -bedraad LAN
-draadloos LAN
-industriële switches
-industriële AP's
-basisbegrippen TCP/IP -IP protocol
-TCP protocol
-ondersteunende protocollen
-industriële router
-implementatie -algemene aandachtspunten
-logische scheiding van netwerken d.m.v. VLAN
-fysische scheiding van netwerken d.m.v. industriële routers
-PROFINET RT
Phoenix Contact, Themadag draadloze netwerken in de industrieCito Benelux
Draadloze netwerken in de industrie – betrouwbaar werken met WiFi, Bluetooth en Trusted Wireless
Draadloze netwerken evolueren in een hoger tempo dan PC’s: van enkele Kbit/s naar meerdere Gbit/s in 15 jaar. Dat biedt mogelijkheden voor toepassingen waar we tot voor kort nog vast zaten aan bekabelde technieken. Maar draadloze netwerken zijn wel iets anders dan een traditioneel netwerk maar zonder kabels.
Omdat industrieel WiFi in veel opzichten hetzelfde is als het gewone WiFi, profiteert uw netwerk thuis ook van de op deze dag opgedane kennis.
Doelen
Na afloop van deze themadag is de deelnemer bekend met de mogelijkheden van de draadloze technieken WiFi, Bluetooth en Trusted Wireless. Er is voldoende kennis opgedaan om een keuze voor een technologie te maken bij een industriële toepassing.
Inhoud
-inleiding
-engineering van draadloze netwerken: antennes, vermogensbudgettering
-storingsbronnen, foutdetectie en foutreparatie
-specifieke mogelijkheden en kenmerken van Bluetooth, WiFi en Trusted Wireless
-cybersecurity van draadloze netwerken
-afsluiting met overzicht draadloze technieken
Rittal, Workshop Klimatisering in de praktijk - zelf aan de slag met ThermCito Benelux
Leer in één middag het programma Therm.
De nieuwe IEC 61439 gaat eind 2014 van kracht. Hierin staat voorgeschreven dat het gebouwde paneel niet te warm mag worden en dit moet onderbouwt zijn. Hierbij is Therm een handige tool.
De tijdrovende berekening van de klimaatiseringsbehoefte wordt volledig door de kosteloze software Therm overgenomen. De eenvoudig te bedienen software zorgst snel voor de juiste klimaatbeheersingscomponenten. Met een goede klimatisering in uw paneel, verbeterd u de levensduur van uw componenten en zorgt u voor minder storingen in uw proces.
Tijdens deze workshop laten we alle mogelijkheden van het programma zien en gaat u zelf aan de slag. Na afloop van de workshop bent u in staat zelf berekeningen uit te voeren en een document hiervan te genereren.
Rittal, Themadag Het praktijkgericht samenstellen van besturingskasten voor d...Cito Benelux
Themadag Het praktijkgericht samenstellen van besturingskasten voor de Ex zones
Explosies kunnen zich overal voordoen waar er sprake is van productie, verwerking, overslag van verf, olie- en smeermiddelen, batterijen en accu's, textiel, meel, graan, melkpoeder, suiker, zaagsel, mest reinigingsmiddelen en plastic.
De procesautomatisering in deze Ex zones wordt veelal geregeld vanuit de besturingskasten die staan in de Ex zones. Ondanks uw basiskennis over toepassingen in Ex zones, is het in de
praktijk niet inzichtelijk hoe deze besturingskasten overeenkomstig de ATEX-richtlijn samengesteld moeten worden. De vertaling naar explosieveilige producten binnen de wettelijke kaders van de ATEX-richtlijn wordt gemaakt.
Tijdens deze themadag ontvangt u op dit gebied praktische informatie over de technische ontwikkelingen en regelgeving. Aan de hand van een aantal aansprekende cases passen we de geleerde regelgeving toe.
In een ontspannen sfeer kunt u netwerken met collegae uit de industrie, ervaringen uitwisselen en doet u ideeën op betreffende Ex toepassingen voor uw bedrijfssituatie.
Deze dag organiseren wij samen met de firma Bartec.
Themadag Gestructureerd Programmeren - IEC 61131-3 garandeert een enorme boost aan uw efficiency
Het programmeervak in Nederland staat op een hoogniveau. Toch is een extra kwaliteitsimpuls mogelijk door te programmeren volgens de IEC 61131-3. Het juist hanteren van deze norm biedt zowel voor de programmeur als opdrachtgever meer efficiency en kwaliteit.
Wie overstapt op IEC 61131-3 boekt op termijn belangrijke winst. IEC 61131-3 standaardiseert alles wat met programmeertalen te maken heeft. Software kan men hierdoor op een gestructureerde wijze opbouwen. Modificaties en uitbreidingen kunnen zo sneller uitgevoerd worden.
Op de themadag krijgt u praktijkgerichte informatie van gespecialiseerde technici. Niet alleen van Phoenix Contact maar ook van Bert van der Linden, schrijver van een boek over gestructureerd programmeren volgens IEC 61131-3 en werkzaam bij de firma ATS. Hij maakt u bewust van de gevaren van ‘vrij programmeren’ én van de voordelen van IEC 61131-3. Ook is er aandacht voor de programmeersoftware van Phoenix Contact die voldoet aan de norm.
Workshop IT-powered AUTOMATION - multifunctionele besturingen
In deze workshop leert u hoe u kleine tot middelgrote automatiseringsuitdagingen voordelig kunt automatiseren en in uw bedrijfsnetwerk kunt integreren.
De compacte besturing ILC 150 ETH biedt u hiervoor de perfecte oplossing en onderscheidt zich niet alleen door modulaire uitbreidingsmogelijkheden, eenvoudige programmering en een hoge performance. Dankzij open automatiserings- en IT-interfaces zoals Interbus, Ethernet TCP/IP, FTP, SNMP of HTTP, laat deze compacte besturing zich naadloos in nagenoeg elk netwerk integreren.
Overtuig u zelf van deze communicatieve mogelijkheden en leer hoe eenvoudig de compacte besturing en de onboard web-server kunnen worden geprogrammeerd. Ook zult u in deze workshop ervaren hoe eenvoudig de Ethernetcommunicatie met een grafisch panel kan worden gerealiseerd, de PLC via een GSM-modem SMS-jes kan versturen en hoe er data tussen de PLC en een applicatie op een PC kan worden uitgewisseld!
Geef u snel op voor deze inspirerende workshop, ontdek de voordelen van deze compacte besturing en ga na de workshop direct aan de slag met de gratis starterkit!
In deze workshop leert u:
• De PLC programmeren volgens IEC 61131
• De PLC web-server programmeren
• Hoe de communicatie tussen de PLC en een grafisch panel, een PC en een GSM-modem via Ethernetgerealiseerd kan worden.
De gratis starterkit bestaat uit:
• Inline Controller ILC 150 ETH
• Voeding STEP –PS-100-240AC/25DC/1.5
• Inline-analoge uitgangsklem IB IL AO 1/U/SF-PAC
• Inline-analoge ingangsklem IB IL AI 2/SF-ME
• Programmeersoftware PC WORX
• CD-rom “Starterkit ILC 150 ETH” incl. documentatie en voorbeeldprogramma
Voorkennis:
• In deze workshops gaan we er van uit uit dat u enige ervaring heeft met het programmeren van PLC's in het algemeen. Indien u dit niet heeft dan vragen wij u dit aan te geven in het 'Vragen, wensen of opmerkingen' veld. Wij nemen dan contact met u op om voor u een speciale training te organiseren.
Aantal deelnemers: maximaal 12 personen
Kosten: € 795,00 inclusief gratis starterkit
2. • 260 werknemers in de Benelux
• Omzet:> € 120 mln.
• Financieel-,automatiserings en personeelsmanagement
• Facilitair
• Logistiek- en kwaliteitsmanagement
• Education
Cito Benelux
1/90
3. Kennis & Kunde
• Klimaatbeheersing
• Stroomverdeling
• Voedselveiligheid
• Securty
• Safety
• IT Powered automation
• Power Quality
• Elektromagnetische compatibiliteit
Cito Benelux
Cito Benelux
Kennis & Kunde
2/90
4. 5
Belangrijkste wijzigingen:
• Indeling
• Algemeen deel
• Specifieke delen
• Wijzigingen met betrekking verificatiemethoden
• Testen
• Berekenen
• Ontwerpregels
• Verdeelinrichtingen
• Geen PTTA en TTA categorieën
• Specifieke controle, ontwerp- routinecontrole
• Herziening van de desbetreffende EMC-eisen
Structuur
Laagspanningsschakel- en verdeelinrichtingen
• Deel 1: Algehele eisen schakel- en verdeelsystemen
• Deel 2: Vermogen schakel- en verdeelsystemen
• Deel 3: Schakel- en verdeelsystemen voor gebruik in ruimtes toegankelijk voor ondeskundig
personeel – Verdeelborden
• Deel 4: Bouwkasten
• Deel 5: Verdeelkasten in openbare netwerken
• Deel 6: Railkokersystemen
• Deel 7: Schakel- en verdeelsystemen voor gebruik op campings, jachthavens, marktplaatsen
e.d. (ook laadstations elektrische auto’s): nog niet klaar
NEN-EN-IEC
61439-1
NEN-EN-IEC
61439-5
NEN-EN-IEC
61439-4
NEN-EN-IEC
61439-3
NEN-EN-IEC
61439-2
Algemene eisen
Productdelen
NEN-EN-IEC
61439-6
NEN-EN-IEC
61439-7
NEN-EN-IEC 61439-1
3/90
8. Classificatie elektromagnetische omgevingen
13
Omgeving A: Gevoed door hoog- of middenspanningstransformator
Omgeving B: Gevoed door openbaar laagspanningsnet
• Industriële, wetenschappelijke en medische uitrusting.
• Zware inductieve of capacitieve belastingen die frequent worden
geschakeld
• Sterke stromen en bijbehorende krachtige magneetvelden
• Woonomgevingen
• Omgeving detailhandel
• Zakelijke gebouwen
NEN-EN-IEC 61439-1
Laagspanningsschakel-en-verdeelinrichtingen
EMC conform
14
Omgeving A: Gevoed door hoog- of middenspanningstransformator
• Algemene norm IEC 61000-6-2
• Algemene norm IEC 61000-6-4
NEN-EN-IEC 61439-1
Laagspanningsschakel-en-verdeelinrichtingen
EMC conform
Emissie- en Immuniteitseisen
7/90
9. 15
Omgeving A: Gevoed door hoog- of middenspanningstransformator
Omgeving B: Gevoed door openbaar laagspanningsnet
• Algemene norm IEC 61000-6-1
• Algemene norm IEC 61000-6-3
• Algemene norm IEC 61000-6-2
• Algemene norm IEC 61000-6-4
NEN-EN-IEC 61439-1
Laagspanningsschakel-en-verdeelinrichtingen
EMC conform
Emissie- en Immuniteitseisen
16
• De geïntegreerde toestellen en componenten zijn conform de EMC-eisen voor
de opgegeven omgeving
• De inwendige installatie en bedrading zijn uitgevoerd volgens de aanwijzingen
van de fabrikant van de componenten.
Er zijn geen immuniteits- of emissieproeven vereist als:
In alle andere gevallen moet de
conformiteit aan de EMC-eisen
worden geverifieerd door
beproeving.
NEN-EN-IEC 61439-1
Laagspanningsschakel-en-verdeelinrichtingen
EMC conform
Emissie- en Immuniteitseisen
8/90
10. 17
Te stellen eisen.
• De geïntegreerde toestellen en componenten zijn conform de EMC-eisen voor
de opgegeven omgeving
Er zijn geen immuniteits- of emissieproeven vereist als:
In alle andere gevallen moet de conformiteit aan de EMC-eisen
worden geverifieerd door beproeving.
NEN-EN-IEC 61439-1
Laagspanningsschakel-en-verdeelinrichtingen
EMC conform
IEC 61000-6-2
Immuniteit Industrie
IEC 61000-6-4
Emissie Industrie
18
Er zijn geen immuniteits- of emissieproeven vereist als:
In alle andere gevallen moet de conformiteit aan de EMC-eisen
worden geverifieerd door beproeving.
NEN-EN-IEC 61439-1
Laagspanningsschakel-en-verdeelinrichtingen
EMC conform
Te stellen eisen.
• De inwendige installatie en bedrading zijn uitgevoerd volgens de aanwijzingen
van de fabrikant van de componenten.
9/90
11. 19
NEN-EN-IEC 61439-1
Laagspanningsschakel-en-verdeelinrichtingen
EMC conform
Aan de beproeving te stellen eisen.
Black-Box
20
NEN-EN-IEC 61439-1
Laagspanningsschakel-en-verdeelinrichtingen
EMC conform
Voeding 230 VAC;50 HzMeet & Regel 4-20 mA
Data communicatie Profinet
Besturingskast
Aan de beproeving te stellen eisen.
10/90
12. 21
A. ESD
B. E-velden
C. Burst/EFT
D. Surge
E. Geleidende HF
F. H-velden
G. Dips/onderbreking
H. Harmonischen
Beproevingen
NEN-EN-IEC 61439-1
Laagspanningsschakel-en-verdeelinrichtingen
EMC conform
Immuniteitseisen Industrie
A
B
C
D
E
F
G
H
22
NEN-EN-IEC 61439-1
Laagspanningsschakel-en-verdeelinrichtingen
EMC conform
Immuniteitscriteria
11/90
14. 25
Emissie eisen Industrie
Aansluiting Frequntierange Limiet Afstand
Behuizing 30-230 MHz 40 dB (mV/m) 10 m
Behuizing 230-1000MHz 47 dB (mV/m) 10 m
Behuizing 1GHz-3GHz 76 dB (mV/m) 3 m
Behuizing 3GHz-6GHz 80 dB (mV/m) 3 m
Voeding 0,15MHz-0,5MHz 79 dB (mV) -
Voeding 0,5MHz-30MHz 73 dB (mV) -
Signaalkabel 0,15MHz-0,5MHz 97-87 dB (mV/m) -
Signaalkabel 0,15MHz-0,5MHz 53-43 dB (mV/m) -
Signaalkabel 0,5MHz-30MHz 87 dB (mV/m) -
Signaalkabel 0,5MHz-30MHz 43 dB (mV/m) -
NEN-EN-IEC 61439-1
Laagspanningsschakel-en-verdeelinrichtingen
EMC conform
OATS Open Area Test Site
IEC 61000-6-4
26
A. ESD
B. E-velden
C. Burst/EFT
D. Surge
E. RF geleiding
F. H-velden
G. Dips/onderbreking
H. Harmonischen
Beproevingen
NEN-EN-IEC 61439-1
Laagspanningsschakel-en-verdeelinrichtingen
EMC conform
Immuniteitseisen Industrie
A
B
C
D
E
F
G
H
13/90
15. 50 Hz 2kHz 150 kHz 30MHz 6GHz0 Hz
StralendGeleidend
ElektroMagnetische Compatibiliteit
Harmonischen
Burst/EFT
Surge
RF geleiding
EM velden
E-velden
H-velden
27
EMC
Conducted
(Bekabeling)
EMC
Radiated
(Behuizing)
NEN-EN-IEC 61439-1
Laagspanningsschakel-en-verdeelinrichtingen
EMC conform
EMC frequentie spectrum
Dips
Onderbrekingen
Skin-effect:
Power Quality
Impedantie:
28
Indien een SCHAKELINRICHTING die specifiek bestemd is voor
toepassing in omgeving A, gaat worden toegepast in omgeving B,
moet de volgende waarschuwing in de bedieningsvoorschriften zijn
opgenomen.
NEN-EN-IEC 61439-1
Laagspanningsschakel-en-verdeelinrichtingen
EMC conform
14/90
16. NEN-EN-IEC 61439-1
POWER QUALITY
Jentje Bootsma
2
NEN-EN-IEC 61439-1
Power Quality
Beproevingen
Dips/Onderbreking
IEC 61000-4-11
Industriële eisen Industrie
Gevoeligheid voor
spanningsverlaging en
onderbrekingen
A. ESD
B. E-velden
C. Burst/EFT
D. Surge
E. RF geleiding
F. H-velden
G. Dips/onderbreking
H. Harmonischen
A
B
C
D
E
F
G
H
15/90
17. 3
NEN-EN-IEC 61439-1
Power Quality
Dips/Onderbrekingen
Industriële eisen Industrie
Normaal bedrijf
10 ms 1 min
1%
90%
100%
110%
OnderspanningSpanningsdip
Korte onderbreking
NEN-EN 50160
3 min
Lange onderbreking
Overspanning
Definitie
Geen vastgestelde eisen
NEN-EN-IEC 61439-1
Power Quality
Dips/Onderbrekingen
16/90
18. Fenomenen:
6
Spanningsdips/korte onderbrekingen
• Kortsluitingen in het net
• Schakelingen in het net
Aard & Oorsprong
Gevolgen
• Uitvallen van installaties
• Flikkering van verlichting
NEN-EN-IEC 61439-1
Power Quality
Dips/Onderbrekingen
7
Dips/Onderbrekingen IEC 61000-4-11
Immuniteitsdiagram
Quint voeding
NEN-EN-IEC 61439-1
Power Quality
Dips/Onderbrekingen
Industriële eis IEC 61000-6-2
17/90
19. 1%
90%
100%
110%
Immuniteit
80%
70%
IEC 61000-4-11
Immuniteitsdiagram
apparaat
20 ms 200 ms 250 ms
40%
NEN-EN-IEC 61439-1
Power Quality
Dips/Onderbrekingen
Industriële eis IEC 61000-6-2
Uitval
9
Proces immuniteit tijd
t1 begin dip
Δt spanningsuitval overbrugging
t2 Procesparameter kan niet
worden gehandhaafd
PIT= t2-t1
Proces immuniteit tijd
NEN-EN-IEC 61439-1
Power Quality
Dips/Onderbrekingen
18/90
20. 1,0 A
3,0 A
0,4A
AC- UPS
DC- UPS
Process immunity time (PIT)
1,1 A
PITac= t2-t1
PIT= 4 min.
PITdc= t2-t1
PIT= 6 min.
NEN-EN-IEC 61439-1
Power Quality
Dips/Onderbrekingen
Maatregelen
Un-interruptable power supply (UPS)
QUINT UPS-IQ
UPS-DC
NEN-EN-IEC 61439-1
Power Quality
Dips/Onderbrekingen
Process immunity time (PIT)
Maatregelen
Un-interruptable power supply (UPS)
19/90
21. UPS-AC
UPS-CP
NEN-EN-IEC 61439-1
Power Quality
Dips/Onderbrekingen
=/
Process immunity time (PIT)
Maatregelen
Un-interruptable power supply (UPS)
Reference UPS-CP-
1kVA/240AC
UPS-CP-
2kVA/240AC
UPS-CP-
3kVA/240AC
UPS-CP-
4,5kVA/240AC
UPS-CP-
6kVA/240AC
Apparent power 1000 VA 2000 VA 3000 VA 4500 VA 6000 VA
Active power 800 W 1600 W 2400 W 3250 W 4200 W
Backup time (100% load) > 6 min. > 6 min. > 5 min. > 10 min. > 8 min.
classification VFI-SS-111 acc. to IEC62040-3 (Online / Double conversion)
Input 160…288 V AC 160…280 V AC
Output 200/ 208 / 220 / 230 / 240 V AC ± <1 % 200/208/220/230/240 V AC ± <2 %
Frequency 50 Hz ± 0,1 % (60 Hz) 50 Hz ± 0,2 % ( 60 Hz)
Harmonic distortion < 3% THD (linear load)
Crest factor 3:1
Transfer time 0 ms
Battery type Sealed, non-spillage, maintenance-free, lead acid
Maatregelen
Un-interruptable power supply (UPS)
NEN-EN-IEC 61439-1
Power Quality
Dips/Onderbrekingen
UPS-AC
20/90
22. 18
Beproevingen
NEN-EN-IEC 61439-1
Power Quality
IEC 61000-4-13
Industriële eisen Industrie
Gevoeligheid voor
spanningsvervorming
A. ESD
B. E-velden
C. Burst/EFT
D. Surge
E. RF geleiding
F. H-velden
G. Dips/onderbreking
H. Harmonischen
A
B
C
D
E
F
G
H
19
NEN-EN-IEC 61439-1
Power Quality
Industriële eisen Industrie
Gevoeligheid voor
spanningsvervorming
21/90
23. 20
NEN-EN-IEC 61439-1
Power Quality
Oude norm
NEN-EN-IEC 60439-1
Harmonischen
Industriële eisen Industrie
5%
50 Hz 2kHz 150 kHz 30MHz 6GHz0 Hz
StralendGeleidend
ElektroMagnetische Compatibiliteit
Harmonischen
Burst/EFT
Surge
RF geleiding
EM velden
E-velden
H-velden
21
EMC
Conducted
EMC
Radiated
Dips
Onderbrekingen
Power Quality
NEN-EN-IEC 61439-1
Power Quality
Harmonischen
22/90
24. HV OV
PCC
IPC1
Netbeheerder Installateur Paneelbouwer
Netcode NEN-EN-IEC 61000-2-4 NEN-EN-IEC 61000 reeksNEN-EN 50160
IPC4
IPC3
IPC2
IPC
Inplant point of coupling
Overdrachtspunt
PCC
Point of common coupling
Overdrachtspunt
22
NEN-EN-IEC 61439-1
Power Quality
Harmonischen
Elektromagnetische omgevingsklassen
Klasse 1: Residentieel
• Kantoor
• School
• Openbaar gebouw
Klasse 2: Industrieel
• PLC
• IPC
• M&R apparatuur
Klasse 3: Zwaar industrieel
• Frequentie omvormers
• Vermogensschakelaars
• Transformator station
NEN-EN-IEC 61000-2-4
23
NEN-EN-IEC 61439-1
Power Quality
Harmonischen
23/90
25. Industrie IEC 61000-2-4
24
Aanbeveling:
Afhankelijk van de betreffende klasse
Klasse 2 Besturing
Klasse 3 Motorregeling
3
2
NEN-EN-IEC 61439-1
Power Quality
Harmonischen
25
• Veroorzaakt door niet-lineaire
belastingen
• Injecteren van stromen met hogere
frequentie
Aard & Oorsprong
Gevolgen
• Gaan zich super poneren op de grondgolf
• Via netimpedantie ontstaan spanningsharmonischen
• Overbelasting van installatiedelen
NEN-EN-IEC 61439-1
Power Quality
Harmonischen
24/90
26. • Total Harmonic Distortion (THD)
• Crest Factor (CF)
• K factor
• Flicker (Pst)
• Effectieve waarde (RMS)
• Power Factor (PF)
• Displacement Power Factor (DPF)
Nieuwe Parameters
Interactie tussen spanning en stroom
26
Vastgelegd eisen/aanbevelingen
NEN-EN-IEC 61439-1
Power Quality
Harmonischen
Led lamp
M.b.v. fouriertransformatie beschrijven als som van sinusoïden
met frequentie gelijk of veelvoud van de grondfrequentie:
f(t)=a0/ 2+∑{ah cos(2pfht)+bh sin(2pfht)}
∞
h=1
Harmonischen:
Periodiek signaal
I
~
Eenfase gelijkrichting
Periodiek signaal
31
NEN-EN-IEC 61439-1
Power Quality
Harmonischen
25/90
29. Power Quality Analysers
Opdeling in klassen (IEC 61000-4-30):
Klasse A (Advanced)
• reproduceerbare metingen met hoge nauwkeurigheid
• b.v. compliance testen volgens norm
• metingen met contractuele of juridische
gevolgen
Klasse S (Surveys)
• zelfde meetintervallen als A, met kleinere
nauwkeurigheid
• b.v. statische of trouble-shooting metingen
37
Meten niet lineaire parameters
NEN-EN-IEC 61439-1
Power Quality
Harmonischen
IL1
IL2 IL3
IL1
IL2
IL3
I1H3
I2H3
I3H3
Sommatie van de stroom in de nul
Derde Harmonische in fase 38
Niet lineaire belasting
NEN-EN-IEC 61439-1
Power Quality
Harmonischen
28/90
41. Un-interruptable power supply (UPS)
66
~
UPS
1 3 5 7 9 11 13 15
100
50
0
1 3 5 7 9 11 13 15
100
50
0
Actieve filtering
Maatregelen
NEN-EN-IEC 61439-1
Power Quality
Harmonischen
IPC 1
Netconfiguratie
UPS
1
2
RMCC
RIO
PCC
5 ohm
5 ohm
L
M
H
S
MCC
d
IPC 67
V1 V2
M1
M2
IPC 2
Point of Common Coupling (PCC)
Inplant of Coupling (IPC)
Trafo
NEN-EN-IEC 61439-1
Power Quality
Harmonischen
40/90
42. 68
Geïntegreerde PQ meting
Power Quality inzichtelijk maken,
NEN-EN-IEC 61439-1
Power Quality
Harmonischen
Samenvatting
Alle niet-lineaire verbruikers gedragen zich als harmonische stroombron
Harmonischen zijn gehele veelvouden van de basisfrequentie
Algemeen gekarakteriseerd door THD
Harmonische worden onderverdeeld door hun rang
Stroomharmonischen vloeien door netimpedantie, waardoor
spanningsharmonische ontstaan
Spanningsharmonischen genereren stroomharmonischen in lineair
belastingen
Harmonische vervuiling neemt steeds meer toe
Compatibiliteitsniveaus vaststellen
69
NEN-EN-IEC 61439-1
Power Quality
Power Quality
Moderne kijk op spanning en stroom
• 14 oktober Assen
• 5 november Waalre
• 1 december Reeuwijk
• 10 december Zevenaar
41/90
43. 1
EMC Workshop
Jentje Bootsma
2
A. ESD
B. E-velden
C. Burst/EFT
D. Surge
E. RF geleiding
F. H-velden
G. Dips/onderbreking
H. Harmonischen
Beproevingen
Immuniteitseisen Industrie
A
B
C
D
E
F
G
H
NEN-EN-IEC 61439-1
EMC Conducted
IEC 61000-4-4
42/90
50. 8
Aardingssysteem
Standaard EMC-regels IEC 61000-5-2
Kabelgoot
Besturingspaneel
Voedingspaneel
• Aardelektrode
• Aardringleiding
• Hoofdaardrail
• Potentiaalvereffeningsrail
• EMC aarding
Klemmenkast
Apparaat
15
M&Rkabels
NEN-EN-IEC 61439-1
EMC Conducted
Standaard EMC-regels IEC 61000-5-2
NEN-EN-IEC 61439-1
EMC Conducted
• De inwendige installatie en bedrading zijn uitgevoerd volgens de
aanwijzingen van de fabrikant van de componenten.
49/90
51. 9
Burst
NEN-EN-IEC 61439-1
EMC Conducted
EMC Normen: Regelbare elektrische aandrijfsystemen
19
EMC Normen: Regelbare elektrische aandrijfsystemen
EN 61800-3: Algemeen
Documentatie voor de gebruiker
• max. en min. impedantie voedingssysteem
• toepassen van afgeschermde of speciaal kabel
• eisen kabelscherm aansluiting
• max. toegestane kabellengte
• kabelscheiding
• gebruik van externe apparaten (b.v. filters)
• juiste verbinding met aarde
NEN-EN-IEC 61439-1
EMC Conducted
50/90
52. 10
20
EMC Normen: Regelbare elektrische aandrijfsystemen
EN 61800-3: Emissie
NEN-EN-IEC 61439-1
EMC Conducted
Power interface
Motorkabel
24
EN 61800-3: Emissie
hoogfrequent
Frequentieregelaar
NEN-EN-IEC 61439-1
EMC Conducted
51/90
53. 11
• Leidingen afschermen of ferrietkernen
• “Aarding” geschikt voor HF
• “Aard” afscherming aan beide zijden
• Ongelakte montageplaat van de schakelkast
25
EN 61800-3: Emissie
hoogfrequent
Frequentieregelaar
NEN-EN-IEC 61439-1
EMC Conducted
U inverter
hoogfrequent
lekstroom
I = C. D U/ D t
Motorcircuit
26
EN 61800-3: Emissie
hoogfrequent
NEN-EN-IEC 61439-1
EMC Conducted
52/90
63. Themadag NEN-EN-IEC 61439
Bliksem en overspanning
René Bruins
Waarom bliksem en overspanningsbeveiliging ?
2
Algemene verzekeraar
Technische verzekeraar
62/90
64. 3
€ €
?
Hoe groot is het risico ?
2,2-2,4
2,4-2,6
2,6-2,8
2,8-3,0
3,0-3,2
3,2-3,4
bron: KNMI
In Nederland gemiddeld
200.000 inslagen per jaar
(hoogst geregistreerde aantal 450.000)
Aantal inslagen per
jaar/per km2 2,2 – 3,4
4
Hoe vaak komt het voor?
Extreme dagen,
met op 25 mei 2009
68710
ontladingen op 1 dag
63/90
65. 5
Programma
Verschillende (bliksem) normen
Wat is een overspanning
Zoneconcept
Overspanningsbeveiliging
Installatie aspecten
NEN-EN-IEC 61439 (inhoud)
6
• (H5) Technische kenmerken van interfaces
• Deze kenmerken moeten compatibel zijn met
de toegekende grootheden van de stroom-
ketens waarmee hij is verbonden
• Beproeving op EMC – immuniteit (Tabel J.1)
• De stoot-houdspanning van de apparatuur
moet groter of gelijk aan de te verwachten
transiënte overspanning zijn
• De waarde van deze stoot-houdspanning
wordt gegeven in tabel G.1
64/90
66. Noodzakelijke stoot-houdspanning
volgens table G.1 (afkomstig uit de IEC 60364-4-44)
7
Wat is (transiënte) overspanning ?
U
[V]
t
[ms]
0
Uc
Up
Transient
Over
Voltage
Time < 1msec
8
UN 400 VUc 350 V
Up 1500 V
UN 230 V
Nominal
Voltage
Time
UN
8
8/20
65/90
67. Samenhang diverse normen
9
Spannings- en elektromagnetische verstoringen in
laagspannings installaties
Overspanningen veroorzaakt door blikseminslag in
de buurt van of op binnenkomende
voedingskabels, en schakelhandelingen
Directe blikseminslag op het object
Algemeen
In NEN 1010:2015 meer aandacht voor nieuwe technologieën en onderwerpen in de
elektrotechniek.
Deze kenmerken zich vooral door het toenemende gebruik van elektronica en het toenemende
gebruik van elektrische energie.
In NEN 1010:2015 wordt rekening gehouden met de effecten hiervan op de elektrische
installaties binnen het toepassingsgebied van deze norm. Voorbeelden hiervan zijn:
— toenemende hogere harmonische spanningen en stromen;
— toenemende gevoeligheid van materieel (elektronica) voor overspanningen;
— toenemend gebruik van zonnepanelen als (parallelle) energiebron;
— toenemend gebruik van elektrische voertuigen
Nieuwe NEN 1010:2015
10
66/90
68. Deel 4-44-443 Beveiliging tegen overspanningen van atmosferische
oorsprong of als gevolg van schakelhandelingen
Er moet zijn voorzien in beveiliging tegen overspanning indien:
a) gevolgen gerelateerd zijn aan menselijk leven, bijvoorbeeld
veiligheidsdiensten, medisch materieel in ziekenhuizen;
b) gevolgen gerelateerd zijn aan publieke dienstverlening, bijvoorbeeld
uitvallen van publieke diensten, computercentra, museums;
c) gevolgen zijn voor commerciële of industriële activiteiten, bijvoorbeeld
hotels, banken, industrieën, commerciële markten, boerderijen;
Nieuwe NEN 1010:2015
11
Het beveiligen van elektrische en elektronische systemen.
SPD = (coördinated) surge protective device
12
LPZ 0 risico op directe bliksem inslag
LPZ 1 bliksemdeelstromen
LPZ 2 transiënten met laag-energieniveau
Interne beveiliging – zoneconcept volgens IEC 62305
Buiten
Binnen
67/90
69. hoofdverdeling
ZONE 1
onderverdeling
ZONE 2
ZONE 0 buiten
eindapparaat
ZONE 3
Overspanningsbeveiligingszones
Netbeveiliging
13
4 kV
2,5 kV
1,5 kV
A
B
S2 S3
S1
A
B
S2 S3
S1
A
B
S2 S3
S1
Overspanningsbeveiliging SPD
Principe
14
68/90
70. IEC 61643-11
Classificatie
15
T1
T2
T3
Impuls vormen volgens IEC 61643-11
10/350 µs (Lightning) gebruikt voor testen Typ 1
8/20 µs (Surge) gebruikt voor testen Typ 2
8
10 20
t
µs
i
î
1.0
0.5
0.0
0 100 200 300 350
video
16
69/90
71. Beveiligingselementen
Netbeveiliging (T1+T2/B+C/Klasse 1+2)
- Umax. :
- Ubev. :
- Iafl. :
- Max. :
350 V AC
1,5 kV
100 kA (10/350 µs)
315 A gG
Specificaties:
Toepassing:
Netbeveiliging bij directe
en indirecte blikseminslag
in hoofdverdeling
FLASHTRAB
FLT-SEC-…
17
Video
Beveiligingselementen
Netbeveiliging (T2/C/Klasse 2)
- Unom. :
- Ubev. :
- Iafl. :
- Max. :
350 V AC
1,4 kV
40 kA (8/20 µs)
315 A gG
Specificaties:
Toepassing:
Netbeveiliging bij
indirecte blikseminslag
in hoofd / onderverdeling
VALVETRAB
VAL-SEC…
18
70/90
72. Beveiligingselementen
Netbeveiliging (T3/D/Klasse 3)
MAINTRAB
MAINS-PLUGTRAB
- Unom.
- Inom. :
- Ubev. :
- Ubev. :
- Iafl. :
230 V AC
26A
1,50 kV (Ucm)
1,35 kV (Udm)
3 kA (8/20 µs)
Specificaties:
Toepassing:
Net-apparaatbeveiliging
bij indirecte blikseminslag
19
Installatie aspecten
Installatie/
apparatuur
F1
N
L1
F2
SPD’s
Type 1 + 2
PE
In
juiste zekering /
geen zekering
Umax. voor installatie (apparatuur)
maximale
leidinglengte
20
71/90
73. Leidinglengte !!
Installatie aspecten
21
1 m ~ 1 µH ~ 1kV (ekstra)
Potentiaal-
vereffeningsrail
Lengte van de aansluitleidingen
0,5 m
0,5 m
L
SPD
Parallelle aansluiting
Potentiaal-
vereffeningsrail
PE-rail
L
SPD
V-vormige (serie) aansluiting
22
72/90
75. 1
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
Rittal – The System.
Faster – better – everywhere.
2
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
Agenda
• ESD
• EMC
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
74/90
76. 3
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
ESD; Electro Static Discharge
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
Mens en “object”
5
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
ESD; Electro Static Discharge
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
Opladen komt door:
wrijving, tribo-elektrisch effect : hoe verder de materialen in de reeks uit elkaar liggen hoe
groter de ladingsoverdracht
Ladingen die zich van elkaar verwijderen : vergelijkbaar met de condensatorwerking van een
plaatcondensator.
Piezo-elektrische effect : door mechanisch stress aanbrengen bouwt lading op
Pyro-elektrisch effect: door verhitting bouwt lading op
75/90
77. 6
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
NEN-EN-IEC 61439-1:2011
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
ESD
8
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
NEN-EN-IEC 61439-1:2011
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
Elektromagnetische compatibiliteit (EMC) -
Deel 4-2: Beproevingen en meettechnieken -
76/90
78. 9
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
NEN-EN-IEC 61439-1:2011
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
Oplossingen
- afvoeren lading naar aarde
- Ander materiaal dan kunststof
- Voorkomen dat de lading via het object ontlaad
10
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
Agenda
• ESD
• EMC
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
77/90
79. 11
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
• Invloeden op het goed functioneren:
• - Externe invloeden
Waarom elektrische toestellen in een kast?
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
12
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
• Invloeden op het goed functioneren:
- Interne invloeden
Waarom elektrische toestellen in een kast?
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
78/90
80. 13
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
Elektromagnetische stoorbronnen
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
14
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
Elektromagnetische stoorbronnen
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
Dit ongewenste signaal verspreidt zich
- door geleiding in kabels
- straling door de lucht.
Ongewilde elektromagnetische storing is simpelweg een
ongewenst elektrisch signaal bovenop een
gewenst elektrisch signaal.
79/90
81. 15
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
Elektromagnetische stoorbronnen
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
Standaard metalen behuizingen bieden elektrische
apparaten een verregaande bescherming tegen
elektromagnetische storingsvelden.
16
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
Ideaalbeeld, de EMC-kast
.
EMC-kast
signaalkabel
netfilter
aardverbinding
voeding
zone 3/4 zone 3/2
EMC-wartel
apparaat
EM-veld
EMC-dichting
zone 3/4
EM-veld
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
EMC-dichting
80/90
82. 17
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
NEN-EN-IEC 61439-1:2011
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
Industrieel
21
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
Opbouw besturingspaneel - EMC afscherming
(kast in een kast H-veld)
EMC
zones conform IEC 61000-2-5:
zone 5, speciaal
zone 4, zwaar industrieel
zone 3, industrieel
zone 2, residentieel
zone 1, zeer gevoelig EMC
3
2
4
3
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
81/90
83. 23
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
Opbouw besturingspaneel –
EMC afscherming
Scheidingspanelen
zones conform IEC 61000-2-5:
zone 5, speciaal
zone 4, zwaar industrieel
zone 3, industrieel
zone 2, residentieel
zone 1, zeer gevoelig
zone 4, zwaar industrieel zone 3, industrieel
20 dB
20 dB
Theo Gerritzen / Product Manager
Kastsystemen / voorjaar 2014
24
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
Elektromagnetische afscherming
De demping is afhankelijk van:
• Materiaal:
plaatstaal, aluminium,
kunststof
• Frequentie:
150 KHz t/m 1 GHz
• Veldsoort:
magnetisch, elektrisch
• Geometriemateriaal:
afmeting van de kast)
Demping
plaatstaal
reflectie
100 KHz
volg-reflectie
veld
absorptie
tot circa
100 KHz
veld
zone 4, zwaar industrieel zone 3, industrieel
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
82/90
85. 27
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
Kabelinvoer TS8/AE
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
EMC invoer onderzijde EMC invoer bovenzijde
speciaal
Invoer met EMC kabelwartels
Standaard invoer onderzijde Standaard invoer bovenzijde Invoer met kabelwartels
28
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
Van EM-veld naar stroom/spanning
In de praktijk is de bekabeling
als een antenne voor storingen
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
84/90
86. 29
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
EMC-aardingsconcept besturingskast
(technical report IEC 61 000-5-2)
Het integreren met behulp van aardverbindingen voor frequenties
boven 10 KHz!!!
Nominale bedrijfsstroom
tot 20 A
van 20 t/m 25 A …………..
van 25 t/m 32 A …………..
van 32 t/m 63 A …………..
vanaf 63 A ………………...
Aarddraad of EMC-aardlitze
Vereffeningsleiding mm2
doorsnede van de fasegeleider
2,5
4
6
10 (tabel 4A EN 61439-1)
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
Skin effect
30
KASTSYSTEMEN STROOMVERDELING KLIMATISERING IT-INFRASTRUCTUUR SOFTWARE & SERVICE
EMC-kabelinvoer 360° contactering
(Volgens technicaI report IEC 61 000-5-2)
Theo Gerritzen / Product Manager
Kastsystemen / EMC-EN 61439
85/90