Chandresh Gupta is seeking assignments as a Manager of Piping Design with over 7 years of experience in equipment and piping layout for engineering, procurement, and construction projects. He has extensive experience in piping design, material specification preparation, stress analysis, and supporting project management. His background includes roles at Tata Steel and Mecon Limited where he was responsible for piping engineering, layout, sizing, material selection, and reviewing vendor documentation to ensure design compliance. He has skills in AutoCAD, CAESAR II, ERP, MS Project and knowledge of international piping standards.

1. CHANDRESH GUPTA
Manager – Piping Design,
Tata Steel – Kolkata
E-mail: chandresh.g@gmail.com; Phone: +91-9038001445
Seeking assignments in Piping Layout & Material with a high
growth oriented organization of repute
Key SkillKey Skill
 Good experience (7+ years) in Equipment & Piping layout for EPC Projects.
 Design calculation of pipe wall thickness, RF pad, Miter bend, Steam out condition.
 Piping layout arrangement for process unit (Water treatment plant piping, vessel piping, Pump piping, tank piping)
 Knowledge of materials (Carbon steel. Stainless steel, alloy steel and LTCS) used in process piping.
 Preparation of Piping material specification and valve material specification
 Preparation of Technical Specification for various packages.
 Receive, review and answer technical clarifications at tendering stage.
 Study and analyze bids in technical aspects, obtain clarifications and optimize all factors to establish a recommendation for
the contracts.
 Preparation of techno commercial comparative and ratings among the vendors and coordinating the same with commercial
department for order placement.
 Complete design of piping general arrangement layout, Pipe stress analysis, piping isometrics, supports details, plot plans,
equipment layout.
 Required calculations for Pipe wall thickness, maximum allowable operating pressure (MAOP) and test pressure.
 Preparing MTO requirements, pump and valve data sheets, scope of work, pipeline routing, and various piping calculations
used for process piping and pipe lines.
 Preparing and checking of equipment orientation drawings for rotary and static equipments, considering equipments spacing,
accessibility, and operation & maintenance requirements.
 Reviewing vendor drawings for various Engineering packages.
 Experienced in using programs and software including AUTOCAD, CAESAR-II, ERP, MS-PROJECT.
 Working knowledge of National and International standards and codes like ASME, API, BS, ASTM, MSS-SP and IS.
 Review all vendor documentations to assure the compliance with the design and technical requirements.
 Support to project management/procurement/construction team.
 Involved in Inter departmental coordination & query resolution.
PPROFESSIONALROFESSIONAL EEXPERIENCEXPERIENCE
TATA STEEL – Design Cell since July 2012
Designation :- Manager – Piping Design
Project Specific Experience
TATA STEEL, KPO:- Design and Detail Engineering of Piping System for Blast Furnace.

2. Key Responsibilities
 Piping engineering of PA, service& process water, LP steam, Nitrogen, Compressed air, Blast Furnace and Coke oven Gas, Soft
water, Oxygen and Hydraulics piping.
 Preparation of route layout of Pipelines, taking clearance from other section.
 Pipe line sizing, pipe wall thickness calculation for interplant pipelines.
 Preparation of General Arrangement Layout defining location for pipe Support (Anchor and sliding), vent, drain, U-loop,
Expansion bellow, orifice plate, U-seal, isolation valve, control valve.
 Modification in the Layout based on the result obtained after doing stress analysis to pass the system layout.
 Checking P&ID, General Arrangement Layout, Supports Details, MTO, Equipment’s location plans, Plot plans, Orientation
drawings.
 Procurement activity- Preparation of Specification, Negotiation and Order placement.
MECON LIMITED (A Govt. of India Enterprise)
June 2008 – june 2012
Designation :- Design Engineer
Project Specific Experience
NINL, DUBURI :- Complete Design and Detail Engineering for Piping Layout System
Key Responsibilities
 Isometric & GAD Checking Material as well as layout point of view
 Prepared piping material specification & valve material specification.
 Responsible for Pump House Piping, Yard Piping, In shop Piping.
 Prepared exchanger and vessel piping and set the platform elevation to access the vessel nozzle and instruments.
 Preparation of Equipment Layout of water and waste water, DMP, SWP etc.
 Pipe wall thickness calculation, pipe line sizing.
 Checking P&ID, General Arrangement Layout, Supports Details, MTO, Equipments location plans, Plot plans, Orientation
drawings.
 Review of piping material specifications, Pump and Valve data sheets.
 Review all Vendor documentations to assure the compliance with the design and technical requirements.
 Checking of Equipments orientation drawing for all types of equipments, considering equipments spacing, accessibility,
operation and maintenance requirements.
 Responsible for pipe rack study.
 Coordination with other disciplines to expedite the job.
 Continuously updated project drawings and documents to final As-built status.
EEDUCATION &DUCATION & PPROFESSIONALROFESSIONAL CCREDENTIALSREDENTIALS
PG Diploma in Project Planning and ManagementPG Diploma in Project Planning and Management
DG-tech HR, Kolkata - pursuing

3. PG Diploma in Piping Engineering - 2011
MIT, Pune - Attained First Division
BACHELOR OF TECHNOLOGY IN MECHANICAL ENGINEERING - 2008
NATIONAL INSTITUTE OF TECHNOLOGY, DURGAPUR – Attained First Division
COMPUTER SKILLS:COMPUTER SKILLS: AutoCAD, ERP, CAESAR - II, MS Project
AADDITIONALDDITIONAL IINFORMATIONNFORMATION
Date of Birth:Date of Birth: 225
th
Janauary’1986;; Passport Number:Passport Number: G4184986G4184986; Reference:Reference: Available on request