This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
Caterpillar cat 325 d l excavator (prefix nac) service repair manual (nac0000...fjsekdmmeed
This document provides repair instructions for a 325D L excavator transmission. It outlines 33 steps to disassemble and reassemble the transmission components. Key parts include the main housing, motor housing, bearings, seals, gears, carriers, plugs, and cover. The instructions emphasize cleanliness and applying anti-seize compound to parts during assembly. Precise measurements and shimming are required to set bearing preload.
Caterpillar cat w345 b series ii material handler (prefix anj) service repair...fjjsieskekfmmse
This document provides instructions for servicing the swing drive of a W345B Series II Material Handler. It lists the required tools and lubricants needed and provides detailed step-by-step instructions for disassembling and reassembling the swing drive. The instructions include cleaning and inspecting parts, applying lubricants, installing bearings and seals, torquing bolts, and reinstalling the completed swing drive. Special care must be taken to clean parts thoroughly and apply lubricants correctly during the reassembly process.
Caterpillar cat 365 b l mh excavator (prefix cty) service repair manual (cty0...fjjskekdmme
This document provides assembly instructions for a final drive in 29 steps. It begins by cleaning all parts and checking seals. It then details assembling bearings and gears in sequence using various tools. Precise measurements are taken to determine the correct shim thickness for proper bearing preload. Multiple planetary gear carrier assemblies are installed along with retaining rings and bolts. Proper torque specifications are listed throughout.
This document provides installation instructions for a final drive on an excavator. It lists the required tools and parts. The procedure involves positioning the final drive in the frame using lifting equipment, applying anti-seize compound to bolts, and torquing the bolts to specified values. The lifting equipment is then removed and the machine is lifted to remove installation stands.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
The document provides instructions for removing and installing a final drive assembly on an excavator. It lists the required tools and torque specifications for installation bolts. The removal procedure involves releasing hydraulic pressure, lifting the final drive assembly using link brackets and a vacuum cap, and removing installation bolts. The installation procedure specifies cleaning and applying anti-seize lubricant to bolts before tightening them to the specified torques while following an improved bolt tightening procedure.
Caterpillar cat m318 c wheeled excavator (prefix bcz) service repair manual (...udfjjdjkkmds
This document provides instructions for separating the upper frame and undercarriage frame on an M318C wheeled excavator. It lists the required tools which include electric hydraulic pumps, cylinders, stands, pins, tubes, collars, saddles, links and guide bolts. The procedure involves using the listed tools and hydraulic jacks to lift and support the frames while removing connecting components. Proper containment of fluids is noted as important during the separation process.
Caterpillar cat 323 d2 l excavator (prefix kbx) service repair manual (kbx000...fusjejkdkmse
This document provides assembly instructions for the final drive of a 323D2 L excavator. It outlines 35 steps to assemble the components, including installing bearings, seals, gears, carriers, plugs and other parts. Precise measurements and torque specifications are required. Cleanliness is critical throughout the process to prevent contamination.
Caterpillar cat 325 d l excavator (prefix nac) service repair manual (nac0000...fjsekdmmeed
This document provides repair instructions for a 325D L excavator transmission. It outlines 33 steps to disassemble and reassemble the transmission components. Key parts include the main housing, motor housing, bearings, seals, gears, carriers, plugs, and cover. The instructions emphasize cleanliness and applying anti-seize compound to parts during assembly. Precise measurements and shimming are required to set bearing preload.
Caterpillar cat w345 b series ii material handler (prefix anj) service repair...fjjsieskekfmmse
This document provides instructions for servicing the swing drive of a W345B Series II Material Handler. It lists the required tools and lubricants needed and provides detailed step-by-step instructions for disassembling and reassembling the swing drive. The instructions include cleaning and inspecting parts, applying lubricants, installing bearings and seals, torquing bolts, and reinstalling the completed swing drive. Special care must be taken to clean parts thoroughly and apply lubricants correctly during the reassembly process.
Caterpillar cat 365 b l mh excavator (prefix cty) service repair manual (cty0...fjjskekdmme
This document provides assembly instructions for a final drive in 29 steps. It begins by cleaning all parts and checking seals. It then details assembling bearings and gears in sequence using various tools. Precise measurements are taken to determine the correct shim thickness for proper bearing preload. Multiple planetary gear carrier assemblies are installed along with retaining rings and bolts. Proper torque specifications are listed throughout.
This document provides installation instructions for a final drive on an excavator. It lists the required tools and parts. The procedure involves positioning the final drive in the frame using lifting equipment, applying anti-seize compound to bolts, and torquing the bolts to specified values. The lifting equipment is then removed and the machine is lifted to remove installation stands.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
The document provides instructions for removing and installing a final drive assembly on an excavator. It lists the required tools and torque specifications for installation bolts. The removal procedure involves releasing hydraulic pressure, lifting the final drive assembly using link brackets and a vacuum cap, and removing installation bolts. The installation procedure specifies cleaning and applying anti-seize lubricant to bolts before tightening them to the specified torques while following an improved bolt tightening procedure.
Caterpillar cat m318 c wheeled excavator (prefix bcz) service repair manual (...udfjjdjkkmds
This document provides instructions for separating the upper frame and undercarriage frame on an M318C wheeled excavator. It lists the required tools which include electric hydraulic pumps, cylinders, stands, pins, tubes, collars, saddles, links and guide bolts. The procedure involves using the listed tools and hydraulic jacks to lift and support the frames while removing connecting components. Proper containment of fluids is noted as important during the separation process.
Caterpillar cat 323 d2 l excavator (prefix kbx) service repair manual (kbx000...fusjejkdkmse
This document provides assembly instructions for the final drive of a 323D2 L excavator. It outlines 35 steps to assemble the components, including installing bearings, seals, gears, carriers, plugs and other parts. Precise measurements and torque specifications are required. Cleanliness is critical throughout the process to prevent contamination.
Caterpillar cat w345 b series ii material handler (prefix anj) service repair...fioskdmmd
This document provides instructions for servicing the swing drive of a material handler. It lists the required tools and notes on cleanliness. The 40 step procedure describes how to disassemble, clean, replace seals and bearings, and reassemble the swing drive. Proper application of lubricants and locking compounds is emphasized throughout.
The document provides assembly and removal procedures for a 320D2 and 320D2 L excavator final drive:
- It outlines 38 steps for assembling the final drive, including installing bearings, seals, gears, carriers, covers, and attaching it to the frame.
- It also lists the required tools and torque specifications.
- The 4 step removal procedure involves releasing hydraulic pressure, lifting the final drive out of the frame, and detaching the track assembly. Cleanliness and proper torque are emphasized throughout.
The document provides assembly and removal procedures for a 320D2 and 320D2 L excavator final drive:
- It outlines 38 steps for assembling the final drive, including installing bearings, seals, gears, carriers, covers, and attaching it to the frame.
- It also lists the required tools and torque specifications.
- The 4 step removal procedure involves releasing hydraulic pressure, lifting the final drive out of the frame, and detaching the track assembly. Cleanliness and proper torque are emphasized throughout.
This document provides the assembly procedure for a final drive on excavator models 320D2 and 320D2 L. The 38 step procedure installs and secures over 30 individual parts in the proper order using various tools. Cleanliness is important during assembly and O-rings, seals, and gaskets should always be replaced. The procedure includes instructions for installing bearings, seals, gears, carriers, covers, and bolts while applying specified torque values.
Caterpillar cat 320 d2 l excavator (prefix sdz) service repair manual (sdz000...fdjsuekskefmm
The document provides instructions for removing and installing a final drive assembly on an excavator. It lists the required tools and torque specifications for installation bolts. The removal procedure involves releasing hydraulic pressure, lifting the final drive assembly using link brackets and a vacuum cap, and removing installation bolts. The installation procedure specifies cleaning and applying anti-seize lubricant to bolts before tightening them to the specified torques while following an improved bolt tightening procedure.
This document provides the assembly procedure for a final drive on excavator models 320D2 and 320D2 L. The 38 step procedure installs bearings, seals, gears, carriers, covers and other components into the main housing and motor housing using various tools. Precise measurements and torque specifications are required to properly preload bearings and install components. Cleanliness is critical throughout the assembly process.
Caterpillar cat 320 d2 l excavator (prefix sdz) service repair manual (sdz000...fjjskkdmnsme
This document provides the assembly procedure for a 320D2 and 320D2 L excavator final drive. It involves 38 steps including installing bearings, seals, gears, carriers, covers and other components. Proper cleaning, lubrication and torque specifications are noted. Required tools include a transmission repair stand, link brackets, seal installer, anti-seize lubricant and thread locking compounds.
Caterpillar cat 320 d2 l excavator (prefix sdz) service repair manual (sdz000...fujdfjjkskekme
The document provides instructions for removing and installing a final drive assembly on an excavator. It lists the required tools and torque specifications for installation bolts. The removal procedure involves releasing hydraulic pressure, lifting the final drive assembly using link brackets and a vacuum cap, and removing installation bolts. The installation procedure specifies cleaning and applying anti-seize lubricant to bolts before tightening them to the specified torques while following an improved bolt tightening procedure.
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...shudun96087
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...kesi7153062
The document provides installation instructions for assembling the swing drive of an excavator. It involves 30 steps including installing bearings and seals into the drive shaft assembly, installing gears and carriers, applying sealant and installing the ring gear and housing cover. Special tools and precautions are noted regarding cleanliness and bearing temperatures. Proper torque values and tightening procedures are specified for reinstalling the completed swing drive assembly into the excavator frame.
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...cnp692569
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the inner and outer dust seals from the swing gear and bearing.
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...f8uejkdkdmm3e
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...f89siekkmdmm2w
The document provides instructions for assembling and installing the swing drive of an excavator. It describes 30 steps for assembling the internal components of the swing drive, including installing bearings, gears, seals, and housing components. It then describes 6 steps for installing the entire assembled swing drive into the excavator frame, including attaching lifting brackets, applying sealant, tightening bolts to the specified torque, and filling it with oil. The overall process installs and secures the fully assembled swing drive subsystem into the excavator.
Kobelco sk500 lc 10 hydraulic excavator (na 2019) service repair manualfioskdmmd
This document is the shop manual for repairing and maintaining an excavator. It contains outlines and general precautions for repairs. The manual is divided into 7 chapters covering specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachments. Precautions are provided for preparing for disassembly work, safety during disassembly and assembly, hydraulic equipment, electrical equipment, hydraulic parts, welding repairs, and environmental issues. The copyright of the manual belongs to Kobelco Construction Machinery Co. and permission is required for copying or distributing the manual.
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and engine information for a SK500LC-10 hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installation of options. The document emphasizes safety precautions that should be taken when operating or servicing the excavator.
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and optional information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installing options. The document outlines general safety information and precautions that should be followed when operating or servicing the excavator.
Kobelco sk460 8 (hs engine) hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and optional information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installing options. The document outlines general safety information and precautions that should be followed when operating or servicing the excavator.
Kobelco sk350 lc 10 hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that contains specifications, maintenance, system, disassembly, and troubleshooting sections for a hydraulic excavator model. It provides safety information and precautions for operating and servicing the excavator. The manual instructs technicians to take proper safety measures like wearing protective equipment, relieving pressures, and using lifting devices when working on the excavator. It also warns against dangers like hot surfaces and moving parts that could cause injuries.
Kobelco sk350 lc 8 hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that provides specifications, maintenance, system, disassembly, and troubleshooting information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine procedures, and installing options. The document provides general safety information and precautions for operating and servicing the excavator.
More Related Content
Similar to Caterpillar cat w345 b series ii material handler (prefix cdy) service repair manual (cdy00001 and up)
Caterpillar cat w345 b series ii material handler (prefix anj) service repair...fioskdmmd
This document provides instructions for servicing the swing drive of a material handler. It lists the required tools and notes on cleanliness. The 40 step procedure describes how to disassemble, clean, replace seals and bearings, and reassemble the swing drive. Proper application of lubricants and locking compounds is emphasized throughout.
The document provides assembly and removal procedures for a 320D2 and 320D2 L excavator final drive:
- It outlines 38 steps for assembling the final drive, including installing bearings, seals, gears, carriers, covers, and attaching it to the frame.
- It also lists the required tools and torque specifications.
- The 4 step removal procedure involves releasing hydraulic pressure, lifting the final drive out of the frame, and detaching the track assembly. Cleanliness and proper torque are emphasized throughout.
The document provides assembly and removal procedures for a 320D2 and 320D2 L excavator final drive:
- It outlines 38 steps for assembling the final drive, including installing bearings, seals, gears, carriers, covers, and attaching it to the frame.
- It also lists the required tools and torque specifications.
- The 4 step removal procedure involves releasing hydraulic pressure, lifting the final drive out of the frame, and detaching the track assembly. Cleanliness and proper torque are emphasized throughout.
This document provides the assembly procedure for a final drive on excavator models 320D2 and 320D2 L. The 38 step procedure installs and secures over 30 individual parts in the proper order using various tools. Cleanliness is important during assembly and O-rings, seals, and gaskets should always be replaced. The procedure includes instructions for installing bearings, seals, gears, carriers, covers, and bolts while applying specified torque values.
Caterpillar cat 320 d2 l excavator (prefix sdz) service repair manual (sdz000...fdjsuekskefmm
The document provides instructions for removing and installing a final drive assembly on an excavator. It lists the required tools and torque specifications for installation bolts. The removal procedure involves releasing hydraulic pressure, lifting the final drive assembly using link brackets and a vacuum cap, and removing installation bolts. The installation procedure specifies cleaning and applying anti-seize lubricant to bolts before tightening them to the specified torques while following an improved bolt tightening procedure.
This document provides the assembly procedure for a final drive on excavator models 320D2 and 320D2 L. The 38 step procedure installs bearings, seals, gears, carriers, covers and other components into the main housing and motor housing using various tools. Precise measurements and torque specifications are required to properly preload bearings and install components. Cleanliness is critical throughout the assembly process.
Caterpillar cat 320 d2 l excavator (prefix sdz) service repair manual (sdz000...fjjskkdmnsme
This document provides the assembly procedure for a 320D2 and 320D2 L excavator final drive. It involves 38 steps including installing bearings, seals, gears, carriers, covers and other components. Proper cleaning, lubrication and torque specifications are noted. Required tools include a transmission repair stand, link brackets, seal installer, anti-seize lubricant and thread locking compounds.
Caterpillar cat 320 d2 l excavator (prefix sdz) service repair manual (sdz000...fujdfjjkskekme
The document provides instructions for removing and installing a final drive assembly on an excavator. It lists the required tools and torque specifications for installation bolts. The removal procedure involves releasing hydraulic pressure, lifting the final drive assembly using link brackets and a vacuum cap, and removing installation bolts. The installation procedure specifies cleaning and applying anti-seize lubricant to bolts before tightening them to the specified torques while following an improved bolt tightening procedure.
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...shudun96087
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...kesi7153062
The document provides installation instructions for assembling the swing drive of an excavator. It involves 30 steps including installing bearings and seals into the drive shaft assembly, installing gears and carriers, applying sealant and installing the ring gear and housing cover. Special tools and precautions are noted regarding cleanliness and bearing temperatures. Proper torque values and tightening procedures are specified for reinstalling the completed swing drive assembly into the excavator frame.
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...cnp692569
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the inner and outer dust seals from the swing gear and bearing.
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...f8uejkdkdmm3e
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...f89siekkmdmm2w
The document provides instructions for assembling and installing the swing drive of an excavator. It describes 30 steps for assembling the internal components of the swing drive, including installing bearings, gears, seals, and housing components. It then describes 6 steps for installing the entire assembled swing drive into the excavator frame, including attaching lifting brackets, applying sealant, tightening bolts to the specified torque, and filling it with oil. The overall process installs and secures the fully assembled swing drive subsystem into the excavator.
Similar to Caterpillar cat w345 b series ii material handler (prefix cdy) service repair manual (cdy00001 and up) (16)
Kobelco sk500 lc 10 hydraulic excavator (na 2019) service repair manualfioskdmmd
This document is the shop manual for repairing and maintaining an excavator. It contains outlines and general precautions for repairs. The manual is divided into 7 chapters covering specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachments. Precautions are provided for preparing for disassembly work, safety during disassembly and assembly, hydraulic equipment, electrical equipment, hydraulic parts, welding repairs, and environmental issues. The copyright of the manual belongs to Kobelco Construction Machinery Co. and permission is required for copying or distributing the manual.
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and engine information for a SK500LC-10 hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installation of options. The document emphasizes safety precautions that should be taken when operating or servicing the excavator.
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and optional information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installing options. The document outlines general safety information and precautions that should be followed when operating or servicing the excavator.
Kobelco sk460 8 (hs engine) hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and optional information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installing options. The document outlines general safety information and precautions that should be followed when operating or servicing the excavator.
Kobelco sk350 lc 10 hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that contains specifications, maintenance, system, disassembly, and troubleshooting sections for a hydraulic excavator model. It provides safety information and precautions for operating and servicing the excavator. The manual instructs technicians to take proper safety measures like wearing protective equipment, relieving pressures, and using lifting devices when working on the excavator. It also warns against dangers like hot surfaces and moving parts that could cause injuries.
Kobelco sk350 lc 8 hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that provides specifications, maintenance, system, disassembly, and troubleshooting information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine procedures, and installing options. The document provides general safety information and precautions for operating and servicing the excavator.
Kobelco sk330 10 hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that contains specifications, maintenance, system, disassembly, troubleshooting, and engine sections for hydraulic excavator models SK330-10 and SK350LC-10. It provides safety information and precautions for operating and servicing the excavators. The manual outlines general safety messages and contains warnings for working on pressurized systems, lifting heavy components, hot parts, and ensuring all guards are in place before starting work.
Kobelco sk330 8 hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that provides specifications, maintenance, system, disassembly, and troubleshooting information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine procedures, and installing options. The document provides general safety information and precautions for operating and servicing the excavator.
Kobelco sk260 lc 10 hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that contains specifications, maintenance, system, disassembly, and troubleshooting sections for a hydraulic excavator model. It provides safety information and precautions for operating, maintaining, and repairing the excavator. The manual instructs technicians to take proper safety measures like using protective equipment, relieving pressures, lowering attachments, and checking for hot or damaged parts before performing any work.
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and optional information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installing options. The document provides general safety information and precautions for operating and servicing the excavator.
Kobelco sk250 10 hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that contains specifications, maintenance, system, disassembly, and troubleshooting sections for a hydraulic excavator model. It provides safety information and precautions for operating and servicing the excavator. The manual instructs technicians to take proper safety measures like using protective equipment, relieving pressures, and blocking components before working on the excavator. It also warns against dangers like hot surfaces, lifting heavy parts incorrectly, and damaged wiring or hoses.
Kobelco sk250 8 (hs engine) hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and optional information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installing options. The document outlines general safety information and precautions that should be followed when operating or servicing the excavator.
Kobelco sk230 srlc 5e hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that provides specifications, maintenance, system, disassembly, and troubleshooting information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine procedures, and installing options. The document provides important safety information that should be read and understood before working on the excavator.
Kobelco sk230 srlc 5 hydraulic excavator service repair manualfioskdmmd
This document is the shop manual for a hydraulic excavator. It outlines general precautions for repairs, including preparing the machine, safety procedures, hydraulic system procedures, electrical work, and welding repairs. It notes that the copyright belongs to Kobelco Construction Machinery and outlines restrictions on copying or distributing the manual's contents. The manual is intended to provide repair, maintenance, and adjustment instructions for the excavator.
Kobelco sk230 srlc 3 hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that provides specifications, maintenance, system, disassembly, and troubleshooting information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine procedures, and installing options. Safety information is provided throughout, including warnings regarding proper operation, maintenance, lifting heavy components, hot surfaces, and pressurized fluids. Precautions are outlined for repair work.
Kobelco sk210 lc 10 (for north america) hydraulic excavator service repair ma...fioskdmmd
This document is the shop manual for a hydraulic excavator. It contains 7 chapters that provide information for maintenance, repair, troubleshooting and specifications for the excavator. The chapters cover topics like the hydraulic, electrical and component systems, disassembly/assembly instructions, engine information and optional attachment procedures. Safety precautions are provided for working on the equipment. The manual is copyrighted and any reproduction or distribution requires permission from the original manufacturer.
Kobelco sk140 srlc 7 hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and options information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine procedures, and installing options. The manual provides important safety information and precautions for operating and servicing the excavator.
Kobelco sk130 lc 11 hydraulic excavator service repair manualfioskdmmd
This document provides an outline and general precautions for repairing a hydraulic excavator shop manual. It discusses the copyright of the manual, safety precautions for disassembly and assembly, handling hydraulic and electrical equipment, welding repairs, and environmental issues. Measurement units used are also described. The manual is intended solely for repair and maintenance of machines sold by Kobelco and cannot be copied, distributed or used for other purposes without permission.
Kobelco sk85 msr 7 hydraulic excavator service repair manualfioskdmmd
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and engine information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installing options. The manual provides important safety information and precautions for operating and servicing the excavator.
Kobelco sk85 cs 7 hydraulic excavator service repair manualfioskdmmd
This document appears to be a shop manual that provides specifications, maintenance, system, disassembly, and troubleshooting information for a hydraulic excavator model. It contains various sections covering the specifications, maintenance, systems, disassembly process, engine, and installing optional components of the excavator. The document emphasizes safety precautions that should be followed when operating or servicing the excavator, such as wearing protective equipment, using proper lifting procedures for heavy components, and relieving pressure from hydraulic systems before disconnecting lines.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: W345B II WHEELED EXCAVATOR CDY
Configuration: W345B Series II Material Handlers CDY00001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
345B, 345B Series II and W345B Series II Excavators Machine Systems
Media Number -SENR1934-11 Publication Date -01/01/2012 Date Updated -12/01/2012
i02830548
Swing Drive - Assemble
SMCS - 5459-016
S/N - AGS1-UP
S/N - AKX1-UP
S/N - ALB1-UP
S/N - ALD1-UP
S/N - AMD1-UP
S/N - AMJ1-UP
S/N - AMN1-UP
S/N - ANJ1-UP
S/N - APB1-UP
S/N - AYR1-UP
S/N - CCC1-UP
S/N - CDY1-UP
S/N - DCW1-UP
S/N - DET1-UP
S/N - FEE1-UP
Assembly Procedure
1/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B 1P-2420 Transmission Repair Stand 1
C
5P-5197 Retaining ring pliers 1
1U-8759 Tip Set 1
D 1P-0510 Drive Group 1
E 1U-6396 O-Ring Assembly Compound 1
F 5P-3931 Anti-Seize Compound 1
G 5P-0960 Molybdenum Grease 1
H 9S-3263 Thread Lock Compound 1
J 1U-8846 Gasket Sealant 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use Tooling (E) during the assembly procedure.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Make sure that all parts of the swing drive are thoroughly clean and free of dirt and debris
prior to assembly.
2/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 1 g00725394
2. Apply Tooling (F) on the outside diameter of bearing (37) and the inside diameter of swing
drive housing (19) .
3. Lower the temperature of bearing (37) . Install bearing (37) in the swing drive housing.
Illustration 2 g00725388
4. Install O-ring seal (35) into bearing cage (31) .
5. Install the two lip seals (34) in bearing cage (31) .
6. Apply Tooling (G) on the lip of each seal.
3/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 3 g00725547
7. Carefully install cage (31) over pinion shaft (33) .
Illustration 4 g00725554
8. Heat bearing (39) to a temperature of 135 °C (275 °F) and install bearing (39) on the pinion
shaft (33) .
Illustration 5 g00725572
4/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. 9. Install spacer (38) on top of bearing (37) , as shown.
Note: Lip (e) for spacer (38) must face opposite bearing (37) , as shown.
Illustration 6 g00725575
10. Put swing drive housing (19) in the press.
11. Apply Tooling (F) on the outside diameter of bearing (39) and the inside diameter of the
swing drive housing.
12. Install pinion shaft (33) , bearing cage (31) , bearing assembly (39) , through spacer (38)
and bearing (37) .
Note: It may be necessary to reposition the press so that bearing assembly (39) is installed
evenly into the swing drive housing.
Note: Align bearing cage (31) with the swing drive housing during installation of the pinion
shaft. Temporarily install two bolts that will hold bearing cage (31) to the swing drive
housing.
Illustration 7 g00725595
5/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 13. Remove the swing drive from the press and place the swing drive sideways. The combined
weight of the swing drive housing, the pinion shaft, and the bearing cage is 152 kg (335 lb).
14. Remove the temporary bolts that are holding the bearing cage in position.
15. Apply Tooling (H) on the threads of bolts (32) that hold bearing cage (31) to swing drive
housing (19) .
16. Tighten bolts (32) to a torque of 100 ± 20 N·m (75 ± 15 lb ft).
Illustration 8 g00725607
17. Heat bearing cone (36) to a temperature of 135 °C (275 °F). Install bearing cone (36) on the
pinion shaft (33) .
Note: Make sure that the shaft is centered in the swing drive housing, before you install
bearing cone (36) .
Illustration 9 g00725270
18. Use Tooling (C) to install retaining ring (30) .
19. Assemble the carrier assembly (21) , as follows:
6/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 10 g00725260
a. Apply clean SAE 30W oil on bearing (26) and bearing (28) . Install bearings (26) and
(28) into planetary gear (27) .
b. Install thrust washer (25) on one side of planetary gear (27) .
c. Install thrust washer (29) on the opposite side of planetary gear (27) .
d. Use a deburring tool in order to remove the metal burr from the openings in the
carrier.
e. Install planetary gear (27) and the thrust washers in the carrier assembly (21) .
Illustration 11 g00725252
f. Install planetary shaft (24) through the gear assembly into the carrier assembly. Make
sure that the spring pin hole in the planetary shaft is in alignment with the spring pin
hole in the carrier.
7/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 12 g00703700
g. Drive spring pin (23) into shaft (24) . Orient the split in spring pin (23) vertically to
the carrier. Align the split in the spring pin to the top or to the bottom. Make a stake
mark on each side of the spring pin hole in the carrier. Each stake mark should be
approximately 2.25 ± 0.75 mm (0.09 ± 0.03 inch) from the outside diameter of the
spring pin hole.
h. Repeat Steps 19.a through 19.g in order to install the remaining planetary gears (27)
in the carrier.
Illustration 13 g00725203
20. Use two people and install carrier assembly (21) into the housing. The weight of carrier
assembly (21) is approximately 40 kg (88 lb).
8/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 14 g00725194
21. Install retaining ring (22) .
Illustration 15 g00725186
22. Install spacer (20) into carrier assembly (21) .
Illustration 16 g00725166
9/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 23. Make sure that the mating surfaces of the ring gear (18) and the swing drive housing (19)
are thoroughly clean.
24. Apply Tooling (J) to the face of swing drive housing (19) and the face of ring gear (18) .
25. Install Tooling (A) onto ring gear (18) . Weight of the ring gear is approximately 36 kg (80
lb).
26. Install ring gear (18) onto the swing drive housing (19) .
Illustration 17 g00725145
27. Install retaining ring (17) into the sun gear.
Illustration 18 g00724866
28. Install carrier (7) into the sun gear. Install retaining ring (15) into sun gear (16) .
29. Assemble carrier assembly (7) , as follows:
10/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 19 g00724862
a. Apply clean SAE 30W oil on bearing (13) . Install bearing (13) in planetary gear
(12) .
b. Install a thrust washer (11) on one side of planetary gear (12) .
c. Install a thrust washer (14) on the opposite side of planetary gear (12) .
d. Use a deburring tool in order to remove the metal burr from the openings in the
carrier.
e. Install planetary gear (12) and the thrust washers in the carrier assembly (7) .
Illustration 20 g00724860
f. Install planetary shaft (10) through the gear assembly into the carrier assembly. Make
sure that the spring pin hole in the planetary shaft is in alignment with the spring pin
hole in the carrier.
11/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 21 g00703700
g. Drive spring pin (9) into shaft (10) . Orient the split in spring pin (9) vertically to the
carrier. Align the split in the spring pin to the top or to the bottom. Make a stake mark
on each side of the spring pin hole in the carrier. Each stake mark should be
approximately 2.25 ± 0.75 mm (0.09 ± 0.03 inch) from the outside diameter of the
spring pin hole.
h. Repeat Steps 29.a through 29.g for the remaining gear assemblies.
Illustration 22 g00724856
30. Install carrier assembly (7) in the ring gear.
31. Install spacer (8) into carrier assembly (7) .
12/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 23 g00724854
32. Install sun gear (6) into carrier assembly (7) .
Illustration 24 g00724840
33. Make sure that the mating surfaces of the ring gear and cover (5) are thoroughly clean.
34. Apply Tooling (J) on the flange surface of the ring gear and cover (5) .
35. Fasten Tooling (A) and a suitable lifting device to cover (5) . Put the cover in the original
position on the ring gear. Make sure that the cover is seated properly.
13/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 25 g00724843
36. Apply Tooling (H) on the threads of bolts (4) .
37. Install the washers and bolts (4) that hold the cover, the ring gear, and the swing drive
housing together. Tighten bolts (4) to a torque of 270 ± 40 N·m (200 ± 30 lb ft).
38. Install fitting (3) into cover (5) .
Illustration 26 g00724832
39. Install oil level gauge (Dipstick) (1) , filler breather cap assembly and hose assembly (2) to
the swing drive.
40. If the drain valve was removed from the swing drive housing, reinstall the drain valve.
End By: Install the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 01:20:39 UTC+0800 2020
14/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: W345B II WHEELED EXCAVATOR CDY
Configuration: W345B Series II Material Handlers CDY00001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
345B, 345B Series II and W345B Series II Excavators Machine Systems
Media Number -SENR1934-11 Publication Date -01/01/2012 Date Updated -12/01/2012
i01450853
Swing Drive - Install
SMCS - 5459-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(A)
132-8223 110 volt Power Pack (1)
1
1U-6221 Torque Wrench 1
132-8143 36 mm Hex Link 1
(B) 138-7573 Link Bracket 4
( 1 )
132-8231 220 volt Power Pack is available.
1. The following installation procedure is identical for both swing drives.
2. Thoroughly clean the mating surfaces of the swing drive housing and the main frame.
3. Apply 5P-3931 Anti-Seize Compound on the locating pin in the main frame. Also, apply 5P
-3931 Anti-Seize Compound in the pin bore in the main frame.
4. Apply 1U-8846 Sealant on the mating surface of the main frame and the swing drive
housing.
1/3(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 1 g00635629
Note: During installation, the locating pin for the swing drive can come out of the swing
drive housing.
5. Fasten Tool (B) and a hoist to swing drive (3). The weight of the swing drive is 227 kg (500
lb). Place the swing drive in the swing drive's original position in the main frame. If the
locating pin comes out of the swing drive housing, the locating pin can be reinstalled with a
hammer after the swing drive is in place.
Illustration 2 g00635627
6. Apply 9S-3263 Thread Lock Compound on the threads of bolts (1). Install the bolts and the
washers that hold the swing drive in place. Tighten the bolts evenly with Tooling (A) to a
torque of 900 ± 100 N·m (665 ± 75 lb ft).
7. Install two corks (2) in the threaded holes in the swing drive housing.
8. After installation of the swing motor, fill the hydraulic oil tank and the swing drive with oil
to the proper level.
Reference: Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
Reference: Refer to Operation and Maintenance Manual, "Refill Capacities" for the correct
amount.
2/3(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Reference: Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level -
Check" for the correct filling procedures.
Reference: Refer to Operation and Maintenance Manual, "Swing Drive Oil Level - Check"
for the correct filling procedures.
End By: Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install" in
this manual.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 01:21:36 UTC+0800 2020
3/3(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: W345B II WHEELED EXCAVATOR CDY
Configuration: W345B Series II Material Handlers CDY00001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
345B, 345B Series II and W345B Series II Excavators Machine Systems
Media Number -SENR1934-11 Publication Date -01/01/2012 Date Updated -12/01/2012
i01187801
Swing Gear and Bearing - Remove
SMCS - 7063-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(A) 138-7574 Link Bracket 4
(B)
132-8223 115 volt Power Pack 1
132-8112 3/4 inch Drive Torque Wrench 1
9U-6529 24 mm Socket 1
Start By:
a. Remove the undercarriage frame assembly. Refer to Disassembly and Assembly, "Undercarriage
Frame - Remove" in this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 1. Remove all of the grease from the swing gear and bearing. Put the grease in a suitable container for
storage or disposal.
Illustration 1 g00520664
2. Put an alignment mark on swing gear and bearing (1) and the undercarriage frame assembly for
installation purposes.
3. Fasten Tooling (A) and a suitable lifting device to swing gear and bearing (1), as shown. Put a slight
lifting tension on the swing gear and bearing.
Illustration 2 g00520670
4. Use Tooling (B) to remove bolts (2) and the spacers that secure swing gear and bearing (1) to the
undercarriage frame assembly.
5. Carefully remove the swing gear and bearing from the undercarriage frame assembly. The weight of
the swing gear and bearing is 454 kg (1000 lb).
2/3(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 3 g00636223
6. Place tape over the sealing surfaces of the dust seals, the inner race and the outer race. This will
prevent cleaning solvent from entering the cross sections of the dust seals. Thoroughly clean the
swing gear and bearing.
7. Remove dust seals (3) and (4) from the outer race and the inner race of the swing gear and bearing.
8. Clean the sealing grooves of the inner race and outer race with fine grit sandpaper. Use a cleaning
solvent to clean the seal grooves. Make sure that the seal grooves are thoroughly clean and dry prior
to installing new dust seals.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 01:22:33 UTC+0800 2020
3/3(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: W345B II WHEELED EXCAVATOR CDY
Configuration: W345B Series II Material Handlers CDY00001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
345B, 345B Series II and W345B Series II Excavators Machine Systems
Media Number -SENR1934-11 Publication Date -01/01/2012 Date Updated -12/01/2012
i07191587
Swing Gear and Bearing - Install
SMCS - 7063-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3941 Link Bracket As 4
B
132-8223 Hydraulic Pump and Motor (115 V 50/60 Hz Single Phase)(1)
1
1U-6221 Hydraulic Torque Wrench 1
132-8143 36 mm Hex Link 1
C - Loctite 435 -
D 2P-9066 Lubricant 1
E 1U-8846 Gasket Sealant 1
F - Loctite C5A Copper Anti-Seize -
(1)
132-8231 Hydraulic Pump and Motor (220 V 50/60 Hz Single Phase) is also available.
Note: If the inner dust seal (3) and the outer dust seal (4) are installed dry, the new dust seals should
be installed dry in the swing gear and bearing.
Note: If the inner dust seal and the outer dust seal are bonded to the swing gear and bearing, the new
dust seals should be bonded to the swing gear and bearing.
Note: Perform Steps 1.a through 1.j to install the new dry dust seals.
Note: Perform Steps 2.a through 2.p to install the new dust seals that are bonded to the swing gear
and bearing.
1/6(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 1 g00636223
1. If inner dust seal (3) and outer dust seal (4) were installed dry, use the following procedure to install
the new dust seals:
a. Use a wire brush to thoroughly clean the grooves for the dust seal of the swing gear and
bearing. Make sure that all the dirt and foreign material has been removed.
b. Wash the grooves for the dust seal in a suitable solvent that will not leave an oily residue.
c. Make sure that the grooves for the dust seal in the swing gear and bearing are thoroughly clean
and dry prior to installation of the dust seals.
d. Cut one end of inner dust seal (3) at a 90 degree angle. Use a blunt tool to install the inner dust
seal in the seal groove of the swing gear and bearing.
e. Install the seal so that the lip of the seal is facing in the direction that is shown. Refer to
Illustration 1.
f. After the inner dust seal is installed in the seal groove, measure the seal and cut the remaining
end of the inner dust seal at a 90 degree angle. Install the remaining end of the inner dust seal
in the seal groove.
g. Make sure that the inner dust seal is seated properly in the seal groove, all the way around the
swing gear and bearing. Also, make sure that there is no gap between the ends of the inner dust
seal.
h. Pull each end of the inner dust seal out of the seal groove of the swing gear and bearing
approximately 50.8 mm (2.00 inch). Apply Tooling (C) to each end of the inner dust seal to
bond the seals together.
i. Immediately reinstall the inner dust seal in the seal groove of the swing gear and bearing.
Again, make sure that the entire inner dust seal is properly seated in the seal groove of the
swing gear and bearing. No gap should exist between the ends of the inner dust seal.
j. To ensure that the lip of inner dust seal has not adhered to the top of the bearing at the seal
joint, run a dull putty knife between the lip of the seal and the bearing at the seal joint.
k. Follow the procedure in Steps 1.a through 1.j to install outer dust seal (4) in the swing gear and
bearing. Refer to Illustration 1 for proper seal orientation in the swing gear and bearing.
2/6(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. 2. If inner dust seal (3) and outer dust seal (4) were bonded in the swing gear and bearing, use the
following procedure to install the new dust seals:
a. Thoroughly clean all the dirt and foreign material from the grooves for the dust seal in the
swing gear and bearing with a wire brush.
b. Wash the grooves for the dust seal in a suitable solvent that will not leave an oily residue.
c. Make sure that the grooves for the dust seals in the swing gear and bearing are thoroughly
clean and dry prior to installation of the dust seals.
Note: Install inner dust seal (3) and outer dust seal (4) in the swing gear and bearing in small
increments, because Tooling (C) cures very quickly.
d. Cut one end of inner dust seal (3) at a 90 degree angle.
e. Start applying Tooling (C) 50.8 mm (2.00 inch) from the cut end of the seal. Apply Tooling
(C) to the seal in 152.4 mm (6.00 inch) increments.
f. Immediately use a blunt tool to install only the bonded portion of the inner dust seal in the seal
groove of the swing gear and bearing. Make sure that the dust seal is seated properly in the
seal groove.
g. Install the seal so that the lip of the seal is facing in the direction that is shown. Refer to
Illustration 1.
h. To ensure that the inner dust seal has not adhered to the bearing, run a dull putty knife between
the lip of the seal and the bearing.
i. Apply Tooling (C) to the next 152.4 mm (6.00 inch) of the seal. Immediately use a blunt tool
to install only the bonded portion of the inner dust seal in the seal groove of the swing gear and
bearing.
j. Make sure that the inner dust seal is seated properly in the seal groove. Ensure that the inner
dust seal has not adhered to the bearing.
Note: Do not install the last 152.4 mm (6.00 inch) of the inner dust seal.
k. Repeat Steps 2.i through 2.j until the dust seal is installed.
l. Measure the inner dust seal and cut the remaining end of inner dust seal (3) at a 90 degree
angle. Install the last 152.4 mm (6.00 inch) of seal in the seal groove dry.
m. Make sure that the inner dust seal is properly seated in the seal groove and that there is no gap
between the seal ends. Carefully remove both loose ends of the inner dust seal out of the seal
groove.
n. Apply Tooling (C) to the loose ends of the seal.
o. Immediately use a blunt tool to reinstall the seal ends in the seal groove. Again, make sure that
the inner dust seal is properly seated in the seal groove, and that no gap existed between the
ends of the seal.
p. To ensure that the inner dust seal has not adhered to the top of the bearing, run a dull putty
knife around the seal.
q. Follow the procedure in Steps 2.a through 2.p to install outer dust seal (4) in the swing gear
and bearing. Refer to Illustration 1 for proper seal orientation in the swing gear and bearing.
3. Lubricate the swing gear and bearing with grease.
3/6(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 2 g00520664
Illustration 3 g00520674
Note: Clean the mating surface for the swing gear and bearing on the undercarriage frame assembly.
4. Apply Tooling (E) on the mating surface for the swing gear and bearing of the undercarriage frame
assembly.
5. Fasten Tooling (A) and a suitable lifting device to swing gear and bearing (1), as shown. Refer to
Illustration 2. The weight of swing gear and bearing (1) is approximately 660 kg (1455 lb).
6. Place the swing gear and bearing in the swing gear and bearing's original position on the
undercarriage frame assembly.
7. Make sure that the stamp "S" on the inner race is in the position that is shown, relative to the
undercarriage frame assembly and the stopper on the outer race. Refer to Illustration 3.
4/6(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...