The document provides instructions for assembling a fuel injection pump housing. It includes:
1) Installing bearings in both ends of the housing and ensuring proper positioning and clearance.
2) Installing the camshaft and securing it with a washer and snap ring.
3) Installing lifters and a fuel rack after assembling the governor.
Caterpillar cat el300 b excavator (prefix 3fj) service repair manual (3fj0000...fjjskekskem
The document provides instructions for assembling a fuel injection pump housing. It includes:
1) Installing bearings in both ends of the housing and ensuring proper depths and orientations.
2) Installing the camshaft and securing it with a washer and snap ring.
3) Checking that the camshaft has the specified end play clearance.
The assembly procedure involves installing various components in the correct order and ensuring proper placement and clearance specifications are met.
Caterpillar cat el300 b excavator (prefix 3fj) service repair manual (3fj0000...ujfjjskekfmmde
The document provides instructions for assembling a fuel injection pump housing. It describes:
1) Installing bearings in the governor and drive ends of the housing using installation tools.
2) Inserting the camshaft and installing a retaining washer and snap ring to secure it.
3) Ensuring proper end play of the camshaft during assembly.
The summary focuses on the key assembly steps and ensures the high level information is captured in under 3 sentences.
Caterpillar cat el300 b excavator (prefix 3fj) service repair manual (3fj0000...fjkskekdmmenm
The document provides instructions for assembling a fuel injection pump housing. It describes:
1) Installing bearings in the governor and drive ends of the housing using installation tools.
2) Inserting the camshaft and installing a retaining washer and snap ring to secure it.
3) Ensuring proper end play of the camshaft during assembly.
The summary covers the key assembly steps and components in 3 sentences as requested.
Caterpillar cat el300 b excavator (prefix 3fj) service repair manual (3fj0000...fhshefjjskefkem
The document provides instructions for assembling a fuel injection pump housing. It describes:
1) Installing bearings in the governor and drive ends of the housing using installation tools.
2) Inserting the camshaft and installing a retaining washer and snap ring to secure it.
3) Ensuring proper end play of the camshaft during assembly.
The summary covers the key assembly steps and components in 3 sentences as requested.
Caterpillar cat el300 b excavator (prefix 3fj) service repair manual (3fj0000...uuudfjjdjkskem
The document provides instructions for assembling a fuel injection pump housing. It describes:
1) Installing bearings in the governor and drive ends of the housing using installation tools.
2) Inserting the camshaft and installing a retaining washer and snap ring to secure it.
3) Ensuring proper end play of the camshaft during assembly.
The summary focuses on the key assembly steps and ensures the high level information is captured in under 3 sentences.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
Caterpillar cat el300 b excavator (prefix 3fj) service repair manual (3fj0000...fjjskekskem
The document provides instructions for assembling a fuel injection pump housing. It includes:
1) Installing bearings in both ends of the housing and ensuring proper depths and orientations.
2) Installing the camshaft and securing it with a washer and snap ring.
3) Checking that the camshaft has the specified end play clearance.
The assembly procedure involves installing various components in the correct order and ensuring proper placement and clearance specifications are met.
Caterpillar cat el300 b excavator (prefix 3fj) service repair manual (3fj0000...ujfjjskekfmmde
The document provides instructions for assembling a fuel injection pump housing. It describes:
1) Installing bearings in the governor and drive ends of the housing using installation tools.
2) Inserting the camshaft and installing a retaining washer and snap ring to secure it.
3) Ensuring proper end play of the camshaft during assembly.
The summary focuses on the key assembly steps and ensures the high level information is captured in under 3 sentences.
Caterpillar cat el300 b excavator (prefix 3fj) service repair manual (3fj0000...fjkskekdmmenm
The document provides instructions for assembling a fuel injection pump housing. It describes:
1) Installing bearings in the governor and drive ends of the housing using installation tools.
2) Inserting the camshaft and installing a retaining washer and snap ring to secure it.
3) Ensuring proper end play of the camshaft during assembly.
The summary covers the key assembly steps and components in 3 sentences as requested.
Caterpillar cat el300 b excavator (prefix 3fj) service repair manual (3fj0000...fhshefjjskefkem
The document provides instructions for assembling a fuel injection pump housing. It describes:
1) Installing bearings in the governor and drive ends of the housing using installation tools.
2) Inserting the camshaft and installing a retaining washer and snap ring to secure it.
3) Ensuring proper end play of the camshaft during assembly.
The summary covers the key assembly steps and components in 3 sentences as requested.
Caterpillar cat el300 b excavator (prefix 3fj) service repair manual (3fj0000...uuudfjjdjkskem
The document provides instructions for assembling a fuel injection pump housing. It describes:
1) Installing bearings in the governor and drive ends of the housing using installation tools.
2) Inserting the camshaft and installing a retaining washer and snap ring to secure it.
3) Ensuring proper end play of the camshaft during assembly.
The summary focuses on the key assembly steps and ensures the high level information is captured in under 3 sentences.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel filter base on an E240B excavator. The removal procedure involves using a strap wrench to remove the fuel filter, disconnecting fuel lines, and removing bolts and the fuel filter base. The installation procedure specifies cleaning parts, inspecting and replacing gaskets, reconnecting fuel lines and bolts to secure the fuel filter base.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding a spring-loaded cover in place and removing bolts to release the spring. Components like the filter screen, spring, piston and seals are then removed from the pump. The installation procedure is not described but presumably involves reversing the removal steps. Maintaining cleanliness of parts is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding a spring-loaded cover in place and removing bolts to release the spring. Components like the filter screen, spring, piston and seals are then removed from the pump. For installation, the components are reinstalled in reverse order, with care taken to ensure cleanliness and replace any worn parts. Precautions are listed to contain fluids and avoid injury from spring pressure.
This document provides instructions for removing and installing the fuel filter base on an E240B excavator. The removal procedure involves using a strap wrench to remove the fuel filter, disconnecting fuel lines, and removing bolts and the fuel filter base. The installation procedure specifies cleaning parts, inspecting and replacing gaskets, reconnecting fuel lines and bolts to secure the fuel filter base.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
Caterpillar cat 426 b backhoe loader (prefix 5yj) service repair manual (5yj0...fjkekfmefmm
This document provides instructions for servicing components of a Caterpillar 426B backhoe loader, including:
- Installing the front housing on the engine, ensuring proper alignment.
- Removing and installing the valve mechanism cover, replacing gaskets as needed.
- Disassembling, inspecting, and reassembling the rocker shaft assembly.
- Removing and reinstalling the rocker shaft and pushrods, ensuring proper identification and installation order of parts.
The summary focuses on the high-level steps for the key maintenance tasks described in the detailed document.
Komatsu WA470-3 Wheel Loader Service Repair Manual (WA470-3 Serial WA470H2005...zhan96lun
This document provides specifications, dimensions, weights, and other technical details for Komatsu wheel loaders. It includes specifications for machines up to a certain serial number, including dimensions and weights, performance data, and lists of recommended lubricants and fluids. It also provides an overview of service procedures and diagrams of vehicle controls and gauges.
Komatsu WA150PZ-5 Wheel Loader Service Repair Manual (SN H50051 and up).pdfzhan96lun
This document provides specifications and information about a WA150PZ-5 wheel loader, including:
- General assembly drawings and dimensions of the machine.
- Engine specifications including model, power, torque, and fuel consumption.
- Operating weights, bucket capacity, travel speeds, and other performance specs.
- Hydraulic system components and specifications.
- A weight table listing weights of individual machine components.
- A list of recommended lubricants and coolants for the machine and their specifications.
Komatsu HM400-2 Articulated Dump Truck Parts Catalogue Manual - SN A11001 AND...zhan96lun
This document provides part descriptions and numbers for engine components of the HM400-2 excavator from serial number A11001 and up. It includes sections for the cylinder head, rocker lever housing, rocker lever lever assembly, and rocker lever shaft assembly. Each section lists the relevant parts, descriptions, and quantities.
Komatsu HM400-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...zhan96lun
This document provides parts information for an HM400-1L excavator with serial number range A10001-UP. It includes a list of major systems and components with reference page numbers. An example parts list is then provided for the engine mounting system with part numbers, descriptions, and other specifications.
Komatsu HM350-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...zhan96lun
This document provides parts information for the engine and related systems of an HM350-1L machine with serial number A10001 or higher. It includes sections covering the engine mounting, hoses, air intake and exhaust piping, air cleaner components, and electrical harness. Lists of part numbers, descriptions, and quantities are provided for each system.
Komatsu HM350-1 Articulated Dump Truck Parts Catalogue Manual - SN 1001 AND U...zhan96lun
This document provides parts information for an HM350-1 excavator with serial numbers 1001 and up. It includes a list of major systems and subsystems for the excavator. For each part listed, it provides the part number, name, quantity, and applicable serial number range. The document contains detailed parts listings for various engine and cooling system components.
Komatsu HM300-3 Articulated Dump Truck Parts Catalogue Manual - SN 3001 AND U...zhan96lun
This document provides parts information for an HM300-3 excavator with serial numbers 3001 and up. It includes sections for the engine, cooling system, fuel system, electrical system, and other components. The cooling system section lists units for the radiator, aftercooler, coolant piping, brake oil cooler, and brake oil cooler piping. Parts are identified by index number, part number, description, and quantity for each component. The document provides detailed exploded diagrams and parts lists for replacement parts.
Komatsu HM300-2 Articulated Dump Truck Parts Catalogue Manual - SN 2001-2784.pdfzhan96lun
This document contains parts lists and specifications for various engine and drivetrain components of an HM300-2 excavator with serial number 2001-2784. It includes 17 sections with details on the engine mounting, hoses, piping, air conditioning parts, damper, and other related systems. The document provides part numbers, names, quantities and serial number ranges for each component listed.
Komatsu HM300-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...zhan96lun
This document provides parts information for an HM300-1L machine with serial number range A10001-UP. It includes a list of major system sections and references to additional documents for some component level part listings. Parts are identified by part number, description, and quantity.
This document provides instructions for removing and installing the fuel filter base on an E240B excavator. The removal procedure involves using a strap wrench to remove the fuel filter, disconnecting fuel lines, and removing bolts and the fuel filter base. The installation procedure specifies cleaning parts, inspecting and replacing gaskets, reconnecting fuel lines and bolts to secure the fuel filter base.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding a spring-loaded cover in place and removing bolts to release the spring. Components like the filter screen, spring, piston and seals are then removed from the pump. The installation procedure is not described but presumably involves reversing the removal steps. Maintaining cleanliness of parts is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding a spring-loaded cover in place and removing bolts to release the spring. Components like the filter screen, spring, piston and seals are then removed from the pump. For installation, the components are reinstalled in reverse order, with care taken to ensure cleanliness and replace any worn parts. Precautions are listed to contain fluids and avoid injury from spring pressure.
This document provides instructions for removing and installing the fuel filter base on an E240B excavator. The removal procedure involves using a strap wrench to remove the fuel filter, disconnecting fuel lines, and removing bolts and the fuel filter base. The installation procedure specifies cleaning parts, inspecting and replacing gaskets, reconnecting fuel lines and bolts to secure the fuel filter base.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
Caterpillar cat 426 b backhoe loader (prefix 5yj) service repair manual (5yj0...fjkekfmefmm
This document provides instructions for servicing components of a Caterpillar 426B backhoe loader, including:
- Installing the front housing on the engine, ensuring proper alignment.
- Removing and installing the valve mechanism cover, replacing gaskets as needed.
- Disassembling, inspecting, and reassembling the rocker shaft assembly.
- Removing and reinstalling the rocker shaft and pushrods, ensuring proper identification and installation order of parts.
The summary focuses on the high-level steps for the key maintenance tasks described in the detailed document.
Similar to Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001 and up).pdf (8)
Komatsu WA470-3 Wheel Loader Service Repair Manual (WA470-3 Serial WA470H2005...zhan96lun
This document provides specifications, dimensions, weights, and other technical details for Komatsu wheel loaders. It includes specifications for machines up to a certain serial number, including dimensions and weights, performance data, and lists of recommended lubricants and fluids. It also provides an overview of service procedures and diagrams of vehicle controls and gauges.
Komatsu WA150PZ-5 Wheel Loader Service Repair Manual (SN H50051 and up).pdfzhan96lun
This document provides specifications and information about a WA150PZ-5 wheel loader, including:
- General assembly drawings and dimensions of the machine.
- Engine specifications including model, power, torque, and fuel consumption.
- Operating weights, bucket capacity, travel speeds, and other performance specs.
- Hydraulic system components and specifications.
- A weight table listing weights of individual machine components.
- A list of recommended lubricants and coolants for the machine and their specifications.
Komatsu HM400-2 Articulated Dump Truck Parts Catalogue Manual - SN A11001 AND...zhan96lun
This document provides part descriptions and numbers for engine components of the HM400-2 excavator from serial number A11001 and up. It includes sections for the cylinder head, rocker lever housing, rocker lever lever assembly, and rocker lever shaft assembly. Each section lists the relevant parts, descriptions, and quantities.
Komatsu HM400-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...zhan96lun
This document provides parts information for an HM400-1L excavator with serial number range A10001-UP. It includes a list of major systems and components with reference page numbers. An example parts list is then provided for the engine mounting system with part numbers, descriptions, and other specifications.
Komatsu HM350-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...zhan96lun
This document provides parts information for the engine and related systems of an HM350-1L machine with serial number A10001 or higher. It includes sections covering the engine mounting, hoses, air intake and exhaust piping, air cleaner components, and electrical harness. Lists of part numbers, descriptions, and quantities are provided for each system.
Komatsu HM350-1 Articulated Dump Truck Parts Catalogue Manual - SN 1001 AND U...zhan96lun
This document provides parts information for an HM350-1 excavator with serial numbers 1001 and up. It includes a list of major systems and subsystems for the excavator. For each part listed, it provides the part number, name, quantity, and applicable serial number range. The document contains detailed parts listings for various engine and cooling system components.
Komatsu HM300-3 Articulated Dump Truck Parts Catalogue Manual - SN 3001 AND U...zhan96lun
This document provides parts information for an HM300-3 excavator with serial numbers 3001 and up. It includes sections for the engine, cooling system, fuel system, electrical system, and other components. The cooling system section lists units for the radiator, aftercooler, coolant piping, brake oil cooler, and brake oil cooler piping. Parts are identified by index number, part number, description, and quantity for each component. The document provides detailed exploded diagrams and parts lists for replacement parts.
Komatsu HM300-2 Articulated Dump Truck Parts Catalogue Manual - SN 2001-2784.pdfzhan96lun
This document contains parts lists and specifications for various engine and drivetrain components of an HM300-2 excavator with serial number 2001-2784. It includes 17 sections with details on the engine mounting, hoses, piping, air conditioning parts, damper, and other related systems. The document provides part numbers, names, quantities and serial number ranges for each component listed.
Komatsu HM300-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...zhan96lun
This document provides parts information for an HM300-1L machine with serial number range A10001-UP. It includes a list of major system sections and references to additional documents for some component level part listings. Parts are identified by part number, description, and quantity.
Komatsu D155C-1 Pipe Layer Parts Catalogue Manual - SN 15686 AND UP.pdfzhan96lun
This document provides parts information for a D155C-1 excavator with a SA6D140-2 engine installed. It includes lists of parts for the engine and its related systems, including the cooling system, fuel tank and piping, and electrical system. The parts are organized by section and item number, and each part includes its number, name, quantity, and applicable serial number range.
Deutz Fahr AGROTRON 265 Tractor Service Repair Manual.pdfzhan96lun
This document provides safety guidelines and instructions for workshop manuals on Agrotron tractors. It outlines general safety rules for working on machines, including ensuring proper ventilation, wearing protective equipment, and lifting heavy components safely. The document also describes how the manual is structured, with different sections covering mechanical systems, electrical systems, and removal/refitting procedures. Techniques for consulting the manual are provided, such as following the specific precautions for part removal and installation.
Deutz Fahr AGROTRON 235 Tractor Service Repair Manual.pdfzhan96lun
This document provides safety guidelines and instructions for workshop manuals on Agrotron tractors. It outlines general safety rules for working on machines, including ensuring proper ventilation, wearing protective equipment, and disconnecting battery terminals before working on electrical systems. It also describes how the manual is structured and how to consult it, noting removal and refitting procedures, safety precautions, lists of special tools, and proper tightening torques.
Deutz Fahr AGROTRON 210 Tractor Service Repair Manual.pdfzhan96lun
This document provides safety guidelines and instructions for workshop manuals on Agrotron tractors. It outlines general safety rules for working on machines, including ensuring proper ventilation, wearing protective equipment, and disconnecting battery terminals before working on electrical systems. It also describes how to safely remove and refit parts using lifting equipment, following torque specifications, and taking precautions for hydraulic and electrical systems. The manual is structured with separate sections covering mechanical systems, electrical systems, external components, and technical specifications without engine or transmission details.
Deutz Fahr AGROFARM 100 Tractor Service Repair Manual.pdfzhan96lun
This document provides the table of contents for a workshop manual for Agrofarm 85 and Agrofarm 100 tractors. The manual covers technical specifications, calibrations and electronic diagnosis, maintenance and repair methods, and wiring diagrams. It includes sections on the engine, transmission, axles, hydraulics, bodywork and more. The table of contents lists over 30 sections and subsections that provide information, part numbers, and instructions for repair and maintenance of components.
Deutz Fahr AGROFARM 85 Tractor Service Repair Manual.pdfzhan96lun
This document provides the table of contents for a workshop manual for Agrofarm 85 and Agrofarm 100 tractors. The manual covers technical specifications, calibrations and electronic diagnosis, maintenance and repair methods, and wiring diagrams. It includes sections on the engine, transmission, axles, hydraulics, bodywork and more. The table of contents lists over 30 sections and subsections that provide information, part numbers, and instructions for repair and maintenance of components.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: EL300B EXCAVATOR 3FJ
Configuration: E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWERED BY 3306T ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00935398
Automatic Timing Advance - Install
SMCS - 1272-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4186 Fuel Pump Timing Pin 1
B 0L-2070 Bolt 1
C 5P-7307 Engine Turning Tool 1
D 4C-9874 Spanner Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00476281
1. Install washer (1) and bolt (2). Ensure that the cover of the fuel pump housing is removed.
Turn the fuel pump camshaft in the direction of the engine rotation until Tool (A) can be
installed in the notch of the camshaft.
2. Install Tool (A) and (B) into position. Install the weight assembly for the timing advance on
the fuel injection pump camshaft.
Illustration 2 g00476286
3. Use Tool (D) on the automatic timing advance and maintain a constant torque of 68 N·m
(50 lb ft). Tighten the bolt that fastens the automatic timing advance to the fuel pump
camshaft to a torque of 270 ± 25 N·m (200 ± 18 lb ft).
4. Remove Tools (A), (B), (C) and (D). Install the starting motor.
End By: Install the front housing. Refer to Disassembly and Assembly, "Front Housing - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 19:57:47 UTC+0800 2019
2/2
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: EL300B EXCAVATOR 3FJ
Configuration: E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWERED BY 3306T ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07103919
Fuel Injection Pump Housing and Governor - Remove
SMCS - 1286-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2264 Pump Impeller Puller 1
8B-7560 Step Plate 1
0T-0513 Bolt 2
5P-1075 Hard Washer 2
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00589938
3304B Engine
1. On the 3304B engine, remove oil supply line (26), oil drain line (25), and heat shield (27).
Inspect the O-ring seal around oil drain line (25). Replace the O-ring seal if the O-ring seal
is damaged. Remove the gaskets and the screen from the top of the turbocharger.
Note: The following illustrations are of a 3306B engine.
Illustration 2 g00452289
2. Remove six nuts (1) and the washers and remove cover (2).
Note: Separate nut (1) and the mounting stud, if the nut and the mounting stud come out of
the housing together. Apply thread sealant to the mounting studs and reinstall the mounting
studs to a depth of 19.0 ± 0.8 mm (0.74 ± 0.03 inch).
2/5
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 3 g00452292
3. Remove center bolt (3) and spacer (4).
Illustration 4 g00452293
4. Install center bolt (3) and leave a gap of 6.4 mm (.25 inch). Install Tool (A), as shown.
Tighten the stud to loosen the fuel pump drive gear from the taper on the fuel injection
pump camshaft.
5. Remove Tool (A) and bolt (3).
Illustration 5 g00452301
3/5
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 6. Remove tube assemblies (5) and (11). Disconnect one end of tube assemblies (8) and (9).
Disconnect clamp (10). Remove two bolts (7) and the washers and remove filter base (6)
with the filter and the gasket.
Illustration 6 g00452302
7. Remove two bolts (12), the washers and the gasket. Remove two bolts (14) and the gasket.
Remove tube assembly (13).
Illustration 7 g00452343
8. Use a lifting sling and a hoist to secure the fuel injection pump housing and the governor.
Note: Remove the heat shield (not shown) if equipped.
9. Disconnect solenoid ground (15). Remove three nuts (17). Remove two bolts (16) and the
washers. Remove the fuel injection pump housing and the governor from the engine. To
safely remove the fuel injection pump housing and the governor, use two technicians or a
suitable lifting device. The weight of the 3304B fuel injection pump housing and governor
is 24 kg (53 lb). The weight of the 3306B fuel injection pump housing and governor is
32 Kg (70 lb).
10. Remove the O-ring seals from the fuel injection pump housing and the governor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 19:58:43 UTC+0800 2019
4/5
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: EL300B EXCAVATOR 3FJ
Configuration: E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWERED BY 3306T ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01139602
Fuel Injection Pump Housing - Disassemble
SMCS - 1253-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
Start By:
A. Disassemble the governor. Refer to Disassembly and Assembly, "Governor - Disassemble".
B. Remove the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g00456860
1. Remove cover (1) and the gasket.
Illustration 2 g00456923
2. Remove fuel rack (2) from the fuel injection pump housing.
Illustration 3 g00456924
2/5
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Note: If the original lifters are being reused in the fuel injection pump housing, place
identification marks on the lifters in order to identify the locations.
3. Remove lifters (3) from the fuel injection pump housing.
Illustration 4 g00456925
4. Position the fuel injection pump housing on wood blocks, as shown. Use Tool (A) in order
to remove snap ring (4) .
Illustration 5 g00456926
5. Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump
housing in order to loosen washer (5). Remove washer (5) .
3/5
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 6 g00456927
6. Remove camshaft (6) .
Illustration 7 g00456928
7. Remove bearings (7) from the drive end of the fuel injection pump housing.
Illustration 8 g00456930
8. Remove bearings (8) from the governor end of the fuel injection pump housing.
4/5
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 19:59:38 UTC+0800 2019
5/5
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: EL300B EXCAVATOR 3FJ
Configuration: E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWERED BY 3306T ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01138035
Fuel Injection Pump Housing - Assemble
SMCS - 1253-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
B 1P-0510 Driver Group 1
C
6V-2016 Plate 1
0S-1594 Bolt 2
6V-4818 Driver 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Put clean engine oil on all parts before assembly. Ensure that all of the oil passages are
clear.
1/6
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00457491
1. Use Tool (B) in order to install large bearing (1) in the governor end of the fuel injection
pump housing. Bearing joint (3) should be facing toward the top of the fuel injection pump
housing. Install the bearing so the bearing is 0.25 ± 0.20 mm (.010 ± .008 inch) below the
surface of the fuel injection pump housing.
2. Use Tool (B) in order to install small bearing (2) in the governor end of the fuel injection
pump so that Tool (B) is 7.16 ± 0.13 mm (.282 ± .005 inch) below the surface of the fuel
injection pump housing.
Illustration 2 g00457492
3. Use Tool (B) in order to install large bearing (4) in the drive end of the fuel injection pump
housing. The bearing joint should be facing toward the top of the fuel injection pump
housing. Install the bearing so the bearing is 1.00 ± 0.25 mm (.039 ± .010 inch) below the
surface of the fuel injection pump housing.
2/6
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 3 g00457493
4. Install the plate of Tool (C) on the drive end of the fuel injection pump in order to install
small bearing (5) for the rack. Use clean grease in order to hold the new driver for the rack
bearing of Tool (C). Install the driver and the bearing in the plate. Ensure that the groove in
the driver is aligned with the pin in the plate and use a hammer to push the bearing into
position. The bearing will be installed to the correct depth when the shoulder of the driver is
against the plate.
5. Remove Tool (C) from the fuel injection pump housing. The fuel rack bearing must be
installed so that the fuel rack bearing is 0.25 ± 0.25 mm (.010 ± .010 inch) below the surface
of the housing.
Illustration 4 g00457494
6. Install camshaft (6) .
3/6
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 5 g00458729
7. Put the fuel injection pump housing upright, as shown. Place a wood block under the
camshaft.
8. Put washer (7) over the end of the camshaft. Use Tool (B) and spacer (8) in order to push
the washer against the seat on the camshaft. Spacer (8) has an inside diameter of 38.1 mm
(1.50 inch) and a length of 31.75 mm (1.250 inch). The camshaft must have an end play of
0.18 ± 0.08 mm (.007 ± .003 inch) when the washer is pushed against the shoulder of the
camshaft.
Illustration 6 g00457495
9. Use Tool (A) in order to install snap ring (9) .
4/6
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 7 g00458730
Note: Check the condition of the new lifters. Replace the lifters, if necessary. If the original
lifters are being reused, place the lifters in the original locations. New lifters are identical,
and the new lifters can be placed in any order.
10. Install six lifters (10) in the fuel injection pump housing. Ensure that the groove in the lifter
is aligned with the pin in the fuel injection pump housing.
Illustration 8 g00458731
11. Install rack (11). Ensure that the groove in the end of the rack is aligned with the ear (tab) of
the fuel rack bearing that is at the drive end of the fuel injection pump housing.
5/6
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 9 g00458732
12. Install the gasket and cover (12) .
End By:
a. Assemble the governor. Refer to Disassembly and Assembly, "Governor - Assemble".
b. Install the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:00:34 UTC+0800 2019
6/6
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: EL300B EXCAVATOR 3FJ
Configuration: E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWERED BY 3306T ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01111133
Fuel Injection Pump Housing and Governor - Install
SMCS - 1286-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-7307 Engine Turning Tool 1
B 4C-9874 Spanner Wrench 1
C 6V-4186 Fuel Pump Timing Pin 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The No. 1 piston must be set at the top center position (TC) in order to perform all of the
timing procedures.
Note: The engine is seen from the flywheel end when the direction of the crankshaft rotation is
given.
1/6
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g00460164
1. Remove the electric starting motor.
2. Install Tool (A) into the flywheel housing, as shown.
3. To find the TC position for the No. 1 piston, perform the following procedure:
a. Turn the flywheel clockwise or turn the flywheel in the opposite direction of the
engine rotation for approximately 30 degrees. This removes all play from the timing
gears.
Note: If you go past the bolt hole, repeat Step 3.a.
Illustration 2 g00460248
b. Remove plugs (1) and (2) .
2/6
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 3 g00460252
c. Turn the flywheel counterclockwise until a 3/8-16 X 3 1/2 NC bolt (4) can be
installed in the flywheel through the hole in the flywheel housing. The No. 1 and No.
6 pistons are now at the TC position. Plug (2) was removed for viewing through
inspection hole (3) .
Note: The No. 1 piston is on the compression stroke when the valves of the No. 1
cylinder are closed. The rocker arms for the inlet valves and for the exhaust valves
must have slight side-to-side movement.
d. In order to check the position of the inlet and exhaust valves, remove the valve
mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover -
Remove and Install".
4. If the No. 1 piston is not on the compression stroke, remove bolt (4) and turn the flywheel
for 360 degrees counterclockwise. Install bolt (4). The No. 1 piston is now at the TC
position.
Illustration 4 g00460258
Typical example
3/6
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 5. Install Tool (C) in the fuel injection pump housing, as shown. Push on Tool (C) and turn
fuel injection pump camshaft (8). When Tool (C) engages the groove (slot) in the camshaft,
the fuel injection pump is in the TC position for the No. 1 piston.
Note: Check the condition of the O-ring seals. Replace the O-ring seals, if necessary.
6. Ensure that O-ring seals (5), (6), (7) and (9) are in position on the fuel injection pump
housing and the governor. Put clean engine oil on the seals.
Illustration 5 g00460259
7. Attach a hoist and put the fuel injection pump housing and the governor in position on the
timing gear plate and the oil manifold. Install three nuts (11), two bolts (10) and the
washers. Ensure that Tool (C) remains in place.
Illustration 6 g00460341
8. Install washer (12) with the large side outward. Install bolt (13) finger tight. Ensure that
Tool (C) is in the notch in the camshaft of the fuel injection pump.
4/6
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 7 g00460342
9. Install Tool (B) on the fuel pump drive gear. Apply 68 N·m (50 lb ft) of force to the fuel
pump drive gear with timing bolt (3) in position in the flywheel and Tool (C) in position in
the fuel system. Apply this force in a clockwise direction when the engine is viewed from
the front. Use Tool (B) and a suitable torque wrench. Hold the 68 N·m (50 lb ft) of force on
Tool (B) and torque the drive gear bolt to a torque of 270 ± 25 N·m (200 ± 18 lb ft).
Remove Tool (B) and Tool (C) from the fuel pump and remove bolt (3) from the flywheel.
10. Use Tool (A) and turn the flywheel for two complete revolutions. When bolt (3) goes in the
hole in the flywheel and Tool (C) is installed in the notch in the camshaft, the timing is
correct.
11. Install plugs (1) and (2) .
12. Remove Tool (A). Install the electric starting motor.
13. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Illustration 8 g00460343
14. Put cover (14) and the gasket in position. Install four bolts (15) .
15. Put the fuel filter base, the gasket, and fuel filter (16) in position. Install two bolts (19) and
the washers.
5/6
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 16. Install tube assemblies (21) and (22). Connect wire (20). Connect hoses (17) and (18) .
Illustration 9 g00589938
17. On the 3304B engines, install the strainer assembly in the turbocharger with the screen
downward. Install the gasket, the oil inlet line and the bolts. Install the O-ring seal on oil
drain line (25). Apply clean engine oil to the O-ring seal and install the gasket. Connect oil
drain line (25) and install the bolts. Install the clamps on the oil line.
Illustration 10 g00460346
18. Put cover (24) in position. Install nuts (23) and six washers. Tighten nuts (23) to a torque of
27 ± 7 N·m (20 ± 5 lb ft).
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:01:30 UTC+0800 2019
6/6
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: EL300B EXCAVATOR 3FJ
Configuration: E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWERED BY 3306T ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00886792
Governor - Disassemble
SMCS - 1264-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 6V-2163 Spring Clamp 1
C 1P-1855 Retaining Ring Pliers 1
Start By:
A. Remove the fuel injection pump housing and the governor. Refer to Disassembly and
Assembly, "Fuel Injection Pump Housing and Governor - Remove".
Note: To remove the governor for the disassembly of the fuel injection pump housing, perform
Steps 1, 2, 16, 22, 24, 25, 26, 27, 30, 32 and 34.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/12
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 1 g00453006
1. Remove fuel ratio control (1) from governor (2) .
Illustration 2 g00453007
Note: Illustration 2 shows the fuel ratio control that is still connected.
2. Remove six bolts (3), two bolts (5), housing (4) and the gasket.
Illustration 3 g00453008
2/12
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. 3. Remove governor spring (7), seat (6) and the washers.
Illustration 4 g00453009
4. Remove six bolts (8), cover (9) and the gasket. Use Tool (A) in order to remove seal (10) .
Illustration 5 g00453010
5. Remove low idle adjustment screw (12) and spring (11) .
3/12
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 6 g00453011
6. Remove shaft assembly (15) and levers (14) and (13) .
Illustration 7 g00453012
7. Remove two snap rings (19) from two pins (17). Remove two pins (17). Remove plates (16)
and stop (18) .
Illustration 8 g00453014
8. Remove pins (21) and (22) and remove spring (20) .
4/12
E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...