The document provides instructions for assembling a fuel injection pump housing. It includes:
1) Installing bearings in both ends of the housing and ensuring proper depths and orientations.
2) Installing the camshaft and securing it with a washer and snap ring.
3) Checking that the camshaft has the specified end play clearance.
The assembly procedure involves installing various components in the correct order and ensuring proper placement and clearance specifications are met.
Caterpillar cat 325 f lcr excavator (prefix xaa) service repair manual (xaa00...fjjskekdmme
This document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps for disassembly, including removing the head, check valve assemblies, fittings, seals, pistons, and other components. It then describes 11 steps for assembly, including installing seals, bearings, keys, and other parts in the reverse order of disassembly. Personal protective equipment is recommended and cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar cat 340 f l lre excavator (prefix ybf) service repair manual (ybf...f8isoeidkdk
This document provides the disassembly and assembly procedures for the travel motor on a 340F L LRE excavator. It includes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. The 27 steps to assemble list installing these same components in reverse order and include notes about lubrication, alignment and torque specifications. Required tools are listed for both procedures.
Caterpillar cat 420 d backhoe loader (prefix bmc) service repair manual (bmc0...ujfjjskkemm
The document provides instructions for removing and installing a front tie rod on a 420D backhoe loader. It lists the required tools which include a transmission repair stand. The removal process first requires removing the front axle from the machine. Safety precautions are provided to release hydraulic pressure and ensure cool oil before removing any hydraulic components or lines.
Caterpillar cat e200 b excavator (prefix 6kf) service repair manual (6kf00001...ufjdfjjkskemme
This service repair manual provides instructions for removing and installing various fuel system components on an E200B excavator powered by a 3116 engine, including:
1. The fuel priming pump and primary fuel filter.
2. The fuel transfer pump.
3. The fuel shutoff solenoid.
Detailed step-by-step procedures are provided with illustrations to guide the technician. Safety and contamination prevention procedures are also outlined. The manual is intended to ensure proper disassembly and reassembly of components.
Caterpillar cat 436 c backhoe loader (prefix 9jn) service repair manual (9jn0...fksejfjskekmm
1. The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054 engine.
2. The procedure includes lubricating the components, installing the pushrods and identifying marks, installing the rocker shaft assembly and securing it with nuts and bolts, and installing the valve mechanism cover.
3. Special attention is paid to ensuring proper alignment and torque specifications for a secure installation.
Caterpillar cat 311 b track type excavator (prefix 2ls) service repair manual...fjskefkemms
This document provides instructions for servicing components of a 311B excavator engine, including:
1) Instructions for assembling the rocker shaft, including the components and installation steps.
2) Instructions for installing the rocker shaft and pushrods, including torque specifications.
3) Instructions for removing the cylinder head, including removal steps and safety notices.
Caterpillar cat 428 d backhoe loader (prefix bxc) service repair manual (bxc0...ujdfjkkskmem
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifters
- Camshaft and camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep components clean and properly support parts.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before reinstallation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
Caterpillar cat 325 f lcr excavator (prefix xaa) service repair manual (xaa00...fjjskekdmme
This document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps for disassembly, including removing the head, check valve assemblies, fittings, seals, pistons, and other components. It then describes 11 steps for assembly, including installing seals, bearings, keys, and other parts in the reverse order of disassembly. Personal protective equipment is recommended and cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar cat 340 f l lre excavator (prefix ybf) service repair manual (ybf...f8isoeidkdk
This document provides the disassembly and assembly procedures for the travel motor on a 340F L LRE excavator. It includes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. The 27 steps to assemble list installing these same components in reverse order and include notes about lubrication, alignment and torque specifications. Required tools are listed for both procedures.
Caterpillar cat 420 d backhoe loader (prefix bmc) service repair manual (bmc0...ujfjjskkemm
The document provides instructions for removing and installing a front tie rod on a 420D backhoe loader. It lists the required tools which include a transmission repair stand. The removal process first requires removing the front axle from the machine. Safety precautions are provided to release hydraulic pressure and ensure cool oil before removing any hydraulic components or lines.
Caterpillar cat e200 b excavator (prefix 6kf) service repair manual (6kf00001...ufjdfjjkskemme
This service repair manual provides instructions for removing and installing various fuel system components on an E200B excavator powered by a 3116 engine, including:
1. The fuel priming pump and primary fuel filter.
2. The fuel transfer pump.
3. The fuel shutoff solenoid.
Detailed step-by-step procedures are provided with illustrations to guide the technician. Safety and contamination prevention procedures are also outlined. The manual is intended to ensure proper disassembly and reassembly of components.
Caterpillar cat 436 c backhoe loader (prefix 9jn) service repair manual (9jn0...fksejfjskekmm
1. The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054 engine.
2. The procedure includes lubricating the components, installing the pushrods and identifying marks, installing the rocker shaft assembly and securing it with nuts and bolts, and installing the valve mechanism cover.
3. Special attention is paid to ensuring proper alignment and torque specifications for a secure installation.
Caterpillar cat 311 b track type excavator (prefix 2ls) service repair manual...fjskefkemms
This document provides instructions for servicing components of a 311B excavator engine, including:
1) Instructions for assembling the rocker shaft, including the components and installation steps.
2) Instructions for installing the rocker shaft and pushrods, including torque specifications.
3) Instructions for removing the cylinder head, including removal steps and safety notices.
Caterpillar cat 428 d backhoe loader (prefix bxc) service repair manual (bxc0...ujdfjkkskmem
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifters
- Camshaft and camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep components clean and properly support parts.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before reinstallation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
The document provides instructions for assembling and disassembling components of the fuel system for a Caterpillar 3306B diesel engine, including:
1) Disassembling the fuel injection pump housing by removing internal components like the camshaft, lifters, and bearings.
2) Assembling the fuel injection pump housing by installing bearings, camshaft, and other internal components while applying clean engine oil as a lubricant.
3) Tools required for tasks like installing and removing snap rings on the housing.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...ufjskmdmdmed
The document provides instructions for assembling and disassembling components of the fuel injection system for a Caterpillar 3306B diesel engine, including:
1) Disassembling the fuel injection pump housing by removing internal components like the camshaft, lifters, and bearings.
2) Assembling the fuel injection pump housing by installing bearings, camshaft, and other internal components while applying clean engine oil as a lubricant.
3) Tools required for tasks like installing and removing snap rings on the camshaft.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...han647runken
The document provides instructions for assembling and disassembling components of the fuel injection system for a Caterpillar 3306B diesel engine, including:
1) Disassembling the fuel injection pump housing by removing internal components like the camshaft, lifters, and bearings.
2) Assembling the fuel injection pump housing by installing bearings, camshaft, and other internal components while applying clean engine oil as a lubricant.
3) Tools required for tasks like installing and removing snap rings from the housing.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...jfkksemmdmd
The document provides instructions for assembling a fuel injection pump housing. It includes:
1) Installing bearings in both ends of the housing and ensuring proper positioning and clearance.
2) Installing the camshaft and securing it with a washer and snap ring.
3) Installing lifters and a fuel rack after assembling the governor.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...jin465152tan
The document provides instructions for assembling and disassembling components of the fuel injection system for a Caterpillar 3306B diesel engine, including:
1) Disassembling the fuel injection pump housing by removing internal components like the camshaft, lifters, and bearings.
2) Assembling the fuel injection pump housing by installing bearings, camshaft, and other internal components while applying clean engine oil as a lubricant.
3) Tools required for tasks like installing and removing snap rings from the housing.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...zhan96lun
The document provides instructions for assembling a fuel injection pump housing. It includes:
1) Installing bearings in both ends of the housing and ensuring proper positioning and clearance.
2) Installing the camshaft and securing it with a washer and snap ring.
3) Installing lifters and a fuel rack after assembling the governor.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...f8usjejkdmmd
The document provides instructions for assembling and disassembling components of the fuel system for a Caterpillar 3306B diesel engine, including:
1) Disassembling the fuel injection pump housing by removing internal components like the camshaft, lifters, and bearings.
2) Assembling the fuel injection pump housing by installing bearings, camshaft, and other internal components while applying clean engine oil as a lubricant.
3) Tools required for tasks like installing and removing snap rings from the housing.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...f8usejdkdkdm3e4
The document provides instructions for assembling a fuel injection pump housing. It includes:
1) Installing bearings in both ends of the housing and ensuring proper positioning and clearance.
2) Installing the camshaft and securing it with a washer and snap ring.
3) Installing lifters and a fuel rack after assembling the governor.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...kbq6394287
The document provides instructions for assembling a fuel injection pump housing. It includes:
1) Installing bearings in both ends of the housing and ensuring proper positioning and clearance.
2) Installing the camshaft and securing it with a washer and snap ring.
3) Installing lifters and a fuel rack after assembling the governor.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...fujsked9dikdkd
The document provides instructions for assembling and disassembling components of the fuel injection system for a Caterpillar 3306B diesel engine, including:
1) Disassembling the fuel injection pump housing by removing internal components like the camshaft, lifters, and bearings.
2) Assembling the fuel injection pump housing by installing bearings, camshaft, and other internal components while applying clean engine oil as a lubricant.
3) Tools required for tasks like installing and removing snap rings from the housing.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...fujeikdmdmd5
The document provides instructions for assembling a fuel injection pump housing. It includes:
1) Installing bearings in both ends of the housing and ensuring proper positioning and clearance.
2) Installing the camshaft and securing it with a washer and snap ring.
3) Installing lifters and a fuel rack after assembling the governor.
Caterpillar cat d4 e track tractor (prefix 2cb) service repair manual (2cb000...ujjfjkskekmme
This document provides instructions for removing and installing the fuel injection pump housing and governor of a Caterpillar 3304B engine. The removal procedure involves disconnecting fuel lines and other components, then using lifting equipment to remove the housing due to its weight of 24-32 kg. The installation procedure describes preparing the housing, installing various bearings and seals, and timing the fuel pumps before reconnecting components.
Caterpillar cat d4 e track tractor (prefix 2cb) service repair manual (2cb000...fujsefkskekmm
This document provides instructions for removing and installing the fuel injection pump housing and governor of a Caterpillar 3304B engine. The removal procedure involves disconnecting fuel lines and other components, then using lifting equipment to remove the housing due to its weight of 24-32 kg. The installation procedure describes preparing and assembling components inside the housing, such as bearings and camshaft, and timing the installation on the engine.
Caterpillar cat d4 e track tractor (prefix 2cb) service repair manual (2cb000...fjsjfkskefmem
This document provides instructions for removing and disassembling the fuel injection pump housing and governor from a Caterpillar D4E track-type tractor powered by a 3304 engine. The removal procedure involves disconnecting fuel lines and other components, then using lifting equipment to remove the housing. The disassembly process describes removing various parts like covers, lifters, bearings, and the camshaft from the housing. The assembly section outlines installing bearings, the camshaft, washer and other parts back into the housing.
Caterpillar cat d4 e track tractor (prefix 2cb) service repair manual (2cb000...fjkskekdmmenm
This document provides instructions for removing and installing the fuel injection pump housing and governor of a Caterpillar 3304B engine. The removal procedure involves disconnecting fuel lines and other components, then using lifting equipment to remove the housing due to its weight of 24-32 kg. The installation procedure describes preparing and assembling components inside the housing, such as bearings and camshaft, and timing the installation on the engine.
Caterpillar cat d4 e track tractor (prefix 2cb) service repair manual (2cb000...ufjjjdjkkskme
This document provides instructions for removing and installing the fuel injection pump housing and governor of a Caterpillar 3304B engine. The removal procedure involves disconnecting fuel lines and other components, then using lifting equipment to remove the housing due to its weight of 24-32 kg. The installation procedure describes preparing the housing, installing various bearings and seals, and timing the fuel pumps before reconnecting components.
Caterpillar cat d4 e track tractor (prefix 2cb) service repair manual (2cb000...fjsjekksemm
This document provides instructions for removing and installing the fuel injection pump housing and governor on a Caterpillar 3304B engine. The removal procedure involves disconnecting fuel lines and other components, then using lifting equipment to remove the housing due to its weight of 24-32 kg. The installation procedure describes preparing and assembling components in the housing, setting bearing depths, and installing the housing on the engine while aligning timing pins.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
Yamaha outboard 40 veto, 40tr service repair manual l 544974 fjjskekskem
This document provides a service manual for 40V and 50H outboard motors. It includes an index listing chapters covering general information, specifications, periodic inspection and adjustment, fuel system, power unit, lower unit, bracket unit, electrical system, and trouble analysis. The general information chapter discusses identification, safety practices, special tools, measuring tools, and removal/installation tools. It provides guidance on safe work practices, the importance of using the proper tools, and cleaning and lubricating parts during disassembly and assembly.
Yamaha g9 ej golf cart service repair manualfjjskekskem
This document is a Yamaha service manual that provides information on servicing Yamaha G2 vehicles. It includes an index and table of contents that list chapters covering general information, specifications, inspection and adjustment procedures, engine overhaul, carburetion, power train, chassis, and electrical systems. The general information chapter provides details on vehicle identification numbers, important safety and maintenance tips, torque specifications, and a list of special tools required for tune-ups, engine service, power train service, chassis service, and electrical components.
More Related Content
Similar to Caterpillar cat el300 b excavator (prefix 3fj) service repair manual (3fj00001 and up)
The document provides instructions for assembling and disassembling components of the fuel system for a Caterpillar 3306B diesel engine, including:
1) Disassembling the fuel injection pump housing by removing internal components like the camshaft, lifters, and bearings.
2) Assembling the fuel injection pump housing by installing bearings, camshaft, and other internal components while applying clean engine oil as a lubricant.
3) Tools required for tasks like installing and removing snap rings on the housing.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...ufjskmdmdmed
The document provides instructions for assembling and disassembling components of the fuel injection system for a Caterpillar 3306B diesel engine, including:
1) Disassembling the fuel injection pump housing by removing internal components like the camshaft, lifters, and bearings.
2) Assembling the fuel injection pump housing by installing bearings, camshaft, and other internal components while applying clean engine oil as a lubricant.
3) Tools required for tasks like installing and removing snap rings on the camshaft.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...han647runken
The document provides instructions for assembling and disassembling components of the fuel injection system for a Caterpillar 3306B diesel engine, including:
1) Disassembling the fuel injection pump housing by removing internal components like the camshaft, lifters, and bearings.
2) Assembling the fuel injection pump housing by installing bearings, camshaft, and other internal components while applying clean engine oil as a lubricant.
3) Tools required for tasks like installing and removing snap rings from the housing.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...jfkksemmdmd
The document provides instructions for assembling a fuel injection pump housing. It includes:
1) Installing bearings in both ends of the housing and ensuring proper positioning and clearance.
2) Installing the camshaft and securing it with a washer and snap ring.
3) Installing lifters and a fuel rack after assembling the governor.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...jin465152tan
The document provides instructions for assembling and disassembling components of the fuel injection system for a Caterpillar 3306B diesel engine, including:
1) Disassembling the fuel injection pump housing by removing internal components like the camshaft, lifters, and bearings.
2) Assembling the fuel injection pump housing by installing bearings, camshaft, and other internal components while applying clean engine oil as a lubricant.
3) Tools required for tasks like installing and removing snap rings from the housing.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...zhan96lun
The document provides instructions for assembling a fuel injection pump housing. It includes:
1) Installing bearings in both ends of the housing and ensuring proper positioning and clearance.
2) Installing the camshaft and securing it with a washer and snap ring.
3) Installing lifters and a fuel rack after assembling the governor.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...f8usjejkdmmd
The document provides instructions for assembling and disassembling components of the fuel system for a Caterpillar 3306B diesel engine, including:
1) Disassembling the fuel injection pump housing by removing internal components like the camshaft, lifters, and bearings.
2) Assembling the fuel injection pump housing by installing bearings, camshaft, and other internal components while applying clean engine oil as a lubricant.
3) Tools required for tasks like installing and removing snap rings from the housing.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...f8usejdkdkdm3e4
The document provides instructions for assembling a fuel injection pump housing. It includes:
1) Installing bearings in both ends of the housing and ensuring proper positioning and clearance.
2) Installing the camshaft and securing it with a washer and snap ring.
3) Installing lifters and a fuel rack after assembling the governor.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...kbq6394287
The document provides instructions for assembling a fuel injection pump housing. It includes:
1) Installing bearings in both ends of the housing and ensuring proper positioning and clearance.
2) Installing the camshaft and securing it with a washer and snap ring.
3) Installing lifters and a fuel rack after assembling the governor.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...fujsked9dikdkd
The document provides instructions for assembling and disassembling components of the fuel injection system for a Caterpillar 3306B diesel engine, including:
1) Disassembling the fuel injection pump housing by removing internal components like the camshaft, lifters, and bearings.
2) Assembling the fuel injection pump housing by installing bearings, camshaft, and other internal components while applying clean engine oil as a lubricant.
3) Tools required for tasks like installing and removing snap rings from the housing.
Caterpillar Cat EL300B EXCAVATOR (Prefix 3FJ) Service Repair Manual (3FJ00001...fujeikdmdmd5
The document provides instructions for assembling a fuel injection pump housing. It includes:
1) Installing bearings in both ends of the housing and ensuring proper positioning and clearance.
2) Installing the camshaft and securing it with a washer and snap ring.
3) Installing lifters and a fuel rack after assembling the governor.
Caterpillar cat d4 e track tractor (prefix 2cb) service repair manual (2cb000...ujjfjkskekmme
This document provides instructions for removing and installing the fuel injection pump housing and governor of a Caterpillar 3304B engine. The removal procedure involves disconnecting fuel lines and other components, then using lifting equipment to remove the housing due to its weight of 24-32 kg. The installation procedure describes preparing the housing, installing various bearings and seals, and timing the fuel pumps before reconnecting components.
Caterpillar cat d4 e track tractor (prefix 2cb) service repair manual (2cb000...fujsefkskekmm
This document provides instructions for removing and installing the fuel injection pump housing and governor of a Caterpillar 3304B engine. The removal procedure involves disconnecting fuel lines and other components, then using lifting equipment to remove the housing due to its weight of 24-32 kg. The installation procedure describes preparing and assembling components inside the housing, such as bearings and camshaft, and timing the installation on the engine.
Caterpillar cat d4 e track tractor (prefix 2cb) service repair manual (2cb000...fjsjfkskefmem
This document provides instructions for removing and disassembling the fuel injection pump housing and governor from a Caterpillar D4E track-type tractor powered by a 3304 engine. The removal procedure involves disconnecting fuel lines and other components, then using lifting equipment to remove the housing. The disassembly process describes removing various parts like covers, lifters, bearings, and the camshaft from the housing. The assembly section outlines installing bearings, the camshaft, washer and other parts back into the housing.
Caterpillar cat d4 e track tractor (prefix 2cb) service repair manual (2cb000...fjkskekdmmenm
This document provides instructions for removing and installing the fuel injection pump housing and governor of a Caterpillar 3304B engine. The removal procedure involves disconnecting fuel lines and other components, then using lifting equipment to remove the housing due to its weight of 24-32 kg. The installation procedure describes preparing and assembling components inside the housing, such as bearings and camshaft, and timing the installation on the engine.
Caterpillar cat d4 e track tractor (prefix 2cb) service repair manual (2cb000...ufjjjdjkkskme
This document provides instructions for removing and installing the fuel injection pump housing and governor of a Caterpillar 3304B engine. The removal procedure involves disconnecting fuel lines and other components, then using lifting equipment to remove the housing due to its weight of 24-32 kg. The installation procedure describes preparing the housing, installing various bearings and seals, and timing the fuel pumps before reconnecting components.
Caterpillar cat d4 e track tractor (prefix 2cb) service repair manual (2cb000...fjsjekksemm
This document provides instructions for removing and installing the fuel injection pump housing and governor on a Caterpillar 3304B engine. The removal procedure involves disconnecting fuel lines and other components, then using lifting equipment to remove the housing due to its weight of 24-32 kg. The installation procedure describes preparing and assembling components in the housing, setting bearing depths, and installing the housing on the engine while aligning timing pins.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
Similar to Caterpillar cat el300 b excavator (prefix 3fj) service repair manual (3fj00001 and up) (20)
Yamaha outboard 40 veto, 40tr service repair manual l 544974 fjjskekskem
This document provides a service manual for 40V and 50H outboard motors. It includes an index listing chapters covering general information, specifications, periodic inspection and adjustment, fuel system, power unit, lower unit, bracket unit, electrical system, and trouble analysis. The general information chapter discusses identification, safety practices, special tools, measuring tools, and removal/installation tools. It provides guidance on safe work practices, the importance of using the proper tools, and cleaning and lubricating parts during disassembly and assembly.
Yamaha g9 ej golf cart service repair manualfjjskekskem
This document is a Yamaha service manual that provides information on servicing Yamaha G2 vehicles. It includes an index and table of contents that list chapters covering general information, specifications, inspection and adjustment procedures, engine overhaul, carburetion, power train, chassis, and electrical systems. The general information chapter provides details on vehicle identification numbers, important safety and maintenance tips, torque specifications, and a list of special tools required for tune-ups, engine service, power train service, chassis service, and electrical components.
Yale c875 gtp20 vx lift truck service repair manualfjjskekskem
The document provides service manual contents and procedures for removing an operator cab from various lift truck models. It contains the following key points:
- The operator cab is a separate unit that can be removed as a complete module from the frame.
- Steps include tilting the steering column, sliding the seat forward, disconnecting battery cables and air filter hoses, draining coolant by removing the radiator cap, and disconnecting heater hoses from the engine.
- Additional steps apply for models with air conditioning, which require extracting refrigerant from the AC system and disconnecting refrigerant lines.
- Removing the cab doors requires two people. Proper safety precautions must be followed when working on
Yale a909 gdp90 vx lift truck service repair manualfjjskekskem
The document provides instructions to remove an operator cab from various lift truck models. Key steps include:
1. Tilting the steering column, sliding the seat forward, opening doors and hood to access components.
2. Disconnecting air filter hoses, radiator hoses, heater hoses, and refrigerant lines from the engine and air conditioning system.
3. Removing door assemblies by disconnecting gas springs and hinges.
4. Disconnecting electrical connections for heaters and controls.
The instructions provide cab removal procedures for different lift truck models and components like air conditioning. Safety warnings are included to avoid burns from hot fluids.
Perkins 1600 series industrial engine (xgf) service repair manualfjjskekskem
This document provides troubleshooting information for 1600 series industrial engines. It contains important safety information and warns of potential hazards. The document is divided into sections covering electronic troubleshooting, diagnostic trouble codes, functional tests, and an index. Safety precautions are marked and procedures are given to minimize risk of damage to electronic components during welding.
Perkins 1600 series industrial engine (xga ) service repair manualfjjskekskem
This document provides instructions for the disassembly and assembly of components for 1600 series industrial engines. It begins with important safety information, warning that improper operation, maintenance or repair can be dangerous. The document provides procedures for removing and installing components like the fuel filter base, electronic unit injectors, turbocharger, exhaust manifolds, valves, pumps and seals. Safety precautions are emphasized throughout.
Perkins 1200 series 1206 e e70tta industrial engine service repair manualfjjskekskem
This document provides troubleshooting information for an electronic engine control system. It includes a system overview describing the main components, including the electronic control module (ECM), sensors, and actuators. It also includes block diagrams illustrating the overall system and control circuit. The document then describes how the system operates, covering topics like engine governing, fuel injection, and customer-specified parameters. Finally, it includes troubleshooting sections for diagnosing issues based on symptoms, diagnostic codes, or functional tests.
Daewoo doosan solar 030 plus mini crawler excavator parts catalogue manual (s...fjjskekskem
This document provides a repair kit parts list and descriptions for a Solar 030Plus engine with serial numbers between 20001 and 20575. The repair kit part number is 587814-0710 and includes seals, gaskets, packings and other parts to repair the cylinder head, cylinder block, timing gear case, flywheel housing, oil pan, oil pump, piston and crankshaft assembly. A total of 76 individual parts are included in the repair kit.
Daewoo doosan solar 015 plus mini crawler excavator parts catalogue manual (s...fjjskekskem
This document provides a parts list for the crank case of a Solar 015Plus engine. It includes 3 pages listing over 50 individual parts that make up the crank case assembly, including covers, gaskets, cylinders, bolts, pins, bushings, seals, and more. Each part is given a key number, part number, description, and quantity. Serial numbers and whether the part is replaceable are also provided for each item.
Daewoo doosan solar 015 plus mini crawler excavator parts catalogue manualfjjskekskem
The document provides a parts list for a crank case assembly with 33 parts. It lists the part numbers, descriptions, quantities, and whether the parts are replaceable for each component. It also includes keys for three piston sizes and their ring sets.
The document contains a parts list for an oil pan and gear case assembly with 14 parts. It lists the part numbers, descriptions, quantities, and whether the parts are replaceable for each component.
The document provides an exploded diagram and parts list for a fuel injection pump with 24 parts. It lists the part numbers, descriptions, quantities, and whether the parts are replaceable for each component.
Daewoo doosan solar 015 mini crawler excavator parts catalogue manualfjjskekskem
This document contains 18 figures describing parts related to the engine of a Solar 015 machine. Each figure includes an illustration of the part and lists relevant part numbers, descriptions, quantities and other identifying information. Key components described include the cylinder block, oil pan, cylinder head, timing gear case, cam shaft, pistons, crankshaft, flywheel and other internal engine parts.
Daewoo doosan solar 010 mini crawler excavator parts catalogue manual (sn 200...fjjskekskem
The document provides a list of parts for various components of a solar engine, including the cylinder block, timing gear housing, flywheel housing, cylinder head, suction manifold, and camshaft. It includes the part numbers, descriptions, quantities, and other identifying information for 25 different parts per component. The parts are identified numerically and organized by the component they belong to.
Daewoo doosan solar 010 mini crawler excavator parts catalogue manualfjjskekskem
This document contains diagrams and part numbers for various engine components of a cylinder block, including:
- The cylinder block assembly and individual parts like the cylinder block, plugs, bolts, bearings, and bushings.
- It also includes diagrams and part numbers for components of the crankshaft and piston like the crankshaft, piston, connecting rod, and bearing.
- Finally, it lists parts for the timing gear housing, flywheel housing, oil pump, and related gaskets and seals. The document provides detailed exploded views and part numbers for replacement of engine subassemblies and individual parts.
Daewoo doosan mt41 moxy articulated dump truck parts catalogue manualfjjskekskem
This document contains parts lists and diagrams for various engine components of an MT36/41 engine with serial numbers 810001-810108. It includes lists and diagrams for the cylinder head, rocker cover, cylinder block, flywheel housing, oil sump, front casing, crankcase ventilation, crank mechanism, piston, timing gear, and oil pump. The parts are identified by key number, part number, description, and quantity.
Daewoo doosan mt40 b moxy articulated dump truck parts catalogue manualfjjskekskem
This document contains parts lists and diagrams for various components of a MT40B engine with serial numbers 513001-513140. It includes lists and diagrams for the cylinder head, rocker cover, cylinder block, timing gear housing, flywheel housing, oil sump, crankcase ventilation, and crank mechanism. Each component list includes part numbers, descriptions, quantities, and whether parts are replaceable. Diagrams provide visuals and callouts for the components.
Daewoo doosan mt36 moxy articulated dump truck parts catalogue manual sn 41...fjjskekskem
This document provides parts information for the cylinder head, rocker cover, cylinder block, flywheel housing, oil sump, crankcase ventilation, housing, crank mechanism, piston, and timing gear of an MT36 engine with serial numbers 410001-410309. It includes diagrams of each assembly or component along with a parts list detailing part numbers, descriptions, quantities, and other identifying information for each part.
Daewoo doosan mt36 moxy articulated dump truck parts catalogue manualfjjskekskem
This document contains parts lists and diagrams for various engine components of an MT36/41 engine with serial numbers 810001-810108. It includes lists and diagrams for the cylinder head, rocker cover, cylinder block, flywheel housing, oil sump, front casing, crankcase ventilation, crank mechanism, piston, timing gear, and oil pump. The parts are identified by key number, part number, description, and quantity.
Daewoo doosan mt31 moxy articulated dump truck parts catalogue manual sn 71...fjjskekskem
This document provides parts information for the crankcase ventilation, engine suspension, charge air pipes, cylinder head, rocker cover, cylinder block, flywheel housing, oil sump, crankshaft mechanism, and piston of an engine. It includes diagrams of these systems and lists the part numbers, descriptions, quantities, and serial number ranges for each component. The parts are identified by key number in the diagrams and parts lists.
Daewoo doosan mt31 moxy articulated dump truck parts catalogue manual sn 71...fjjskekskem
This document provides an exploded diagram and parts list for the engine suspension of a marine diesel engine. It includes over 320 individual part numbers, descriptions, quantities, and other identifying information for components of the engine block, cylinder head, valve train, crankcase, oil pan, and other internal engine systems. The parts list is separated into 18 figures that diagram the major engine assemblies and sub-assemblies down to the individual part level.
Daewoo doosan mt26 moxy articulated dump truck parts catalogue manual sn 71...fjjskekskem
This document provides parts information for the crankcase ventilation, engine suspension, charge air pipes, cylinder head, rocker cover, cylinder block, flywheel housing, oil sump, crankshaft mechanism, and piston of an engine. It includes diagrams of these systems and lists the part numbers, descriptions, quantities, and serial number ranges for each component. The parts are identified by key number in the diagrams and parts lists.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: EL300B EXCAVATOR 3FJ
Configuration: E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWERED BY 3306T ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00935398
Automatic Timing Advance - Install
SMCS - 1272-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4186 Fuel Pump Timing Pin 1
B 0L-2070 Bolt 1
C 5P-7307 Engine Turning Tool 1
D 4C-9874 Spanner Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00476281
1. Install washer (1) and bolt (2). Ensure that the cover of the fuel pump housing is removed.
Turn the fuel pump camshaft in the direction of the engine rotation until Tool (A) can be
installed in the notch of the camshaft.
2. Install Tool (A) and (B) into position. Install the weight assembly for the timing advance on
the fuel injection pump camshaft.
Illustration 2 g00476286
3. Use Tool (D) on the automatic timing advance and maintain a constant torque of 68 N�m
(50 lb ft). Tighten the bolt that fastens the automatic timing advance to the fuel pump
camshaft to a torque of 270 � 25 N�m (200 � 18 lb ft).
4. Remove Tools (A), (B), (C) and (D). Install the starting motor.
End By: Install the front housing. Refer to Disassembly and Assembly, "Front Housing - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 19:57:47 UTC+0800 2019
2/2E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: EL300B EXCAVATOR 3FJ
Configuration: E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWERED BY 3306T ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07103919
Fuel Injection Pump Housing and Governor - Remove
SMCS - 1286-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2264 Pump Impeller Puller 1
8B-7560 Step Plate 1
0T-0513 Bolt 2
5P-1075 Hard Washer 2
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00589938
3304B Engine
1. On the 3304B engine, remove oil supply line (26), oil drain line (25), and heat shield (27).
Inspect the O-ring seal around oil drain line (25). Replace the O-ring seal if the O-ring seal
is damaged. Remove the gaskets and the screen from the top of the turbocharger.
Note: The following illustrations are of a 3306B engine.
Illustration 2 g00452289
2. Remove six nuts (1) and the washers and remove cover (2).
Note: Separate nut (1) and the mounting stud, if the nut and the mounting stud come out of
the housing together. Apply thread sealant to the mounting studs and reinstall the mounting
studs to a depth of 19.0 � 0.8 mm (0.74 � 0.03 inch).
2/5E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 3 g00452292
3. Remove center bolt (3) and spacer (4).
Illustration 4 g00452293
4. Install center bolt (3) and leave a gap of 6.4 mm (.25 inch). Install Tool (A), as shown.
Tighten the stud to loosen the fuel pump drive gear from the taper on the fuel injection
pump camshaft.
5. Remove Tool (A) and bolt (3).
Illustration 5 g00452301
3/5E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 6. Remove tube assemblies (5) and (11). Disconnect one end of tube assemblies (8) and (9).
Disconnect clamp (10). Remove two bolts (7) and the washers and remove filter base (6)
with the filter and the gasket.
Illustration 6 g00452302
7. Remove two bolts (12), the washers and the gasket. Remove two bolts (14) and the gasket.
Remove tube assembly (13).
Illustration 7 g00452343
8. Use a lifting sling and a hoist to secure the fuel injection pump housing and the governor.
Note: Remove the heat shield (not shown) if equipped.
9. Disconnect solenoid ground (15). Remove three nuts (17). Remove two bolts (16) and the
washers. Remove the fuel injection pump housing and the governor from the engine. To
safely remove the fuel injection pump housing and the governor, use two technicians or a
suitable lifting device. The weight of the 3304B fuel injection pump housing and governor
is 24 kg (53 lb). The weight of the 3306B fuel injection pump housing and governor is
32 Kg (70 lb).
10. Remove the O-ring seals from the fuel injection pump housing and the governor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 19:58:43 UTC+0800 2019
4/5E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: EL300B EXCAVATOR 3FJ
Configuration: E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWERED BY 3306T ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01139602
Fuel Injection Pump Housing - Disassemble
SMCS - 1253-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
Start By:
A. Disassemble the governor. Refer to Disassembly and Assembly, "Governor - Disassemble".
B. Remove the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g00456860
1. Remove cover (1) and the gasket.
Illustration 2 g00456923
2. Remove fuel rack (2) from the fuel injection pump housing.
Illustration 3 g00456924
2/5E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Note: If the original lifters are being reused in the fuel injection pump housing, place
identification marks on the lifters in order to identify the locations.
3. Remove lifters (3) from the fuel injection pump housing.
Illustration 4 g00456925
4. Position the fuel injection pump housing on wood blocks, as shown. Use Tool (A) in order
to remove snap ring (4) .
Illustration 5 g00456926
5. Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump
housing in order to loosen washer (5). Remove washer (5) .
3/5E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 6 g00456927
6. Remove camshaft (6) .
Illustration 7 g00456928
7. Remove bearings (7) from the drive end of the fuel injection pump housing.
Illustration 8 g00456930
8. Remove bearings (8) from the governor end of the fuel injection pump housing.
4/5E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 19:59:38 UTC+0800 2019
5/5E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: EL300B EXCAVATOR 3FJ
Configuration: E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWERED BY 3306T ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01138035
Fuel Injection Pump Housing - Assemble
SMCS - 1253-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
B 1P-0510 Driver Group 1
C
6V-2016 Plate 1
0S-1594 Bolt 2
6V-4818 Driver 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Put clean engine oil on all parts before assembly. Ensure that all of the oil passages are
clear.
1/6E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00457491
1. Use Tool (B) in order to install large bearing (1) in the governor end of the fuel injection
pump housing. Bearing joint (3) should be facing toward the top of the fuel injection pump
housing. Install the bearing so the bearing is 0.25 � 0.20 mm (.010 � .008 inch) below the
surface of the fuel injection pump housing.
2. Use Tool (B) in order to install small bearing (2) in the governor end of the fuel injection
pump so that Tool (B) is 7.16 � 0.13 mm (.282 � .005 inch) below the surface of the fuel
injection pump housing.
Illustration 2 g00457492
3. Use Tool (B) in order to install large bearing (4) in the drive end of the fuel injection pump
housing. The bearing joint should be facing toward the top of the fuel injection pump
housing. Install the bearing so the bearing is 1.00 � 0.25 mm (.039 � .010 inch) below the
surface of the fuel injection pump housing.
2/6E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 3 g00457493
4. Install the plate of Tool (C) on the drive end of the fuel injection pump in order to install
small bearing (5) for the rack. Use clean grease in order to hold the new driver for the rack
bearing of Tool (C). Install the driver and the bearing in the plate. Ensure that the groove in
the driver is aligned with the pin in the plate and use a hammer to push the bearing into
position. The bearing will be installed to the correct depth when the shoulder of the driver is
against the plate.
5. Remove Tool (C) from the fuel injection pump housing. The fuel rack bearing must be
installed so that the fuel rack bearing is 0.25 � 0.25 mm (.010 � .010 inch) below the surface
of the housing.
Illustration 4 g00457494
6. Install camshaft (6) .
3/6E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 5 g00458729
7. Put the fuel injection pump housing upright, as shown. Place a wood block under the
camshaft.
8. Put washer (7) over the end of the camshaft. Use Tool (B) and spacer (8) in order to push
the washer against the seat on the camshaft. Spacer (8) has an inside diameter of 38.1 mm
(1.50 inch) and a length of 31.75 mm (1.250 inch). The camshaft must have an end play of
0.18 � 0.08 mm (.007 � .003 inch) when the washer is pushed against the shoulder of the
camshaft.
Illustration 6 g00457495
9. Use Tool (A) in order to install snap ring (9) .
4/6E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 7 g00458730
Note: Check the condition of the new lifters. Replace the lifters, if necessary. If the original
lifters are being reused, place the lifters in the original locations. New lifters are identical,
and the new lifters can be placed in any order.
10. Install six lifters (10) in the fuel injection pump housing. Ensure that the groove in the lifter
is aligned with the pin in the fuel injection pump housing.
Illustration 8 g00458731
11. Install rack (11). Ensure that the groove in the end of the rack is aligned with the ear (tab) of
the fuel rack bearing that is at the drive end of the fuel injection pump housing.
5/6E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 9 g00458732
12. Install the gasket and cover (12) .
End By:
a. Assemble the governor. Refer to Disassembly and Assembly, "Governor - Assemble".
b. Install the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:00:34 UTC+0800 2019
6/6E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: EL300B EXCAVATOR 3FJ
Configuration: E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWERED BY 3306T ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01111133
Fuel Injection Pump Housing and Governor - Install
SMCS - 1286-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-7307 Engine Turning Tool 1
B 4C-9874 Spanner Wrench 1
C 6V-4186 Fuel Pump Timing Pin 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The No. 1 piston must be set at the top center position (TC) in order to perform all of the
timing procedures.
Note: The engine is seen from the flywheel end when the direction of the crankshaft rotation is
given.
1/6E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g00460164
1. Remove the electric starting motor.
2. Install Tool (A) into the flywheel housing, as shown.
3. To find the TC position for the No. 1 piston, perform the following procedure:
a. Turn the flywheel clockwise or turn the flywheel in the opposite direction of the
engine rotation for approximately 30 degrees. This removes all play from the timing
gears.
Note: If you go past the bolt hole, repeat Step 3.a.
Illustration 2 g00460248
b. Remove plugs (1) and (2) .
2/6E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 3 g00460252
c. Turn the flywheel counterclockwise until a 3/8-16 X 3 1/2 NC bolt (4) can be
installed in the flywheel through the hole in the flywheel housing. The No. 1 and No.
6 pistons are now at the TC position. Plug (2) was removed for viewing through
inspection hole (3) .
Note: The No. 1 piston is on the compression stroke when the valves of the No. 1
cylinder are closed. The rocker arms for the inlet valves and for the exhaust valves
must have slight side-to-side movement.
d. In order to check the position of the inlet and exhaust valves, remove the valve
mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover -
Remove and Install".
4. If the No. 1 piston is not on the compression stroke, remove bolt (4) and turn the flywheel
for 360 degrees counterclockwise. Install bolt (4). The No. 1 piston is now at the TC
position.
Illustration 4 g00460258
Typical example
3/6E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 5. Install Tool (C) in the fuel injection pump housing, as shown. Push on Tool (C) and turn
fuel injection pump camshaft (8). When Tool (C) engages the groove (slot) in the camshaft,
the fuel injection pump is in the TC position for the No. 1 piston.
Note: Check the condition of the O-ring seals. Replace the O-ring seals, if necessary.
6. Ensure that O-ring seals (5), (6), (7) and (9) are in position on the fuel injection pump
housing and the governor. Put clean engine oil on the seals.
Illustration 5 g00460259
7. Attach a hoist and put the fuel injection pump housing and the governor in position on the
timing gear plate and the oil manifold. Install three nuts (11), two bolts (10) and the
washers. Ensure that Tool (C) remains in place.
Illustration 6 g00460341
8. Install washer (12) with the large side outward. Install bolt (13) finger tight. Ensure that
Tool (C) is in the notch in the camshaft of the fuel injection pump.
4/6E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 7 g00460342
9. Install Tool (B) on the fuel pump drive gear. Apply 68 N�m (50 lb ft) of force to the fuel
pump drive gear with timing bolt (3) in position in the flywheel and Tool (C) in position in
the fuel system. Apply this force in a clockwise direction when the engine is viewed from
the front. Use Tool (B) and a suitable torque wrench. Hold the 68 N�m (50 lb ft) of force on
Tool (B) and torque the drive gear bolt to a torque of 270 � 25 N�m (200 � 18 lb ft).
Remove Tool (B) and Tool (C) from the fuel pump and remove bolt (3) from the flywheel.
10. Use Tool (A) and turn the flywheel for two complete revolutions. When bolt (3) goes in the
hole in the flywheel and Tool (C) is installed in the notch in the camshaft, the timing is
correct.
11. Install plugs (1) and (2) .
12. Remove Tool (A). Install the electric starting motor.
13. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Illustration 8 g00460343
14. Put cover (14) and the gasket in position. Install four bolts (15) .
15. Put the fuel filter base, the gasket, and fuel filter (16) in position. Install two bolts (19) and
the washers.
5/6E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 16. Install tube assemblies (21) and (22). Connect wire (20). Connect hoses (17) and (18) .
Illustration 9 g00589938
17. On the 3304B engines, install the strainer assembly in the turbocharger with the screen
downward. Install the gasket, the oil inlet line and the bolts. Install the O-ring seal on oil
drain line (25). Apply clean engine oil to the O-ring seal and install the gasket. Connect oil
drain line (25) and install the bolts. Install the clamps on the oil line.
Illustration 10 g00460346
18. Put cover (24) in position. Install nuts (23) and six washers. Tighten nuts (23) to a torque of
27 � 7 N�m (20 � 5 lb ft).
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:01:30 UTC+0800 2019
6/6E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: EL300B EXCAVATOR 3FJ
Configuration: E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWERED BY 3306T ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00886792
Governor - Disassemble
SMCS - 1264-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 6V-2163 Spring Clamp 1
C 1P-1855 Retaining Ring Pliers 1
Start By:
A. Remove the fuel injection pump housing and the governor. Refer to Disassembly and
Assembly, "Fuel Injection Pump Housing and Governor - Remove".
Note: To remove the governor for the disassembly of the fuel injection pump housing, perform
Steps 1, 2, 16, 22, 24, 25, 26, 27, 30, 32 and 34.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/12E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 1 g00453006
1. Remove fuel ratio control (1) from governor (2) .
Illustration 2 g00453007
Note: Illustration 2 shows the fuel ratio control that is still connected.
2. Remove six bolts (3), two bolts (5), housing (4) and the gasket.
Illustration 3 g00453008
2/12E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. 3. Remove governor spring (7), seat (6) and the washers.
Illustration 4 g00453009
4. Remove six bolts (8), cover (9) and the gasket. Use Tool (A) in order to remove seal (10) .
Illustration 5 g00453010
5. Remove low idle adjustment screw (12) and spring (11) .
3/12E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 6 g00453011
6. Remove shaft assembly (15) and levers (14) and (13) .
Illustration 7 g00453012
7. Remove two snap rings (19) from two pins (17). Remove two pins (17). Remove plates (16)
and stop (18) .
Illustration 8 g00453014
8. Remove pins (21) and (22) and remove spring (20) .
4/12E300B, EL300B TRACK-TYPE EXCAVATORS 3FJ00001-UP (MACHINE) POWE...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...