This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...fjjskekfsem
This document provides instructions for removing and installing the fuel transfer pump on an excavator model E240B powered by a 3116 engine. The removal procedure involves holding the spring loaded cover in place and removing bolts to access internal components. Components like the filter screen, seals, fittings and check valves are also removed. The installation procedure is not described but references are provided to check component reusability. Proper containment of fluids is emphasized during maintenance.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...ufjjsjekksemmd
1) The document provides instructions for removing and installing the fuel filter base, fuel priming pump, primary fuel filter, and fuel transfer pump on an E240B excavator.
2) The removal procedures describe disconnecting fuel lines and removing mounting bolts, filters, bases, and other components.
3) The installation procedures describe inspecting parts, lubricating with oil, and reversing the removal steps to mount components with new seals or gaskets if needed. Safety notices are provided throughout.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...fjkskekdmmenm
This document provides instructions for removing and installing the fuel transfer pump on an excavator model E240B powered by a 3116 engine. The removal procedure involves holding the spring loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to avoid contamination.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...uufjdjdkkksmem
1) The document provides instructions for removing and installing the fuel filter base, fuel priming pump, primary fuel filter, and fuel transfer pump on an E240B excavator.
2) The removal procedures describe disconnecting fuel lines and removing mounting bolts, filters, bases, and other components.
3) The installation procedures describe inspecting parts, lubricating with oil, and reversing the removal steps to mount components with new seals or gaskets if needed. Special care is required when installing spring-loaded parts.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...fjsjefskekfmme
This document provides instructions for removing and installing the fuel transfer pump on an excavator model E240B powered by a 3116 engine. The removal procedure involves holding the spring loaded cover in place and removing bolts to access internal components. Components like the filter screen, seals, springs and fittings are then removed. The installation procedure is not described but presumably involves reversing the removal steps. Precautions are provided to contain fluids and prevent contamination.
Caterpillar cat e200 b excavator (prefix 6kf) service repair manual (6kf00001...fjseazqkkdmmem
This service repair manual provides instructions for removing and installing various fuel system components on an E200B excavator powered by a 3116 engine, including:
1. The fuel priming pump and primary fuel filter.
2. The fuel transfer pump.
3. The fuel shutoff solenoid.
Detailed step-by-step procedures are provided with illustrations to guide the technician. Safety and contamination prevention procedures are also outlined. The manual is intended to ensure proper disassembly and reassembly of components.
Caterpillar cat e200 b excavator (prefix 6kf) service repair manual (6kf00001...ufjdfjjkskemme
This service repair manual provides instructions for removing and installing various fuel system components on an E200B excavator powered by a 3116 engine, including:
1. The fuel priming pump and primary fuel filter.
2. The fuel transfer pump.
3. The fuel shutoff solenoid.
Detailed step-by-step procedures are provided with illustrations to guide the technician. Safety and contamination prevention procedures are also outlined. The manual is intended to ensure proper disassembly and reassembly of components.
Caterpillar cat el200 b excavator (prefix 6kf) service repair manual (6kf0000...jfskemsemm
This document provides instructions for removing and installing the fuel shutoff solenoid, fuel priming pump, and primary fuel filter on an E200B excavator. The removal procedure involves disconnecting tubes and hoses and removing bolts to access the components. The installation procedure specifies cleaning parts, lubricating with engine oil, and reinstalling components in reverse order of removal while taking care to properly align parts. Tools required include spanner wrenches and lubricant.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...fjjskekfsem
This document provides instructions for removing and installing the fuel transfer pump on an excavator model E240B powered by a 3116 engine. The removal procedure involves holding the spring loaded cover in place and removing bolts to access internal components. Components like the filter screen, seals, fittings and check valves are also removed. The installation procedure is not described but references are provided to check component reusability. Proper containment of fluids is emphasized during maintenance.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...ufjjsjekksemmd
1) The document provides instructions for removing and installing the fuel filter base, fuel priming pump, primary fuel filter, and fuel transfer pump on an E240B excavator.
2) The removal procedures describe disconnecting fuel lines and removing mounting bolts, filters, bases, and other components.
3) The installation procedures describe inspecting parts, lubricating with oil, and reversing the removal steps to mount components with new seals or gaskets if needed. Safety notices are provided throughout.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...fjkskekdmmenm
This document provides instructions for removing and installing the fuel transfer pump on an excavator model E240B powered by a 3116 engine. The removal procedure involves holding the spring loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to avoid contamination.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...uufjdjdkkksmem
1) The document provides instructions for removing and installing the fuel filter base, fuel priming pump, primary fuel filter, and fuel transfer pump on an E240B excavator.
2) The removal procedures describe disconnecting fuel lines and removing mounting bolts, filters, bases, and other components.
3) The installation procedures describe inspecting parts, lubricating with oil, and reversing the removal steps to mount components with new seals or gaskets if needed. Special care is required when installing spring-loaded parts.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...fjsjefskekfmme
This document provides instructions for removing and installing the fuel transfer pump on an excavator model E240B powered by a 3116 engine. The removal procedure involves holding the spring loaded cover in place and removing bolts to access internal components. Components like the filter screen, seals, springs and fittings are then removed. The installation procedure is not described but presumably involves reversing the removal steps. Precautions are provided to contain fluids and prevent contamination.
Caterpillar cat e200 b excavator (prefix 6kf) service repair manual (6kf00001...fjseazqkkdmmem
This service repair manual provides instructions for removing and installing various fuel system components on an E200B excavator powered by a 3116 engine, including:
1. The fuel priming pump and primary fuel filter.
2. The fuel transfer pump.
3. The fuel shutoff solenoid.
Detailed step-by-step procedures are provided with illustrations to guide the technician. Safety and contamination prevention procedures are also outlined. The manual is intended to ensure proper disassembly and reassembly of components.
Caterpillar cat e200 b excavator (prefix 6kf) service repair manual (6kf00001...ufjdfjjkskemme
This service repair manual provides instructions for removing and installing various fuel system components on an E200B excavator powered by a 3116 engine, including:
1. The fuel priming pump and primary fuel filter.
2. The fuel transfer pump.
3. The fuel shutoff solenoid.
Detailed step-by-step procedures are provided with illustrations to guide the technician. Safety and contamination prevention procedures are also outlined. The manual is intended to ensure proper disassembly and reassembly of components.
Caterpillar cat el200 b excavator (prefix 6kf) service repair manual (6kf0000...jfskemsemm
This document provides instructions for removing and installing the fuel shutoff solenoid, fuel priming pump, and primary fuel filter on an E200B excavator. The removal procedure involves disconnecting tubes and hoses and removing bolts to access the components. The installation procedure specifies cleaning parts, lubricating with engine oil, and reinstalling components in reverse order of removal while taking care to properly align parts. Tools required include spanner wrenches and lubricant.
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It includes detailed illustrations and numbered steps for each procedure, and safety warnings regarding working with refrigerants.
The document provides instructions for disassembling and assembling the pilot valve (joystick) of a 322C excavator. It describes in detail how to disassemble the 20 components of the pilot valve, including removing plates, springs, seals, spools and plugs. The assembly section then lists 21 steps to reassemble the pilot valve, replacing all O-rings and seals and ensuring correct installation of springs, spools and other components. The goal is to properly disassemble and reassemble the pilot valve while maintaining cleanliness to prevent issues.
This document provides instructions for removing and installing fuel injection lines and the fuel manifold on a Caterpillar 321D LCR excavator equipped with a C6.4 engine. The removal procedure involves disconnecting harness and tubes, removing clips and bolts, and discarding old fuel lines. The installation procedure specifies installing new fuel lines and tubes using identification marks, torque specifications, and ensuring the fuel system is depressurized before opening it. Precautions are listed to prevent contamination and injury from high pressure fuel.
This document provides instructions for removing and installing fuel system components on a Caterpillar 322C excavator engine. The procedures describe removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid. Detailed illustrations and cautions are provided to complete each step correctly and safely.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes:
1) Detailed step-by-step instructions to remove components like the air conditioner group, actuator motors, control module, and refrigerant receiver-dryer. Each step includes illustrations.
2) Safety warnings to take precautions when working with refrigerant due to the risk of injury from contact or inhalation.
3) Specifications for replacement parts like seals and dimensions for proper installation.
The document provides thorough maintenance instructions for servicing excavator air conditioning systems.
The document provides instructions for removing and installing final drive sprockets, travel brake valves, and travel motors on a 322-A excavator model. Key steps include separating the track assemblies, using tools to support heavy components like the sprocket while removing fasteners, cleaning mating surfaces, replacing seals, and torquing fasteners to the specified values. The process also requires draining oil from the final drive before removing certain components.
1. The document provides instructions for removing and installing fuel injection lines and the fuel manifold on a Caterpillar 321D LCR excavator.
2. To remove the lines and manifold, technicians must disconnect harness assemblies, tubes, and hoses after relieving fuel pressure and marking components.
3. Installation requires connecting new fuel lines and hoses according to illustrated steps while maintaining cleanliness to prevent contamination.
1. The document provides instructions for removing and installing an electronic unit injector, turbocharger, and exhaust manifold on a Caterpillar 321D LCR excavator. It includes diagrams and lists required tools.
2. The procedure for removing an electronic unit injector involves disconnecting harness assemblies and fuel lines, removing mounting bolts and nuts, and using pry bars. Cleanliness is important to prevent dirt entry.
3. Removing the turbocharger requires loosening clamps and removing nuts, tubes, and hoses connecting it to the engine.
4. Removing the exhaust manifold is preceded by removing the turbocharger. Cleanliness of all parts is emphasized during removal and installation.
This document provides instructions for removing and installing the fuel injection pump gear on a Caterpillar C6.4 engine. It describes:
- Using a puller tool to remove the existing gear and key
- Installing the key and securing the new gear with a torque wrench, holding it in a soft jaw vice
- Cleanliness is important to prevent contaminants from causing premature wear
Caterpillar Cat 320C U Excavator (Prefix PAC) Service Repair Manual (PAC00001...fujsked9dikdkd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
1) Removing and installing the flywheel housing.
2) Removing and installing the crankshaft pulley.
3) Removing the crankshaft front seal.
4) Installing a new crankshaft front seal.
5) Removing just the idler gear from the front gear group.
The document contains detailed steps, illustrations, and safety notices for completing each procedure. Required tools are listed for each job.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and filters, checking seals and gaskets, and ensuring parts are clean to prevent contamination. Tools and safety precautions are also listed.
Caterpillar Cat 320C S Excavator (Prefix BBL) Service Repair Manual (BBL00001...fujsked9dikdkd
The document provides installation instructions for auxiliary control valves on an excavator model 320C. It involves 33 steps including installing hoses and fittings, connecting electrical connectors, and tightening bolts. Special tools and safety precautions are noted. The process concludes by installing covers and checking operation.
The document provides instructions for disassembling a swing drive from a 320C excavator. It describes:
1) Removing the retaining ring from the swing drive housing using retaining ring pliers.
2) Using a driver group to remove the bearing from the housing.
3) Removing the inner ring, roller assembly, and outer ring from the bearing.
This document provides instructions for removing and disassembling the water pump on a Caterpillar 320C excavator engine. The key steps include:
1. Draining the coolant and removing the V-belts.
2. Removing four bolts to separate the water pump, pulley, and O-ring from the engine.
3. Heating the water pump to 80°C to make disassembly easier, then removing four bolts and the pulley from the pump housing.
Caterpillar Cat 320C LU 320CLU Excavator (Prefix PAC) Service Repair Manual (...fujsked9dikdkd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
1) Removing and installing the flywheel housing.
2) Removing and installing the crankshaft pulley.
3) Removing the crankshaft front seal.
4) Installing a new crankshaft front seal.
5) Removing just the idler gear from the front gear group.
The document contains detailed steps, illustrations, and safety notices for completing each procedure. Required tools are listed for each job.
Caterpillar Cat 320C L Excavator (Prefix BBL) Service Repair Manual (BBL00001...fujsked9dikdkd
The document provides instructions for installing and assembling auxiliary control valves on an excavator model 320C. It describes 38 steps for installing control valves F1 and F4, including connecting hoses and electrical connections, installing mounting bolts, and filling hydraulic oil. It also describes 12 steps for assembling the F2 auxiliary control valve, including installing O-rings, springs, fittings and plugs on the spool, solenoid valve and housing. The instructions conclude by stating to install the F2 control valve by referring to an installation procedure.
Caterpillar Cat 320C L 320CL Excavator (Prefix SBN) Service Repair Manual (SB...fujsked9dikdkd
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 320C excavator engine. The removal procedure involves using tools to remove the electric starting motor and flywheel/ring gear. Twelve bolts and washers are then removed to detach the adapter from the flywheel housing. For installation, the adapter is reattached with twelve bolts and washers, followed by reinstalling the flywheel/ring gear and electric starting motor.
Caterpillar Cat 320C L 320CL Excavator (Prefix RAW) Service Repair Manual (RA...fujsked9dikdkd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
- Removing and installing the flywheel using various tools to secure and lift it.
- Removing the crankshaft rear seal using a slide hammer puller and distorter ring.
- Installing a new crankshaft rear seal and wear sleeve using an installer, locator, and bolt.
- Removing and installing the flywheel housing which requires lifting equipment and replacing the oil seal if needed.
- Removing the crankshaft pulley using a combination puller and socket.
Caterpillar Cat 320C L 320CL Excavator (Prefix HKT) Service Repair Manual (HK...fujsked9dikdkd
This document provides installation instructions for auxiliary control valves on an excavator model 320C. It involves installing pilot lines and hoses between the auxiliary control valves and connecting them to the main control valve and hydraulic system. The steps include fastening the control valves together, installing mount bolts, connecting pilot lines and hoses, and checking for proper operation and leaks once installation is complete. Proper containment of fluids and cleaning of components is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 320C L 320CL Excavator (Prefix GNG) Service Repair Manual (GN...fujsked9dikdkd
The document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 320C excavator engine. Key steps include:
1. Removing the fuel injection lines, fuel filter base, and clamps securing the nozzles.
2. Using puller tools attached to the nozzle and fuel line connection to carefully extract each nozzle.
3. Cleaning all parts to prevent contamination, then reversing the removal steps to reinstall the nozzles, fuel lines, and other components. Proper cleaning and replacement of parts is emphasized to avoid damaging components and contaminating the fuel system.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It includes detailed illustrations and numbered steps for each procedure, and safety warnings regarding working with refrigerants.
The document provides instructions for disassembling and assembling the pilot valve (joystick) of a 322C excavator. It describes in detail how to disassemble the 20 components of the pilot valve, including removing plates, springs, seals, spools and plugs. The assembly section then lists 21 steps to reassemble the pilot valve, replacing all O-rings and seals and ensuring correct installation of springs, spools and other components. The goal is to properly disassemble and reassemble the pilot valve while maintaining cleanliness to prevent issues.
This document provides instructions for removing and installing fuel injection lines and the fuel manifold on a Caterpillar 321D LCR excavator equipped with a C6.4 engine. The removal procedure involves disconnecting harness and tubes, removing clips and bolts, and discarding old fuel lines. The installation procedure specifies installing new fuel lines and tubes using identification marks, torque specifications, and ensuring the fuel system is depressurized before opening it. Precautions are listed to prevent contamination and injury from high pressure fuel.
This document provides instructions for removing and installing fuel system components on a Caterpillar 322C excavator engine. The procedures describe removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid. Detailed illustrations and cautions are provided to complete each step correctly and safely.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes:
1) Detailed step-by-step instructions to remove components like the air conditioner group, actuator motors, control module, and refrigerant receiver-dryer. Each step includes illustrations.
2) Safety warnings to take precautions when working with refrigerant due to the risk of injury from contact or inhalation.
3) Specifications for replacement parts like seals and dimensions for proper installation.
The document provides thorough maintenance instructions for servicing excavator air conditioning systems.
The document provides instructions for removing and installing final drive sprockets, travel brake valves, and travel motors on a 322-A excavator model. Key steps include separating the track assemblies, using tools to support heavy components like the sprocket while removing fasteners, cleaning mating surfaces, replacing seals, and torquing fasteners to the specified values. The process also requires draining oil from the final drive before removing certain components.
1. The document provides instructions for removing and installing fuel injection lines and the fuel manifold on a Caterpillar 321D LCR excavator.
2. To remove the lines and manifold, technicians must disconnect harness assemblies, tubes, and hoses after relieving fuel pressure and marking components.
3. Installation requires connecting new fuel lines and hoses according to illustrated steps while maintaining cleanliness to prevent contamination.
1. The document provides instructions for removing and installing an electronic unit injector, turbocharger, and exhaust manifold on a Caterpillar 321D LCR excavator. It includes diagrams and lists required tools.
2. The procedure for removing an electronic unit injector involves disconnecting harness assemblies and fuel lines, removing mounting bolts and nuts, and using pry bars. Cleanliness is important to prevent dirt entry.
3. Removing the turbocharger requires loosening clamps and removing nuts, tubes, and hoses connecting it to the engine.
4. Removing the exhaust manifold is preceded by removing the turbocharger. Cleanliness of all parts is emphasized during removal and installation.
This document provides instructions for removing and installing the fuel injection pump gear on a Caterpillar C6.4 engine. It describes:
- Using a puller tool to remove the existing gear and key
- Installing the key and securing the new gear with a torque wrench, holding it in a soft jaw vice
- Cleanliness is important to prevent contaminants from causing premature wear
Caterpillar Cat 320C U Excavator (Prefix PAC) Service Repair Manual (PAC00001...fujsked9dikdkd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
1) Removing and installing the flywheel housing.
2) Removing and installing the crankshaft pulley.
3) Removing the crankshaft front seal.
4) Installing a new crankshaft front seal.
5) Removing just the idler gear from the front gear group.
The document contains detailed steps, illustrations, and safety notices for completing each procedure. Required tools are listed for each job.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and filters, checking seals and gaskets, and ensuring parts are clean to prevent contamination. Tools and safety precautions are also listed.
Caterpillar Cat 320C S Excavator (Prefix BBL) Service Repair Manual (BBL00001...fujsked9dikdkd
The document provides installation instructions for auxiliary control valves on an excavator model 320C. It involves 33 steps including installing hoses and fittings, connecting electrical connectors, and tightening bolts. Special tools and safety precautions are noted. The process concludes by installing covers and checking operation.
The document provides instructions for disassembling a swing drive from a 320C excavator. It describes:
1) Removing the retaining ring from the swing drive housing using retaining ring pliers.
2) Using a driver group to remove the bearing from the housing.
3) Removing the inner ring, roller assembly, and outer ring from the bearing.
This document provides instructions for removing and disassembling the water pump on a Caterpillar 320C excavator engine. The key steps include:
1. Draining the coolant and removing the V-belts.
2. Removing four bolts to separate the water pump, pulley, and O-ring from the engine.
3. Heating the water pump to 80°C to make disassembly easier, then removing four bolts and the pulley from the pump housing.
Caterpillar Cat 320C LU 320CLU Excavator (Prefix PAC) Service Repair Manual (...fujsked9dikdkd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
1) Removing and installing the flywheel housing.
2) Removing and installing the crankshaft pulley.
3) Removing the crankshaft front seal.
4) Installing a new crankshaft front seal.
5) Removing just the idler gear from the front gear group.
The document contains detailed steps, illustrations, and safety notices for completing each procedure. Required tools are listed for each job.
Caterpillar Cat 320C L Excavator (Prefix BBL) Service Repair Manual (BBL00001...fujsked9dikdkd
The document provides instructions for installing and assembling auxiliary control valves on an excavator model 320C. It describes 38 steps for installing control valves F1 and F4, including connecting hoses and electrical connections, installing mounting bolts, and filling hydraulic oil. It also describes 12 steps for assembling the F2 auxiliary control valve, including installing O-rings, springs, fittings and plugs on the spool, solenoid valve and housing. The instructions conclude by stating to install the F2 control valve by referring to an installation procedure.
Caterpillar Cat 320C L 320CL Excavator (Prefix SBN) Service Repair Manual (SB...fujsked9dikdkd
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 320C excavator engine. The removal procedure involves using tools to remove the electric starting motor and flywheel/ring gear. Twelve bolts and washers are then removed to detach the adapter from the flywheel housing. For installation, the adapter is reattached with twelve bolts and washers, followed by reinstalling the flywheel/ring gear and electric starting motor.
Caterpillar Cat 320C L 320CL Excavator (Prefix RAW) Service Repair Manual (RA...fujsked9dikdkd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
- Removing and installing the flywheel using various tools to secure and lift it.
- Removing the crankshaft rear seal using a slide hammer puller and distorter ring.
- Installing a new crankshaft rear seal and wear sleeve using an installer, locator, and bolt.
- Removing and installing the flywheel housing which requires lifting equipment and replacing the oil seal if needed.
- Removing the crankshaft pulley using a combination puller and socket.
Caterpillar Cat 320C L 320CL Excavator (Prefix HKT) Service Repair Manual (HK...fujsked9dikdkd
This document provides installation instructions for auxiliary control valves on an excavator model 320C. It involves installing pilot lines and hoses between the auxiliary control valves and connecting them to the main control valve and hydraulic system. The steps include fastening the control valves together, installing mount bolts, connecting pilot lines and hoses, and checking for proper operation and leaks once installation is complete. Proper containment of fluids and cleaning of components is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 320C L 320CL Excavator (Prefix GNG) Service Repair Manual (GN...fujsked9dikdkd
The document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 320C excavator engine. Key steps include:
1. Removing the fuel injection lines, fuel filter base, and clamps securing the nozzles.
2. Using puller tools attached to the nozzle and fuel line connection to carefully extract each nozzle.
3. Cleaning all parts to prevent contamination, then reversing the removal steps to reinstall the nozzles, fuel lines, and other components. Proper cleaning and replacement of parts is emphasized to avoid damaging components and contaminating the fuel system.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: E240B EXCAVATOR 8SF
Configuration: E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928280
Fuel Filter Base - Remove and Install
SMCS - 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Start By:
a. Remove the crankcase breather. Refer to Disassembly and Assembly, "Crankcase Breather -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00629777
Typical example
1. Use Tooling (A) to remove fuel filter (5).
2. Disconnect tube assemblies (1) and (2) from fuel filter base (4).
3. Remove bolts (3) from fuel filter base (4).
4. Remove fuel filter base (4) and the gasket from the engine.
2/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g00629788
5. Remove fuel pressure relief valve (7) from fuel filter base (4), if necessary.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 3 g00629788
1. Install fuel pressure relief valve (7) on fuel filter base (4).
Illustration 4 g00629777
Typical example
2. Inspect the condition of the gasket. Replace the gasket, if necessary.
3. Position the gasket and fuel filter base (4) on the engine.
4. Install bolts (3) that secure fuel filter base (4) on the engine.
5. Connect tube assemblies (1) and (2) to fuel filter base (4).
4/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. 6. Use Tooling (A) to install fuel filter (5).
7. Install O-ring seal (6) on fuel filter base (4).
End By:
a. Install the crankcase breather. Refer to Disassembly and Assembly, "Crankcase Breather -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 9 12:02:29 UTC+0800 2019
5/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: E240B EXCAVATOR 8SF
Configuration: E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928293
Fuel Priming Pump and Primary Fuel Filter - Remove and
Install
SMCS - 1258-010; 1260-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 1 g00678475
1. Disconnect tube assembly (2) from primary fuel filter base (1).
Illustration 2 g00678476
2. Remove bolts (4) from the fuel priming pump (3).
3. Remove fuel priming pump (3) from the primary fuel filter base.
Illustration 3 g00678479
4. Remove bolt (5) from the primary fuel filter base.
2/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. 5. Remove filter element (6) and housing (7) from the primary fuel filter base.
Illustration 4 g00773124
6. Remove bolts (8) from the primary fuel filter base (1).
7. Remove primary fuel filter base (1) from the engine.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 5 g00773124
1. Install bolts (8) that secure primary fuel filter base (1) to the engine.
Illustration 6 g00678479
2. Install filter element (6) and housing (7) to the primary filter base with bolt (5).
Illustration 7 g00678476
4/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. 3. Install bolts (4) that secure fuel priming pump (3) to the primary fuel filter base.
Illustration 8 g00678475
4. Connect tube assembly (2) to primary fuel filter base (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 9 12:03:16 UTC+0800 2019
5/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: E240B EXCAVATOR 8SF
Configuration: E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928670
Fuel Transfer Pump - Remove
SMCS - 1256-011
Removal Procedure
Note: The governor and the fuel transfer pump have been removed from the engine for
photographic purposes only. This procedure may be done with the governor on the engine.
Illustration 1 g00623633
1/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 2 g00623671
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
1. Hold cover (1) in place and remove bolts (2) in order to release the spring beneath cover (1).
Remove cover (1).
2/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 3 g00623686
2. Remove fitting (3) and the check valve from cover (1). Remove the filter screen (if
equipped) from fitting (3).
Illustration 4 g00623687
3. Remove spring (4) and piston (5).
4. Remove upper O-ring seal (6).
Illustration 5 g00623714
3/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. 5. Remove sleeve assembly (7). Inspect the face of lifter (8) for excessive wear. Inspect the
surface of the camshaft that is inside of the governor for excessive wear or damage.
6. Remove lower O-ring seal (9).
Illustration 6 g00623719
7. Remove fitting (10) and the check valve.
Note: For information on reusability of the components in the fuel transfer pump, refer to
Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 9 12:04:04 UTC+0800 2019
4/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: E240B EXCAVATOR 8SF
Configuration: E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928343
Fuel Transfer Pump - Install
SMCS - 1256-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-2998 Lubricant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of the components in the fuel transfer pump, refer to
Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
1/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 1 g00623719
1. Lubricate fitting (10) and the bore with clean engine oil. Install the check valve and fitting
(10).
Illustration 2 g00623714
2. Inspect the condition of the O-ring seal. Replace the O-ring seal, if necessary. Install lower
O-ring seal (9).
3. Apply Tooling (A) on the face of lifter (8). Install sleeve assembly (7). Ensure that the flat
on the sleeve aligns with the flat in the bore of the housing.
Illustration 3 g00623687
2/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 4. Lubricate piston (5) with clean engine oil. Install piston (5) and spring (4).
Illustration 4 g00623686
5. Lubricate fitting (3) and the bore for the check valve with clean engine oil. Install the check
valve with the sealing face toward the fitting.
6. Install the O-ring seal and fitting (3).
Illustration 5 g00623671
3/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 6 g00623633
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
7. Place cover (1) over spring (4). Install bolts (2) in order to compress spring (4).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 9 12:04:51 UTC+0800 2019
4/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: E240B EXCAVATOR 8SF
Configuration: E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928366
Fuel Shutoff Solenoid - Remove and Install
SMCS - 1259-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-5120 Spanner Wrench(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00585831
1. Disconnect the harness assembly (2) from fuel shutoff solenoid (1).
2. Use Tooling (A) to remove the fuel shutoff solenoid from the governor.
3. Remove the O-ring seal from the shutoff solenoid .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-5120 Spanner Wrench(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
2/3
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 2 g00585831
1. Inspect the O-ring seal on the fuel shutoff solenoid. If the O-ring seal is worn or damaged,
use new parts for replacement.
2. Install the O-ring seal on the fuel shutoff solenoid.
3. Install the fuel shutoff solenoid in the governor. Use Tooling (A) and a suitable torque
wrench to tighten the fuel shutoff solenoid to the following torque 30 ± 5 N·m (22 ± 4 lb ft).
4. Connect the harness assembly to the fuel shutoff solenoid.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 9 12:05:39 UTC+0800 2019
3/3
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: E240B EXCAVATOR 8SF
Configuration: E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928381
Governor - Remove
SMCS - 1264-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
Start By:
a. Remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 1 g00613041
1. Disconnect the governor control cable.
2. Remove oil tube assembly (1). Remove tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
Illustration 2 g00613071
3. Remove clip (4).
2/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 3 g00655975
4. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
Illustration 4 g00613149
5. Remove the clip and use Tooling (A) to remove the clevis pin (6).
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
3/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 5 g00613563
6. Remove bolts (7) and the washers that hold the governor in position.
Illustration 6 g00673182
7. Remove the governor from the engine.
Illustration 7 g00673180
8. Remove O-ring seal (3) on the governor.
Illustration 8 g00672742
4/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. 9. Remove the O-ring seal and tube assembly (5) from the cylinder head.
Illustration 9 g00672733
10. Remove O-ring seal (2) on the tube assembly (5).
Illustration 10 g00673178
11. Remove O-ring seal (1) from the cylinder head.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 9 12:06:27 UTC+0800 2019
5/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...