This document provides instructions for removing and installing the fuel transfer pump on an excavator. The removal procedure involves holding the spring-loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to prevent contamination.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...fjjskekfsem
This document provides instructions for removing and installing the fuel transfer pump on an excavator model E240B powered by a 3116 engine. The removal procedure involves holding the spring loaded cover in place and removing bolts to access internal components. Components like the filter screen, seals, fittings and check valves are also removed. The installation procedure is not described but references are provided to check component reusability. Proper containment of fluids is emphasized during maintenance.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...ufjjsjekksemmd
1) The document provides instructions for removing and installing the fuel filter base, fuel priming pump, primary fuel filter, and fuel transfer pump on an E240B excavator.
2) The removal procedures describe disconnecting fuel lines and removing mounting bolts, filters, bases, and other components.
3) The installation procedures describe inspecting parts, lubricating with oil, and reversing the removal steps to mount components with new seals or gaskets if needed. Safety notices are provided throughout.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...fjkskekdmmenm
This document provides instructions for removing and installing the fuel transfer pump on an excavator model E240B powered by a 3116 engine. The removal procedure involves holding the spring loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to avoid contamination.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...uufjdjdkkksmem
1) The document provides instructions for removing and installing the fuel filter base, fuel priming pump, primary fuel filter, and fuel transfer pump on an E240B excavator.
2) The removal procedures describe disconnecting fuel lines and removing mounting bolts, filters, bases, and other components.
3) The installation procedures describe inspecting parts, lubricating with oil, and reversing the removal steps to mount components with new seals or gaskets if needed. Special care is required when installing spring-loaded parts.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...fjsjefskekfmme
This document provides instructions for removing and installing the fuel transfer pump on an excavator model E240B powered by a 3116 engine. The removal procedure involves holding the spring loaded cover in place and removing bolts to access internal components. Components like the filter screen, seals, springs and fittings are then removed. The installation procedure is not described but presumably involves reversing the removal steps. Precautions are provided to contain fluids and prevent contamination.
Caterpillar cat e200 b excavator (prefix 6kf) service repair manual (6kf00001...fjseazqkkdmmem
This service repair manual provides instructions for removing and installing various fuel system components on an E200B excavator powered by a 3116 engine, including:
1. The fuel priming pump and primary fuel filter.
2. The fuel transfer pump.
3. The fuel shutoff solenoid.
Detailed step-by-step procedures are provided with illustrations to guide the technician. Safety and contamination prevention procedures are also outlined. The manual is intended to ensure proper disassembly and reassembly of components.
Caterpillar cat e200 b excavator (prefix 6kf) service repair manual (6kf00001...ufjdfjjkskemme
This service repair manual provides instructions for removing and installing various fuel system components on an E200B excavator powered by a 3116 engine, including:
1. The fuel priming pump and primary fuel filter.
2. The fuel transfer pump.
3. The fuel shutoff solenoid.
Detailed step-by-step procedures are provided with illustrations to guide the technician. Safety and contamination prevention procedures are also outlined. The manual is intended to ensure proper disassembly and reassembly of components.
Caterpillar cat el200 b excavator (prefix 6kf) service repair manual (6kf0000...jfskemsemm
This document provides instructions for removing and installing the fuel shutoff solenoid, fuel priming pump, and primary fuel filter on an E200B excavator. The removal procedure involves disconnecting tubes and hoses and removing bolts to access the components. The installation procedure specifies cleaning parts, lubricating with engine oil, and reinstalling components in reverse order of removal while taking care to properly align parts. Tools required include spanner wrenches and lubricant.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...fjjskekfsem
This document provides instructions for removing and installing the fuel transfer pump on an excavator model E240B powered by a 3116 engine. The removal procedure involves holding the spring loaded cover in place and removing bolts to access internal components. Components like the filter screen, seals, fittings and check valves are also removed. The installation procedure is not described but references are provided to check component reusability. Proper containment of fluids is emphasized during maintenance.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...ufjjsjekksemmd
1) The document provides instructions for removing and installing the fuel filter base, fuel priming pump, primary fuel filter, and fuel transfer pump on an E240B excavator.
2) The removal procedures describe disconnecting fuel lines and removing mounting bolts, filters, bases, and other components.
3) The installation procedures describe inspecting parts, lubricating with oil, and reversing the removal steps to mount components with new seals or gaskets if needed. Safety notices are provided throughout.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...fjkskekdmmenm
This document provides instructions for removing and installing the fuel transfer pump on an excavator model E240B powered by a 3116 engine. The removal procedure involves holding the spring loaded cover in place and removing bolts to access internal components like the spring, piston, seals and fittings. The installation procedure specifies cleaning and inspecting components before reassembling them in reverse order. Proper containment of fluids is emphasized to avoid contamination.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...uufjdjdkkksmem
1) The document provides instructions for removing and installing the fuel filter base, fuel priming pump, primary fuel filter, and fuel transfer pump on an E240B excavator.
2) The removal procedures describe disconnecting fuel lines and removing mounting bolts, filters, bases, and other components.
3) The installation procedures describe inspecting parts, lubricating with oil, and reversing the removal steps to mount components with new seals or gaskets if needed. Special care is required when installing spring-loaded parts.
Caterpillar cat e240 b excavator (prefix 8sf) service repair manual (8sf00001...fjsjefskekfmme
This document provides instructions for removing and installing the fuel transfer pump on an excavator model E240B powered by a 3116 engine. The removal procedure involves holding the spring loaded cover in place and removing bolts to access internal components. Components like the filter screen, seals, springs and fittings are then removed. The installation procedure is not described but presumably involves reversing the removal steps. Precautions are provided to contain fluids and prevent contamination.
Caterpillar cat e200 b excavator (prefix 6kf) service repair manual (6kf00001...fjseazqkkdmmem
This service repair manual provides instructions for removing and installing various fuel system components on an E200B excavator powered by a 3116 engine, including:
1. The fuel priming pump and primary fuel filter.
2. The fuel transfer pump.
3. The fuel shutoff solenoid.
Detailed step-by-step procedures are provided with illustrations to guide the technician. Safety and contamination prevention procedures are also outlined. The manual is intended to ensure proper disassembly and reassembly of components.
Caterpillar cat e200 b excavator (prefix 6kf) service repair manual (6kf00001...ufjdfjjkskemme
This service repair manual provides instructions for removing and installing various fuel system components on an E200B excavator powered by a 3116 engine, including:
1. The fuel priming pump and primary fuel filter.
2. The fuel transfer pump.
3. The fuel shutoff solenoid.
Detailed step-by-step procedures are provided with illustrations to guide the technician. Safety and contamination prevention procedures are also outlined. The manual is intended to ensure proper disassembly and reassembly of components.
Caterpillar cat el200 b excavator (prefix 6kf) service repair manual (6kf0000...jfskemsemm
This document provides instructions for removing and installing the fuel shutoff solenoid, fuel priming pump, and primary fuel filter on an E200B excavator. The removal procedure involves disconnecting tubes and hoses and removing bolts to access the components. The installation procedure specifies cleaning parts, lubricating with engine oil, and reinstalling components in reverse order of removal while taking care to properly align parts. Tools required include spanner wrenches and lubricant.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 422E backhoe loader with a 3054C engine, including the fuel priming pump, fuel filter base, fuel injection lines, fuel injection nozzles, and fuel injection pump. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components in the reverse order. Cautions are provided regarding containing fluids and preventing contamination. Required tools are listed for each job.
Caterpillar Cat E70 EXCAVATOR (Prefix 3BG) Service Repair Manual (3BG00001-UP...ufjskmdmdmed
This document provides instructions for properly installing Duo-Cone seals. It describes the components of Duo-Cone seals and outlines best practices for cleaning, handling, inspecting, and assembling the seals using the appropriate tooling. Critical areas like the seal ring face and housing ramp are to be carefully inspected for defects before installation to prevent leaks. Rubber seals and metal components must be kept free of contamination and lubricated during assembly.
This document provides instructions for removing and installing a radiator on a Caterpillar 906 Compact Wheel Loader. The removal procedure involves:
1. Draining the coolant and removing the radiator fill cap.
2. Removing mounting bolts and brackets to detach the radiator.
3. Using straps to lift out the radiator.
The installation procedure describes reinstalling the radiator using new gaskets and bolts, then refilling the cooling system. Safety precautions are provided to avoid burns from hot coolant and ensure fluids are contained.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be applied where noted. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides instructions for assembling a Type I governor used on 3114, 3116, and 3126 engines. It describes 19 steps to assemble components like the drive gear, C spring, fuel ratio control lever, output servo, bearing block, and torque cam. Tools required include a governor repair fixture, clevis driver, servo block, pin punch, and torque adjusting tool. Proper positioning and clearance of parts is important for correct governor function.
This document provides instructions for disassembling and assembling starting motors for Caterpillar track loaders and excavators. It describes the parts and tools needed and steps to disassemble three starting motor models: 42-MT, 37-MT, and 41-MT. The instructions cover removing components like the rear housing, brushes, pinion drive, shift lever housing, and field winding coil. Cleaning and inspection steps are also included. The goal is to repair or replace worn parts to restore the starting motors to working condition.
The document provides instructions for removing and installing the lift cylinder and lift arms on a Caterpillar 420E backhoe loader. It includes:
- A list of required tools for each job.
- Step-by-step procedures to release hydraulic pressure, remove hoses and pins, and use tools to detach the lift cylinder and lift arms.
- Notes on cleaning parts and inspecting for wear before reassembly.
- An installation procedure that reverses the removal steps and includes torquing specifications.
The document provides instructions for removing and installing a tie rod on the front steering of a 420D backhoe loader. It lists the required tool as a transmission repair stand and instructs the user to first remove the front axle from the machine. Safety precautions are provided to release hydraulic pressure before servicing. Detailed steps are then outlined to remove the tie rod from the axle and install a new one.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...ufjskmdmdmed
The document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It includes the following procedures:
1. Removing the crankshaft vibration damper and pulley.
2. Removing and installing the crankshaft front seal.
3. Removing and installing the front cover.
4. Removing the front housing by taking off the front engine support, belt tightener, and front housing.
The document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It includes the following procedures:
1. Removing the crankshaft vibration damper and pulley.
2. Removing and installing the crankshaft front seal.
3. Removing and installing the front cover.
4. Removing the front housing by taking off the front engine support, belt tightener, and front housing.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a 527 Track Skidder with a 3304 engine. The procedures include removing bolts and hoses, checking gaskets, applying fuel to seals during installation, and ensuring parts are clean to prevent contamination. Illustrations show the component locations and part numbers.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It involves 20 steps including installing bearings, pins, bolts and other components onto the swing frame assembly and attaching hydraulic hoses and electrical harnesses. Tools required include a driver, lever puller, and bearing installer. Precautions are provided for safely releasing hydraulic pressure before removing any components.
This document provides instructions to disassemble a bank valve on a 420E Backhoe Loader. The 19 step procedure includes removing manifolds, valves, spools, cartridges, seals, springs and covers. Special care must be taken when removing parts under spring pressure to avoid injury.
This document provides instructions for disassembling and assembling the steering metering pump on a 428D Backhoe Loader. The removal procedure involves removing covers, plates, bolts and nuts to access the steering column. Disassembly involves removing an end cap, seals, housing components, drive components, springs and fittings. Assembly is the reverse of disassembly, applying new seals and lubricating components before installation. Cleanliness is important during disassembly and assembly to prevent contaminating the hydraulic system.
The document provides instructions for disassembling the transmission of a 428D backhoe loader in 3 steps:
1. Remove the transmission and drain the oil.
2. Disassemble the transmission into its major components like the case, output shafts, and gears.
3. Further disassemble the components using various tools, removing items like bearings, seals, springs, and shafts. Detailed illustrations are provided to identify specific parts.
The document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It describes procedures for removing and installing fuel injection lines, nozzles, and the governor/camshaft. Removal involves draining fuel, removing retaining components, and plugging lines. Installation requires cleaning, adding new seals, and reinstalling components in reverse order of removal while torquing fasteners to specified values. Disassembly of the governor/camshaft involves using tools to separate the sleeve, retaining ring, and bearing from the camshaft.
The document provides instructions for removing and installing various components of a Caterpillar C2.4 Tier 4 Final engine, including:
- Removing and installing the fuel manifold by removing bolts and disconnecting fuel injection lines.
- Removing and installing fuel injection lines by disconnecting hoses and removing clamps and bolts.
- Removing and installing the turbocharger by removing intake hoses and disconnecting pipes.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions, then describes 7 steps to disconnect hoses and cables, attach lifting tools, and remove mounting bolts to lift the 45 kg piston pump out of the machine. Personal injury can result from hydraulic pressure, so pressure must be released before removal.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 422E backhoe loader with a 3054C engine, including the fuel priming pump, fuel filter base, fuel injection lines, fuel injection nozzles, and fuel injection pump. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components in the reverse order. Cautions are provided regarding containing fluids and preventing contamination. Required tools are listed for each job.
Caterpillar Cat E70 EXCAVATOR (Prefix 3BG) Service Repair Manual (3BG00001-UP...ufjskmdmdmed
This document provides instructions for properly installing Duo-Cone seals. It describes the components of Duo-Cone seals and outlines best practices for cleaning, handling, inspecting, and assembling the seals using the appropriate tooling. Critical areas like the seal ring face and housing ramp are to be carefully inspected for defects before installation to prevent leaks. Rubber seals and metal components must be kept free of contamination and lubricated during assembly.
This document provides instructions for removing and installing a radiator on a Caterpillar 906 Compact Wheel Loader. The removal procedure involves:
1. Draining the coolant and removing the radiator fill cap.
2. Removing mounting bolts and brackets to detach the radiator.
3. Using straps to lift out the radiator.
The installation procedure describes reinstalling the radiator using new gaskets and bolts, then refilling the cooling system. Safety precautions are provided to avoid burns from hot coolant and ensure fluids are contained.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be applied where noted. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides instructions for assembling a Type I governor used on 3114, 3116, and 3126 engines. It describes 19 steps to assemble components like the drive gear, C spring, fuel ratio control lever, output servo, bearing block, and torque cam. Tools required include a governor repair fixture, clevis driver, servo block, pin punch, and torque adjusting tool. Proper positioning and clearance of parts is important for correct governor function.
This document provides instructions for disassembling and assembling starting motors for Caterpillar track loaders and excavators. It describes the parts and tools needed and steps to disassemble three starting motor models: 42-MT, 37-MT, and 41-MT. The instructions cover removing components like the rear housing, brushes, pinion drive, shift lever housing, and field winding coil. Cleaning and inspection steps are also included. The goal is to repair or replace worn parts to restore the starting motors to working condition.
The document provides instructions for removing and installing the lift cylinder and lift arms on a Caterpillar 420E backhoe loader. It includes:
- A list of required tools for each job.
- Step-by-step procedures to release hydraulic pressure, remove hoses and pins, and use tools to detach the lift cylinder and lift arms.
- Notes on cleaning parts and inspecting for wear before reassembly.
- An installation procedure that reverses the removal steps and includes torquing specifications.
The document provides instructions for removing and installing a tie rod on the front steering of a 420D backhoe loader. It lists the required tool as a transmission repair stand and instructs the user to first remove the front axle from the machine. Safety precautions are provided to release hydraulic pressure before servicing. Detailed steps are then outlined to remove the tie rod from the axle and install a new one.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...ufjskmdmdmed
The document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It includes the following procedures:
1. Removing the crankshaft vibration damper and pulley.
2. Removing and installing the crankshaft front seal.
3. Removing and installing the front cover.
4. Removing the front housing by taking off the front engine support, belt tightener, and front housing.
The document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It includes the following procedures:
1. Removing the crankshaft vibration damper and pulley.
2. Removing and installing the crankshaft front seal.
3. Removing and installing the front cover.
4. Removing the front housing by taking off the front engine support, belt tightener, and front housing.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a 527 Track Skidder with a 3304 engine. The procedures include removing bolts and hoses, checking gaskets, applying fuel to seals during installation, and ensuring parts are clean to prevent contamination. Illustrations show the component locations and part numbers.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It involves 20 steps including installing bearings, pins, bolts and other components onto the swing frame assembly and attaching hydraulic hoses and electrical harnesses. Tools required include a driver, lever puller, and bearing installer. Precautions are provided for safely releasing hydraulic pressure before removing any components.
This document provides instructions to disassemble a bank valve on a 420E Backhoe Loader. The 19 step procedure includes removing manifolds, valves, spools, cartridges, seals, springs and covers. Special care must be taken when removing parts under spring pressure to avoid injury.
This document provides instructions for disassembling and assembling the steering metering pump on a 428D Backhoe Loader. The removal procedure involves removing covers, plates, bolts and nuts to access the steering column. Disassembly involves removing an end cap, seals, housing components, drive components, springs and fittings. Assembly is the reverse of disassembly, applying new seals and lubricating components before installation. Cleanliness is important during disassembly and assembly to prevent contaminating the hydraulic system.
The document provides instructions for disassembling the transmission of a 428D backhoe loader in 3 steps:
1. Remove the transmission and drain the oil.
2. Disassemble the transmission into its major components like the case, output shafts, and gears.
3. Further disassemble the components using various tools, removing items like bearings, seals, springs, and shafts. Detailed illustrations are provided to identify specific parts.
The document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It describes procedures for removing and installing fuel injection lines, nozzles, and the governor/camshaft. Removal involves draining fuel, removing retaining components, and plugging lines. Installation requires cleaning, adding new seals, and reinstalling components in reverse order of removal while torquing fasteners to specified values. Disassembly of the governor/camshaft involves using tools to separate the sleeve, retaining ring, and bearing from the camshaft.
The document provides instructions for removing and installing various components of a Caterpillar C2.4 Tier 4 Final engine, including:
- Removing and installing the fuel manifold by removing bolts and disconnecting fuel injection lines.
- Removing and installing fuel injection lines by disconnecting hoses and removing clamps and bolts.
- Removing and installing the turbocharger by removing intake hoses and disconnecting pipes.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions, then describes 7 steps to disconnect hoses and cables, attach lifting tools, and remove mounting bolts to lift the 45 kg piston pump out of the machine. Personal injury can result from hydraulic pressure, so pressure must be released before removal.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: E240B EXCAVATOR 8SF
Configuration: E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928280
Fuel Filter Base - Remove and Install
SMCS - 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Start By:
a. Remove the crankcase breather. Refer to Disassembly and Assembly, "Crankcase Breather -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00629777
Typical example
1. Use Tooling (A) to remove fuel filter (5).
2. Disconnect tube assemblies (1) and (2) from fuel filter base (4).
3. Remove bolts (3) from fuel filter base (4).
4. Remove fuel filter base (4) and the gasket from the engine.
2/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g00629788
5. Remove fuel pressure relief valve (7) from fuel filter base (4), if necessary.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 3 g00629788
1. Install fuel pressure relief valve (7) on fuel filter base (4).
Illustration 4 g00629777
Typical example
2. Inspect the condition of the gasket. Replace the gasket, if necessary.
3. Position the gasket and fuel filter base (4) on the engine.
4. Install bolts (3) that secure fuel filter base (4) on the engine.
5. Connect tube assemblies (1) and (2) to fuel filter base (4).
4/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. 6. Use Tooling (A) to install fuel filter (5).
7. Install O-ring seal (6) on fuel filter base (4).
End By:
a. Install the crankcase breather. Refer to Disassembly and Assembly, "Crankcase Breather -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 9 12:02:29 UTC+0800 2019
5/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: E240B EXCAVATOR 8SF
Configuration: E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928293
Fuel Priming Pump and Primary Fuel Filter - Remove and
Install
SMCS - 1258-010; 1260-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 1 g00678475
1. Disconnect tube assembly (2) from primary fuel filter base (1).
Illustration 2 g00678476
2. Remove bolts (4) from the fuel priming pump (3).
3. Remove fuel priming pump (3) from the primary fuel filter base.
Illustration 3 g00678479
4. Remove bolt (5) from the primary fuel filter base.
2/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. 5. Remove filter element (6) and housing (7) from the primary fuel filter base.
Illustration 4 g00773124
6. Remove bolts (8) from the primary fuel filter base (1).
7. Remove primary fuel filter base (1) from the engine.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 5 g00773124
1. Install bolts (8) that secure primary fuel filter base (1) to the engine.
Illustration 6 g00678479
2. Install filter element (6) and housing (7) to the primary filter base with bolt (5).
Illustration 7 g00678476
4/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. 3. Install bolts (4) that secure fuel priming pump (3) to the primary fuel filter base.
Illustration 8 g00678475
4. Connect tube assembly (2) to primary fuel filter base (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 9 12:03:16 UTC+0800 2019
5/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: E240B EXCAVATOR 8SF
Configuration: E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928670
Fuel Transfer Pump - Remove
SMCS - 1256-011
Removal Procedure
Note: The governor and the fuel transfer pump have been removed from the engine for
photographic purposes only. This procedure may be done with the governor on the engine.
Illustration 1 g00623633
1/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 2 g00623671
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
1. Hold cover (1) in place and remove bolts (2) in order to release the spring beneath cover (1).
Remove cover (1).
2/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 3 g00623686
2. Remove fitting (3) and the check valve from cover (1). Remove the filter screen (if
equipped) from fitting (3).
Illustration 4 g00623687
3. Remove spring (4) and piston (5).
4. Remove upper O-ring seal (6).
Illustration 5 g00623714
3/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. 5. Remove sleeve assembly (7). Inspect the face of lifter (8) for excessive wear. Inspect the
surface of the camshaft that is inside of the governor for excessive wear or damage.
6. Remove lower O-ring seal (9).
Illustration 6 g00623719
7. Remove fitting (10) and the check valve.
Note: For information on reusability of the components in the fuel transfer pump, refer to
Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 9 12:04:04 UTC+0800 2019
4/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: E240B EXCAVATOR 8SF
Configuration: E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928343
Fuel Transfer Pump - Install
SMCS - 1256-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-2998 Lubricant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of the components in the fuel transfer pump, refer to
Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
1/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 1 g00623719
1. Lubricate fitting (10) and the bore with clean engine oil. Install the check valve and fitting
(10).
Illustration 2 g00623714
2. Inspect the condition of the O-ring seal. Replace the O-ring seal, if necessary. Install lower
O-ring seal (9).
3. Apply Tooling (A) on the face of lifter (8). Install sleeve assembly (7). Ensure that the flat
on the sleeve aligns with the flat in the bore of the housing.
Illustration 3 g00623687
2/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 4. Lubricate piston (5) with clean engine oil. Install piston (5) and spring (4).
Illustration 4 g00623686
5. Lubricate fitting (3) and the bore for the check valve with clean engine oil. Install the check
valve with the sealing face toward the fitting.
6. Install the O-ring seal and fitting (3).
Illustration 5 g00623671
3/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 6 g00623633
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
7. Place cover (1) over spring (4). Install bolts (2) in order to compress spring (4).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 9 12:04:51 UTC+0800 2019
4/4
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: E240B EXCAVATOR 8SF
Configuration: E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928366
Fuel Shutoff Solenoid - Remove and Install
SMCS - 1259-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-5120 Spanner Wrench(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00585831
1. Disconnect the harness assembly (2) from fuel shutoff solenoid (1).
2. Use Tooling (A) to remove the fuel shutoff solenoid from the governor.
3. Remove the O-ring seal from the shutoff solenoid .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-5120 Spanner Wrench(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
2/3
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 2 g00585831
1. Inspect the O-ring seal on the fuel shutoff solenoid. If the O-ring seal is worn or damaged,
use new parts for replacement.
2. Install the O-ring seal on the fuel shutoff solenoid.
3. Install the fuel shutoff solenoid in the governor. Use Tooling (A) and a suitable torque
wrench to tighten the fuel shutoff solenoid to the following torque 30 ± 5 N·m (22 ± 4 lb ft).
4. Connect the harness assembly to the fuel shutoff solenoid.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 9 12:05:39 UTC+0800 2019
3/3
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: E240B EXCAVATOR 8SF
Configuration: E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928381
Governor - Remove
SMCS - 1264-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
Start By:
a. Remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 1 g00613041
1. Disconnect the governor control cable.
2. Remove oil tube assembly (1). Remove tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
Illustration 2 g00613071
3. Remove clip (4).
2/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 3 g00655975
4. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
Illustration 4 g00613149
5. Remove the clip and use Tooling (A) to remove the clevis pin (6).
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
3/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 5 g00613563
6. Remove bolts (7) and the washers that hold the governor in position.
Illustration 6 g00673182
7. Remove the governor from the engine.
Illustration 7 g00673180
8. Remove O-ring seal (3) on the governor.
Illustration 8 g00672742
4/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. 9. Remove the O-ring seal and tube assembly (5) from the cylinder head.
Illustration 9 g00672733
10. Remove O-ring seal (2) on the tube assembly (5).
Illustration 10 g00673178
11. Remove O-ring seal (1) from the cylinder head.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 9 12:06:27 UTC+0800 2019
5/5
E240B, EL240B TRACK-TYPE EXCAVATORS 8SF00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...