This document provides instructions for removing and installing the front housing of a C27 Industrial Engine. The removal procedure involves detaching various components from the front of the engine like the water pump, oil filter housing, and brackets. Tools are required to remove some parts. The installation procedure specifies applying sealant, positioning the front housing and gasket, and installing bolts and other parts in the reverse order of removal. Tightening torques are provided for the bolts.
This document provides instructions for removing and installing various components of a C27 Industrial Engine, including:
1. Removing the front gear group by removing bolts and gear assemblies.
2. Removing the front housing by removing covers, dampers, brackets, and bolts to detach the housing.
3. Removing the rear housing by removing elbow assemblies, bolts connecting the oil pan, and disconnecting hose assemblies.
The document provides instructions for removing and installing the front housing on a C27 Industrial Engine. It describes removing covers, brackets, bolts, and the front housing itself. Tools needed are listed. Removal involves disconnecting hoses and electrical connections. Installation specifies applying sealant, installing gaskets and components in reverse order of removal, and tightening bolts to the specified torques.
This document provides installation and removal instructions for various components of a C27 Locomotive Engine, including:
- Instructions for removing and installing the front housing, which includes removing covers, brackets, bolts and the housing itself.
- Procedures for removing and installing the front gear group, which involves removing shafts, bushings, plates and gears.
- Steps for removing the rear housing, such as disconnecting hoses, removing bolts, and lifting off the housing.
The document provides detailed illustrations and numbered steps for each procedure, and lists any required tools. Safety and cleaning notes are included to handle fluids and prevent contamination.
This document provides installation and removal instructions for various components of a C27 Locomotive Engine, including:
- Instructions for removing and installing the front housing, which includes removing covers, brackets, and bolts.
- Procedures for removing and installing the front gear group, which involves removing shafts and bushings.
- Steps for removing and installing the rear housing, such as disconnecting hoses, removing bolts, and lifting off the housing.
The document provides detailed illustrations and numbered steps for each procedure, and lists any required tools. Safety notices are included to keep parts clean and contain fluids.
This document provides installation and removal instructions for various components of a C27 Locomotive Engine, including:
- Instructions for removing and installing the front housing, which houses components like the oil filter and dampers.
- Procedures for removing and installing the front gear group, which involves bushings and shafts.
- Steps for removing the rear housing, which covers the rear of the engine and requires disconnecting hoses and brackets.
The document provides detailed illustrations and numbered steps for each procedure, and lists any required tools. Safety notices are included to keep parts clean and contain fluids.
This document provides installation and removal instructions for components of a C27 industrial locomotive engine. It includes procedures for removing and installing the front housing, gear group, crankshaft front seal, and rear housing. The front housing removal procedure involves disconnecting hoses and harnesses, removing dampers and brackets, and lifting the housing off. The gear group installation procedure specifies using tools to install bushings and tightening bolts to specified torques.
This document provides installation and removal instructions for components of a C27 industrial locomotive engine. It includes procedures for removing and installing the front housing, gear group, crankshaft front seal, and rear housing. The front housing removal procedure involves disconnecting hoses and harnesses, removing dampers and brackets, and lifting the housing off. The gear group installation procedure specifies using tools to install bushings at precise dimensions and torquing bolts to specified values.
This document provides installation and removal instructions for components of a C27 industrial locomotive engine. It includes procedures for removing and installing the front housing, gear group, crankshaft front seal, and rear housing. The front housing removal procedure involves disconnecting hoses and harnesses, removing dampers and brackets, and lifting the housing off. The gear group installation procedure specifies using tools to install bushings at precise dimensions and torquing bolts to specified values.
This document provides instructions for removing and installing various components of a C27 Industrial Engine, including:
1. Removing the front gear group by removing bolts and gear assemblies.
2. Removing the front housing by removing covers, dampers, brackets, and bolts to detach the housing.
3. Removing the rear housing by removing elbow assemblies, bolts connecting the oil pan, and disconnecting hose assemblies.
The document provides instructions for removing and installing the front housing on a C27 Industrial Engine. It describes removing covers, brackets, bolts, and the front housing itself. Tools needed are listed. Removal involves disconnecting hoses and electrical connections. Installation specifies applying sealant, installing gaskets and components in reverse order of removal, and tightening bolts to the specified torques.
This document provides installation and removal instructions for various components of a C27 Locomotive Engine, including:
- Instructions for removing and installing the front housing, which includes removing covers, brackets, bolts and the housing itself.
- Procedures for removing and installing the front gear group, which involves removing shafts, bushings, plates and gears.
- Steps for removing the rear housing, such as disconnecting hoses, removing bolts, and lifting off the housing.
The document provides detailed illustrations and numbered steps for each procedure, and lists any required tools. Safety and cleaning notes are included to handle fluids and prevent contamination.
This document provides installation and removal instructions for various components of a C27 Locomotive Engine, including:
- Instructions for removing and installing the front housing, which includes removing covers, brackets, and bolts.
- Procedures for removing and installing the front gear group, which involves removing shafts and bushings.
- Steps for removing and installing the rear housing, such as disconnecting hoses, removing bolts, and lifting off the housing.
The document provides detailed illustrations and numbered steps for each procedure, and lists any required tools. Safety notices are included to keep parts clean and contain fluids.
This document provides installation and removal instructions for various components of a C27 Locomotive Engine, including:
- Instructions for removing and installing the front housing, which houses components like the oil filter and dampers.
- Procedures for removing and installing the front gear group, which involves bushings and shafts.
- Steps for removing the rear housing, which covers the rear of the engine and requires disconnecting hoses and brackets.
The document provides detailed illustrations and numbered steps for each procedure, and lists any required tools. Safety notices are included to keep parts clean and contain fluids.
This document provides installation and removal instructions for components of a C27 industrial locomotive engine. It includes procedures for removing and installing the front housing, gear group, crankshaft front seal, and rear housing. The front housing removal procedure involves disconnecting hoses and harnesses, removing dampers and brackets, and lifting the housing off. The gear group installation procedure specifies using tools to install bushings and tightening bolts to specified torques.
This document provides installation and removal instructions for components of a C27 industrial locomotive engine. It includes procedures for removing and installing the front housing, gear group, crankshaft front seal, and rear housing. The front housing removal procedure involves disconnecting hoses and harnesses, removing dampers and brackets, and lifting the housing off. The gear group installation procedure specifies using tools to install bushings at precise dimensions and torquing bolts to specified values.
This document provides installation and removal instructions for components of a C27 industrial locomotive engine. It includes procedures for removing and installing the front housing, gear group, crankshaft front seal, and rear housing. The front housing removal procedure involves disconnecting hoses and harnesses, removing dampers and brackets, and lifting the housing off. The gear group installation procedure specifies using tools to install bushings at precise dimensions and torquing bolts to specified values.
This document provides installation and removal procedures for components of a C27 industrial locomotive engine:
1) It details the removal and installation of the front gear group, including bushings, shafts, and plates.
2) The removal of the front housing requires disconnecting various components and brackets before lifting the housing off.
3) Reinstallation of the front housing involves lowering it onto dowel pins and torquing bolts in a specific sequence.
This document provides installation and removal procedures for components of a C27 industrial locomotive engine:
1) It details the removal and installation of the front gear group, including bushings, shafts, and plates.
2) The removal of the front housing requires disconnecting various components and brackets before lifting the housing off.
3) Reinstallation of the front housing involves lowering it onto dowel pins and torquing bolts in a specific sequence.
This document provides installation and removal procedures for components of a C27 industrial locomotive engine:
1) It details the removal and installation of the front gear group, including bushings, shafts, and plates.
2) The removal of the front housing requires disconnecting various components and brackets before lifting the housing off.
3) Reinstallation of the front housing involves lowering it onto dowel pins and torquing bolts in a specific sequence.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...yu5676962
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator. The instructions include:
1) Removing the idler gear from the front gear group using a puller tool and driver group.
2) Installing a new crankshaft rear seal using a installer tool, locator, bolts and washer. The seal is pressed onto the crankshaft using the tools.
3) Removing and installing the flywheel housing which requires lifting equipment and removal of bolts, washers and gaskets. The oil seal in the housing is also removed and installed using driver tools.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...ze6074xunong
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves cleaning the crankshaft, applying retaining compound, and pressing the new seal into place using a slide hammer puller. Care must be taken not to damage the crankshaft flange during installation.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...yfjskemdmdm
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...f8usejdkdm3ed
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator. The instructions include:
1) Removing the idler gear from the front gear group using a puller tool and driver group.
2) Installing a new crankshaft rear seal using a installer tool, locator, bolts and washer. The seal is pressed onto the crankshaft using the tools.
3) Removing and installing the flywheel housing which requires lifting equipment and removal of bolts, washers and gaskets. The oil seal in the housing is also removed and installed using driver tools.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...gongfuao7509
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...mbk336997
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...fsejkddmmdmd
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...f8seodkdmdmed3
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...jdksmemd1
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator. The instructions include:
- Removing the idler gear from the front gear group using a puller tool and driver group.
- Installing a new crankshaft rear seal using a installer tool, locator, bolts and washer. The seal is pressed onto the crankshaft using the tools.
- Removing and installing the flywheel housing which requires lifting equipment and removal of bolts, washers and gaskets. The housing weighs approximately 29 kg.
- Procedures are provided in detail with illustrations and lists of required tools. Safety and contamination prevention notices are also
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujskekfksmem
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and apply retaining compound.
2. Position the new seal on the crankshaft flange using a slide hammer puller, ensuring it is seated fully and evenly.
3. Inspect the installed seal and check for proper installation.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
This document provides assembly instructions for the transmission of a 434E BACKHOE LOADER model. It lists the required tools and notes on cleanliness and lubrication. It then provides step-by-step instructions with illustrations for assembling the various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft (rear). Proper compression of springs and installation of seals, bearings, gears and other parts is described.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
More Related Content
Similar to Caterpillar Cat C27 Industrial Engine (Prefix RAM) Service Repair Manual (RAM00001 and up).pdf
This document provides installation and removal procedures for components of a C27 industrial locomotive engine:
1) It details the removal and installation of the front gear group, including bushings, shafts, and plates.
2) The removal of the front housing requires disconnecting various components and brackets before lifting the housing off.
3) Reinstallation of the front housing involves lowering it onto dowel pins and torquing bolts in a specific sequence.
This document provides installation and removal procedures for components of a C27 industrial locomotive engine:
1) It details the removal and installation of the front gear group, including bushings, shafts, and plates.
2) The removal of the front housing requires disconnecting various components and brackets before lifting the housing off.
3) Reinstallation of the front housing involves lowering it onto dowel pins and torquing bolts in a specific sequence.
This document provides installation and removal procedures for components of a C27 industrial locomotive engine:
1) It details the removal and installation of the front gear group, including bushings, shafts, and plates.
2) The removal of the front housing requires disconnecting various components and brackets before lifting the housing off.
3) Reinstallation of the front housing involves lowering it onto dowel pins and torquing bolts in a specific sequence.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...yu5676962
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator. The instructions include:
1) Removing the idler gear from the front gear group using a puller tool and driver group.
2) Installing a new crankshaft rear seal using a installer tool, locator, bolts and washer. The seal is pressed onto the crankshaft using the tools.
3) Removing and installing the flywheel housing which requires lifting equipment and removal of bolts, washers and gaskets. The oil seal in the housing is also removed and installed using driver tools.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...ze6074xunong
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves cleaning the crankshaft, applying retaining compound, and pressing the new seal into place using a slide hammer puller. Care must be taken not to damage the crankshaft flange during installation.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...yfjskemdmdm
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...f8usejdkdm3ed
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator. The instructions include:
1) Removing the idler gear from the front gear group using a puller tool and driver group.
2) Installing a new crankshaft rear seal using a installer tool, locator, bolts and washer. The seal is pressed onto the crankshaft using the tools.
3) Removing and installing the flywheel housing which requires lifting equipment and removal of bolts, washers and gaskets. The oil seal in the housing is also removed and installed using driver tools.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...gongfuao7509
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...mbk336997
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...fsejkddmmdmd
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...f8seodkdmdmed3
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...jdksmemd1
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator. The instructions include:
- Removing the idler gear from the front gear group using a puller tool and driver group.
- Installing a new crankshaft rear seal using a installer tool, locator, bolts and washer. The seal is pressed onto the crankshaft using the tools.
- Removing and installing the flywheel housing which requires lifting equipment and removal of bolts, washers and gaskets. The housing weighs approximately 29 kg.
- Procedures are provided in detail with illustrations and lists of required tools. Safety and contamination prevention notices are also
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujskekfksmem
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and apply retaining compound.
2. Position the new seal on the crankshaft flange using a slide hammer puller, ensuring it is seated fully and evenly.
3. Inspect the installed seal and check for proper installation.
Similar to Caterpillar Cat C27 Industrial Engine (Prefix RAM) Service Repair Manual (RAM00001 and up).pdf (19)
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
This document provides assembly instructions for the transmission of a 434E BACKHOE LOADER model. It lists the required tools and notes on cleanliness and lubrication. It then provides step-by-step instructions with illustrations for assembling the various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft (rear). Proper compression of springs and installation of seals, bearings, gears and other parts is described.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
This document provides instructions for disassembling and removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support tubes to lift the front and rear of the machine, draining the transmission fluid.
2) Removing mounting bolts, brackets and hoses to separate the transmission from the engine and rear axle housing.
3) Using overhead lift equipment to remove the transmission once it is fully separated from the machine.
The document provides instructions for disassembling and removing various components of a 432F2 backhoe loader, including the axle housing, brake assembly, differential and bevel gear, solenoid valve, and releasing system pressure. Key steps include using various tools to remove bearings, gears, pins, seals, and other parts. Precautions are outlined for releasing spring pressure safely.
This document provides disassembly instructions for the transmission of a 432E Backhoe Loader. It lists required tools and outlines 14 steps to fully disassemble the transmission. These include removing various gears, shafts, seals, bearings and other components from the front output shaft, rear output shaft, countershaft, idler shaft, and input shaft. Special care and tools are noted for removing springs and releasing pressurized components. The goal is to break down the transmission into its core individual parts for maintenance or replacement.
The document provides instructions for removing and disassembling the transmission of a 432D backhoe loader. It lists the required tools and gives step-by-step instructions to drain the transmission oil, remove mounting bolts, disconnect electrical connectors, and use lifting tools to safely remove the transmission. Cleanliness is emphasized when disassembling internal components to prevent dirt contamination.
This document provides instructions for removing and installing an engine on a 432E Backhoe Loader. It outlines 50 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses and hoses, and removing mounting hardware. Tools required are listed. To install the engine, the 50 removal steps are reversed, taking care when connecting wiring harnesses and positioning mounting bolts. Proper lifting equipment is needed due to the engine weighing approximately 454 kg.
The document provides instructions for removing an engine oil cooler from a 432D BACKHOE LOADER, which includes draining fluids, removing housing bolts and seals, and removing the oil cooler. It then provides instructions for installing a new oil cooler, which includes cleaning surfaces, installing new seals and bolts, and refilling fluids. Separate instructions are given for removing and installing an engine oil relief valve.
This document provides instructions for installing an engine in a 430F2 backhoe loader. It describes lifting the engine into place using load leveling beams, aligning and bolting the bell housing and flywheel, installing engine mounts and accessories like the starter motor, alternator, and air conditioning compressor, and filling fluids like coolant and oil. The final steps include installing panels and covers to complete the engine installation.
This service repair manual provides instructions for removing and installing exhaust manifolds and inlet manifolds on Caterpillar 3054 engines. It describes removing manifold bolts and nuts, removing gaskets, cleaning parts, installing new gaskets, reinstalling manifolds and tightening bolts or nuts to the specified torque for both type 1, type 2 and 7BJ engines. The document is from the Caterpillar Service Information System and provides detailed step-by-step instructions and illustrations for mechanics performing maintenance on Caterpillar equipment.
The document provides instructions for removing and installing a crankshaft rear seal and flywheel housing on a Caterpillar 430F2 backhoe loader. It describes using various tools to remove torx screws and seals, cleaning parts, installing a new seal with a plastic sleeve, and tightening bolts to specified torques. The instructions are part of a service manual for maintenance and repair of engine components.
This document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 430F2 backhoe loader with a C4.4 engine. It outlines the necessary tools and describes a 7 step process for removal and a 9 step process for installation. Safety notices are included to keep parts clean and prevent damage during the procedure.
This document provides instructions for removing and installing a hydraulic tank on a 430F backhoe loader. The removal procedure involves disconnecting hoses from the tank, removing clamps, and taking out bolts to detach the tank assembly. Components like a strainer and gauge are then removed from the tank. Reinstallation involves reversing these steps and reattaching all hoses, clamps, and bolts.
This document provides instructions for removing and installing the front gear group of a C4.4 engine. The procedure involves:
1. Locking the crankshaft and camshaft in position using timing pins.
2. Marking the gears to ensure proper reinstallation.
3. Removing the fuel pump, camshaft, and idler gears.
4. Cleaning and inspecting the gear components.
5. Reinstalling the gears, ensuring proper timing and backlash measurements.
The document provides instructions for disassembling and assembling the direct drive transmission of a 430E Backhoe Loader. It lists required tools and gives step-by-step instructions to remove components such as gears, bearings, seals, and shafts. It describes using various tools to press, pull, or remove parts. Reassembly is to be done in major components and with a focus on cleanliness.
The document provides instructions for removing a hydraulic tank from a 428E BACKHOE LOADER. It involves draining the hydraulic oil, removing various panels and covers, and disconnecting hoses and harnesses. Key steps include removing bolts and panels to access the tank, then disconnecting multiple hose assemblies and a harness connecting to the tank before it can be lifted out. The process requires draining fluid first and removes parts in a specific sequence for access.
This document provides instructions for removing and installing various components of a Caterpillar 3054C diesel engine, including:
- Lifter group removal and installation
- Camshaft removal and installation
- Camshaft bearing removal and installation
- Engine oil pan removal and installation
The summaries include detailed step-by-step instructions, required tools, safety notices, and references to other relevant sections for complete disassembly and reassembly. Precautions are outlined to prevent contamination and damage to parts.
This document provides instructions for removing and installing fuel injection nozzles and the fuel injection pump on a Caterpillar 3054 engine. It describes in detail:
- Removing fuel injection lines before removing nozzles or pump
- Using timing pins to ensure proper alignment when removing the pump
- Cleaning parts and applying anti-seize compound when installing nozzles
- Torque specifications for reinstalling nozzles and pump components
The document is from a service repair manual and contains detailed step-by-step instructions and illustrations for working on specific engine systems.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE RAM
Configuration: C27 Industrial Engine RAM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -KENR8167-05 Publication Date -01/08/2015 Date Updated -30/04/2018
i05933887
Gear Group (Front) - Remove
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
6V-4869 Adapter 1
6V-6174 Plug 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g01147593
1. Remove bolts (5) and gear assembly (4).
2. Remove bolts (3) and plate (2). Remove gear assembly (1).
Illustration 2 g03729282
2/3(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 3. Remove bolts (6) and shaft (7).
Note: The crankshaft will have to be removed to remove and install bushings (8) and
(9). Refer to Disassembly and Assembly, "Crankshaft - Remove".
4. If necessary, use Tooling (A) to remove bushing (8) and (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 17 23:15:43 UTC+0800 2020
3/3(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE RAM
Configuration: C27 Industrial Engine RAM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -KENR8167-05 Publication Date -01/08/2015 Date Updated -30/04/2018
i06280625
Gear Group (Front) - Install
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
6V-4869 Adapter 1
6V-6174 Plug 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 1 g03729299
Illustration 2 g03729282
1. Use Tooling (A) to install bushings (8) and (9) . Install bushing (8) to a Dimension (B) .
Dimension (B) is 236.7 ± 0.5 mm (9.32 ± 0.02 inch). Install bushing (9) to a Dimension
(A) . Dimension (A) is 40.4 ± 0.5 mm (1.59 ± 0.02 inch). Install the crankshaft. Refer to
Disassembly and Assembly, "Crankshaft - Install".
2. Apply clean engine oil to shaft (7) , the bearing bore, and the thrust faces prior to
installation. Install shaft (7) and bolts (6) . Tighten bolts (6) to a torque of 55 ± 10 N·m (41
± 7 lb ft).
2/3(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 3 g01147593
3. Position gear assembly (1) on the shaft. Install plate (2) and bolts (3) .
4. Install gear assembly (4) and bolts (5) .
End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 17 23:16:39 UTC+0800 2020
3/3(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE RAM
Configuration: C27 Industrial Engine RAM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -KENR8167-05 Publication Date -01/08/2015 Date Updated -30/04/2018
i02292574
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Start By:
a. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
b. Remove the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front
Seal - Remove".
c. Remove the water temperature regulator housing. Refer to Disassembly and Assembly,
"Water Temperature Regulator Housing - Remove and Install".
d. Remove the front engine support. Refer to Disassembly and Assembly, "Engine Trunnion -
Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01147751
1. Remove covers (1).
2. Disconnect harness assembly (2).
3. Remove three bolts (3).
4. Loosen bolt (4) and reposition the filter housing assembly. Tighten bolt (4).
5. Use Tooling (A) to remove engine oil filter (5).
2/4(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 2 g01147758
6. Remove bolts (6) and dampers (7).
Illustration 3 g01147761
7. Remove bracket (8) and engine trunnion (9).
Illustration 4 g01147762
3/4(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 8. Disconnect bracket (10) and elbows (11).
Illustration 5 g01147777
9. Remove adapters (12) and bolts (13).
Illustration 6 g01147783
10. Attach a suitable lifting device to front housing (14). The weight of front housing (14) is
approximately 70 kg (154 lb).
11. Remove bonnet (15).
12. Remove bolts (16) and bolts (17).
13. Remove front housing (14) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 17 23:17:34 UTC+0800 2020
4/4(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE RAM
Configuration: C27 Industrial Engine RAM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -KENR8167-05 Publication Date -01/08/2015 Date Updated -30/04/2018
i06746008
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B Loctite 598 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 1 g01147783
1. Apply Tooling (B) to the bottom of front housing (14) at the junction of the cylinder block
and the engine oil pan.
2. Attach a suitable lifting device to front housing (14). The weight of front housing (14) is
approximately 70 kg (154 lb). Position the gasket and front housing (14) on the dowel pins
on the cylinder block.
3. Install bolts (16) and bolts (17).
4. Install bonnet (15).
5. Trim the gasket between the front housing and the cylinder block even with the bottom of
the front housing.
Illustration 2 g01147777
6. Install bolts (13) and adapters (12).
Illustration 3 g01147762
7. Connect elbows (11) and bracket (10).
2/5(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 4 g01147761
8. Install engine trunnion (9) and bracket (8).
Illustration 5 g01147758
3/5(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 6 g01151441
9. Install dampers (7) and bolts (6).
10. Tighten the bolts to a torque of 240 ± 40 N·m (177 ± 30 lb ft). Tighten the bolts in the
following sequence: 1, 4, 2, 5, 3, 6, 1, 4.
Illustration 7 g01147751
11. Install engine oil filter (5).
12. Reposition the filter housing assembly and tighten bolt (4).
13. Install bolts (3).
14. Connect harness assembly (2).
15. Install covers (1).
End By:
a. Install the front engine support. Refer to Disassembly and Assembly, "Engine Trunnion -
Remove and Install".
4/5(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. b. Install the water temperature regulator housing. Refer to Disassembly and Assembly,
"Water Temperature Regulator Housing - Remove and Install".
c. Install the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front
Seal - Install".
d. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 17 23:18:30 UTC+0800 2020
5/5(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE RAM
Configuration: C27 Industrial Engine RAM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -KENR8167-05 Publication Date -01/08/2015 Date Updated -30/04/2018
i04032306
Housing (Rear) - Remove
SMCS - 1157-011
Removal Procedure
Start By:
a. Remove the rear gear group.
b. Remove the fuel transfer pump.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02223214
1/3(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. 1. Remove elbow assemblies (1)
2. Remove the bolts (2) that hold the engine oil pan to the rear housing (3).
Illustration 2 g02223255
3. Disconnect hose assembly (4). Remove bolts (5).
Illustration 3 g02223273
2/3(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 4 g02224580
4. Remove bracket assembly (7). Remove clip (8).
5. Attach a suitable lifting device to rear housing (3). The weight of rear housing (3) is
approximately 84 kg (185 lb).
6. Remove bolts (6).
7. Remove rear housing (3) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 17 23:19:26 UTC+0800 2020
3/3(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE RAM
Configuration: C27 Industrial Engine RAM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -KENR8167-05 Publication Date -01/08/2015 Date Updated -30/04/2018
i07362121
Housing (Rear) - Install
SMCS - 1157-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9612 Silicone Sealant 1
B — Loctite LV Core Plug Sealant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 1 g06295353
1. If cup plugs (11) were removed or the rear housing is being replaced, use Tooling (B) on
cup plugs (11) and install to Dimension (X).
Dimension (X) ... 1.25 ± 0.25 mm (0.05 ± 0.01 inch)
2. Apply Tooling (A) to the bottom of the rear housing at the junction of the cylinder block
and the engine oil pan.
Illustration 2 g02223273
2/4(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 3 g02223413
Bolt tightening sequence
3. Attach a suitable lifting device to rear housing (3). The weight of rear housing (3) is
approximately 84 kg (185 lb).
4. Position the gasket on rear housing (3).
5. Position rear housing (3) on the cylinder block. Install bolts (6). Tighten bolts (3) in a
numerical sequence to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
6. Trim the gasket between the rear housing and the cylinder block even with the bottom of the
rear housing.
3/4(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 4 g02223255
7. Install bolts (4).
8. Connect hose assembly (5).
Illustration 5 g02223214
9. Install bolts (2) that hold the engine oil pan to rear housing (3).
10. Tighten all the bolts that hold the engine oil pan evenly to raise the engine oil pan into
position.
End By:
a. Install the rear gear group. Refer to Disassembly and Assembly, "Gear Group (Rear) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 17 23:20:22 UTC+0800 2020
4/4(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE RAM
Configuration: C27 Industrial Engine RAM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -KENR8167-05 Publication Date -01/08/2015 Date Updated -30/04/2018
i06258895
Fumes Disposal Filter - Remove and Install - Flywheel
Housing
SMCS - 1317-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A − LOCTITE 5900 1
B − KRYTOX LS23 1
Illustration 1 g02320813
1. Remove clips (2), and (6) .
1/2(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. 2. Remove bracket assembly (3) and tube (4) .
3. Remove bolts (5) and fumes disposal group (1) .
Illustration 2 g02320886
4. Remove plate (10) .
5. Remove element (9) and remove O-ring seal (8) from base (7) .
Installation Procedure
1. Install fumes disposal group (1) in reverse order.
a. Apply Tooling (A) at Location (X). Location (X) is the sealing surface between the
base and the plate.
b. Apply Tooling (B) to O-ring seal (8) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 17 23:21:17 UTC+0800 2020
2/2(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE RAM
Configuration: C27 Industrial Engine RAM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -KENR8167-05 Publication Date -01/08/2015 Date Updated -30/04/2018
i06258903
Fumes Disposal Filter - Remove and Install
SMCS - 1317-010
Removal Procedure
Illustration 1 g02313033
1. Disconnect hose assemblies (1), (4), and (5) .
2. Remove brackets (3) and remove the fumes disposal group (2) .
1/2(W)
w
2020/6/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...