Caterpillar Cat 428E BACKHOE LOADER (Prefix SNL) Service Repair Manual (SNL00001 and up).pdf

Service Repair Manual
Model
428E BACKHOE LOADER

Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428E BACKHOE LOADER SNL
Configuration: 428E Backhoe Loader Parallel Lift SNL00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders
Machine Systems
Media Number -RENR6485-08 Publication Date -01/01/2013 Date Updated -24/01/2013
i02307250
Piston Pump - Assemble
SMCS - 5070-016; 5455
S/N - CBD1-UP
S/N - ELB1-UP
S/N - HBE1-UP
S/N - SHA1-UP
S/N - SNL1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
1/9
428E Backhoe Loader Parallel Lift SNL00001-UP (MACHINE) POWERED BY 3054...
2019/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g01155697
1. Install bearing cup (45) and lip seal (44) .
2. Use Tooling (A) in order to install retaining ring (43) .
3. Install bearings (41) and bearing cone (42) .
2/9
2019/9/25

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
4. Remove retaining ring (39), pin (40), spring (36), and piston (37) from swashplate (38) .
5. Remove swashplate (38) .
6. Compress spring (36). Install piston (37) into the original position.
7. Install shaft (34) and O-ring seal (36) .
3/9
2019/9/25

injury.
8. Install washer (33), spring (32), and washer (31) .
9. Use a suitable press in order to install retaining ring (30) .
4/9
2019/9/25

10. Install pins (29) .
11. Install bearing (28) .
12. Install retainer (27) and pistons (26) .
5/9
2019/9/25

13. Install rotating group (25) .
14. Install bearing cone (24) .
6/9
2019/9/25

15. Install bearing cup (23) and port plate (22) .
16. Install head (21) and bolts (20) .
injury.
17. Install spool (8), retainer (9), spring (10), spring (11), O-ring seal (12), and plug (13) .
7/9
2019/9/25

18. Install spool (14), retainer (15), spring (16), spring (17), O-ring seal (18), and plug (19) .
19. Install plug (6) and screws (7) .
20. Install plug (4) and plug (5) .
8/9
2019/9/25

21. Install O-ring seals (3) .
22. Install valve (2) and bolts (1) .
End By: Install the pump. Refer to Disassembly and Assembly, "Piston Pump - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 25 22:03:07 UTC+0800 2019
9/9
2019/9/25

Shutdown SIS
Previous Screen
Machine Systems
i02221849
Piston Pump - Install
SMCS - 5070-012; 5455
S/N - BXE1-UP
S/N - CBD1-UP
S/N - DDT1-UP
S/N - EAT1-UP
S/N - FSH1-UP
S/N - GKZ1-UP
S/N - HBE1-UP
S/N - HLS1-UP
S/N - KMW1-UP
S/N - LBE1-UP
S/N - MFG1-6000
S/N - SHA1-UP
S/N - SNL1-UP
Installation Procedure
1/3
2019/9/25

1. Attach a suitable lifting device to piston pump (13). The weight of piston pump (13) is
approximately 50 kg (110 lb). Raise piston pump (13) into position through the bottom of
the machine. Install bolts (12) .
2. Connect hose assemblies (9) and (11). Connect hose (10) .
2/3
2019/9/25

3. Connect hose assembly (7). Connect harness assembly (8). Close drain valve (6) .
4. Install floorplate (4) and install bolts (5) .
5. Install floor mat (1). Install plate (2) and bolts (3). Repeat for the other side.
End By: Install the rear drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Rear) -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 25 22:03:54 UTC+0800 2019
3/3
2019/9/25

Shutdown SIS
Previous Screen
Machine Systems
i02215278
Hydraulic Tank - Remove
SMCS - 5056-011
Removal Procedure
Start By:
A. Remove the side panels. Refer to Disassembly and Assembly, "Side Panels - Remove and
Install".
1. Drain the hydraulic oil into a suitable container for storage or disposal. Refer to Operation
and Maintenance Manual, "Hydraulic System Oil - Change".
2. Remove plate (2) on each side of the cab. Remove floor mat (1) .
1/18
2019/9/25

3. Remove floorplate (3) .
4. Remove bolts (4) and lift panel (5) .
2/18
2019/9/25

5. Disconnect harness assemblies (6) and (7). Remove panel (5) .
6. Remove bolts (8) .
3/18
2019/9/25

7. Remove bolts (9) and cover (10) .
8. Remove cover (11) .
4/18
2019/9/25

9. Remove bolts (12). Remove cover (13) .
10. Remove bolt (14) and panel (15) .
11. Remove bolts (16) .
5/18
2019/9/25

12. Remove bolts (17) and panel (18) .
13. Remove bolts (20). Lift floorplate (19) .
6/18
2019/9/25

14. Disconnect harness assembly (21). Remove floorplate (19) .
15. Remove duct (22) .
7/18
2019/9/25

16. Disconnect hose (23). Repeat for the other side. Remove cover (24) .
17. Remove duct (25) .
8/18
2019/9/25

18. Remove nut (27) and bolts (28). Repeat for the other side. Remove panel (26) .
19. Disconnect hose assemblies (29), (30), (31) and (32) .
9/18
2019/9/25

20. Remove the cable straps and disconnect harness assembly (33) .
21. Remove bolt (34) and place harness assembly (33) to the side.
10/18
2019/9/25

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

22. Disconnect hose (37). Disconnect hose assemblies (35) and (36) .
Note: Hose (37) will remain with the hydraulic oil tank.
23. Place steering column assembly (38) to the side.
11/18
2019/9/25

24. Remove bolts (39) and panel (40) .
25. Remove bolt (41) .
12/18
2019/9/25

26. Disconnect hose assembly (42) from the bank valve that is located on the bottom of the
machine.
27. Disconnect hose (44) from hydraulic oil tank (43) .
13/18
2019/9/25

28. Disconnect hose (45) .
Note: Hose assemblies (42) and (37) that were previously disconnected will remain
connected to the hydraulic oil tank.
29. Disconnect hose (46) .
14/18
2019/9/25

Caterpillar Cat 428E BACKHOE LOADER (Prefix SNL) Service Repair Manual (SNL00001 and up).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 428E BACKHOE LOADER (Prefix SNL) Service Repair Manual (SNL00001 and up).pdf

Similar to Caterpillar Cat 428E BACKHOE LOADER (Prefix SNL) Service Repair Manual (SNL00001 and up).pdf (6)

More from fjisejkdmd8id

More from fjisejkdmd8id (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 428E BACKHOE LOADER (Prefix SNL) Service Repair Manual (SNL00001 and up).pdf