This document provides assembly instructions for the transmission of a 434E BACKHOE LOADER model. It lists the required tools and notes on cleanliness and lubrication. It then provides step-by-step instructions with illustrations for assembling the various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft (rear). Proper compression of springs and installation of seals, bearings, gears and other parts is described.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434E BACKHOE LOADER SJL
Configuration: 434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train
Media Number -KENR8841-01 Publication Date -01/05/2014 Date Updated -14/05/2014
i03625932
Transmission (Power Shift) - Assemble
SMCS - 3030-016-PM; 3066-016
S/N - EME1-UP
S/N - JBA1-UP
S/N - NBA1-UP
S/N - SJL1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7502 Transmission Repair Stand 1
B 138-7575 Link Bracket 1
C
152-7085 (1)
Transmission Shaft Handler 1
189-0409 Shackle As 1
G 152-7055 Spring Compressor 1
H 2P-8312 Retaining Ring Pliers 1
J 8T-5096 Dial Indicator Gp 1
K 6V-6640 Sealant -
L 9S-3263 Thread Lock Compound -
M 1U-6396 O-Ring Assembly Compound -
1/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. ( 1 )
CE Compliant
Note: The transmission will be assembled in major components. The major components will then
be assembled.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Note: Apply a light film of clean transmission oil to all components before assembly.
Note: O-ring seals, gaskets, and seals should always be replaced. A used O-ring seal may not have
the same sealing properties as a new O-ring seal. Use Tooling (M) during the assembly procedure.
Illustration 1 g00731364
1. During the installation of all the needle bearings on the shafts, the open end of cups (1) must
point away from the bearings or gears that are contacted.
Reverse Shaft
2/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01246293
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
3. Use a suitable press and Tooling (G) in order to compress spring assembly (15). Use
Tooling (H) in order to install retaining ring (16) .
Illustration 6 g01246287
4. Install friction discs (13) and plates (14) .
4/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g01246286
5. Install end plate (12) and retaining ring (11) .
Illustration 8 g01246283
6. Install thrust washer (8), needle bearing (9) and roller bearing (10) .
Illustration 9 g01246273
5/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g01246678
7. Install gear (4). Install roller bearing (5), needle bearing (6), and thrust washer (7). Raise the
temperature of bearing cone (3). Install bearing cone (3) .
Illustration 11 g01246261
8. Install seal rings (1) onto reverse shaft (2) .
Illustration 12 g01656734
6/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 9. Raise the temperature of bearing cone (18). Install bearing cone (18) .
Input Shaft
Illustration 13 g01944908
1. Install piston (34) .
Illustration 14 g01944905
2. Install spring assembly (33) .
7/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g01656600
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
3. Use a suitable press and Tooling (G) in order to compress spring assembly (33). Use
Tooling (H) in order to install retaining ring (34) .
Illustration 16 g01656599
4. Install discs (31) and plates (32) .
8/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g01656598
5. Install end plate (30) and retaining ring (29) .
Illustration 18 g01656597
6. Install thrust washer (28) and needle bearing (27). Install roller bearings (25) and (26) .
Illustration 19 g01656596
7. Install gear (24) .
9/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g01656595
8. Install needle bearing (23) and thrust washer (22) .
Illustration 21 g01656833
9. Raise the temperature of bearing cone (21). Install bearing cone (21) .
10. Install ring (20) .
10/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 22 g01246791
11. Install piston (19) .
Illustration 23 g01246064
12. Install spring assembly (17) .
Illustration 24 g01246042
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
11/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 13. Use Tooling (G) and a suitable press in order to compress spring assembly (17). Use
Tooling (H) in order to install retaining ring (18) .
Illustration 25 g01245995
14. Install discs (15) and plates (16) .
Illustration 26 g01245971
15. Install retaining ring (13) and end plate (14) .
12/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
3. Use Tooling (G) and a suitable press in order to compress spring assembly (19). Use
Tooling (H) in order to install retaining ring (20) .
Illustration 35 g01245801
4. Install friction discs (17) and plates (18) .
Illustration 36 g01245782
5. Install end plate (16) and retaining ring (15) .
16/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 47 g01656159
2. Install spring assembly (29) .
Illustration 48 g01656156
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
3. Use a suitable press and Tooling (G) in order to compress spring assembly (29). Use
Tooling (H) in order to install retaining ring (30) .
Illustration 49 g01656155
21/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 4. Install friction discs (27) and plates (28) .
Illustration 50 g01656153
5. Install end plate (26) and retaining ring (25) .
Illustration 51 g01656139
6. Install thrust washer (20), needle bearing (21), roller bearing (22), spacer (23) and roller
bearing (24) .
22/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 52 g01656937
7. Raise the temperature of gear (19). Install gear (19) .
Illustration 53 g01656974
8. Raise the temperature of bearing cone (18). Install bearing cone (18) .
Illustration 54 g01950479
9. Install piston (17) .
23/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 55 g01950484
10. Install spring assembly (15) .
Illustration 56 g01245444
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
11. Use a suitable press and Tooling (G) in order to compress spring assembly (15) and use
Tooling (H) in order to install retaining ring (16) .
24/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 57 g01245422
12. Install friction discs (13) and plates (14) .
Illustration 58 g01245412
13. Install end plate (12) and retaining ring (11) .
Illustration 59 g01245407
14. Install thrust washer (10), needle bearing (9) and roller bearing (8) .
25/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 60 g01245400
15. Install gear (4), roller bearing (5), needle bearing (6) and thrust washer (7). Raise the
temperature of bearing cone (3). Install bearing cone (3) .
Illustration 61 g01245395
16. Install seal rings (1) and (2) .
Output Shaft (Front)
26/41
434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...