Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972G WHEEL LOADER 7LS
Configuration: 972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
966G and 972G Wheel Loaders Power Train
Media Number -RENR2106-08 Publication Date -01/05/2004 Date Updated -28/05/2004
i02642179
Transmission from Output Transfer Gears - Separate
SMCS - 3002-076
Separation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
Start By:
A. Separate the torque converter from the transmission. Refer to Disassembly and Assembly,
"Torque Converter from Transmission, Output Transfer Gears - Separate".
Note: Put identification marks on all harness assemblies for installation purposes. Plug all tube
assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the
system.
1/3
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01325525
1. Remove bolts (1) and remove drain tube assembly (2) .
Illustration 2 g01325543
2. Attach Tooling (A) and a suitable lifting device to transmission planetary (4) .
3. Remove O-ring seal (3) .
Illustration 3 g01325555
2/3
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g01325557
4. Disconnect harness assemblies (6). Disconnect harness assembly (8) .
5. Remove bolts (5) which hold transmission planetary (4) to output transfer gear case (7) .
Note: If necessary, use forcing screws in order to separate transmission planetary (4) from
output transfer gear case (7) .
6. Use Tooling (A) and the suitable lifting device in order to separate transmission planetary
(4) from output transfer gear case (7). The weight of transmission planetary (4) is
approximately 545 kg (1200 lb).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 11 19:11:25 UTC+0800 2021
3/3
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972G WHEEL LOADER 7LS
Configuration: 972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
966G and 972G Wheel Loaders Power Train
Media Number -RENR2106-08 Publication Date -01/05/2004 Date Updated -28/05/2004
i02299775
Transmission Planetary - Disassemble
SMCS - 3160-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-0520 Driver Gp 1
C 8H-0663 Bearing Puller 1
Start By:
A. Separate the transmission from the output transfer gears. Refer to Disassembly and
Assembly, "Transmission from Output Transfer Gears - Separate".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
1/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00458960
1. Remove O-ring seal (1) from the housing.
2. Remove bolt (3), retainer (2), and drive gear (4) from the end of the input shaft.
Illustration 2 g00459007
3. Remove plate (5) .
Illustration 3 g00459030
2/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 4. Attach Tooling (A) and a suitable lifting device to the transmission, as shown. The weight
of the transmission is approximately 544 kg (1200 lb).
5. Carefully position the planetary group on the opposite end so that No. 6 clutch housing (6)
is facing upward, as shown.
Illustration 4 g00459073
6. Remove retaining ring (8) from output shaft (7) .
Illustration 5 g00459075
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 7. Remove bolts (9) and No. 6 clutch housing (6). Mark the location of the long bolts.
Illustration 6 g00459079
8. Remove clutch piston (10) from No. 6 clutch housing (6) .
9. Remove seal rings (11) and (12) from clutch piston (10) .
Illustration 7 g00459087
10. Remove clutch plate (14) and springs (13) .
4/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 11 g00459138
14. Remove metal seal ring (20) from carrier assembly (19) .
Illustration 12 g00459150
15. Use a hammer and a punch to push the spring pins through carrier assembly (19) and into
planetary shafts (21) .
6/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 13 g00459151
16. Use a hammer and a punch to remove planetary shafts (21) from carrier assembly (19) .
Illustration 14 g00324725
17. Remove thrust discs (22), planetary gears (23), and bearings (24) from the carrier assembly.
Remove spring pins (25) from planetary shafts (21) .
Illustration 15 g00459161
18. Remove O-ring seal (26). Remove bolts (27) from manifold (28) .
7/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 16 g00565113
19. Disconnect the harness assemblies which are attached to transmission modulating valves
(29). Remove transmission modulating valves (29) from the transmission housing.
Illustration 17 g00459316
20. Remove retaining ring (32) and gear (30). Remove retaining ring (31) .
Illustration 18 g00459322
8/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 21. Use Tooling (A) and a suitable lifting device to remove manifold (28). The weight of
manifold (28) is approximately 85 kg (190 lb).
22. Remove bolt (33) which holds the harness assembly in place.
Illustration 19 g00459352
23. Remove retaining ring (34) and bearing (35) from manifold (28) .
Illustration 20 g00459369
24. Remove retaining ring (36) and clutch housing (37) .
9/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 21 g00459372
25. Remove O-ring seal (38) from clutch housing (37) .
Illustration 22 g00459375
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
26. Use steel spacers and a suitable press to push on retainer plate (40). Remove retaining ring
(39) from the clutch housing.
10/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 23 g00459387
27. Separate retaining ring (39), retainer plate (40), three coned disc springs (41), and clutch
piston (42) .
Illustration 24 g00459393
28. Remove seal rings (43) from clutch piston (42) .
Illustration 25 g00459394
11/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 29. Remove seal rings (44) from clutch housing (37) .
Illustration 26 g00565119
30. Remove retaining ring (45) from the output shaft. Remove hub (46) .
Illustration 27 g00565685
31. Remove friction discs (47) and clutch plates (48) .
12/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 31 g00459506
35. Remove seal rings (57) and (58) from clutch piston (54) .
Illustration 32 g00565199
36. Use Tooling (A) and a suitable lifting device to remove housing (59). The weight of housing
(59) is approximately 66 kg (145 lb).
Note: The clutch piston may be stuck in housing (59). As housing (59) is removed, the
clutch piston may fall.
14/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 33 g00565203
37. Remove clutch piston (60) .
Illustration 34 g00459540
38. Remove seal rings (61) and (62) from clutch piston (60) .
Illustration 35 g00565255
39. Remove friction discs (63) and clutch plates (64) .
15/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 42. Remove retaining ring (71) and bearing (72) .
Illustration 39 g00459634
43. Use several small steel rods (73) (3.175 mm (0.1250 inch) diameter and one pointed tip) to
compress the retaining ring that holds carrier assembly (69) to ring gear (74) .
44. Remove carrier assembly (69) from ring gear (74) .
Illustration 40 g00459638
45. Remove retaining ring (75) from carrier assembly (69) .
17/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 41 g00459643
46. Use a hammer and a punch to push the spring pins through carrier assembly (69) and into
planetary shafts (76) .
47. Use a hammer and a punch to remove planetary shafts (76) from carrier assembly (69) .
Illustration 42 g00459646
48. Remove thrust discs (77), planetary gears (78), and bearings (79) from the carrier assembly.
Remove spring pins (80) from planetary shafts (76) .
18/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 43 g00565272
49. Remove retaining ring (81) that holds output shaft (82) to the input shaft. Remove output
shaft (82) .
Illustration 44 g00459776
50. Remove O-ring seal (83) from output shaft (82) .
Illustration 45 g00460029
51. Remove retaining ring (85) .
52. Remove sun gear (84) from output shaft (82) .
19/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 46 g00460030
53. Use a suitable press to push output shaft (82) out of bearing (86), as shown.
Illustration 47 g00460034
54. If necessary, remove bearings (87) from both ends of output shaft (82) .
Illustration 48 g00565282
20/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 55. Use Tooling (A) and a suitable lifting device to remove housing (88). The weight of housing
(88) is approximately 61 kg (135 lb).
Illustration 49 g00460042
56. Remove clutch piston (89), friction discs (90), and clutch plates (91) .
Illustration 50 g00460045
57. Remove seal rings (92) and (93) from clutch piston (89) .
21/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 51 g00460067
58. Remove retaining ring (94) from the input shaft.
59. Remove springs (95) and ring gear (96). Remove O-ring seals (97) and (98) .
Illustration 52 g00460068
60. Remove carrier assembly (99) from the input shaft. The weight of the carrier assembly is
approximately 29 kg (65 lb).
22/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 53 g00460074
61. Remove gear (100) .
62. Place a suitable wood block under carrier assembly (99) .
63. Use several small steel rods (101) (2.36 mm (0.093 inch) diameter and one pointed tip) to
compress the retaining ring that holds carrier assembly (99) to ring gear (102) together.
64. Remove ring gear (102) from carrier assembly (99) .
Illustration 54 g00460078
65. Remove retaining ring (105) from carrier assembly (99) .
66. Remove retaining ring (104). Remove sun gear (103) and the bearing. Use Tooling (B) to
remove sun gear (103) and the bearing.
Illustration 55 g00460081
67. Use a hammer and a punch to push the spring pins through carrier assembly (99) and into
planetary shafts (106) .
23/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 56 g00460134
68. Use a hammer and a punch to remove planetary shafts (106) from carrier assembly (99) .
Illustration 57 g00460135
69. Remove thrust discs (107), bearings (109), and planetary gears (108) from the carrier
assembly.
70. Remove spring pins (110) from planetary shafts (106) .
24/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 58 g00460138
71. Remove bearing (111) from sun gear (103) .
Illustration 59 g00460141
72. Remove O-ring seal (112) from sun gear (103) .
Illustration 60 g00460178
73. Remove plate (113) .
25/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 61 g00460181
74. Remove friction discs (114) and clutch plates (117). Remove O-ring seals (115) and (116) .
Illustration 62 g00460207
75. Use several small steel rods (118) (2.36 mm (0.093 inch) diameter and one pointed tip) to
compress the retaining ring that holds coupling (120) to carrier assembly (119). Remove
coupling (120) from carrier assembly (119) .
Note: Coupling (120) and carrier assembly (119) may be removed together at this time. Use
small steel rods (118) in order to separate coupling (120) and carrier assembly (119). See
Step 43 for similar actions.
26/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
32. Illustration 63 g00460208
76. Remove clutch piston (121) from the clutch housing. Remove carrier assembly (119) .
Illustration 64 g00460209
77. Remove seal rings (122) and (123) from clutch piston (121) .
Illustration 65 g00460233
78. Remove retaining ring (124). Use Tooling (B) to remove bearing (125) .
27/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. 79. Remove seal ring (126) from carrier assembly (119) .
Illustration 66 g00460237
80. Use a hammer and a punch to push the spring pins through carrier assembly (119) and into
planetary shafts (127) .
81. Use a hammer and a punch to remove planetary shafts (127) from carrier assembly (119) .
Illustration 67 g00460313
82. Remove thrust discs (128), planetary gears (129), and bearings (130) from the carrier
assembly. Remove spring pins (131) from planetary shafts (127) .
28/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
34. Illustration 68 g00460315
83. Remove retaining ring (132) from housing (133) .
84. Use a soft hammer to remove input shaft (134) from housing (133) .
Illustration 69 g00460318
85. Remove ring seals (136) and O-ring seal (137) from input shaft (134). Remove bearing
(135) .
29/30
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine(SE...
2021/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...