The document provides instructions for removing the camshaft from a 3116 engine that powers a 953C track loader. It describes removing other components first like the governor, side covers and front cover. It notes to keep parts clean and contain fluids. The procedure involves turning the crankshaft to top dead center, aligning camshaft timing marks, and removing the camshaft retainer plate and gear to access the camshaft for removal.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
1. Product: TRACK LOADER
Model: 953C TRACK LOADER 2ZN
Configuration: 953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01935828
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
a. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
b. Remove the governor. Refer to Disassembly and Assembly, "Governor - Remove".
c. Remove the fuel control linkage. Refer to Disassembly and Assembly, "Fuel Injection
Control Linkage - Remove".
d. Remove the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
e. Remove the water temperature regulator housing. Refer to Disassembly and Assembly,
"Water Temperature Regulator Housing - Remove and Install".
f. Remove the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold -
Remove".
g. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: For information on the reusability of the cylinder head, refer to Guideline For Reusable
Parts And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114,
3116, and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 1 g01007597
Typical example
1. Attach a suitable lifting device to the cylinder head.
2/3
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g00654709
2. Remove bolts (1) and (2) that hold the cylinder head to the cylinder block. Carefully remove
the cylinder head from the cylinder block. The cylinder head for the 3116 engine weighs
approximately 85 kg (187 lb).
Illustration 3 g00611342
3. Remove cylinder head gasket (3).
3/3
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Product: TRACK LOADER
Model: 953C TRACK LOADER 2ZN
Configuration: 953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i04147334
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4876 Lubricant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the cylinder head, refer to Guideline For Reusable
Parts And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114,
3116, and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
1. Thoroughly clean the mating surfaces of the cylinder head and the cylinder block.
1/5
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00611342
Typical example
2. Install a new cylinder head gasket (3) .
Note: For information on the cylinder head gasket for 3116 engines, refer to Special
Instruction, SEHS9395, "3116 Cylinder Head Gasket Usage".
Illustration 2 g01007597
Typical example
Note: To avoid damage to the cylinder head gasket, use guide bolts of an appropriate size to
install the cylinder head.
3. Attach a suitable lifting device to the cylinder head. Position the cylinder head assembly
onto the dowels in the cylinder block. Lower the cylinder head onto the cylinder block.
2/5
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 3 g00654709
4. Inspect the condition of cylinder head bolts (1) and (2) . For information on the reusability
of the bolts, refer to Guideline For Reusable Parts And Salvage Operations, SEBF8301,
"Inspection and Reuse of Critical Fasteners Used in All Engines". Replace cylinder head
bolts (1) and (2) , if necessary.
5. Lubricate cylinder head bolts (1) and (2) and both sides of the washers with Tooling (A) .
Install cylinder head bolts (1) and (2) . Follow Step 6 for the correct tightening procedure.
Illustration 4 g00641677
3114 Cylinder head
3/5
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 5 g00611358
6. Tighten the cylinder head bolts according to the following procedure:
7. Tighten bolts (1) through bolt (14) in a numerical sequence to a torque of 300 ± 15 N·m
(221 ± 11 lb ft).
8. Loosen bolts (1) through bolt (14) to a torque of 0 N·m.
9. Tighten bolts (1) through bolt (14) again in a numerical sequence to a torque of 130 ± 15
N·m (96 ± 11 lb ft).
10. Retighten bolts (1) through bolt (14) again in a numerical sequence to a torque of 130 ± 15
N·m (96 ± 11 lb ft).
11. Turn bolts (1) through bolt (14) by numerical sequence an additional 90° (1/4 turn).
12. Tighten bolt (15) through bolt (20) in a numerical sequence to a torque of 55 ± 7 N·m (41 ±
5 lb ft).
End By:
a. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
b. Install the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold - Install".
c. Install the water temperature regulator housing. Refer to Disassembly and Assembly,
"Water Temperature Regulator Housing- Remove and Install".
d. Install the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Install".
e. Install the fuel control linkage. Refer to Disassembly and Assembly, "Fuel Injection Control
Linkage - Install".
f. Install the governor. Refer to Disassembly and Assembly, "Governor - Install".
g. Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove
and Install".
4/5
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Product: TRACK LOADER
Model: 953C TRACK LOADER 2ZN
Configuration: 953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930413
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/4
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Dispose of all fluids according to local regulations and mandates.
Note: For information on reusability of components of the lifter group, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8264, "Camshaft Roller Followers Used in 3114
and 3116 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8067,
"Slipper Followers and Camshaft Roller Followers".
Illustration 1 g00747310
1. Remove bolts (1) from cover (2).
2. Carefully remove cover (2) and the gasket.
Note: It may be necessary to remove the governor in order to remove the cover at the front
of the engine.
Illustration 2 g00629677
3. Remove bolts (4), lifter shaft (5), and lifters (3) from cover (2).
Installation Procedure
2/4
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of components of the lifter group, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8264, "Camshaft Roller Followers Used in 3114
and 3116 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8067,
"Slipper Followers and Camshaft Roller Followers".
Illustration 3 g00629677
1. Position lifters (3) and lifter shaft (5) on cover (2). Install bolts (4).
Illustration 4 g00747310
2. Position the gasket and cover (2) on the engine.
3. Install bolts (1) in cover (2).
End By:
3/4
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. a. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
4/4
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Product: TRACK LOADER
Model: 953C TRACK LOADER 2ZN
Configuration: 953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930426
Camshaft - Remove
SMCS - 1210-011
Removal Procedure
Start By:
a. Remove the governor. Refer to Disassembly and Assembly, "Governor - Remove".
b. Remove the side covers. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
c. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: For information on reusability of the camshaft, refer to Guideline For Reusable Parts And
Salvage Operations, SEBF8097, "Camshaft Measurement", Guideline For Reusable Parts And
Salvage Operations, SEBF8146, "Visual Inspection of Camshafts", and Guideline For Reusable
Parts And Salvage Operations, SEBF8251, "Specifications for Measurement of Camshafts in
3114/3116 Engines". For information on reusability of the camshaft gear, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
Note: The air compressor was removed in order to accommodate the engine repair stand.
Note: It is not necessary to remove the cylinder head for removal of the camshaft.
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. Install the timing
bolt in the flywheel. This is for timing during installation.
Illustration 1 g01007643
Typical example
2. Ensure that timing mark (1) on the camshaft gear is aligned with timing mark (2) on the
idler gear.
2/3
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01007645
3. Remove bolts (4) and camshaft retainer plate (6).
4. Remove camshaft gear (5) and camshaft (3) from the cylinder block.
3/3
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Product: TRACK LOADER
Model: 953C TRACK LOADER 2ZN
Configuration: 953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01936378
Camshaft - Install
SMCS - 1210-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of the camshaft, refer to Guideline For Reusable Parts And
Salvage Operations, SEBF8097, "Camshaft Measurement", Guideline For Reusable Parts And
Salvage Operations, SEBF8146, "Visual Inspection of Camshafts", and Guideline For Reusable
Parts And Salvage Operations, SEBF8251, "Specifications for Measurement of Camshafts in
3114/3116 Engines". For information on reusability of the camshaft gear, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
1. Lubricate the camshaft and the camshaft bearings with clean engine oil.
1/3
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g01007645
2. Carefully install camshaft (3) and camshaft gear (5) in the engine.
NOTICE
When installing the camshaft, make sure the number one cylinder is at
top center of the compression stroke with the timing bolt installed in
the flywheel. The camshaft timing is very important. The timing mark
on the camshaft drive gear must line up with the timing mark on the
idler gear. Refer to the Specifications Manual for more information.
Illustration 2 g01007643
Typical example
3. Ensure that timing mark (1) on the camshaft gear is aligned with timing mark (2) on the
idler gear.
2/3
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 4. Install camshaft retainer plate (6) and bolts (4).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
b. Install the side cover. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
c. Install the governor. Refer to Disassembly and Assembly, "Governor - Install".
3/3
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Product: TRACK LOADER
Model: 953C TRACK LOADER 2ZN
Configuration: 953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01171077
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
Note: For information on reusability of the camshaft gear, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
1. Wrap the camshaft with a protective covering in order to prevent damage to the camshaft.
Illustration 1 g00611152
NOTICE
1/2
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Do not allow the camshaft to fall to the floor when pressing it from the
drive gear. Also make sure that the camshaft lobes do not catch on the
press plates.
2. Place the camshaft and camshaft gear (1) in a suitable press. Press the camshaft from
camshaft gear (1).
Installation Procedure
Note: For information on reusability of the camshaft gear, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
Illustration 2 g00611152
1. Heat the camshaft gear to a maximum temperature of 315 °C (600 °F).
2. Align the key in the camshaft with the groove (keyway) in the camshaft gear.
3. Install the camshaft gear on the end of the camshaft.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
2/2
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Product: TRACK LOADER
Model: 953C TRACK LOADER 2ZN
Configuration: 953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02183087
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Note the oil hole orientation in each camshaft bearing prior to removal for assembly
purposes.
1. Use Tooling (A) to remove the camshaft bearings from the cylinder block.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g01104579
1. Use Tooling (A) to install all of the camshaft bearings except for the front bearing. Orient
oil hole (1) in each bearing so that oil hole (1) is located at the top of the bore.
2. Use Tooling (A) to install the front camshaft bearing. Align oil hole (1) in the front
camshaft bearing with the oil hole in the cylinder block. Locate joint (2) in the front
camshaft bearing in the proper position.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
4/4
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Product: TRACK LOADER
Model: 953C TRACK LOADER 2ZN
Configuration: 953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01572486
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g00596538
Note: Drain engine oil into a suitable container for disposal.
1. Remove bolts (1) and the washers that hold engine oil pan (2) to the cylinder block.
2. Remove engine oil pan (2) and the gasket. Use a rubber mallet to tap lightly on engine oil
pan (2) if it is necessary.
Note: Do not pry on the engine oil pan.
Installation Procedure
1. Clean the mating surfaces of the engine oil pan and the cylinder block.
Note: Do not put liquid gasket material on the oil pan gasket or on the gasket surface of the
engine oil pan.
2. Put the gasket and the engine oil pan (2) in position on the cylinder block. Install bolts (1)
and washers.
2/3
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 2 g00596576
Typical drawing (6 cylinder engine)
3. Tighten four bolts (3). Start with bolt (4) and tighten the remaining bolts in a
counterclockwise sequence.
4. Tighten bolts to a torque of 31 ± 3 N·m (23 ± 2 lb ft).
5. Fill the crankcase with engine oil to the proper level. Refer to Operation and Maintenance
Manual, "Refill Capacities".
3/3
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Product: TRACK LOADER
Model: 953C TRACK LOADER 2ZN
Configuration: 953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930590
Engine Balancer Shaft - Remove and Install
SMCS - 1220-010-JF
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/3
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
29. Dispose of all fluids according to local regulations and mandates.
Note: The Balancer shafts are used on the 3114 Engines.
Illustration 1 g00596194
314 engine
1. Remove oil tube assembly (1).
2. Remove bolts (2) and the washers that hold the balancer group in position.
3. Remove the balancer group and the engine oil pump as a unit.
Installation Procedure
Illustration 2 g00596364
2/3
953C Track-Type Loader Hydrostatic Drive 2ZN01750-UP (MACHINE) POWERED ...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...