The document provides instructions for removing and installing the cylinder head on a Caterpillar 3126 engine. It describes removing components like the fuel filter base, governor, and manifolds before removing the cylinder head bolts and gasket. For installation, it details cleaning surfaces, installing a new gasket, lubricating and tightening the bolts in a specific sequence while applying proper torque values. The instructions are part of a service repair manual for a Caterpillar 938G wheel loader.
This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel control linkage, unit injectors, water temperature regulator housing, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for cleaning surfaces, installing a new cylinder head gasket, positioning the cylinder head, and tightening the bolts in a specific sequence and torque. Reinstalled components are also listed.
This document provides instructions for removing and installing camshaft bearings on a 3054 engine. It begins by listing the required tools and instructing the user to first remove the camshaft. It then describes using a camshaft bearing tool to press out the old bearings and press in the new ones. The user is advised to clean and lubricate all parts before installation. Finally, it notes to reinstall the camshaft and any other removed components once the bearings are replaced. The full document provides detailed step-by-step instructions and illustrations for completing this maintenance procedure.
This document provides instructions for disassembling and assembling the recoil spring assembly of a 320 Excavator. It describes:
1) Using a specialized recoil spring bench tool and hydraulic cylinder to safely compress the recoil spring assembly and remove/install parts.
2) The 16 step procedure for disassembly, including removing the retaining nut and separating spring components.
3) The 14 step procedure for assembly, including verifying spring length, applying lubricant, and reinstalling retaining components.
Safety is emphasized, as the spring exerts several tons of force and parts could come apart with injury. Precise tool setup and slow, careful compression/release of the spring is required.
Caterpillar cat 320 e l excavator (prefix ree) service repair manual (ree0000...udfujjsejkkem
This document provides instructions for removing and installing the front gear group on a 320E L excavator with a C6.6 engine. The procedure includes using various tools to lock the crankshaft, camshaft, and fuel injection pump in position before removing gears. Alignment marks should be made on the gears. Cleaning and inspecting components is specified before installing the gears back in their original alignment. Various torque specifications are provided for tightening bolts.
CASE 721F TIER 4 WHEEL LOADER Service Repair Manualjksemd dysjekmdm
This is the Highly Detailed factory service repair manual for theCASE 721F TIER 4 WHEEL LOADER, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.CASE 721F TIER 4 WHEEL LOADER Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
Introduction
Engine
Transmission
Four-Wheel Drive (4WD) System
Front Axle System
Rear Axle System
Brakes and Controls
Hydraulic Systems
Steering
Wheels
Cab Climate Control
Electrical System
Platform, Cab, Bodywork, and Decals
Special Tool Index
Electrical Schematic
Hydraulic Schematic – 621F
Hydraulic Schematic – 721F
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveCASE 721F TIER 4 WHEEL LOADER Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
Caterpillar cat 312 c excavator (prefix fds) service repair manual (fds00301 ...fjsjjekdkme
1. The document provides instructions for removing and installing the front housing of a 312C excavator engine.
2. To remove the front housing, several other components must first be removed, including the alternator, water pump, and crankshaft pulley. Bolts securing the front housing to other parts are then loosened and removed.
3. Installation involves cleaning surfaces, installing new seals if needed, and securing the front housing with bolts to the cylinder block, oil pan, and other parts. Timing gear alignment must also be checked during installation.
Caterpillar cat 320 e lrr excavator (prefix mew) service repair manual (mew00...fujsjfjskekemmem
This document provides instructions for removing and installing the front gear group on a Caterpillar C6.6 engine. The removal procedure involves using tools to lock the crankshaft, camshaft and fuel injection pump in position before removing gears. The installation procedure specifies cleaning and inspecting parts, aligning timing marks on gears, checking clearances and backlash, and locking components before tightening fasteners and returning the valve train to TDC. Proper positioning of gears is important to maintain fuel injection pump timing and avoid piston-to-valve interference.
Caterpillar cat 938 g wheel loader (prefix 9hs) service repair manual (9hs000...fiskkdmmd
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3126 engine. It outlines the necessary tools and steps to remove the cylinder head, including removing bolts and lifting the head off. It describes cleaning surfaces and installing a new gasket before positioning the cylinder head and tightening bolts in a specific sequence. Additional steps are included for removing and installing the lifter group.
This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel control linkage, unit injectors, water temperature regulator housing, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for cleaning surfaces, installing a new cylinder head gasket, positioning the cylinder head, and tightening the bolts in a specific sequence and torque. Reinstalled components are also listed.
This document provides instructions for removing and installing camshaft bearings on a 3054 engine. It begins by listing the required tools and instructing the user to first remove the camshaft. It then describes using a camshaft bearing tool to press out the old bearings and press in the new ones. The user is advised to clean and lubricate all parts before installation. Finally, it notes to reinstall the camshaft and any other removed components once the bearings are replaced. The full document provides detailed step-by-step instructions and illustrations for completing this maintenance procedure.
This document provides instructions for disassembling and assembling the recoil spring assembly of a 320 Excavator. It describes:
1) Using a specialized recoil spring bench tool and hydraulic cylinder to safely compress the recoil spring assembly and remove/install parts.
2) The 16 step procedure for disassembly, including removing the retaining nut and separating spring components.
3) The 14 step procedure for assembly, including verifying spring length, applying lubricant, and reinstalling retaining components.
Safety is emphasized, as the spring exerts several tons of force and parts could come apart with injury. Precise tool setup and slow, careful compression/release of the spring is required.
Caterpillar cat 320 e l excavator (prefix ree) service repair manual (ree0000...udfujjsejkkem
This document provides instructions for removing and installing the front gear group on a 320E L excavator with a C6.6 engine. The procedure includes using various tools to lock the crankshaft, camshaft, and fuel injection pump in position before removing gears. Alignment marks should be made on the gears. Cleaning and inspecting components is specified before installing the gears back in their original alignment. Various torque specifications are provided for tightening bolts.
CASE 721F TIER 4 WHEEL LOADER Service Repair Manualjksemd dysjekmdm
This is the Highly Detailed factory service repair manual for theCASE 721F TIER 4 WHEEL LOADER, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.CASE 721F TIER 4 WHEEL LOADER Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
Introduction
Engine
Transmission
Four-Wheel Drive (4WD) System
Front Axle System
Rear Axle System
Brakes and Controls
Hydraulic Systems
Steering
Wheels
Cab Climate Control
Electrical System
Platform, Cab, Bodywork, and Decals
Special Tool Index
Electrical Schematic
Hydraulic Schematic – 621F
Hydraulic Schematic – 721F
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveCASE 721F TIER 4 WHEEL LOADER Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
Caterpillar cat 312 c excavator (prefix fds) service repair manual (fds00301 ...fjsjjekdkme
1. The document provides instructions for removing and installing the front housing of a 312C excavator engine.
2. To remove the front housing, several other components must first be removed, including the alternator, water pump, and crankshaft pulley. Bolts securing the front housing to other parts are then loosened and removed.
3. Installation involves cleaning surfaces, installing new seals if needed, and securing the front housing with bolts to the cylinder block, oil pan, and other parts. Timing gear alignment must also be checked during installation.
Caterpillar cat 320 e lrr excavator (prefix mew) service repair manual (mew00...fujsjfjskekemmem
This document provides instructions for removing and installing the front gear group on a Caterpillar C6.6 engine. The removal procedure involves using tools to lock the crankshaft, camshaft and fuel injection pump in position before removing gears. The installation procedure specifies cleaning and inspecting parts, aligning timing marks on gears, checking clearances and backlash, and locking components before tightening fasteners and returning the valve train to TDC. Proper positioning of gears is important to maintain fuel injection pump timing and avoid piston-to-valve interference.
Caterpillar cat 938 g wheel loader (prefix 9hs) service repair manual (9hs000...fiskkdmmd
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3126 engine. It outlines the necessary tools and steps to remove the cylinder head, including removing bolts and lifting the head off. It describes cleaning surfaces and installing a new gasket before positioning the cylinder head and tightening bolts in a specific sequence. Additional steps are included for removing and installing the lifter group.
The document provides instructions for removing and installing a cylinder head and camshaft on a Caterpillar 3126 engine. It outlines the necessary steps, which include removing components like the intake manifold, exhaust manifold, and unit injectors prior to removing the cylinder head. Detailed instructions are provided for removing the cylinder head bolts and installing a new gasket. Similar steps are outlined for removing the camshaft, which involves removing covers and turning the crankshaft to top center before removal. Safety notices are included to keep parts clean and contain fluids.
The document provides instructions for removing and installing a camshaft on a Caterpillar 3126 engine. It describes removing components like the governor, side covers, and front cover. It instructs the technician to turn the crankshaft to top center compression for piston 1 and install a timing bolt in the flywheel for installation timing. Guidelines are provided for cleaning parts and containing fluids. Notes discuss checking parts for reusability and that the cylinder head need not be removed for camshaft removal.
The document provides instructions for removing and installing a camshaft on a Caterpillar 3126 engine. It describes removing components like the governor, side covers, and front cover. It instructs the technician to turn the crankshaft to top center compression for piston 1 and install a timing bolt in the flywheel for installation timing. Guidelines are provided for cleaning parts and containing fluids. Notes discuss checking parts for reusability and that the cylinder head need not be removed for camshaft removal.
The document provides instructions for removing and installing a camshaft on a Caterpillar 3126 engine. It describes removing components like the governor, side covers, and front cover. It instructs turning the crankshaft to top center compression for the number 1 piston and installing a timing bolt in the flywheel for installation timing. Removal involves removing retaining bolts and carefully extracting the camshaft. Installation is the reverse process. Guidelines are provided for determining if parts can be reused.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3126 engine. It outlines the necessary tools and steps to remove the cylinder head, which include removing bolts and carefully lifting the head off. It also details how to install a new gasket and reattach the cylinder head, specifying the proper tightening procedure and torque specifications for the bolts. Additionally, it covers removing and installing the lifter group, with illustrations of the components and numbered steps.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3126 engine. It outlines the necessary tools and steps to remove the cylinder head, which include removing other engine components, lifting the head off with bolts, and removing the gasket. For installation, it describes cleaning surfaces, installing a new gasket, positioning and bolting the head in place, and tightening the bolts in a specific sequence and torque. It also lists related components to reinstall after the cylinder head is installed.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3126 engine. It outlines the necessary tools and steps to remove the cylinder head, cylinder head gasket, and install the new cylinder head gasket and cylinder head. Tightening procedures and torque specifications are provided for installing the cylinder head bolts. Additional instructions are provided for removing and installing the lifter group components.
The document provides instructions for removing and installing a cylinder head and camshaft on a Caterpillar 3126 engine. It outlines the necessary steps, which include removing components like the inlet manifold, exhaust manifold, and unit injectors prior to removing the cylinder head. Detailed instructions are provided for removing the cylinder head bolts and installing a new gasket. Similarly, instructions are given for removing covers and gears to access the camshaft, as well as notes on inspection and reuse of parts. Tightening procedures and torque specifications are specified for reinstalling components.
The document provides instructions for removing and installing a cylinder head and camshaft on a Caterpillar 3126 engine. It outlines the necessary steps, which include removing components like the intake manifold, exhaust manifold, and unit injectors prior to removing the cylinder head. Detailed instructions are provided for removing the cylinder head bolts and installing a new gasket. Similarly, instructions are given for removing covers and gears to access the camshaft, as well as notes on inspection and reuse of parts. Precautions are emphasized regarding cleanliness and containing fluids.
Caterpillar cat 938 g wheel loader (prefix 9hs) service repair manual (9hs000...fikkskemdmd
The document provides instructions for removing and installing a camshaft on a Caterpillar 3126 engine. It outlines several preparatory steps needed before camshaft removal, such as removing the governor, side covers, and front cover. The removal procedure instructs turning the crankshaft to top center compression for piston 1 and installing a timing bolt in the flywheel for reinstallation timing. Lifters and the camshaft are then removed from the engine covers. Reinstallation involves reversing the removal steps and precautions to keep parts clean and contain fluids.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3126 engine. It outlines the necessary tools and steps to remove the cylinder head, which include removing bolts and carefully lifting the head off. It also details how to install a new gasket and reattach the cylinder head, specifying the proper tightening procedure and torque specifications for the bolts. Additionally, it covers removing and installing the lifter group, with illustrations of the components and numbered steps.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3126 engine. It outlines the necessary tools and steps to remove the cylinder head, including removing bolts and lifting the head off. It describes cleaning surfaces and installing a new gasket before positioning the cylinder head and tightening bolts in a specific sequence. Additional steps are included for installing related components like manifolds after cylinder head installation.
The document provides instructions for removing and installing a camshaft on a Caterpillar 3126 engine. It describes removing components like the governor, side covers, and front cover. It instructs turning the crankshaft to top center compression for the number 1 piston and installing a timing bolt in the flywheel for installation timing. The removal procedure has three steps: 1) Turn the crankshaft, 2) Install timing bolt, 3) Remove camshaft. Reinstallation follows the reverse order. Guidelines are provided for determining if parts can be reused.
This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel linkage, unit injectors, water temperature regulator, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for installing a new cylinder head gasket and cylinder head, ensuring proper torque is applied to the bolts. Reinstalling the other removed components completes the installation.
Caterpillar cat 325 l excavator (prefix 3 ll) service repair manual (3ll00001...hfjsekekmmd
This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel linkage, unit injectors, water temperature regulator, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for cleaning surfaces, installing a new gasket, positioning the cylinder head, and tightening the bolts in a specific sequence and torque. Reinstalled components are also listed.
This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel linkage, unit injectors, water temperature regulator, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for installing a new cylinder head gasket and cylinder head, ensuring proper torque is applied to the bolts. Reinstalling the other removed components completes the installation.
This document provides instructions for removing and installing a cylinder head on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The removal procedure involves detaching various engine components, lifting the cylinder head off with a tool, and removing the gasket. The installation procedure specifies cleaning surfaces, installing a new gasket, positioning and bolting the cylinder head into place, and tightening the bolts in a specific sequence and torque. The document also provides instructions for removing and installing the lifter group.
Caterpillar cat 325 l excavator (prefix 3 ll) service repair manual (3ll00001...cdfzxs
This document provides instructions for removing and installing a cylinder head on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The removal procedure involves detaching various engine components, lifting the cylinder head off with a tool, and removing the gasket. The installation procedure specifies cleaning surfaces, installing a new gasket, positioning the cylinder head with bolts, and torquing the bolts to the specified settings in multiple steps. The document also provides instructions for removing and installing the lifter group.
This document provides instructions for removing and installing a cylinder head on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The removal procedure involves detaching various engine components, lifting the cylinder head off with a tool, and removing the gasket. The installation procedure specifies cleaning surfaces, installing a new gasket, positioning the cylinder head with bolts, and tightening the bolts in a specific sequence and torque. The document also provides instructions for removing and installing the lifter group.
Caterpillar cat 325 l excavator (prefix 3 ll) service repair manual (3ll00001...jdfjskekmdme
This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel linkage, unit injectors, water temperature regulator, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for installing a new cylinder head gasket and cylinder head, ensuring proper tightening of the bolts.
John deere 40, 44, 51, 52, 60, 67, 70, & 70 a loaders service repair manualfdhjsekdme
This technical manual provides specifications and information for John Deere backhoes, loaders, and attachments. It includes specifications on hydraulic systems, function times, capacities, dimensions, cycle times, and torque values. The manual aims to equip technicians with the information needed to work on and service various John Deere equipment.
John deere 38 inch commercial walk behind mower service repair manualfdhjsekdme
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and safety information. The manual is intended for experienced technicians and covers engine, fuel, electrical, power train, steering, brake, and mower deck systems. Safety messages in the introduction emphasize the importance of following proper safety precautions when working on equipment.
More Related Content
Similar to Caterpillar cat 938 g wheel loader (prefix 9hs) service repair manual (9hs00001 and up)
The document provides instructions for removing and installing a cylinder head and camshaft on a Caterpillar 3126 engine. It outlines the necessary steps, which include removing components like the intake manifold, exhaust manifold, and unit injectors prior to removing the cylinder head. Detailed instructions are provided for removing the cylinder head bolts and installing a new gasket. Similar steps are outlined for removing the camshaft, which involves removing covers and turning the crankshaft to top center before removal. Safety notices are included to keep parts clean and contain fluids.
The document provides instructions for removing and installing a camshaft on a Caterpillar 3126 engine. It describes removing components like the governor, side covers, and front cover. It instructs the technician to turn the crankshaft to top center compression for piston 1 and install a timing bolt in the flywheel for installation timing. Guidelines are provided for cleaning parts and containing fluids. Notes discuss checking parts for reusability and that the cylinder head need not be removed for camshaft removal.
The document provides instructions for removing and installing a camshaft on a Caterpillar 3126 engine. It describes removing components like the governor, side covers, and front cover. It instructs the technician to turn the crankshaft to top center compression for piston 1 and install a timing bolt in the flywheel for installation timing. Guidelines are provided for cleaning parts and containing fluids. Notes discuss checking parts for reusability and that the cylinder head need not be removed for camshaft removal.
The document provides instructions for removing and installing a camshaft on a Caterpillar 3126 engine. It describes removing components like the governor, side covers, and front cover. It instructs turning the crankshaft to top center compression for the number 1 piston and installing a timing bolt in the flywheel for installation timing. Removal involves removing retaining bolts and carefully extracting the camshaft. Installation is the reverse process. Guidelines are provided for determining if parts can be reused.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3126 engine. It outlines the necessary tools and steps to remove the cylinder head, which include removing bolts and carefully lifting the head off. It also details how to install a new gasket and reattach the cylinder head, specifying the proper tightening procedure and torque specifications for the bolts. Additionally, it covers removing and installing the lifter group, with illustrations of the components and numbered steps.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3126 engine. It outlines the necessary tools and steps to remove the cylinder head, which include removing other engine components, lifting the head off with bolts, and removing the gasket. For installation, it describes cleaning surfaces, installing a new gasket, positioning and bolting the head in place, and tightening the bolts in a specific sequence and torque. It also lists related components to reinstall after the cylinder head is installed.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3126 engine. It outlines the necessary tools and steps to remove the cylinder head, cylinder head gasket, and install the new cylinder head gasket and cylinder head. Tightening procedures and torque specifications are provided for installing the cylinder head bolts. Additional instructions are provided for removing and installing the lifter group components.
The document provides instructions for removing and installing a cylinder head and camshaft on a Caterpillar 3126 engine. It outlines the necessary steps, which include removing components like the inlet manifold, exhaust manifold, and unit injectors prior to removing the cylinder head. Detailed instructions are provided for removing the cylinder head bolts and installing a new gasket. Similarly, instructions are given for removing covers and gears to access the camshaft, as well as notes on inspection and reuse of parts. Tightening procedures and torque specifications are specified for reinstalling components.
The document provides instructions for removing and installing a cylinder head and camshaft on a Caterpillar 3126 engine. It outlines the necessary steps, which include removing components like the intake manifold, exhaust manifold, and unit injectors prior to removing the cylinder head. Detailed instructions are provided for removing the cylinder head bolts and installing a new gasket. Similarly, instructions are given for removing covers and gears to access the camshaft, as well as notes on inspection and reuse of parts. Precautions are emphasized regarding cleanliness and containing fluids.
Caterpillar cat 938 g wheel loader (prefix 9hs) service repair manual (9hs000...fikkskemdmd
The document provides instructions for removing and installing a camshaft on a Caterpillar 3126 engine. It outlines several preparatory steps needed before camshaft removal, such as removing the governor, side covers, and front cover. The removal procedure instructs turning the crankshaft to top center compression for piston 1 and installing a timing bolt in the flywheel for reinstallation timing. Lifters and the camshaft are then removed from the engine covers. Reinstallation involves reversing the removal steps and precautions to keep parts clean and contain fluids.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3126 engine. It outlines the necessary tools and steps to remove the cylinder head, which include removing bolts and carefully lifting the head off. It also details how to install a new gasket and reattach the cylinder head, specifying the proper tightening procedure and torque specifications for the bolts. Additionally, it covers removing and installing the lifter group, with illustrations of the components and numbered steps.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3126 engine. It outlines the necessary tools and steps to remove the cylinder head, including removing bolts and lifting the head off. It describes cleaning surfaces and installing a new gasket before positioning the cylinder head and tightening bolts in a specific sequence. Additional steps are included for installing related components like manifolds after cylinder head installation.
The document provides instructions for removing and installing a camshaft on a Caterpillar 3126 engine. It describes removing components like the governor, side covers, and front cover. It instructs turning the crankshaft to top center compression for the number 1 piston and installing a timing bolt in the flywheel for installation timing. The removal procedure has three steps: 1) Turn the crankshaft, 2) Install timing bolt, 3) Remove camshaft. Reinstallation follows the reverse order. Guidelines are provided for determining if parts can be reused.
This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel linkage, unit injectors, water temperature regulator, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for installing a new cylinder head gasket and cylinder head, ensuring proper torque is applied to the bolts. Reinstalling the other removed components completes the installation.
Caterpillar cat 325 l excavator (prefix 3 ll) service repair manual (3ll00001...hfjsekekmmd
This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel linkage, unit injectors, water temperature regulator, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for cleaning surfaces, installing a new gasket, positioning the cylinder head, and tightening the bolts in a specific sequence and torque. Reinstalled components are also listed.
This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel linkage, unit injectors, water temperature regulator, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for installing a new cylinder head gasket and cylinder head, ensuring proper torque is applied to the bolts. Reinstalling the other removed components completes the installation.
This document provides instructions for removing and installing a cylinder head on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The removal procedure involves detaching various engine components, lifting the cylinder head off with a tool, and removing the gasket. The installation procedure specifies cleaning surfaces, installing a new gasket, positioning and bolting the cylinder head into place, and tightening the bolts in a specific sequence and torque. The document also provides instructions for removing and installing the lifter group.
Caterpillar cat 325 l excavator (prefix 3 ll) service repair manual (3ll00001...cdfzxs
This document provides instructions for removing and installing a cylinder head on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The removal procedure involves detaching various engine components, lifting the cylinder head off with a tool, and removing the gasket. The installation procedure specifies cleaning surfaces, installing a new gasket, positioning the cylinder head with bolts, and torquing the bolts to the specified settings in multiple steps. The document also provides instructions for removing and installing the lifter group.
This document provides instructions for removing and installing a cylinder head on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The removal procedure involves detaching various engine components, lifting the cylinder head off with a tool, and removing the gasket. The installation procedure specifies cleaning surfaces, installing a new gasket, positioning the cylinder head with bolts, and tightening the bolts in a specific sequence and torque. The document also provides instructions for removing and installing the lifter group.
Caterpillar cat 325 l excavator (prefix 3 ll) service repair manual (3ll00001...jdfjskekmdme
This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel linkage, unit injectors, water temperature regulator, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for installing a new cylinder head gasket and cylinder head, ensuring proper tightening of the bolts.
Similar to Caterpillar cat 938 g wheel loader (prefix 9hs) service repair manual (9hs00001 and up) (20)
John deere 40, 44, 51, 52, 60, 67, 70, & 70 a loaders service repair manualfdhjsekdme
This technical manual provides specifications and information for John Deere backhoes, loaders, and attachments. It includes specifications on hydraulic systems, function times, capacities, dimensions, cycle times, and torque values. The manual aims to equip technicians with the information needed to work on and service various John Deere equipment.
John deere 38 inch commercial walk behind mower service repair manualfdhjsekdme
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and safety information. The manual is intended for experienced technicians and covers engine, fuel, electrical, power train, steering, brake, and mower deck systems. Safety messages in the introduction emphasize the importance of following proper safety precautions when working on equipment.
John deere 30 inch hydraulic tiller service repair manualfdhjsekdme
This technical manual provides specifications and information for John Deere backhoes, loaders, and attachments. It includes specifications on hydraulic systems, function times, capacities, dimensions, cycle times, and torque values. The manual aims to equip technicians with the information needed to work on and service various John Deere equipment.
John deere 14 sz walk behind mower service repair manualfdhjsekdme
This document contains information related to John Deere walk-behind mowers. It includes:
1. Specifications for various mower models including the 12PB/12PC/12SB, 14PB/14PT/14PZ/14SB, 14SC/14SX/14SE/14ST, and 14SZ.
2. Repair specifications for Briggs & Stratton 2-cycle and 4-cycle engines, Kawasaki 4-cycle engines, and Kansaki 2- and 5-speed transaxles.
3. Safety information related to handling fluids, preventing battery explosions, preparing for emergencies, and preventing acid burns from battery electrolyte.
John deere 14 sx walk behind mower service repair manualfdhjsekdme
This document contains information related to walk-behind mowers manufactured by John Deere, including:
1. Model numbers and specifications for various mower models.
2. Safety warnings and instructions for handling fluids, batteries, and preparing for emergencies.
3. Tables providing repair specifications for engine components, including torque specifications.
The document provides general technical information for technicians servicing John Deere walk-behind mowers, including identifying models, safety practices, and specifications to guide repairs. It begins with safety instructions and then provides specifications and identification information for the different mower models and their components.
John deere 14 st walk behind mower service repair manualfdhjsekdme
This document contains information related to John Deere walk-behind mowers. It includes:
1. Specifications for various mower models including the 12PB/12PC/12SB, 14PB/14PT/14PZ/14SB, 14SC/14SX/14SE/14ST, and 14SZ.
2. Repair specifications for Briggs & Stratton 2-cycle and 4-cycle engines, Kawasaki 4-cycle engines, and Kansaki 2- and 5-speed transaxles.
3. Safety information related to handling fluids, preventing battery explosions, preparing for emergencies, and preventing acid burns from battery electrolyte.
John deere 14 se walk behind mower service repair manualfdhjsekdme
This document contains information related to John Deere walk-behind mowers. It includes:
1. Specifications for various mower models including the 12PB/12PC/12SB, 14PB/14PT/14PZ/14SB, 14SC/14SX/14SE/14ST, and 14SZ.
2. Repair specifications for Briggs & Stratton 2-cycle and 4-cycle engines, Kawasaki 4-cycle engines, and Kansaki 2- and 5-speed transaxles.
3. Safety information related to handling fluids, preventing battery explosions, preparing for emergencies, and preventing acid burns from battery electrolyte.
John deere 14 sc walk behind mower service repair manualfdhjsekdme
This document contains information related to John Deere walk-behind mowers. It includes:
1. Specifications for various mower models including the 12PB/12PC/12SB, 14PB/14PT/14PZ/14SB, 14SC/14SX/14SE/14ST, and 14SZ.
2. Repair specifications for Briggs & Stratton 2-cycle and 4-cycle engines, Kawasaki 4-cycle engines, and Kansaki 2- and 5-speed transaxles.
3. Safety information related to handling fluids, preventing battery explosions, preparing for emergencies, and preventing acid burns from battery electrolyte.
John deere 14 sb walk behind mower service repair manualfdhjsekdme
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications, repair procedures, diagnostics, and testing for various mower components including engines made by Briggs & Stratton and Kawasaki, as well as transmissions. Safety precautions are provided at the beginning relating to handling fluids, preventing battery explosions, preparing for emergencies, and preventing acid burns. The document is organized into sections covering general information, engine repair, fuel/air systems, electrical systems, power trains, and operational tests and adjustments.
John deere 14 pz walk behind mower service repair manualfdhjsekdme
This document contains information related to John Deere walk-behind mowers. It includes:
1. Specifications for various mower models including the 12PB/12PC/12SB, 14PB/14PT/14PZ/14SB, 14SC/14SX/14SE/14ST, and 14SZ.
2. Repair specifications for Briggs & Stratton 2-cycle and 4-cycle engines, Kawasaki 4-cycle engines, and Kansaki 2- and 5-speed transaxles.
3. Safety information related to handling fluids, preventing battery explosions, preparing for emergencies, and preventing acid burns from battery electrolyte.
John deere 14 pt walk behind mower service repair manualfdhjsekdme
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications, repair procedures, diagnostics, and testing for various mower components including engines made by Briggs & Stratton and Kawasaki, as well as transmissions. Safety precautions are provided at the beginning relating to handling fluids, preventing battery explosions, preparing for emergencies, and preventing acid burns. The document is organized into sections covering general information, engine repair, fuel/air systems, electrical systems, power trains, and operational tests and adjustments.
John deere 14 pb walk behind mower service repair manualfdhjsekdme
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications for various mower models, repair specifications for engines and components, information on fuels and lubricants, and locations for identifying serial numbers. The document outlines sections on general information, engine repair, fuel and air systems, electrical systems, power trains, tests and adjustments, and miscellaneous repair items. It provides technicians with the information needed to service, diagnose, and repair the mowers.
John deere 12 sb walk behind mower service repair manualfdhjsekdme
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications for various mower models, repair specifications for engines and components, information on fuels and lubricants, and locations for identifying serial numbers. The document outlines sections on general information, engine repair, fuel and air systems, electrical systems, power trains, tests and adjustments, and miscellaneous repair items. It provides technicians with the information needed to service, diagnose, and repair components.
John deere 12 pc walk behind mower service repair manualfdhjsekdme
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications, repair procedures, diagnostics, and testing for various mower components including engines made by Briggs & Stratton and Kawasaki, as well as transmissions. Safety precautions are provided at the beginning relating to handling fluids, preventing battery explosions, preparing for emergencies, and preventing acid burns. The document is organized into sections covering general information, engine repair, fuel/air systems, electrical systems, power trains, and operational tests/adjustments.
John deere 12 pb walk behind mower service repair manualfdhjsekdme
This document is the technical manual for John Deere 21-inch rear discharge walk-behind rotary mowers. It provides specifications, repair and diagnostic information for the mowers and their components. The manual is divided into sections covering general information, engine repair for different engine types, fuel and air systems, electrical systems, power trains, tests and adjustments, and troubleshooting. It contains detailed instructions and specifications to guide technicians in servicing and repairing the mowers. Model numbers covered include models with Briggs & Stratton 2-cycle and 4-cycle engines as well as Kawasaki 4-cycle engines.
Clark ecg 20 32 genesis series truck service repair manualfdhjsekdme
This document provides instructions for safely maintaining a Clark industrial lift truck. It discusses safety signs and messages, safe maintenance practices, lifting and jacking procedures, towing instructions, and general shop precautions. Key safety points include wearing protective equipment, raising drive wheels off the floor before working, disconnecting batteries, checking for fuel and electrical issues, and only allowing trained personnel to perform maintenance.
Clark ec 120 forklift service repair manualfdhjsekdme
This section provides instructions for safely lifting, jacking and blocking a forklift truck. It describes how to use the upright as a lever to raise just the drive wheels off the floor for service. It also explains how to raise the rear or entire truck using a jack and secure blocking. Safety precautions are emphasized, such as ensuring lifting equipment has adequate capacity and the truck is stable before working on it.
Clark ec 90 forklift service repair manualfdhjsekdme
This section provides instructions for safely lifting, jacking and blocking a forklift truck. It describes how to use the forklift's upright as a lever to raise just the drive wheels off the floor for service. It also provides guidelines for raising the rear or entire truck using lifting equipment with adequate capacity. Safety precautions are outlined, such as ensuring the forklift is on level ground, in neutral with the brakes set before lifting. Defective lifting equipment should not be used.
Clark e357 forklift service repair manualfdhjsekdme
This document is a service manual for Clark lift trucks. It provides maintenance and repair procedures for technicians. The manual contains sections on safety practices, planned maintenance schedules, component inspections and repairs, specifications, and schematics. Regular maintenance is important to keep lift trucks in safe operating condition. Only trained personnel should perform repairs following the manufacturer's recommended procedures.
Clark dpx 55 forklift service repair manualfdhjsekdme
The document provides instructions for removing and installing a transmission on a Clark forklift. It describes disconnecting all transmission connections, draining the oil, removing mounting bolts and lowering the transmission out of the truck using lifting equipment. Installation involves bolting the torque converter to the engine flywheel through an access port, then lifting the transmission into place and reconnecting all lines and linkages. Safety precautions are noted such as securing the truck before starting and keeping inspection openings covered.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 938G WHEEL LOADER 9HS
Configuration: 938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01935828
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
a. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
b. Remove the governor. Refer to Disassembly and Assembly, "Governor - Remove".
c. Remove the fuel control linkage. Refer to Disassembly and Assembly, "Fuel Injection
Control Linkage - Remove".
d. Remove the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
e. Remove the water temperature regulator housing. Refer to Disassembly and Assembly,
"Water Temperature Regulator Housing - Remove and Install".
f. Remove the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold -
Remove".
g. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: For information on the reusability of the cylinder head, refer to Guideline For Reusable
Parts And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114,
3116, and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 1 g01007597
Typical example
1. Attach a suitable lifting device to the cylinder head.
2/3938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00654709
2. Remove bolts (1) and (2) that hold the cylinder head to the cylinder block. Carefully remove
the cylinder head from the cylinder block. The cylinder head for the 3116 engine weighs
approximately 85 kg (187 lb).
Illustration 3 g00611342
3. Remove cylinder head gasket (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 15 22:46:38 UTC+0800 2020
3/3938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 938G WHEEL LOADER 9HS
Configuration: 938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i04147334
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4876 Lubricant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the cylinder head, refer to Guideline For Reusable
Parts And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114,
3116, and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
1. Thoroughly clean the mating surfaces of the cylinder head and the cylinder block.
1/5938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00611342
Typical example
2. Install a new cylinder head gasket (3) .
Note: For information on the cylinder head gasket for 3116 engines, refer to Special
Instruction, SEHS9395, "3116 Cylinder Head Gasket Usage".
Illustration 2 g01007597
Typical example
Note: To avoid damage to the cylinder head gasket, use guide bolts of an appropriate size to
install the cylinder head.
3. Attach a suitable lifting device to the cylinder head. Position the cylinder head assembly
onto the dowels in the cylinder block. Lower the cylinder head onto the cylinder block.
2/5938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 3 g00654709
4. Inspect the condition of cylinder head bolts (1) and (2) . For information on the reusability
of the bolts, refer to Guideline For Reusable Parts And Salvage Operations, SEBF8301,
"Inspection and Reuse of Critical Fasteners Used in All Engines". Replace cylinder head
bolts (1) and (2) , if necessary.
5. Lubricate cylinder head bolts (1) and (2) and both sides of the washers with Tooling (A) .
Install cylinder head bolts (1) and (2) . Follow Step 6 for the correct tightening procedure.
Illustration 4 g00641677
3114 Cylinder head
3/5938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 5 g00611358
6. Tighten the cylinder head bolts according to the following procedure:
7. Tighten bolts (1) through bolt (14) in a numerical sequence to a torque of 300 ± 15 N·m
(221 ± 11 lb ft).
8. Loosen bolts (1) through bolt (14) to a torque of 0 N·m.
9. Tighten bolts (1) through bolt (14) again in a numerical sequence to a torque of 130 ± 15
N·m (96 ± 11 lb ft).
10. Retighten bolts (1) through bolt (14) again in a numerical sequence to a torque of 130 ± 15
N·m (96 ± 11 lb ft).
11. Turn bolts (1) through bolt (14) by numerical sequence an additional 90° (1/4 turn).
12. Tighten bolt (15) through bolt (20) in a numerical sequence to a torque of 55 ± 7 N·m (41 ±
5 lb ft).
End By:
a. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
b. Install the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold - Install".
c. Install the water temperature regulator housing. Refer to Disassembly and Assembly,
"Water Temperature Regulator Housing- Remove and Install".
d. Install the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Install".
e. Install the fuel control linkage. Refer to Disassembly and Assembly, "Fuel Injection Control
Linkage - Install".
f. Install the governor. Refer to Disassembly and Assembly, "Governor - Install".
g. Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove
and Install".
4/5938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 938G WHEEL LOADER 9HS
Configuration: 938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930413
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/4938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Dispose of all fluids according to local regulations and mandates.
Note: For information on reusability of components of the lifter group, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8264, "Camshaft Roller Followers Used in 3114
and 3116 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8067,
"Slipper Followers and Camshaft Roller Followers".
Illustration 1 g00747310
1. Remove bolts (1) from cover (2).
2. Carefully remove cover (2) and the gasket.
Note: It may be necessary to remove the governor in order to remove the cover at the front
of the engine.
Illustration 2 g00629677
3. Remove bolts (4), lifter shaft (5), and lifters (3) from cover (2).
Installation Procedure
2/4938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of components of the lifter group, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8264, "Camshaft Roller Followers Used in 3114
and 3116 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8067,
"Slipper Followers and Camshaft Roller Followers".
Illustration 3 g00629677
1. Position lifters (3) and lifter shaft (5) on cover (2). Install bolts (4).
Illustration 4 g00747310
2. Position the gasket and cover (2) on the engine.
3. Install bolts (1) in cover (2).
End By:
3/4938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. a. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 15 22:48:29 UTC+0800 2020
4/4938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 938G WHEEL LOADER 9HS
Configuration: 938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930426
Camshaft - Remove
SMCS - 1210-011
Removal Procedure
Start By:
a. Remove the governor. Refer to Disassembly and Assembly, "Governor - Remove".
b. Remove the side covers. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
c. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: For information on reusability of the camshaft, refer to Guideline For Reusable Parts And
Salvage Operations, SEBF8097, "Camshaft Measurement", Guideline For Reusable Parts And
Salvage Operations, SEBF8146, "Visual Inspection of Camshafts", and Guideline For Reusable
Parts And Salvage Operations, SEBF8251, "Specifications for Measurement of Camshafts in
3114/3116 Engines". For information on reusability of the camshaft gear, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
Note: The air compressor was removed in order to accommodate the engine repair stand.
Note: It is not necessary to remove the cylinder head for removal of the camshaft.
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. Install the timing
bolt in the flywheel. This is for timing during installation.
Illustration 1 g01007643
Typical example
2. Ensure that timing mark (1) on the camshaft gear is aligned with timing mark (2) on the
idler gear.
2/3938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g01007645
3. Remove bolts (4) and camshaft retainer plate (6).
4. Remove camshaft gear (5) and camshaft (3) from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 15 22:49:25 UTC+0800 2020
3/3938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 938G WHEEL LOADER 9HS
Configuration: 938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01936378
Camshaft - Install
SMCS - 1210-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of the camshaft, refer to Guideline For Reusable Parts And
Salvage Operations, SEBF8097, "Camshaft Measurement", Guideline For Reusable Parts And
Salvage Operations, SEBF8146, "Visual Inspection of Camshafts", and Guideline For Reusable
Parts And Salvage Operations, SEBF8251, "Specifications for Measurement of Camshafts in
3114/3116 Engines". For information on reusability of the camshaft gear, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
1. Lubricate the camshaft and the camshaft bearings with clean engine oil.
1/3938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01007645
2. Carefully install camshaft (3) and camshaft gear (5) in the engine.
NOTICE
When installing the camshaft, make sure the number one cylinder is at
top center of the compression stroke with the timing bolt installed in
the flywheel. The camshaft timing is very important. The timing mark
on the camshaft drive gear must line up with the timing mark on the
idler gear. Refer to the Specifications Manual for more information.
Illustration 2 g01007643
Typical example
3. Ensure that timing mark (1) on the camshaft gear is aligned with timing mark (2) on the
idler gear.
2/3938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. 4. Install camshaft retainer plate (6) and bolts (4).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
b. Install the side cover. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
c. Install the governor. Refer to Disassembly and Assembly, "Governor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 15 22:50:21 UTC+0800 2020
3/3938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 938G WHEEL LOADER 9HS
Configuration: 938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01171077
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
Note: For information on reusability of the camshaft gear, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
1. Wrap the camshaft with a protective covering in order to prevent damage to the camshaft.
Illustration 1 g00611152
NOTICE
1/2938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Do not allow the camshaft to fall to the floor when pressing it from the
drive gear. Also make sure that the camshaft lobes do not catch on the
press plates.
2. Place the camshaft and camshaft gear (1) in a suitable press. Press the camshaft from
camshaft gear (1).
Installation Procedure
Note: For information on reusability of the camshaft gear, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
Illustration 2 g00611152
1. Heat the camshaft gear to a maximum temperature of 315 °C (600 °F).
2. Align the key in the camshaft with the groove (keyway) in the camshaft gear.
3. Install the camshaft gear on the end of the camshaft.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 15 22:51:16 UTC+0800 2020
2/2938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 938G WHEEL LOADER 9HS
Configuration: 938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02183087
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4938G WHEEL LOADER 9HS00001-UP (MACHINE) POWERED BY 3126 Engine(...
2020/3/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...