This service repair manual provides instructions for connecting the loader frame and rear frame of a 930H wheel loader. It outlines 54 steps to reconnect components like bearings, seals, pins and hoses. Tools and safety precautions are listed. The manual also describes separating and reconnecting the steering frame lock between the front and rear frames.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 930H WHEEL LOADER DHC
Configuration: 928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
924H, 924HZ, 928HZ and 930H Wheel Loaders Machine Systems
Media Number -KENR9440-02 Publication Date -01/08/2012 Date Updated -01/08/2012
i07528732
Loader Frame and Rear Frame - Connect
SMCS - 7051-077; 7054-077
S/N - DHC1-UP
S/N - HXC1-UP
Connection Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1863 Retaining Ring Pliers 1
B
284-5122 Stand 1
8S-7611 Tube 1
8S-7615 Pin 1
C 8T-5255 Hydraulic Jack 1
D 417-1324 Repair Stand Set 2
H 189-0412 Shackle 2
J 5P-0960 Grease Cartridge 1
K 1P-0510 Driver Gp 1
L - Loctite C5A Copper Anti-Seize -
M 1P-0481 Drive Plate 2
N 1P-0495 Drive Plate 2
P
1B-2716 Bolt 1
6V-8185 Nut 1
1/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 En...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, PERJ1017, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Note: Apply Tooling (J) to all seals before installation. Lubricate all pin bores and all pins with Tooling
(L) before installation of the pins.
Illustration 1 g01118635
Note: Reference Illustration 4 for seal orientation.
1. Use Tooling (K) to install lip seal (39) into upper cap (35).
Illustration 2 g01118634
Note: Reference Illustration 4 for seal orientation.
2. Use Tooling (K) to install lip seal (38) into lower cap (37).
2/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 En...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01120311
3. Position lower cap (37).
4. Install three bolts (34) in equal spacing.
Illustration 4 g06351214
Lower Hitch
5. Lower the temperature of bearing cup (42).
6. Install bearing cup (42) so that bearing cup (42) contacts the lower cap.
7. Coat bearing cones (41) and (43) with oil.
8. Install bearing cones (41) and (43).
9. Lower the temperature of bearing cup (40) and install bearing cup (40).
3/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 En...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01120311
10. Remove bolts (34) and lower cap (37).
Illustration 6 g01120313
11. Install 1.5 mm (0.06 inch) of shims (36).
Illustration 7 g01120315
12. Install upper cap (35), lower cap (37), and three of bolts (34), as shown.
13. Use Tooling (M) and Tooling (P) to check the rolling torques of the two bearing assemblies.
14. Add or remove shims (36) until the rolling torque of the bearing assemblies are between
1.7 N·m to 5.6 N·m (15 lb in to 50 lb in).
4/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 En...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g01118632
15. Install remaining bolts (34) onto upper cap (35).
Illustration 9 g01118630
Note: Reference Illustration 12 for seal orientation.
16. Use Tooling (K) to install lip seal (33) into upper cap (28).
Illustration 10 g01118528
Note: Reference Illustration 12 for seal orientation.
17. Use Tooling (K) to install lip seal (32) into lower cap (30).
5/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 En...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g01120480
18. Position lower cap (30).
19. Install three bolts (27).
Illustration 12 g03741654
Upper Hitch
20. Lower the temperature of bearing cup (46).
21. Install bearing cup (46) so that bearing cup (46) contacts the lower cap.
22. Completely coat bearing cones (44) and (47) with oil.
23. Install bearing cones (44) and (47).
24. Lower the temperature of bearing cup (45) and install bearing cup (45).
6/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 En...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g01120480
25. Remove bolts (27) and lower cap (30).
Illustration 14 g01121070
26. Install 2.0 mm (0.08 inch) of shims (29).
Illustration 15 g01121074
27. Install upper cap (28), lower cap (30), and three of bolts (27), as shown.
28. Use Tooling (N) and Tooling (P) to check the rolling torques of the two bearings.
29. Add or remove shims (29) until the rolling torque of each bearing is between 2.8 N·m to 11.2 N·m
(25 lb in to 99 lb in).
7/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 En...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g01118522
32. Use a suitable towing device and a suitable lifting device to reposition frame assembly (18).
Illustration 19 g01131984
9/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 En...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 33. Position frame assembly (18). Install pin assembly (19). Install bolt (20).
Illustration 20 g01118430
34. Use Tooling (B) to support the rear end of the machine. Use Tooling (C) to adjust the alignment of
the frames.
Illustration 21 g06187596
Upper Hitch
35. Lower the temperature of pin assembly (25). Install pin assembly (25) into the bore of the upper
hitch.
10/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 ...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 22 g01131940
36. Install plate (22) and bolts (23), as shown.
Illustration 23 g01131945
37. Use a feeler gauge to measure the gap between the flange of pin assembly (25) and the top of the
hitch. Record the measurement.
Illustration 24 g01131940
38. Remove plate (22) and bolts (23).
Illustration 25 g01131952
39. Install shims (26) of the thickness that was recorded in Step 37 under pin assembly (25).
11/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 ...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g01131957
40. Install bolts (24) to pin assembly (25).
Illustration 27 g01131960
41. Measure the gap between the bottom of pin assembly (25) and the bottom of the hitch. Record the
measurement.
12/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 ...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 28 g01118514
42. Install shims (21) with a thickness that is 0.25 mm (0.010 inch) less than the measured gap from Step
41.
43. Install plate (22) and bolts (23).
Illustration 29 g01404160
13/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 ...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 30 g01118425
44. Position steering metering unit (17). Install bolts (16) onto both sides of the steering column.
Position the floor mats into the cab.
Illustration 31 g01118422
45. Reposition bracket (15).
14/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 ...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 32 g01118420
46. Connect hose assembly (14) and install all mounting hardware.
Illustration 33 g01118417
15/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 ...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 47. Reposition harness assembly (13). Install all mounting hardware onto harness assembly (13).
Connect harness assemblies (11) and (12). Connect harness assembly (10) onto both sides of the
machine.
Illustration 34 g01118201
48. Connect hose assemblies (8) and all mounting hardware. Connect hose assembly (9).
16/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 ...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 35 g01118198
49. Position hose assemblies (6) and hose assemblies (7). Connect hose assemblies (6) and hose
assemblies (7).
Illustration 36 g01118197
50. Install pin (5). Use Tooling (A) to install retaining ring (4).
51. Repeat Step 50 to install the pin into the steering cylinder on the other side of the machine.
17/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 ...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 39 g01118191
54. Remove the suitable blocking from bucket (1).
55. Fill the hydraulic oil tank. The hydraulic tank capacity is approximately 73 L (19.3 US gal). Refer to
Operation and Maintenance Manual for the proper procedure.
End By:
a. Install the center drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Center) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 24 10:51:08 UTC+0800 2020
19/19
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 ...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 930H WHEEL LOADER DHC
Configuration: 928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
924H, 924Hz, 928Hz and 930H Wheel Loaders Machine Systems
Media Number -KENR7617-01 Publication Date -01/04/2010 Date Updated -21/04/2010
i02748684
Steering Frame Lock - Separate and Connect
SMCS - 7506-029
Connection Procedure
Personal injury or death can result from machine articulation or
movement.
Machine frames can move and a person can be crushed.
Connect the steering frame lock link between the front and rear frames
before working on machine. Secure clevis pin with locking pin.
Before operating the machine, fasten the steering frame lock link into
the stored position and secure the clevis pin with locking pin.
Failure to lock into the stored position before operating can result in loss
of steering.
1/3
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 En...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g01377068
1. Remove hitch pin (2) from pin (1).
Illustration 2 g01377066
2. Move steering frame lock (3) in position to the front frame. Install pin (1) and hitch pin (2).
Note: To align the pin bores, move the front loader frame.
Separation Procedure
Personal injury or death can result from machine articulation or
movement.
Machine frames can move and a person can be crushed.
Connect the steering frame lock link between the front and rear frames
before working on machine. Secure clevis pin with locking pin.
Before operating the machine, fasten the steering frame lock link into
the stored position and secure the clevis pin with locking pin.
2/3
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 En...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Failure to lock into the stored position before operating can result in loss
of steering.
Illustration 3 g01377066
1. Remove pin (1) and hitch pin (2). Move steering frame lock (3) to the storage position.
Illustration 4 g01377068
2. Install pin (1) and hitch pin (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 24 11:00:52 UTC+0800 2020
3/3
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 En...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 930H WHEEL LOADER DHC
Configuration: 928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
924H, 924Hz, 928Hz and 930H Wheel Loaders Machine Systems
Media Number -KENR7617-01 Publication Date -01/04/2010 Date Updated -21/04/2010
i05079160
System Pressure - Release
SMCS - 4250-553-PX; 4300-553-PX; 5050-553-PX
Machine Preparation
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Escaping fluid under pressure, even a pinhole size leak, can penetrate
body tissue, causing serious injury, and possible death. If fluid is
injected into your skin, it must be treated immediately by a doctor
familiar with this type of injury.
Always use a board or cardboard when checking for a leak.
1/4
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 En...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Refer to Testing and Adjusting, "Machine Preparation for Troubleshooting" for the machine
that is being serviced before performing the following procedure.
Release System Pressure
1. Move the machine to a location that is smooth, level, and hard. The location should also be
dry and free of debris. Stop the engine.
2. Permit only one operator on the machine. All other personnel should be kept away from the
machine.
3. If the machine is equipped with a ride control system, move the ride control switch to the
Manual position.
Illustration 1 g02009358
2/4
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 En...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 4. Position the bucket or work tool just above the ground at a slight downward angle. This
position will ensure that the head end of the lift cylinders is pressurized.
5. Engage the parking brake.
6. Turn the engine start switch to the OFF position.
7. When the engine has stopped, turn the engine start switch back to the ON position so the
pilot oil can reach the main valve.
8. Move the implement lockout switch to the UNLOCKED position.
9. Move the lift control lever to the FLOAT position and the tilt control lever to the TILT
BACK position at the same time. This action allows the bucket or the work tool to tilt back
while the boom is lowered.
The bottom of the bucket or the work tool should rest flat on the ground. The weight of the
linkage should be supported by the ground. The pressure from the head end of the lift
cylinders and from the ride control accumulator is now vented to the hydraulic tank.
10. When the bucket or the work tool has settled to the ground, move both control levers to the
HOLD position. Then, repeatedly cycle the control levers through all positions in order to
purge any remaining pressure from the implement hydraulic system.
11. Turn the steering wheel several times in both directions in order to relieve the pressure in
the steering system. To release the pressure from steering cylinders on machines equipped
with joystick steering, the machine must not be operated for a minimum of 10 minutes. 10
minutes will allow sufficient time for the pressure in the steering system to dissipate.
12. Turn the engine start switch to the OFF position.
13. Depress the brake pedal repeatedly. This step will relieve any pressure that may be present
in the braking system.
14. Push in the plunger for the hydraulic tank breaker relief valve until all pressure is released.
Note: If the machine is not equipped with a hydraulic tank breaker relief valve, remove the
hydraulic tank cap slowly to relieve tank pressure.
Dead Electronics
1. If the electronics fail, all stored hydraulic oil pressure may not be relieved. The following
precautions should be taken.
2. Turn the engine OFF.
3. The machine should be secured with a lockout.
4. Use the appropriate stand or blocks to prevent undesired drift of implements.
5. Barriers should be used in order to prevent personnel from entering areas that implement
drift or movement could be hazardous.
3/4
928HZ 930H Wheel Loader DHC00001-04199 (MACHINE) POWERED BY C6.6 En...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...