This document provides instructions for connecting the frame of a 950H wheel loader. It involves assembling top and lower hitch bearings using various tools, then lifting and connecting the loader frame to the rear frame. Precise alignment of parts is important. The process includes installing pins, spacers, and plates before measuring clearances and torquing bolts to specifications.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950H WHEEL LOADER JLX
Configuration: 950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine
Disassembly and Assembly
950H and 962H Wheel Loaders Machine Systems
Media Number -UENR1619-00 Publication Date -01/12/2012 Date Updated -04/12/2012
i05021371
Loader Frame to Rear Frame - Connect
SMCS - 7051-077; 7054-077
Connection Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-7536 Stand 2
277-7200 Electric Hydraulic Pump Gp 1
B 138-7574 Link Bracket 2
G FT-2826 Lower Plate Gp 1
H 1P-0520 Driver Gp 1
J FT-2825 Upper Plate Gp 1
K - Loctite C5-A Copper Anti-Seize -
Note: The following steps are for the assembly of the top hitch bearings.
1/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g01192969
Typical Example
1. Position lower cap (22) on the upper frame. Hold the lower cap in place with three bolts
(20) that are equally spaced. Make sure that the lower cap is seated firmly against the upper
frame.
2. Apply Tooling (K) to the bores.
Illustration 2 g01192972
3. Lower the temperature of lower bearing cup (35) to −50° ± 5°C (−58° ± 9°F).
4. Install lower bearing cup (35). Use Tooling (H) in order to ensure that bearing cup (35)
contacts lower cap (22) .
2/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 3 g01192974
5. Apply clean oil to bearing cone (36). Install bearing cone (36) in the correct position, as
shown.
Illustration 4 g01192977
6. Apply clean oil to bearing cone (37). Install bearing cone (37) in the correct position, as
shown.
Illustration 5 g01192978
3/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 7. Lower the temperature of upper bearing cup (38) to −50° ± 5°C (−58° ± 9°F).
8. Install upper bearing cup (38). Use Tooling (H) in order to ensure that bearing cup (38)
lightly contacts the bearing cones.
Illustration 6 g01192983
9. Install the original shims (23) .
Illustration 7 g01192986
Note: Install the upper cap and lower cap in the original radial location.
10. Install upper cap (21). Install bolts (20) that are equally spaced at 120 degree intervals. The
torque for bolts (20) is 100 ± 20 N·m (75 ± 15 lb ft).
11. Install Tooling (G). Use a suitable torque wrench and Tooling (G) in order to determine the
amount of torque that is needed to rotate the bearing cones. As required, adjust the number
of shims in order to achieve a rolling torque between 1.1 N·m (9.7 lb in) and 5.6 N·m (49.6
lb in).
12. Remove Tooling (G) .
4/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. 13. Remove upper cap (21) and lower cap (22) .
Illustration 8 g03316643
Note: When you install the upper cap and the lower cap on the machine, the sealing lips of
each lip seal must face upward.
14. Position lip seal (25) so that the sealing lip is facing upward. Use Tooling (H) in order to
install lip seal (25) in upper cap (21) so that the seal contacts the counterbore in the upper
cap.
15. Apply Tooling (K) on the sealing lip.
Illustration 9 g03316645
16. Position lip seal (24) so that the sealing lip is facing downward. Use Tooling (H) in order to
install lip seal (24) in lower cap (22) so that the seal contacts the counterbore in the lower
cap.
17. ApplyTooling (K) on the sealing lip.
5/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 10 g01192412
18. Install the proper thickness of shims. Install lower cap (22), upper cap (21), and bolts (20) .
Note: The following steps are used for the assembly of the lower hitch bearings.
Illustration 11 g01193000
19. Position lower cap (31) on the lower frame. Hold the lower cap in place with four bolts (29)
that are equally spaced. Make sure that the lower cap is seated firmly against the upper
frame.
20. Apply Tooling (K) to the bores.
6/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 12 g01193004
21. Lower the temperature of lower bearing cup (39) to −45°C (−49°F).
22. Install lower bearing cup (39). Use Tooling (H) in order to ensure that bearing cup (39)
contacts lower cap (31) .
Illustration 13 g01193008
23. Apply clean oil to bearing cone (40). Install bearing cone (40) in the correct position, as
shown.
7/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 14 g01193014
24. Apply clean oil to bearing cone (41). Install bearing cone (41) in the correct position, as
shown.
Illustration 15 g01193017
25. Lower the temperature of upper bearing cup (41) to −45°C (−49°F).
26. Install upper bearing cup (42). Use Tooling (H) in order to ensure that bearing cup (42)
lightly contacts the bearing cones.
Illustration 16 g01193021
27. Install the original shims (32) .
8/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 17 g01193022
28. Install upper cap (30). Install bolts (29) and the washers that are equally spaced at 90 degree
intervals. The torque for bolts (29) is 100 ± 20 N·m (75 ± 15 lb ft).
29. Install Tooling (J). Use a suitable torque wrench and Tooling (J) in order to determine the
amount of torque that is needed to rotate the bearing cones. As required, adjust the number
of shims in order to achieve a rolling torque between 1.1 N·m (10 lb in) and 5.6 N·m (50 lb
in).
30. Remove Tooling (J) .
31. Remove upper cap (30) and lower cap (31) .
Illustration 18 g01192580
Note: When you install the upper cap and the lower cap on the machine, the sealing lips of
each lip seal must face downward.
32. Position lip seal (33) so that the sealing lip is facing upward. Use Tooling (H) in order to
install lip seal (33) in upper cap (30) so that the seal contacts the counterbore in the upper
cap.
33. ApplyTooling (K) on the sealing lip.
9/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. 34. Position lip seal (34) so that the sealing lip is facing downward. Use Tooling (H) in order to
install lip seal (34) in lower cap (31) so that the seal contacts the counterbore in the lower
cap.
35. ApplyTooling (K) on the sealing lip.
Illustration 19 g01193027
36. Install the proper thickness of shims. Install lower cap (31), upper cap (30), and bolts (29) .
Illustration 20 g01193029
37. Install upper spacer (28) .
10/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SE...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 21 g01193031
38. Apply Tooling (K) to the bores.
39. Lower the temperature of lower sleeve bearing (26) and upper sleeve bearing (27) to −50° ±
5°C (−58° ± 9°F).
40. Install the sleeve bearings. Make sure that the sleeve bearings are flush with the bottom
surface of the bores.
Illustration 22 g01192014
Note: The following steps are used for the connection of the loader frame and the rear
frame.
41. Install Tooling (B) on the loader frame. Attach a suitable lifting device and lifting chains to
Tooling (B) .
42. Use a suitable lifting device in order to raise the loader frame.
11/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SE...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 23 g01193034
Typical Example
43. Remove the suitable cribbing from the loader frame.
Illustration 24 g00364111
44. Use a suitable chain in order to secure the loader frame to the mast of the lift truck, as
shown.
45. Use a suitable lifting device and a suitable lift truck in order to connect the frames.
12/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SE...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 25 g00432878
46. Use Tooling (A) and a suitable lifting device in order to align the bores.
Illustration 26 g01192123
47. ApplyTooling (K) to the upper bores.
Note: Proper alignment of the bores is important.
48. Install pin assembly (19). Install bolt (18) and the washer.
13/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SE...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 27 g01193050
49. ApplyTooling (K) to the lower bores.
50. Install pin (16) .
51. Connect the steering frame lock.
Illustration 28 g01192098
Note: Proper alignment of the bores will ensure that spacer (17) will seat properly.
52. Install lower spacer (17) in the lower hitch. Make sure that the spacer is installed in the
original position.
Illustration 29 g01193052
14/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SE...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. 53. Install lower hitch mount plate (14). Install two bolts (13). The torque for bolts (13) is 68
N·m (50 lb ft).
54. Use a thickness feeler gauge in order to measure the distance between the frame and the
lower hitch mount plate. Check completely around the lower hitch mount plate. Record the
minimum measurement that is found.
Illustration 30 g01192772
55. Remove lower hitch mount plate (14) .
56. Install shims (15) under lower hitch mount plate (14). The shims thickness should equal the
measurement from Step 54 minus 0.25 mm (0.010 inch).
Illustration 31 g01192067
57. Install bolts (12) and (13). The torque for bolts (12) is 100 ± 20 N·m (75 ± 15 lb ft). The
torque for bolts (13) is 570 ± 80 N·m (420 ± 59 lb ft).
15/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SE...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 32 g01192014
58. Remove the suitable lifting device and Tooling (B) from the loader frame.
Illustration 33 g01192031
59. Install bolt (11). Repeat on the other side of the loader frame.
Illustration 34 g03313458
60. Install light assemblies (9) and sensor (10) .
16/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SE...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 35 g01192002
61. Remove the suitable cribbing from the front of the rear frame.
Illustration 36 g00432878
62. Remove Tooling (A) from the rear frame.
17/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SE...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 37 g01193054
63. Install pin assembly (7) and bolt (6) to the rod end of both steering cylinders.
Illustration 38 g01191942
64. Connect hose assembly (3) .
65. Install bolt (4), the washer, and the clip.
66. Connect harness assembly (5) .
Illustration 39 g00847099
67. Connect hose assembly (2) to fixed axle (1) .
68. Fill the oil from the hydraulic tank. Refer to Operation and Maintenance Manual for the
correct procedure.
End By:
a. Install the steering frame lock.
b. Install the center drive shaft.
c. Install the cab.
18/19
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SE...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950H WHEEL LOADER JLX
Configuration: 950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine
Disassembly and Assembly
950H and 962H Wheel Loaders C7 Engine Supplement
Media Number -UENR0788-00 Publication Date -01/10/2012 Date Updated -26/10/2012
i05016190
Steering Frame Lock - Separate and Connect
SMCS - 7506-029
Connection Procedure
Personal injury or death can result from machine articulation or
movement.
Machine frames can move and a person can be crushed.
Connect the steering frame lock link between the front and rear frames
before working on machine. Secure clevis pin with locking pin.
Before operating the machine, fasten the steering frame lock link into
the stored position and secure the clevis pin with locking pin.
Failure to lock into the stored position before operating can result in
loss of steering.
1. Move the machine to a hard, level surface. Park the machine in the straight ahead position
and engage the parking brake.
1/3
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 1 g01172092
2. Remove locking pin (2) from pin (1) .
Illustration 2 g01172098
3. Position steering frame lock (3) to the front frame. Install pin (1) and locking pin (2) .
Note: To align the pin bores, move the front loader frame.
Separation Procedure
Personal injury or death can result from machine articulation or
movement.
Machine frames can move and a person can be crushed.
Connect the steering frame lock link between the front and rear frames
before working on machine. Secure clevis pin with locking pin.
2/3
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Before operating the machine, fasten the steering frame lock link into
the stored position and secure the clevis pin with locking pin.
Failure to lock into the stored position before operating can result in
loss of steering.
Illustration 3 g01172098
1. Remove locking pin (2) and pin (1). Move steering frame lock (3) to the storage position.
Illustration 4 g01172092
2. Install pin (1) and locking pin (2) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Apr 5 14:14:03 UTC+0800 2020
3/3
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950H WHEEL LOADER JLX
Configuration: 950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine
Disassembly and Assembly
950H and 962H Wheel Loaders C7 Engine Supplement
Media Number -UENR0788-00 Publication Date -01/10/2012 Date Updated -26/10/2012
i05016249
System Pressure - Release
SMCS - 4250-553-PX; 4300-553-PX; 5050-553-PX
Release Procedure
Start By:
A. Connect the steering frame lock.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Escaping fluid under pressure, even a pinhole size leak, can penetrate
body tissue, causing serious injury, and possible death. If fluid is
injected into your skin, it must be treated immediately by a doctor
familiar with this type of injury.
1/2
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Always use a board or cardboard when checking for a leak.
1. Move the machine to a location that is smooth, level, and hard. The location should also be
dry and free of debris. Stop the engine.
2. Permit only one operator on the machine. All other personnel should be kept away from the
machine.
3. Lower the bucket and/or work tools to the ground.
4. Engage the parking brake.
5. Stop the engine.
Note: If the machine is equipped with electro-hydraulic controls, turn the engine start
switch key to the ON position before performing the next step. The engine start switch key
must then be turned back to the OFF position before proceeding.
6. Move the control levers several times through the full range of travel. This will relieve any
pressure that may be present in the implement hydraulic system.
7. Depress the brake pedal repeatedly. This will relieve any pressure that may be present in the
braking system.
8. Push in the plunger for the hydraulic tank breaker relief valve until all pressure is released.
Note: If the machine is not equipped with a hydraulic tank breaker relief valve, the
hydraulic tank cap may be removed slowly in order to relieve tank pressure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Apr 5 14:14:53 UTC+0800 2020
2/2
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950H WHEEL LOADER JLX
Configuration: 950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine
Disassembly and Assembly
950H and 962H Wheel Loaders C7 Engine Supplement
Media Number -UENR0788-00 Publication Date -01/10/2012 Date Updated -26/10/2012
i05016272
Hood - Remove
SMCS - 7251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
Illustration 1 g01173155
1. Remove plug (1) from hood (2) .
1/3
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 2 g01173157
2. Open hood (2). Use Tooling (A) and a suitable lifting device in order to support hood (2).
The weight of hood (2) is approximately 181 kg (400 lb).
Illustration 3 g01173331
3. Remove cotter pin (3) and pin (4) from hood tilt actuator (5) in order to disconnect hood tilt
actuator (5) from hood (2) .
Illustration 4 g01173335
2/3
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...