The document provides instructions for removing and disassembling the transmission of a 924K wheel loader. It describes 44 steps to disassemble the transmission including removing hydraulic and electrical connections, brackets, sensors, shafts, bearings, seals and plates. Various tools are required including hydraulic jacks, link brackets, lever pullers, drivers and a compressor. Detailed illustrations accompany each step to show the specific components and order of disassembly.
This document provides instructions for removing and installing a transmission on a 924K wheel loader. It outlines the required tools and gives step-by-step details on disconnecting wiring harnesses, hydraulic lines, and other components to remove the transmission. Detailed illustrations accompany each step. Disassembly of the transmission is then described with steps to remove internal components like valves, shafts, seals, and bearings.
The document provides instructions for removing and disassembling the transmission of a 924K wheel loader. It describes 36 steps to disassemble the transmission including removing hydraulic and electrical connections, brackets, sensors, valves and other components. Special tools are required including hydraulic jacks, link brackets, a lever puller and bearing puller to safely remove and separate the transmission parts. Detailed illustrations accompany each step to show how to disassemble the transmission in the correct order.
The document is a service repair manual that provides instructions for removing and installing the transmission on a 938K wheel loader. It includes:
- A list of required tools for the job.
- Step-by-step instructions for removing the transmission which involve disconnecting wiring harnesses, hoses, and removing mounting bolts.
- Instructions for lowering the transmission safely using a hydraulic jack.
- Instructions for installing the transmission in reverse order.
Caterpillar cat 938 k wheel loader (prefix hfw) service repair manual (hfw000...ifkkdmdmdm
The document provides instructions for removing and disassembling the transmission of a 938K wheel loader. It lists the required tools and gives step-by-step instructions with accompanying illustrations. Key steps include removing the transmission, disassembling the valve assembly and various components, and using pullers to remove bearings from the shaft assembly. Proper safety precautions are needed as some components are heavy.
1) The document provides removal and disassembly instructions for the transmission of a 938K wheel loader.
2) It details over 40 individual steps to remove the transmission, separate its components, and disassemble internal parts like valves, shafts, and seals.
3) Special tools are required for tasks like removing bearings and various transmission components.
1) The document provides removal and disassembly instructions for the transmission of a 938K wheel loader.
2) It details over 40 individual steps to remove the transmission, separate its components, and disassemble internal parts like valves, shafts, and seals.
3) Special tools are required to lift, support, and remove components safely due to the transmission's weight of approximately 145 kg.
This service repair manual provides instructions to disassemble and assemble the transmission of a 924K wheel loader. The removal procedure involves removing components such as the valve assembly, fittings, seals, bearings, and sensors. Tools such as a hydraulic jack, link brackets, and a bearing puller are required. Detailed illustrations accompany each step to correctly position and secure components as the transmission is disassembled.
This service repair manual provides instructions for removing the transmission from a 924K Wheel Loader. It outlines 14 steps to remove the transmission using hydraulic jacks and lifting straps. It then provides detailed disassembly instructions for the transmission, including removing various components like valves, seals, shafts, bearings and sensors. Over 50 detailed illustrations accompany the text to show each step. Proper tools are listed that will be required to complete the disassembly.
This document provides instructions for removing and installing a transmission on a 924K wheel loader. It outlines the required tools and gives step-by-step details on disconnecting wiring harnesses, hydraulic lines, and other components to remove the transmission. Detailed illustrations accompany each step. Disassembly of the transmission is then described with steps to remove internal components like valves, shafts, seals, and bearings.
The document provides instructions for removing and disassembling the transmission of a 924K wheel loader. It describes 36 steps to disassemble the transmission including removing hydraulic and electrical connections, brackets, sensors, valves and other components. Special tools are required including hydraulic jacks, link brackets, a lever puller and bearing puller to safely remove and separate the transmission parts. Detailed illustrations accompany each step to show how to disassemble the transmission in the correct order.
The document is a service repair manual that provides instructions for removing and installing the transmission on a 938K wheel loader. It includes:
- A list of required tools for the job.
- Step-by-step instructions for removing the transmission which involve disconnecting wiring harnesses, hoses, and removing mounting bolts.
- Instructions for lowering the transmission safely using a hydraulic jack.
- Instructions for installing the transmission in reverse order.
Caterpillar cat 938 k wheel loader (prefix hfw) service repair manual (hfw000...ifkkdmdmdm
The document provides instructions for removing and disassembling the transmission of a 938K wheel loader. It lists the required tools and gives step-by-step instructions with accompanying illustrations. Key steps include removing the transmission, disassembling the valve assembly and various components, and using pullers to remove bearings from the shaft assembly. Proper safety precautions are needed as some components are heavy.
1) The document provides removal and disassembly instructions for the transmission of a 938K wheel loader.
2) It details over 40 individual steps to remove the transmission, separate its components, and disassemble internal parts like valves, shafts, and seals.
3) Special tools are required for tasks like removing bearings and various transmission components.
1) The document provides removal and disassembly instructions for the transmission of a 938K wheel loader.
2) It details over 40 individual steps to remove the transmission, separate its components, and disassemble internal parts like valves, shafts, and seals.
3) Special tools are required to lift, support, and remove components safely due to the transmission's weight of approximately 145 kg.
This service repair manual provides instructions to disassemble and assemble the transmission of a 924K wheel loader. The removal procedure involves removing components such as the valve assembly, fittings, seals, bearings, and sensors. Tools such as a hydraulic jack, link brackets, and a bearing puller are required. Detailed illustrations accompany each step to correctly position and secure components as the transmission is disassembled.
This service repair manual provides instructions for removing the transmission from a 924K Wheel Loader. It outlines 14 steps to remove the transmission using hydraulic jacks and lifting straps. It then provides detailed disassembly instructions for the transmission, including removing various components like valves, seals, shafts, bearings and sensors. Over 50 detailed illustrations accompany the text to show each step. Proper tools are listed that will be required to complete the disassembly.
This service repair manual provides instructions for removing the transmission from a 924K Wheel Loader. It outlines 14 steps to remove the transmission using hydraulic jacks and lifting straps. It then provides detailed disassembly instructions for the transmission, including removing various components like valves, shafts, seals, and sensors. Over 50 detailed illustrations accompany the text to show each step. The goal is to repair or replace components of the transmission as needed.
This service repair manual provides instructions for removing the transmission from a 924K Wheel Loader. It outlines 14 steps to remove the transmission using hydraulic jacks and lifting straps. It then provides detailed disassembly instructions for the transmission, including removing valves, gears, seals, sensors and other components. Over 50 detailed illustrations supplement the text instructions. The goal is to provide technicians with a guide to safely and effectively disassemble the transmission for repair or replacement of parts.
The document provides removal and disassembly instructions for the transmission of a 924K Wheel Loader. It details over 30 steps to remove the transmission from the machine and then disassemble the transmission components. Key parts that are disassembled include the valve assembly, housing, shafts, bearings, seals and sensors. Various tools are required including jacks, lifting devices, brackets and a bearing puller. Detailed illustrations accompany each step.
This service repair manual provides instructions for removing the transmission from a 924K Wheel Loader. It outlines 14 steps to remove the transmission using hydraulic jacks and lifting straps. It then provides detailed disassembly instructions for the transmission, including removing various components like valves, seals, shafts, bearings and sensors. Over 50 detailed illustrations accompany the text to show each step. Proper tools are listed that will be required to complete the disassembly.
The document provides removal and disassembly instructions for the transmission of a 924K Wheel Loader. It details over 30 steps to remove the transmission from the machine and then disassemble the transmission components. Key parts that are disassembled include the valve assembly, housing, shafts, bearings, seals and sensors. Various tools are required including jacks, lifting devices, brackets and a bearing puller. Detailed illustrations accompany each step.
This service repair manual provides instructions for removing the transmission from a 924K Wheel Loader. It outlines 14 steps to remove the transmission using hydraulic jacks and lifting straps. It then provides detailed disassembly instructions for the transmission, including removing various components like valves, shafts, seals, and sensors. Over 50 detailed illustrations accompany the text to show each step. The goal is to repair or replace components of the transmission as needed.
The document provides instructions for removing and disassembling the transmission of a 938K wheel loader. It lists 36 steps to disassemble the transmission including removing valves, fittings, seals, sensors, shafts and bearings. Various tools are required including levers, jacks, brackets and a bearing puller. The transmission weighs approximately 145 kg and precautions are described for safely lifting and supporting it during disassembly.
This service repair manual provides instructions for removing and disassembling the transmission of a 938K wheel loader. It lists the required tools and presents step-by-step procedures with illustrations. The transmission and its internal components like valves, shafts, bearings, and seals are removed using various tools including levers, jacks, and bearing pullers. Detailed instructions are provided to disassemble the transmission housing and related parts.
This service repair manual provides instructions for removing and disassembling the transmission of a 938K wheel loader. It lists the required tools and presents step-by-step procedures with illustrations. The transmission and its internal components like valves, shafts, bearings, and seals are removed using various tools including levers, jacks, and bearing pullers. Detailed instructions are provided to disassemble the transmission housing and its internal parts.
This service repair manual provides instructions for removing and disassembling the transmission of a 938K wheel loader. It lists the required tools and presents step-by-step procedures with illustrations. The transmission and its internal components like valves, shafts, bearings, and seals are removed using various tools including levers, jacks, and bearing pullers. Detailed instructions are provided to disassemble the transmission housing and its internal parts.
The document provides instructions for removing and disassembling the transmission of a 938K wheel loader. It lists 36 steps to disassemble the transmission including removing valves, fittings, seals, sensors, shafts and bearings. Various tools are required including levers, jacks, brackets and a bearing puller. The transmission weighs approximately 145 kg and precautions are outlined to safely support and lower it during removal.
1. The document provides removal and disassembly instructions for the transmission of a 930K Wheel Loader. It details over 40 separate steps to remove the transmission, disassemble the internal components, and remove seals and bearings.
2. The removal process involves disconnecting wiring harnesses, hoses, and brackets before lowering the transmission from the machine. Disassembly entails removing the valve assembly, fittings, shafts, bearings, seals, and other internal parts.
3. Detailed illustrations accompany each step to show the specific components and orientation. Special tools are listed that may be required to remove certain components like bearings. Safety notes remind technicians of component weights to avoid injury.
This document provides removal and disassembly instructions for the transmission of a 930K wheel loader. It involves removing the transmission from the machine, then disassembling various components including the valve assembly, housing, shafts, bearings, seals and sensors. Over 30 detailed steps are outlined, making use of various tools to safely remove and disassemble the transmission.
1. The document provides removal and disassembly instructions for the transmission of a 930K Wheel Loader. It details over 40 separate steps to remove the transmission, disassemble the internal components, and remove seals and bearings.
2. The removal process involves disconnecting wiring harnesses, hoses, and brackets before lowering the transmission from the machine. Disassembly entails removing the valve assembly, fittings, shafts, bearings, seals, and other internal parts.
3. Detailed illustrations accompany each step to show the specific components and orientation. Special tools are listed that may be required to remove certain components like bearings. Safety notes remind to use lifting devices when handling heavy parts removed from the machine.
This document provides instructions for removing and installing the transmission on a 930K Wheel Loader. It outlines 14 steps to remove the transmission, which include using hydraulic jacks, removing bolts and disconnecting wiring harnesses. It then lists installing the transmission in reverse order. Further sections detail disassembling the transmission, listing 41 steps to remove internal components like valves, shafts, bearings and seals. Special tools are required and components must be properly supported during removal and installation.
This document provides instructions for removing and installing the transmission on a 930K Wheel Loader. It outlines 14 steps to remove the transmission, which include using hydraulic jacks, removing bolts and disconnecting wiring harnesses. It then lists installing the transmission in reverse order. Further sections detail disassembling the transmission, listing 41 steps such as removing valves, seals, shafts and bearings. Tools including levers, jacks and drivers are required.
This document provides removal and disassembly instructions for the transmission of a 930K wheel loader. It involves removing the transmission from the machine, then disassembling various components including the valve assembly, housing, shafts, bearings, seals and sensors. Over 30 detailed steps are outlined, making use of various tools to safely remove and disassemble the transmission.
1. The document provides removal and disassembly instructions for the transmission of a 930K Wheel Loader. It details over 40 separate steps to remove the transmission, disassemble the internal components, and remove seals and bearings.
2. The removal process involves disconnecting wiring harnesses, hoses, and brackets before lowering the transmission from the machine. Disassembly entails removing the valve assembly, fittings, shafts, bearings, seals, and other internal parts.
3. Tools required include hydraulic jacks, link brackets, lever pullers, drivers, and bearing pullers. Reinstallation is the reverse of the removal process.
This document provides removal and disassembly instructions for the transmission of a 930K wheel loader. It involves removing the transmission from the machine, then disassembling various components including the valve assembly, housing, shafts, bearings, seals and sensors. Over 30 detailed steps are outlined, making use of various tools to safely remove and disassemble the transmission.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hoses and wiring, draining fluid from the elbow, attaching a lifting device to the pump, and removing nuts and the pump. It also includes notes about marking disconnected parts for installation and preventing fluid loss.
The document provides instructions for disassembling and assembling a torque converter. It describes 18 steps to disassemble the torque converter by removing various parts like housing assemblies, bearings, plates, and seals. It then describes 18 steps for assembling the torque converter by installing the parts in reverse order. Tools required include link brackets, drivers, and forcing screws. Safety precautions are provided for spring loaded parts.
The document provides instructions for removing and assembling the torque converter of a 730 Ejector Articulated Truck. It describes in 18 steps how to disassemble the torque converter by removing components like the housing assembly, piston, plates and discs, impeller, and turbine. It then describes in 12 steps the process of assembling the torque converter by reinstalling these components in reverse order, taking care to keep parts clean and install springs and other parts correctly. Special tools are required for tasks like removing the plate and installing the cam.
More Related Content
Similar to Caterpillar Cat 924K Wheel Loader (Prefix HJF) Service Repair Manual Instant Download.pdf
This service repair manual provides instructions for removing the transmission from a 924K Wheel Loader. It outlines 14 steps to remove the transmission using hydraulic jacks and lifting straps. It then provides detailed disassembly instructions for the transmission, including removing various components like valves, shafts, seals, and sensors. Over 50 detailed illustrations accompany the text to show each step. The goal is to repair or replace components of the transmission as needed.
This service repair manual provides instructions for removing the transmission from a 924K Wheel Loader. It outlines 14 steps to remove the transmission using hydraulic jacks and lifting straps. It then provides detailed disassembly instructions for the transmission, including removing valves, gears, seals, sensors and other components. Over 50 detailed illustrations supplement the text instructions. The goal is to provide technicians with a guide to safely and effectively disassemble the transmission for repair or replacement of parts.
The document provides removal and disassembly instructions for the transmission of a 924K Wheel Loader. It details over 30 steps to remove the transmission from the machine and then disassemble the transmission components. Key parts that are disassembled include the valve assembly, housing, shafts, bearings, seals and sensors. Various tools are required including jacks, lifting devices, brackets and a bearing puller. Detailed illustrations accompany each step.
This service repair manual provides instructions for removing the transmission from a 924K Wheel Loader. It outlines 14 steps to remove the transmission using hydraulic jacks and lifting straps. It then provides detailed disassembly instructions for the transmission, including removing various components like valves, seals, shafts, bearings and sensors. Over 50 detailed illustrations accompany the text to show each step. Proper tools are listed that will be required to complete the disassembly.
The document provides removal and disassembly instructions for the transmission of a 924K Wheel Loader. It details over 30 steps to remove the transmission from the machine and then disassemble the transmission components. Key parts that are disassembled include the valve assembly, housing, shafts, bearings, seals and sensors. Various tools are required including jacks, lifting devices, brackets and a bearing puller. Detailed illustrations accompany each step.
This service repair manual provides instructions for removing the transmission from a 924K Wheel Loader. It outlines 14 steps to remove the transmission using hydraulic jacks and lifting straps. It then provides detailed disassembly instructions for the transmission, including removing various components like valves, shafts, seals, and sensors. Over 50 detailed illustrations accompany the text to show each step. The goal is to repair or replace components of the transmission as needed.
The document provides instructions for removing and disassembling the transmission of a 938K wheel loader. It lists 36 steps to disassemble the transmission including removing valves, fittings, seals, sensors, shafts and bearings. Various tools are required including levers, jacks, brackets and a bearing puller. The transmission weighs approximately 145 kg and precautions are described for safely lifting and supporting it during disassembly.
This service repair manual provides instructions for removing and disassembling the transmission of a 938K wheel loader. It lists the required tools and presents step-by-step procedures with illustrations. The transmission and its internal components like valves, shafts, bearings, and seals are removed using various tools including levers, jacks, and bearing pullers. Detailed instructions are provided to disassemble the transmission housing and related parts.
This service repair manual provides instructions for removing and disassembling the transmission of a 938K wheel loader. It lists the required tools and presents step-by-step procedures with illustrations. The transmission and its internal components like valves, shafts, bearings, and seals are removed using various tools including levers, jacks, and bearing pullers. Detailed instructions are provided to disassemble the transmission housing and its internal parts.
This service repair manual provides instructions for removing and disassembling the transmission of a 938K wheel loader. It lists the required tools and presents step-by-step procedures with illustrations. The transmission and its internal components like valves, shafts, bearings, and seals are removed using various tools including levers, jacks, and bearing pullers. Detailed instructions are provided to disassemble the transmission housing and its internal parts.
The document provides instructions for removing and disassembling the transmission of a 938K wheel loader. It lists 36 steps to disassemble the transmission including removing valves, fittings, seals, sensors, shafts and bearings. Various tools are required including levers, jacks, brackets and a bearing puller. The transmission weighs approximately 145 kg and precautions are outlined to safely support and lower it during removal.
1. The document provides removal and disassembly instructions for the transmission of a 930K Wheel Loader. It details over 40 separate steps to remove the transmission, disassemble the internal components, and remove seals and bearings.
2. The removal process involves disconnecting wiring harnesses, hoses, and brackets before lowering the transmission from the machine. Disassembly entails removing the valve assembly, fittings, shafts, bearings, seals, and other internal parts.
3. Detailed illustrations accompany each step to show the specific components and orientation. Special tools are listed that may be required to remove certain components like bearings. Safety notes remind technicians of component weights to avoid injury.
This document provides removal and disassembly instructions for the transmission of a 930K wheel loader. It involves removing the transmission from the machine, then disassembling various components including the valve assembly, housing, shafts, bearings, seals and sensors. Over 30 detailed steps are outlined, making use of various tools to safely remove and disassemble the transmission.
1. The document provides removal and disassembly instructions for the transmission of a 930K Wheel Loader. It details over 40 separate steps to remove the transmission, disassemble the internal components, and remove seals and bearings.
2. The removal process involves disconnecting wiring harnesses, hoses, and brackets before lowering the transmission from the machine. Disassembly entails removing the valve assembly, fittings, shafts, bearings, seals, and other internal parts.
3. Detailed illustrations accompany each step to show the specific components and orientation. Special tools are listed that may be required to remove certain components like bearings. Safety notes remind to use lifting devices when handling heavy parts removed from the machine.
This document provides instructions for removing and installing the transmission on a 930K Wheel Loader. It outlines 14 steps to remove the transmission, which include using hydraulic jacks, removing bolts and disconnecting wiring harnesses. It then lists installing the transmission in reverse order. Further sections detail disassembling the transmission, listing 41 steps to remove internal components like valves, shafts, bearings and seals. Special tools are required and components must be properly supported during removal and installation.
This document provides instructions for removing and installing the transmission on a 930K Wheel Loader. It outlines 14 steps to remove the transmission, which include using hydraulic jacks, removing bolts and disconnecting wiring harnesses. It then lists installing the transmission in reverse order. Further sections detail disassembling the transmission, listing 41 steps such as removing valves, seals, shafts and bearings. Tools including levers, jacks and drivers are required.
This document provides removal and disassembly instructions for the transmission of a 930K wheel loader. It involves removing the transmission from the machine, then disassembling various components including the valve assembly, housing, shafts, bearings, seals and sensors. Over 30 detailed steps are outlined, making use of various tools to safely remove and disassemble the transmission.
1. The document provides removal and disassembly instructions for the transmission of a 930K Wheel Loader. It details over 40 separate steps to remove the transmission, disassemble the internal components, and remove seals and bearings.
2. The removal process involves disconnecting wiring harnesses, hoses, and brackets before lowering the transmission from the machine. Disassembly entails removing the valve assembly, fittings, shafts, bearings, seals, and other internal parts.
3. Tools required include hydraulic jacks, link brackets, lever pullers, drivers, and bearing pullers. Reinstallation is the reverse of the removal process.
This document provides removal and disassembly instructions for the transmission of a 930K wheel loader. It involves removing the transmission from the machine, then disassembling various components including the valve assembly, housing, shafts, bearings, seals and sensors. Over 30 detailed steps are outlined, making use of various tools to safely remove and disassemble the transmission.
Similar to Caterpillar Cat 924K Wheel Loader (Prefix HJF) Service Repair Manual Instant Download.pdf (19)
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hoses and wiring, draining fluid from the elbow, attaching a lifting device to the pump, and removing nuts and the pump. It also includes notes about marking disconnected parts for installation and preventing fluid loss.
The document provides instructions for disassembling and assembling a torque converter. It describes 18 steps to disassemble the torque converter by removing various parts like housing assemblies, bearings, plates, and seals. It then describes 18 steps for assembling the torque converter by installing the parts in reverse order. Tools required include link brackets, drivers, and forcing screws. Safety precautions are provided for spring loaded parts.
The document provides instructions for removing and assembling the torque converter of a 730 Ejector Articulated Truck. It describes in 18 steps how to disassemble the torque converter by removing components like the housing assembly, piston, plates and discs, impeller, and turbine. It then describes in 12 steps the process of assembling the torque converter by reinstalling these components in reverse order, taking care to keep parts clean and install springs and other parts correctly. Special tools are required for tasks like removing the plate and installing the cam.
This document provides assembly instructions for a torque converter in a 730 articulated truck. It lists 34 steps to assemble the various components of the torque converter, including housings, bearings, seals, discs, and shafts. Personal protective equipment is required and cleanliness is emphasized throughout the process. Torque specifications are provided for securing each component with bolts or screws.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing bolts and clips, and installing requires applying sealant
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a Caterpillar C11 engine. The removal process involves using various tools to remove components like the rear crankshaft seal, adapter assembly, gears, bearings and covers. The installation process provides steps to install these components in reverse order and notes that components like bearings must be cooled and properly positioned during installation. Precise dimensions and torque specifications are given for correct installation.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C13 engine.
The removal procedure includes supporting the engine, removing bolts and seals to access the rear gear group components, and using various tools to remove gears, bushings, bearings, and covers. The installation procedure provides instructions for cleaning parts, lowering temperatures of bearings, applying sealant to bolts, and orienting gears and bearings according to specified dimensions before reinstalling the components in reverse order of removal. Separate sections also provide procedures for removing and installing the flywheel and rear crankshaft seal.
This document provides instructions for removing and installing various engine components on a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and rocker arm shaft assembly. The procedures describe disconnecting wiring harnesses, removing nuts and bolts, checking and replacing seals, lubricating parts, and tightening components to the specified torques. Tools required include a feeler gauge and lubricant. Identification marks should be made on removed parts and the components must be kept clean to prevent premature wear.
The document provides instructions for removing and disassembling the drive shaft and scavenge pump on a 657G Wheel Scraper. Key steps include:
1. Removing retaining rings, covers, and guards to access the drive shaft.
2. Using eyebolts and lifting devices to remove the heavy drive shaft and tube assembly.
3. Checking alignment of components and removing the yoke assembly, bearings, and seals from the bearing cage.
4. Disassembling the flywheel scavenge pump by removing bolts, seals, bearings, and shafts.
This document provides instructions for installing and removing various engine components on a Caterpillar 657E wheel scraper model powered by a 3408 engine, including:
1) Installing the rear gear group by placing gears and bearings on shafts and installing dowels, seals and bolts.
2) Removing the flywheel using guide bolts, brackets and a hoist to lift the heavy flywheel off the crankshaft.
3) Installing the flywheel by heating the ring gear, placing the flywheel on guide bolts, and bolting it into place.
4) Procedures for removing and installing the crankshaft rear seal using pullers and punches
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 657E wheel tractor, including:
- Removing the rear gear group by pressing components out of adapter assemblies, using pullers to remove bearings, and disassembling individual gears.
- Installing the rear gear group by pressing bearings into place, assembling individual gears, and pressing assembled components into adapter assemblies.
- Removing the flywheel by using bolts, guide bolts, and a lifting bracket to pull the flywheel off the crankshaft.
- Installing the flywheel by using guide bolts to position it, applying lubricant to bolts, and tightening bol
This document provides instructions for disassembling and assembling the transmission transfer gears of a Caterpillar 651E wheel tractor. The steps include removing the transmission transfer gears as a unit, disassembling the individual gears and bearings, inspecting and replacing parts, and reassembling the gears and bearings in the correct order with the specified tools and torques. Proper installation of seals, shims, and torque specifications are emphasized to ensure correct assembly.
This document provides instructions for removing and installing the rear crankshaft seal on a Caterpillar 651E wheel scraper. The removal procedure involves using a slide hammer puller to pull the rear crankshaft seal from the flywheel housing. The installation procedure specifies cleaning and lubricating the crankshaft and seal bore before pressing the new seal into place. Proper cleaning and lubrication are emphasized to prevent contaminating and shortening the life of components.
The document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It lists the required tools and presents 24 steps to disassemble the various components of the torque converter. These include removing the housing assembly, torque converter assembly, clutch piston, friction disk, bearings, seals and gears. The assembly section then lists the same 24 steps in reverse order to reassemble all components back into the torque converter.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying sealant or heat treating some parts as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift components.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals. Tools are listed that are required for the disassembly procedures.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Tractor. It describes removing over 30 individual components in multiple steps, including removing the torque converter housing, retarder, gears, bearings, seals and other internal parts. Detailed illustrations accompany each step. Cleanliness is emphasized to prevent contaminating the hydraulic system.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Scraper. It lists 32 steps for disassembly that include removing retaining rings, seals, gears, shafts, bearings, and housing assemblies. It then lists 31 steps for assembly in reverse order, providing details on cleaning parts, heating and cooling bearings, and proper torque specifications for fasteners. Tools required are also listed.
This document provides instructions for disassembling and assembling the transfer gears of a 627G wheel tractor. The disassembly process involves removing 18 components from the transfer gear case including bearing cages, gears, shims, and cups. The assembly process describes installing these components in the reverse order and includes lubricating seals, heating/cooling bearings, and torquing bolts to the specified values.
This document provides instructions for disassembling and assembling the torque converter of a 627G Wheel Scraper. It outlines 32 steps to disassemble the various components of the torque converter including the housing, gears, shafts, bearings, and other parts. It then outlines 29 steps for assembling the torque converter components back together in reverse order. Required tools are listed for specific disassembly and assembly steps. Safety notices are provided to contain fluids and properly dispose of them.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 924K WHEEL LOADER HJF
Configuration: 924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
924K, 930K and 938K Wheel Loaders Power Train
Media Number -UENR0281-03 Publication Date -01/04/2017 Date Updated -24/04/2017
i05142776
Transmission
SMCS - 3030
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7505 Hydraulic Jack 1
B
138-7575 Link Bracket 3
1U-9200 Lever Puller Hoist Gp 1
Start By:
A. Remove the front hydrostatic piston motor and the rear hydrostatic piston motor.
1/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g02802456
1. Remove bolts (1) and the caps in order to disconnect drive shaft (2) from the yoke. Discard
bolts (1) .
Illustration 2 g02802476
2. Remove cover (3) .
Illustration 3 g02802517
3. Disconnect harness assemblies (4) and (5) . Reposition harness assemblies (4) and (5) out of
the way.
2/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 4 g02802564
4. Disconnect harness assembly (6) and reposition harness assembly (6) out of the way.
Illustration 5 g02802576
5. Remove bracket (7) .
Illustration 6 g02802636
3/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 6. Disconnect harness assembly (8) . Disconnect tube assembly (9) . Reposition filter base (10)
out of the way.
Illustration 7 g02802997
7. Disconnect harness assembly (11) .
Illustration 8 g02803036
8. Disconnect hose assembly (12) .
4/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 9 g02803097
9. Remove clamp (13) and bolts (15) . Reposition tube assembly (14) and hose assembly (16)
out of the way.
Illustration 10 g02803276
10. Position Tooling (A) under transmission (17) . The weight of transmission (17) is
approximately 145 kg (320 lb). Use suitable straps in order to secure transmission (17) to
Tooling (A) .
5/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 14 g02803577
14. Use Tooling (A) in order to lower transmission (17) .
Illustration 15 g02803580
7/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 16 g02803606
Illustration 17 g02803617
15. Position a suitable bar across transmission mounts (21) . Attach Tooling (B) to the suitable
bar and transmission (17) . The weight of transmission (17) is approximately 145 kg (320
lb).
16. Disconnect the straps that secure transmission (17) to Tooling (A) . Use Tooling (B) in
order to raise transmission (17) off Tooling (A) . Remove Tooling (A) .
17. Use Tooling (A) in order to lower transmission (17) to the ground.
Installation Procedure
1. Install transmission (17) in the reverse order of removal.
8/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 18 g02802456
a. Install new bolts (1) and tighten until snug. Tighten bolts (1) to a torque of 71 ± 10
N·m (52 ± 7 lb ft) using an X pattern.
Disassembly Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
1U-9200 Lever Puller Hoist Gp 1
138-7575 Link Bracket 3
B 308-3470 Jack Stand 3
C 138-7576 Link Bracket 2
D
6V-3009 Crossbar 1
6V-4832 Forcing Screw 1
8H-0663 Bearing Puller Gp 1
126-7181 Sliding Plate 4
126-7177 Puller Leg 2
1P-0510 Driver Gp 1
E 1P-0520 Driver Gp 1
F 4C-3652 Compressor Assembly 1
Start By:
A. Remove the transmission.
9/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 19 g02798341
1. Mark the clip locations and connections. Remove harness assembly (1) .
Illustration 20 g02798420
2. Remove valve assembly (2) .
Illustration 21 g02798422
3. Remove gasket (3) from valve assembly (2) . Remove O-ring seals (4) .
10/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 24 g02798437
6. Remove O-ring seals (8) from valve (7) .
Illustration 25 g02798442
7. Remove temperature sensor (9) from valve assembly (2) .
Illustration 26 g02798445
8. Remove O-ring seal (10) from temperature sensor (9) .
12/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 27 g02798448
9. Remove relief valve (11) from valve assembly (2) .
Illustration 28 g02798449
10. Remove backup rings (12) and O-ring seal (14) from relief valve (11) . Remove backup
rings (13) and O-ring seal (15) . Remove O-ring seal (16) .
Illustration 29 g02798452
13/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. 11. Remove fitting (17) and the O-ring seal from valve assembly (2) . Remove the caps, fittings
(18) , and the O-ring seals. Remove the cap, fitting (19) , and the O-ring seal.
Illustration 30 g02798457
12. Remove bolt (20) and yoke (21) .
Illustration 31 g02798458
13. Remove spacer (22) .
14/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 32 g02798461
14. Remove O-ring seal (23) from yoke (21) .
Illustration 33 g02798465
15. Attach Tooling (A) and a suitable lifting device to transmission (24) . The weight of
transmission (24) is approximately 122 kg (270 lb). Use Tooling (A) and the suitable lifting
device in order to position transmission (24) onto Tooling (B) as shown on Illustration 33.
Illustration 34 g02798473
15/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. 16. Remove bolt (25) and remove yoke (26) . Remove bolts (27) .
Illustration 35 g02798479
17. Remove O-ring seal (28) from yoke (26) .
Illustration 36 g02798481
18. Attach Tooling (C) and a suitable lifting device to housing (29) . The weight of housing (29)
is approximately 45 kg (100 lb). Use Tooling (C) and the suitable lifting device in order to
remove housing (29) .
16/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 50 g02798511
32. Remove bolt (45) . Remove sensor (44) and the O-ring seal.
33. Remove bolt (46) . Remove sensor (47) and the O-ring seal.
34. Remove plug (48) and the O-ring seal.
Illustration 51 g02798512
35. Remove shaft assembly (49) .
Illustration 52 g02798514
36. Use Tooling (D) in order to remove bearing cone (50) from shaft assembly (49) .
22/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 53 g02798517
37. Use Tooling (D) in order to remove bearing cone (51) from shaft assembly (49) .
Illustration 54 g02798519
38. Remove bearing cup (52) .
Illustration 55 g02798520
39. Remove shaft assembly (53) .
23/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 56 g02798521
40. Use Tooling (D) in order to remove bearing cone (54) from shaft assembly (53) .
Illustration 57 g02798522
41. Use Tooling (D) in order to remove bearing cone (55) from shaft assembly (53) .
24/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 58 g02798523
42. Remove bearing cup (56) .
Illustration 59 g02798524
43. Remove bolts (57) and remove plate (58) .
Illustration 60 g02798526
44. Remove bolts (59) from plate (58) . Remove seal assembly (60) .
25/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 61 g02798527
45. Use Tooling (E) and a suitable press in order to remove seal (61) (not shown) from seal
assembly (60) .
Illustration 62 g02798529
46. Remove shaft assembly (62) .
Illustration 63 g02798530
26/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. 47. Use Tooling (D) in order to remove gear assembly (63) from shaft assembly (62) .
Illustration 64 g02798531
48. Remove bearing cone (64) from gear assembly (63) .
Illustration 65 g02798532
49. Remove thrust washer (65) .
27/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
30. Illustration 69 g02798701
53. Remove thrust bearing (70) .
Illustration 70 g02798703
54. Remove thrust washer (71) and retaining ring (72) .
Illustration 71 g02798709
55. Remove end plate (73) .
29/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
31. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
32. Illustration 72 g02798714
Illustration 73 g02798715
Illustration 74 g02798976
56. Remove friction discs (74) and plates (75) ending with end plate (76) .
30/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
33. Illustration 75 g02798719
Illustration 76 g02798724
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
57. Use Tooling (F) and a suitable press in order to compress spring (77) (not shown) in shaft
assembly (62) .
31/76
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engin...
2021/1/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...