This document provides instructions for disassembling and assembling the final drive of a 5090B excavator. It lists the required tools and outlines 32 steps for disassembly, including removing gears, shafts, seals and housings. The assembly section lists tools and outlines 29 steps, including pressing in bearings, installing seals, determining shim thickness, and reassembling gears, shafts and housings. The goal is to thoroughly clean parts and reinstall them in their original locations, applying anti-seize compound as needed.
This document provides instructions for disassembling and assembling a final drive on 385B and 385B L excavators. The disassembly process involves removing 27 components from the final drive housing using various tools. The assembly process reverses the disassembly steps and provides details on installing bearings and seals using anti-seize compound and determining the correct shim thickness between components.
Caterpillar cat 385 b excavator (prefix bly) service repair manual (bly00001 ...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of 385B and 385B L Excavators. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts before disassembly.
3) Reassembling the components in reverse order, applying lubricants to bearings and sealing surfaces.
4) Using a hydraulic press and load tester to properly install bearings and determine the correct shim thickness.
Caterpillar cat 385 b l excavator (prefix bly) service repair manual (bly0000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of 385B and 385B L Excavators.
The disassembly procedure involves removing 27 parts from the final drive housing using various tools. This includes removing gears, shafts, washers, bearings and seals.
The assembly procedure instructs to thoroughly clean all parts, apply anti-seize compound, and install parts in reverse order of disassembly. Proper bearing preload is achieved by applying hydraulic pressure and measuring step length on the coupling gear.
Caterpillar cat 385 b l excavator (prefix bly) service repair manual (bly0000...fjjskekdmme
This document provides instructions for disassembling and assembling a final drive on 385B and 385B L excavators. The disassembly process involves removing 27 components from the final drive housing using various tools. The assembly process reverses the disassembly steps and provides details on installing bearings and seals using anti-seize compound and determining the correct shim thickness between components.
Caterpillar cat 385 b excavator (prefix bly) service repair manual (bly00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of 385B and 385B L Excavators.
The disassembly procedure involves removing 27 parts from the final drive housing using various tools. This includes removing gears, shafts, washers, bearings and seals.
The assembly procedure instructs to thoroughly clean all parts, apply anti-seize compound, and install parts in reverse order of disassembly. It provides details on installing bearings and determining the correct number of shims using a hydraulic press and micrometer measurements.
Caterpillar cat 385 b excavator (prefix bly) service repair manual (bly00001 ...fjjskekdmme
This document provides instructions for disassembling and assembling a final drive on 385B and 385B L excavators. The disassembly process involves removing 27 components from the final drive housing using various tools. The assembly process reverses the disassembly steps and provides details on installing bearings and seals using anti-seize compound and determining the correct shim thickness between components.
Caterpillar cat 385 b l excavator (prefix bly) service repair manual (bly0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of 385B and 385B L Excavators.
The disassembly procedure involves removing 27 parts from the final drive housing using various tools. This includes removing gears, shafts, washers, bearings and seals.
The assembly procedure instructs to thoroughly clean all parts, apply anti-seize compound, and install parts in reverse order of disassembly. Special steps are provided to determine the correct bearing preload using shims and applying hydraulic pressure.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to assembly.
3) Assembling the components in reverse order, applying lubricants to bearings and sealing surfaces.
4) Using tools and procedures to properly set bearing preload when installing the main housing.
This document provides instructions for disassembling and assembling a final drive on 385B and 385B L excavators. The disassembly process involves removing 27 components from the final drive housing using various tools. The assembly process reverses the disassembly steps and provides details on installing bearings and seals using anti-seize compound and determining the correct shim thickness between components.
Caterpillar cat 385 b excavator (prefix bly) service repair manual (bly00001 ...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of 385B and 385B L Excavators. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts before disassembly.
3) Reassembling the components in reverse order, applying lubricants to bearings and sealing surfaces.
4) Using a hydraulic press and load tester to properly install bearings and determine the correct shim thickness.
Caterpillar cat 385 b l excavator (prefix bly) service repair manual (bly0000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of 385B and 385B L Excavators.
The disassembly procedure involves removing 27 parts from the final drive housing using various tools. This includes removing gears, shafts, washers, bearings and seals.
The assembly procedure instructs to thoroughly clean all parts, apply anti-seize compound, and install parts in reverse order of disassembly. Proper bearing preload is achieved by applying hydraulic pressure and measuring step length on the coupling gear.
Caterpillar cat 385 b l excavator (prefix bly) service repair manual (bly0000...fjjskekdmme
This document provides instructions for disassembling and assembling a final drive on 385B and 385B L excavators. The disassembly process involves removing 27 components from the final drive housing using various tools. The assembly process reverses the disassembly steps and provides details on installing bearings and seals using anti-seize compound and determining the correct shim thickness between components.
Caterpillar cat 385 b excavator (prefix bly) service repair manual (bly00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of 385B and 385B L Excavators.
The disassembly procedure involves removing 27 parts from the final drive housing using various tools. This includes removing gears, shafts, washers, bearings and seals.
The assembly procedure instructs to thoroughly clean all parts, apply anti-seize compound, and install parts in reverse order of disassembly. It provides details on installing bearings and determining the correct number of shims using a hydraulic press and micrometer measurements.
Caterpillar cat 385 b excavator (prefix bly) service repair manual (bly00001 ...fjjskekdmme
This document provides instructions for disassembling and assembling a final drive on 385B and 385B L excavators. The disassembly process involves removing 27 components from the final drive housing using various tools. The assembly process reverses the disassembly steps and provides details on installing bearings and seals using anti-seize compound and determining the correct shim thickness between components.
Caterpillar cat 385 b l excavator (prefix bly) service repair manual (bly0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of 385B and 385B L Excavators.
The disassembly procedure involves removing 27 parts from the final drive housing using various tools. This includes removing gears, shafts, washers, bearings and seals.
The assembly procedure instructs to thoroughly clean all parts, apply anti-seize compound, and install parts in reverse order of disassembly. Special steps are provided to determine the correct bearing preload using shims and applying hydraulic pressure.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to assembly.
3) Assembling the components in reverse order, applying lubricants to bearings and sealing surfaces.
4) Using tools and procedures to properly set bearing preload when installing the main housing.
Caterpillar Cat CS-573E, CP-573E Vibratory Compactor (Prefix CEB) Service Rep...8fusejkdmd9i
This document provides assembly instructions for installing a final drive planetary on vibratory compactor models CS-573E and CP-573E. It outlines 39 steps to assemble components like retaining rings, bearings, seals, gears, pins and discs. It also provides instructions for installing the assembled final drive planetary and checking brake piston displacement. Tools required include push-pullers, drivers, grease, thread lock compound and dial indicators.
Caterpillar Cat CS-583C Vibratory Compactor (Prefix 7NN) Service Repair Manua...8fusejkdmd9i
This document provides instructions for removing and installing pistons and connecting rods in a CS-583C vibratory compactor powered by a 3116 engine. It outlines the required tools and safety notices. The procedures describe removing main crankshaft bearings, installing piston rings using compressors, inserting pistons and connecting rods into cylinders while tapping with hammers, and torquing connecting rod cap bolts to the specified values. References are provided for determining if parts can be reused.
Caterpillar Cat CS-573C Vibratory Compactor (Prefix 6LN) Service Repair Manua...8fusejkdmd9i
This document provides instructions for removing the engine oil filter base from a Caterpillar CS-573C vibratory compactor powered by a 3116 engine. The procedure involves first draining the engine oil. Then a special tool is used to remove the oil filter base from the engine block. Contaminants should be avoided to prevent wear. Reusable parts specifications are referenced.
Caterpillar Cat CS-573E and CP-573E Vibratory Compactor (Prefix ASZ) Service ...8fusejkdmd9i
This document provides installation instructions for a final drive planetary on vibratory compactor models CS-573E and CP-573E. It outlines 39 steps to install components like retaining rings, bearings, seals, gears, and brackets. Tools required include push-pullers, drivers, grease, thread lock compound, and dial indicators. Installation must be done in the correct sequence and components must be cleaned, inspected, and lubricated during assembly.
The document provides instructions for connecting the final drive, steering clutch, and brakes of a D6N track-type tractor. It instructs the user to install an O-ring seal onto the steering clutch and brakes assembly and position it onto the final drive. Bolts are then installed to connect the assemblies. The lifting device and tooling are removed once the connection is made.
Caterpillar Cat CS-573E, CP-573E Vibratory Compactor (Prefix CNN) Service Rep...8fusejkdmd9i
This document provides step-by-step instructions for disassembling the piston pump on a CS-573E and CP-573E vibratory compactor. It begins by describing how to remove the propel pumps and cleaning the component. It then lists 45 detailed steps to disassemble the various parts of the piston pump, including the head assembly, cylinder assembly, control assembly, cradle assembly, housing components, shaft, covers, and nozzles. Precautions are provided for relieving spring pressure. The document includes illustrations for each step.
Caterpillar Cat CS-563E, CP-563E Vibratory Compactor (Prefix CNG) Service Rep...8fusejkdmd9i
The document provides step-by-step instructions for disassembling the piston pump on a vibratory compactor. It lists 45 steps to remove components like the mounting flange, seals, couplings, valves, springs, pistons, housings and more. Detailed illustrations accompany each step. Cleanliness is important during disassembly to prevent dirt from entering parts. Marking component orientations aids reassembly. Disassembly of the control assembly and cylinder assembly are also described in detail.
This document provides assembly and disassembly instructions for the steering and implement pump on a D6H track-type tractor. It details 44 steps to disassemble the pump into its individual components and 38 steps to reassemble it. Key components that are disassembled include the cylinder barrel, pistons, swashplate, shaft, valves and housings. The document ensures each part is cleaned, inspected and lubricated before precise reassembly to factory specifications.
Caterpillar Cat CS-573D Vibratory Compactor (Prefix 2YZ) Service Repair Manua...8fusejkdmd9i
This document provides instructions for removing and installing inlet and exhaust valve guides on a CS-573D vibratory compactor powered by a 3116 engine. It lists the required tools and gives step-by-step procedures for removing the valve guides from the cylinder head and installing new guides. Safety notices are provided to keep parts clean and contain fluids during the process.
Caterpillar Cat CS-573D Vibratory Compactor (Prefix CMK) Service Repair Manua...8fusejkdmd9i
This document provides instructions for assembling pistons and connecting rods in a CS-573D Vibratory Compactor powered by a 3116 engine. It outlines the required tools and gives step-by-step instructions that include installing piston rings, connecting rod bearings, pistons onto connecting rods, and connecting rods onto the crankshaft. References are provided for determining reusability of parts and additional information.
Caterpillar Cat CS-563D VIBRATORY COMPACTOR (Prefix 1SZ) Service Repair Manua...8fusejkdmd9i
This document provides instructions for removing and installing a cylinder head on a Caterpillar CS-563D vibratory compactor with a 3116 engine. The removal procedure involves removing several other engine components before removing the cylinder head. The installation procedure specifies cleaning and lubricating the cylinder head and block mating surfaces, installing a new gasket, and tightening the cylinder head bolts in a specific sequence to the specified torque.
Caterpillar Cat CS-533E VIBRATORY COMPACTOR (Prefix TJL) Service Repair Manua...8fusejkdmd9i
This document provides installation instructions for assembling and installing a piston pump on a CS-533E vibratory compactor. It outlines 35 steps for assembling piston pump components like seals, bearings, valves and fittings. It then describes 7 steps for installing the assembled pump, including attaching hoses and electrical connections. The overall procedure is to carefully assemble the pump components and then lift and secure the pump inside the compactor, completing all fluid and electrical connections.
Caterpillar Cat CS-533E, CP-533E Vibratory Compactor (Prefix BZE) Service Rep...8fusejkdmd9i
The document provides instructions for disassembling and assembling the piston motor (drum propel) of CS-533E and CP-533E vibratory soil compactors. The disassembly procedure involves removing 33 parts in sequential order, taking care with springs. The assembly procedure involves installing the same 33 parts in reverse order, also taking care with springs. Cleanliness is emphasized throughout to prevent damage to precision components.
Caterpillar Cat CS-533E and CP-533E Vibratory Compactor (Prefix ASL) Service ...8fusejkdmd9i
This document provides instructions for disassembling and assembling the piston pump used for drum propulsion on vibratory compactor models CS-533E and CP-533E. The disassembly procedure involves removing 28 components from the pump in 12 steps using various tools. Cleaning and inspecting parts is emphasized before reassembly in the reverse order over 28 steps.
Caterpillar Cat CS-533E VIBRATORY COMPACTOR (Prefix TBE) Service Repair Manua...8fusejkdmd9i
This document provides instructions for disassembling and assembling the piston pump of a CS-533E vibratory soil compactor. It describes the required tools and gives step-by-step instructions to remove, disassemble, and assemble the pump. The instructions include removing seals, bolts, valves, housings, and other components. Precautions are provided to clean parts thoroughly and check components for wear.
Caterpillar Cat CS-531D Vibratory Compactor (Prefix 3AZ) Service Repair Manua...8fusejkdmd9i
1. The document provides instructions for removing and installing a governor from an engine. It describes using various tools to remove clips, pins, tubes, and seals before removing the governor.
2. To install the governor, the instructions specify applying lubricant to new seals and placing them on components before reinstalling parts in reverse order. Proper adjustment of the fuel setting is also mentioned.
3. Additional instructions are provided to remove the fuel injection control linkage by removing clips and pins connecting it to the governor. References are made to other documents for additional information.
Caterpillar Cat CS-531D Vibratory Compactor (Prefix 4MZ) Service Repair Manua...8fusejkdmd9i
This service repair manual provides instructions for installing a governor on a Caterpillar 3116 engine that powers a CS-531D vibratory compactor. The instructions include applying lubricant to O-rings, placing the governor in position, installing clips and bolts to secure it, and connecting the fuel injection control linkage. Tools required include governor pliers and various pins and pilots. The document provides illustrations and numbered steps for each part of the installation process.
Caterpillar Cat CS-531D Vibratory Compactor (Prefix AGH) Service Repair Manua...8fusejkdmd9i
1. The document provides step-by-step instructions for removing a governor from a Caterpillar 3116 engine, which includes disconnecting linkages, removing clips and bolts, and using special tools.
2. Instructions are also given for installing a new governor, which involves applying lubricant to seals, placing parts in position, and reconnecting linkages.
3. References are made to other documents for additional information on governor inspection and calibration.
Caterpillar Cat CS-531C Vibratory Compactor (Prefix 9RN) Service Repair Manua...8fusejkdmd9i
This document provides instructions for removing and installing inlet and exhaust valve seats in a CS-531C vibratory compactor powered by a 3116 engine. It describes the required tools and steps to remove the valves, valve guides, and valve seat inserts from the cylinder head. It also outlines the installation procedure and specifies cleaning parts to prevent contaminants from causing premature wear. References are provided for guidelines on determining if parts can be reused.
Caterpillar Cat CS-433E, CP-433E Vibratory Compactor (Prefix DAC) Service Rep...8fusejkdmd9i
The document provides instructions for disassembling and assembling the piston motor (drum propel) on vibratory compactor models CS-433E and CP-433E. It describes removing and installing various parts like housing caps, seals, springs, pistons, and covers. The instructions include illustrations showing the assembly and require following proper safety procedures when relieving spring pressure.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Caterpillar Cat CS-573E, CP-573E Vibratory Compactor (Prefix CEB) Service Rep...8fusejkdmd9i
This document provides assembly instructions for installing a final drive planetary on vibratory compactor models CS-573E and CP-573E. It outlines 39 steps to assemble components like retaining rings, bearings, seals, gears, pins and discs. It also provides instructions for installing the assembled final drive planetary and checking brake piston displacement. Tools required include push-pullers, drivers, grease, thread lock compound and dial indicators.
Caterpillar Cat CS-583C Vibratory Compactor (Prefix 7NN) Service Repair Manua...8fusejkdmd9i
This document provides instructions for removing and installing pistons and connecting rods in a CS-583C vibratory compactor powered by a 3116 engine. It outlines the required tools and safety notices. The procedures describe removing main crankshaft bearings, installing piston rings using compressors, inserting pistons and connecting rods into cylinders while tapping with hammers, and torquing connecting rod cap bolts to the specified values. References are provided for determining if parts can be reused.
Caterpillar Cat CS-573C Vibratory Compactor (Prefix 6LN) Service Repair Manua...8fusejkdmd9i
This document provides instructions for removing the engine oil filter base from a Caterpillar CS-573C vibratory compactor powered by a 3116 engine. The procedure involves first draining the engine oil. Then a special tool is used to remove the oil filter base from the engine block. Contaminants should be avoided to prevent wear. Reusable parts specifications are referenced.
Caterpillar Cat CS-573E and CP-573E Vibratory Compactor (Prefix ASZ) Service ...8fusejkdmd9i
This document provides installation instructions for a final drive planetary on vibratory compactor models CS-573E and CP-573E. It outlines 39 steps to install components like retaining rings, bearings, seals, gears, and brackets. Tools required include push-pullers, drivers, grease, thread lock compound, and dial indicators. Installation must be done in the correct sequence and components must be cleaned, inspected, and lubricated during assembly.
The document provides instructions for connecting the final drive, steering clutch, and brakes of a D6N track-type tractor. It instructs the user to install an O-ring seal onto the steering clutch and brakes assembly and position it onto the final drive. Bolts are then installed to connect the assemblies. The lifting device and tooling are removed once the connection is made.
Caterpillar Cat CS-573E, CP-573E Vibratory Compactor (Prefix CNN) Service Rep...8fusejkdmd9i
This document provides step-by-step instructions for disassembling the piston pump on a CS-573E and CP-573E vibratory compactor. It begins by describing how to remove the propel pumps and cleaning the component. It then lists 45 detailed steps to disassemble the various parts of the piston pump, including the head assembly, cylinder assembly, control assembly, cradle assembly, housing components, shaft, covers, and nozzles. Precautions are provided for relieving spring pressure. The document includes illustrations for each step.
Caterpillar Cat CS-563E, CP-563E Vibratory Compactor (Prefix CNG) Service Rep...8fusejkdmd9i
The document provides step-by-step instructions for disassembling the piston pump on a vibratory compactor. It lists 45 steps to remove components like the mounting flange, seals, couplings, valves, springs, pistons, housings and more. Detailed illustrations accompany each step. Cleanliness is important during disassembly to prevent dirt from entering parts. Marking component orientations aids reassembly. Disassembly of the control assembly and cylinder assembly are also described in detail.
This document provides assembly and disassembly instructions for the steering and implement pump on a D6H track-type tractor. It details 44 steps to disassemble the pump into its individual components and 38 steps to reassemble it. Key components that are disassembled include the cylinder barrel, pistons, swashplate, shaft, valves and housings. The document ensures each part is cleaned, inspected and lubricated before precise reassembly to factory specifications.
Caterpillar Cat CS-573D Vibratory Compactor (Prefix 2YZ) Service Repair Manua...8fusejkdmd9i
This document provides instructions for removing and installing inlet and exhaust valve guides on a CS-573D vibratory compactor powered by a 3116 engine. It lists the required tools and gives step-by-step procedures for removing the valve guides from the cylinder head and installing new guides. Safety notices are provided to keep parts clean and contain fluids during the process.
Caterpillar Cat CS-573D Vibratory Compactor (Prefix CMK) Service Repair Manua...8fusejkdmd9i
This document provides instructions for assembling pistons and connecting rods in a CS-573D Vibratory Compactor powered by a 3116 engine. It outlines the required tools and gives step-by-step instructions that include installing piston rings, connecting rod bearings, pistons onto connecting rods, and connecting rods onto the crankshaft. References are provided for determining reusability of parts and additional information.
Caterpillar Cat CS-563D VIBRATORY COMPACTOR (Prefix 1SZ) Service Repair Manua...8fusejkdmd9i
This document provides instructions for removing and installing a cylinder head on a Caterpillar CS-563D vibratory compactor with a 3116 engine. The removal procedure involves removing several other engine components before removing the cylinder head. The installation procedure specifies cleaning and lubricating the cylinder head and block mating surfaces, installing a new gasket, and tightening the cylinder head bolts in a specific sequence to the specified torque.
Caterpillar Cat CS-533E VIBRATORY COMPACTOR (Prefix TJL) Service Repair Manua...8fusejkdmd9i
This document provides installation instructions for assembling and installing a piston pump on a CS-533E vibratory compactor. It outlines 35 steps for assembling piston pump components like seals, bearings, valves and fittings. It then describes 7 steps for installing the assembled pump, including attaching hoses and electrical connections. The overall procedure is to carefully assemble the pump components and then lift and secure the pump inside the compactor, completing all fluid and electrical connections.
Caterpillar Cat CS-533E, CP-533E Vibratory Compactor (Prefix BZE) Service Rep...8fusejkdmd9i
The document provides instructions for disassembling and assembling the piston motor (drum propel) of CS-533E and CP-533E vibratory soil compactors. The disassembly procedure involves removing 33 parts in sequential order, taking care with springs. The assembly procedure involves installing the same 33 parts in reverse order, also taking care with springs. Cleanliness is emphasized throughout to prevent damage to precision components.
Caterpillar Cat CS-533E and CP-533E Vibratory Compactor (Prefix ASL) Service ...8fusejkdmd9i
This document provides instructions for disassembling and assembling the piston pump used for drum propulsion on vibratory compactor models CS-533E and CP-533E. The disassembly procedure involves removing 28 components from the pump in 12 steps using various tools. Cleaning and inspecting parts is emphasized before reassembly in the reverse order over 28 steps.
Caterpillar Cat CS-533E VIBRATORY COMPACTOR (Prefix TBE) Service Repair Manua...8fusejkdmd9i
This document provides instructions for disassembling and assembling the piston pump of a CS-533E vibratory soil compactor. It describes the required tools and gives step-by-step instructions to remove, disassemble, and assemble the pump. The instructions include removing seals, bolts, valves, housings, and other components. Precautions are provided to clean parts thoroughly and check components for wear.
Caterpillar Cat CS-531D Vibratory Compactor (Prefix 3AZ) Service Repair Manua...8fusejkdmd9i
1. The document provides instructions for removing and installing a governor from an engine. It describes using various tools to remove clips, pins, tubes, and seals before removing the governor.
2. To install the governor, the instructions specify applying lubricant to new seals and placing them on components before reinstalling parts in reverse order. Proper adjustment of the fuel setting is also mentioned.
3. Additional instructions are provided to remove the fuel injection control linkage by removing clips and pins connecting it to the governor. References are made to other documents for additional information.
Caterpillar Cat CS-531D Vibratory Compactor (Prefix 4MZ) Service Repair Manua...8fusejkdmd9i
This service repair manual provides instructions for installing a governor on a Caterpillar 3116 engine that powers a CS-531D vibratory compactor. The instructions include applying lubricant to O-rings, placing the governor in position, installing clips and bolts to secure it, and connecting the fuel injection control linkage. Tools required include governor pliers and various pins and pilots. The document provides illustrations and numbered steps for each part of the installation process.
Caterpillar Cat CS-531D Vibratory Compactor (Prefix AGH) Service Repair Manua...8fusejkdmd9i
1. The document provides step-by-step instructions for removing a governor from a Caterpillar 3116 engine, which includes disconnecting linkages, removing clips and bolts, and using special tools.
2. Instructions are also given for installing a new governor, which involves applying lubricant to seals, placing parts in position, and reconnecting linkages.
3. References are made to other documents for additional information on governor inspection and calibration.
Caterpillar Cat CS-531C Vibratory Compactor (Prefix 9RN) Service Repair Manua...8fusejkdmd9i
This document provides instructions for removing and installing inlet and exhaust valve seats in a CS-531C vibratory compactor powered by a 3116 engine. It describes the required tools and steps to remove the valves, valve guides, and valve seat inserts from the cylinder head. It also outlines the installation procedure and specifies cleaning parts to prevent contaminants from causing premature wear. References are provided for guidelines on determining if parts can be reused.
Caterpillar Cat CS-433E, CP-433E Vibratory Compactor (Prefix DAC) Service Rep...8fusejkdmd9i
The document provides instructions for disassembling and assembling the piston motor (drum propel) on vibratory compactor models CS-433E and CP-433E. It describes removing and installing various parts like housing caps, seals, springs, pistons, and covers. The instructions include illustrations showing the assembly and require following proper safety procedures when relieving spring pressure.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: FRONT SHOVEL
Model: 5090B FRONT SHOVEL SJY
Configuration: 5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine
Disassembly and Assembly
385B and 5090B Excavators Excavator Systems
Media Number -RENR5407-06 Publication Date -01/02/2016 Date Updated -12/02/2016
i01674800
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7575 Link Bracket 3
C 138-7576 Link Bracket 2
D
132-8119 Hydraulic Wrench 1
132-8223 Hydraulic Pump and Motor Gp 1
9U-7418 Hex Bit Socket 1
E 176-6536 Forcing Bolt 2
Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
1. Thoroughly clean the outside of the final drive prior to disassembly.
1/11
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00865168
2. Fasten the final drive to Tooling (A). Put an alignment mark across the sections of the final
drive for assembly purposes. All parts must be reinstalled in the original locations. The
weight of the final drive is approximately 1020 kg (2250 lb).
Illustration 2 g00865172
3. Remove socket head bolts (1) from the final drive cover.
Illustration 3 g00865173
4. Fasten Tooling (B) and a suitable lifting device to cover (2).
2/11
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 5. Remove bolts (3). Use a soft faced hammer to break the seal between the cover and the ring
gear. Remove cover (2). The weight of the cover is approximately 95 kg (210 lb).
Illustration 4 g00865183
6. Remove spacer (4) and the shims from the cover.
7. Remove socket head bolts (5) and ring gear (6) from the cover.
Illustration 5 g00865487
8. Remove sun gear (7).
Illustration 6 g00865501
3/11
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 9. Use a hoist and Tooling (B) to remove carrier assembly (8). The weight of the carrier
assembly is approximately 43 kg (95 lb).
Illustration 7 g00865534
10. Remove retaining ring (9), spacer (10), and sun gear (11).
Illustration 8 g00865551
11. Drive spring pin (13) into shaft (14). Remove shaft (14) and gear assembly (12).
Illustration 9 g00865614
4/11
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 12. Remove washers (15) and bearing (16) from gear (17). Remove spring pin (13) from shaft
(14).
13. Repeat Steps 11 and 12 for the remaining gear assemblies.
Illustration 10 g00865671
14. Use a hoist and Tooling (B) to remove carrier assembly (18). The weight of the carrier
assembly is approximately 95 kg (210 lb).
Illustration 11 g00865717
15. Remove retaining ring (19), spacer (20), and gear assembly (21).
5/11
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 12 g00865736
16. Drive spring pin (22) into planetary shaft (24). Remove planetary shaft (24) and gear
assembly (23).
Illustration 13 g00865753
17. Remove thrust washers (27) and bearing (26) from planetary gear (25). Remove spring pin
(22) from shaft (24).
18. Repeat Steps 16 and 17 for the remaining gear assemblies.
Illustration 14 g00865862
19. Use a hoist and Tooling (B) to remove carrier assembly (28). The weight of the carrier
assembly is approximately 132 kg (290 lb). Remove spacer (29).
6/11
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g00865872
20. Drive spring pin (31) into shaft (32). Remove planetary shaft (32) and gear assembly (30).
Illustration 16 g00865884
21. Remove thrust washers (33) and (37), and bearings (34) and (36) from planetary gear (35).
Remove spring pin (31) from shaft (32).
22. Repeat Steps 20 and 21 for the remaining gear assemblies.
Illustration 17 g00865931
7/11
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 23. Use a hoist and Tooling (B) to remove ring gear (38) from housing (39). The weight of the
ring gear is approximately 155 kg (340 lb).
Illustration 18 g00865939
24. Remove O-ring seal (40) from the main housing.
Illustration 19 g00865955
25. Place wood blocks under the final drive in order to support the motor housing.
Illustration 20 g00866047
8/11
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 21 g00865969
26. Use Tooling (D) to remove bolts (41) from gear (42).
Note: A part of Tooling (D) must be modified. Cut Length (X) on a 9U-7418 Hex Bit
Socket to a length of 14 mm (0.55 inch).
Illustration 22 g00866066
27. Install Tooling (E) in the gear, as shown. Tighten Tooling (E) evenly in order to loosen the
gear. Remove the gear from the motor housing.
Illustration 23 g00866072
9/11
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 28. Remove shims (43) from the motor housing.
Illustration 24 g00866085
29. Remove bolts (44). Use Tooling (C) and a hoist to separate main housing (45) from motor
housing (39). The motor housing will rest on the wood blocks. The weight of the main
housing is approximately 250 kg (550 lb).
Illustration 25 g00866095
30. Remove bearing (46) from the main housing.
Illustration 26 g00866100
10/11
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP3...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 31. Remove Duo-Cone seal (47), and bearing cups (48) and (49) from the main housing.
Illustration 27 g00866156
32. Remove pins (50), if necessary.
33. Remove bearing (51).
34. Remove Duo-Cone seal (52) from the motor housing.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 23 18:04:14 UTC+0800 2021
11/11
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP3...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: FRONT SHOVEL
Model: 5090B FRONT SHOVEL SJY
Configuration: 5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine
Disassembly and Assembly
385B and 5090B Excavators Excavator Systems
Media Number -RENR5407-06 Publication Date -01/02/2016 Date Updated -12/02/2016
i01678933
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7576 Link Bracket 3
C 205-8241 Installer 1
D
132-8119 Hydraulic Wrench 1
132-8223 Hydraulic Pump and Motor Gp 1
9U-7418 Hex Bit Socket 1
E 138-7575 Link Bracket 3
F 6V-3175 Double Acting Cylinder 1
3S-6224 Electric Hydraulic Pump Gp 1
1U-9889 Crossblock 1
9S-7338 Crossblock 1
150-1961 Washer 2
150-1786 Plate 2
4C-9634 Puller Stud 1
9U-6832 Nut 1
1/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 2K-7468 Locknut 1
4K-0684 Locknut 2
6V-2078 Stud 2
5P-4807 Cap 2
G 138-7575 Link Bracket 2
1. Make sure that all parts of the final drive are thoroughly clean and free of dirt and debris
prior to assembly.
Note: Check the condition of all the O-ring seals that are used in the final drive. If any of
the seals are worn or damaged, use new parts for replacement.
2. Reassemble the final drive on wood blocks and Tooling (A).
Illustration 1 g00875656
3. Apply 5P-3931 Anti-Seize Compound to the surfaces that contact the bearing cones. Install
the bearing cone with a press. Raise the temperature of bearing (51) and install the bearing.
4. Apply 5P-3931 Anti-Seize Compound to the surfaces that contact pins (50). Install the pins.
Illustration 2 g00875674
2/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 5. Apply 5P-3931 Anti-Seize Compound to the surfaces that contact the two bearing cups.
Install bearing cups (48) and (49).
Illustration 3 g00875677
6. Use Tooling (B) and a suitable lifting device to install main housing (45) on motor housing
(39). The weight of the main housing is approximately 250 kg (550 lb).
Illustration 4 g00875859
7. Install bearing (46) and the bearing cone.
8. Use the following procedure to determine the bearing preload and the correct number of
shims.
3/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 5 g00603328
a. Use a depth micrometer in order to measure the step length of the coupling gear (42).
Take measurements at several different locations around the gear. Compute the
average of the measured dimensions and record the number. Call this Dimension (X).
Illustration 6 g00876170
Illustration 7 g00876133
b. Use Tooling (F) to apply a load of 10700 kPa (1550 psi) in order to seat the bearings.
A pressure of 10700 kPa (1550 psi) on the 3S-6224 Electric Hydraulic Pump Gp will
result in a pressure of 10000 kg (22050 lb) on the bearings. Rotate the housing in
order to seat the bearing. Reduce the load on the 3S-6224 Electric Hydraulic Pump
Gp to 4825 kPa (700 psi).
c. Rotate Tooling (F) by 90° and repeat Step 8.b.
d. Maintain the load on the bearings. Use a depth micrometer and measure the distance
between the top face of motor housing and the bearing cone. Take this measurement
in several locations around the bearing. Compute the average of the measured
dimensions and record the number. Call this Dimension (Y).
e. Determine the correct thickness of the shim pack that will be installed between the
bearing cone and the coupling gear. The shim pack thickness is equal to Dimension
(Y) minus Dimension (X). Tolerance for the shim pack is 0.1 mm (0.003 inch).
4/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Note: If two shims are required, install the thinner shim next to the coupling gear
when the coupling gear is installed.
9. Use Tooling (B) and a suitable lifting device to remove the main housing from the motor
housing. The weight of the main housing is approximately 250 kg (550 lb).
Note: Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contact the seals must be clean and dry. After
installation of the seals, apply clean SAE 30 oil on the contact surfaces of the metal seals.
Illustration 8 g00876775
10. Use Tooling (C) to install Duo-Cone seal (47) in the main housing.
Illustration 9 g00876788
11. Use Tooling (C) to install Duo-Cone seal (52) in the motor housing.
Note: Make sure that the Duo-Cone seals are not scratched or damaged during the assembly
of the main housing or during the assembly of the motor housing. After installation of the
main housing on the motor housing, there will be a small gap between the components. The
gap is caused by the Duo-Cone seals. The gap will be eliminated during installation of the
gear.
5/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 10 g00875677
12. Fasten Tooling (B) and a hoist to main housing (45). Place the main housing in position on
motor housing (39). Make sure that the Duo-Cone seals are not scratched or damaged
during installation. The weight of the main housing is approximately 250 kg (550 lb).
Illustration 11 g00876801
13. Install bearing (46) and the bearing cone.
Illustration 12 g00866072
6/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 13 g00866047
14. Place shims (43) in the correct position on the motor housing. If two shims were required,
put the thinner shim in contact with coupling gear (42). Make sure that all of the holes in the
components are in alignment with each other. Put coupling gear (42) in the original position
on the motor housing.
15. Apply 9S-3263 Thread Lock Compound on the threads of bolts (41). Install the bolts to
secure coupling gear (42) in place. Tighten the bolts evenly and tighten the bolts in
diagonally opposite pairs. Tighten bolts to a torque of 900 ± 100 N·m (665 ± 75 lb ft).
Illustration 14 g00865939
16. Install O-ring seal (40) in the main housing.
7/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 15 g00876919
17. Use Tooling (B) and a hoist to position housings (39) and (45) on Tooling (A). Remove the
wood blocks. The weight of both housings is approximately 430 kg (950 lb).
Illustration 16 g00876937
18. Thoroughly clean the mating surface of main housing (39) that contacts ring gear (38).
Apply a bead of 1U-8846 Gasket Sealant on the mating surface of ring gear (38). Use
Tooling (E) and a suitable lifting device. Place the ring gear in position on the main
housing. Make sure that the alignment mark on the main housing and the ring gear line up
with each other. It may be necessary to use a soft faced hammer to seat the ring gear on the
main housing.
19. Assemble carrier assembly (28), as follows:
Illustration 17 g00865884
8/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 18 g00865872
a. Apply clean SAE 30 oil on bearings (34) and (36). Install two bearings (34) and (36)
in planetary gear (35).
b. Install thrust washers (33) and (37) on each side of the planetary gear.
c. Install the planetary gear and thrust washers in carrier assembly (28).
d. Install planetary shaft (32) in carrier assembly (28) and through planetary gear
assembly (30). Make sure that the spring pin hole in the planetary shaft is in
alignment with the spring pin hole in the carrier.
Illustration 19 g00513451
e. Install spring pin (31) in the carrier and into the planetary shaft. Make sure that the
spring pin hole in the planetary shaft is in alignment with the spring pin hole in the
carrier.
f. Orient the split in spring pin (31) horizontally to the carrier. Align the split in the
spring pin to the left or to the right. Make a stake mark on each side of the spring pin
hole in the carrier. This will prevent the spring pin from falling out of the spring pin
9/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. hole. Each stake mark should be approximately 1.5 mm (0.06 inch) to 3.00 mm
(0.118 inch) from the outside diameter of the spring pin hole.
g. Repeat Steps 19.a through 19.f in order to install the other three planetary gears in
carrier assembly (28).
Illustration 20 g00865862
20. Fasten Tooling (E) and a hoist to carrier assembly (28). Put the carrier assembly in position
in the ring gear. It may be necessary to move the carrier assembly back and forth during
installation in order to ensure that all gears engage properly.
21. Install spacer (29).
22. Assemble carrier assembly (21), as follows:
Illustration 21 g00865753
a. Apply clean SAE 30 oil on bearing (26). Install bearing (26) in planetary gear (25).
b. Install thrust washers (27) on each side of the planetary gear.
c. Install the thrust washers and the planetary gear in carrier assembly (28).
10/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP3...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 22 g00865736
d. Install planetary shaft (24) in carrier assembly (28) and through the planetary gear
assembly. Make sure that the spring pin hole in the planetary shaft is in alignment
with the spring pin hole in the carrier.
Illustration 23 g00513451
e. Orient the split in the spring pin (22) horizontally to the carrier. Align the split in the
spring pin to the left or to the right. Make a stake mark on each side of the spring pin
hole in the carrier. This will prevent the spring pin from falling out of the spring pin
hole. Each stake mark should be approximately 1.5 mm (0.06 inch) to 3.00 mm
(0.118 inch) from the outside diameter of the spring pin hole.
f. Repeat Steps 22.a through 22.e in order to install the other two planetary gears in
carrier assembly (28).
11/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP3...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 24 g00865717
23. Install gear assembly (21), spacer (20), and retaining ring (19).
Illustration 25 g00865671
24. Use a hoist and Tooling (B) to install carrier assembly (18). The weight of the carrier
assembly is approximately 95 kg (210 lb).
Illustration 26 g00865614
25. Apply clean SAE 30 oil on bearing (16). Install washers (15) and bearing (16) in gear (17).
12/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP3...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 27 g00865551
26. Install gear assembly (12), shaft (14), and drive spring pin (13) into shaft (14).
27. Repeat Steps 25 and 26 for the remaining gear assemblies.
Illustration 28 g00865534
28. Install sun gear (11), spacer (10), and retaining ring (9).
Illustration 29 g00865501
29. Use a hoist and Tooling (B) to install carrier assembly (8). The weight of the carrier
assembly is approximately 43 kg (95 lb).
13/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP3...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 30 g00865487
30. Install sun gear (7).
Illustration 31 g00865183
31. Install the shims and spacer (4) in the cover.
32. Install ring gear (6) and socket head bolts (5) in the cover.
Illustration 32 g00865173
33. Use Tooling (B) and a suitable lifting device to position cover (2). Install bolts (3). The
weight of the cover is approximately 95 kg (210 lb).
14/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP3...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 33 g00865168
34. Remove the final drive from Tooling (A). The weight of the final drive is approximately
1020 kg (2250 lb).
End By:
a. Install the final drive. Refer to Disassembly and Assembly, "Final Drive - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 23 18:05:09 UTC+0800 2021
15/15
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP3...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Shutdown SIS
Previous Screen
Product: FRONT SHOVEL
Model: 5090B FRONT SHOVEL SJY
Configuration: 5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine
Disassembly and Assembly
385B and 5090B Excavators Excavator Systems
Media Number -RENR5407-06 Publication Date -01/02/2016 Date Updated -12/02/2016
i01698879
Final Drive - Install
SMCS - 4050-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
132-8223 Power Pack 1
132-8119 Hydraulic Torque Wrench Assembly 1
Note: The procedure to install the right hand final drive and the procedure to install the left hand
final drive is identical. The procedure that follows is for one of the final drives.
Illustration 1 g00874660
1/3
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. 1. Attach two lifting straps and a hoist to final drive (1). The weight of the final drive is
approximately 1020 kg (2250 lb). It may be necessary to adjust the lifting straps for correct
balance of the final drive. Position final drive (1) on the track roller frame.
Note: The weight of the final drive must be adjusted if any other components are being
installed with the final drive.
Illustration 2 g00874668
Illustration 3 g00874687
Note: Make sure that Mounting Holes (Z) for the travel motor are aligned. This is necessary
for the correct installation of the travel motor.
2. Use 9S-3263 Thread Lock Compound on bolts (2). Install bolts (2). Use Tooling (A) to
tighten bolts (2) to a torque of 1800 ± 200 N·m (1328 ± 148 lb ft).
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
b. Install the final drive sprocket. Refer to Disassembly and Assembly, "Final Drive Sprocket -
Remove and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Sat Jan 23 18:06:05 UTC+0800 2021
2/3
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Shutdown SIS
Previous Screen
Product: FRONT SHOVEL
Model: 5090B FRONT SHOVEL SJY
Configuration: 5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine
Disassembly and Assembly
385B and 5090B Excavators Excavator Systems
Media Number -RENR5407-06 Publication Date -01/02/2016 Date Updated -12/02/2016
i01673240
Coupling - Remove and Install
SMCS - 4199-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7576 Link Bracket 2
B Guide bolt (1/2 inch by 13 NC by 4 inch) 2
C 138-7575 Link Bracket 1
Start By:
a. Remove the main hydraulic pump. Refer to Disassembly and Assembly, "Main Hydraulic
Pump - Remove".
1/9
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP366...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading