This document provides instructions for installing a flywheel on a Caterpillar 434F backhoe loader engine. It describes cleaning and preparing the flywheel and crankshaft, installing guide bolts and lifting the flywheel into place with bolts finger tight before fully tightening. It also describes inspecting the flywheel runout after installation.
Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly0...jfjkskekfsmem
This document provides instructions for installing a flywheel on a 434F backhoe loader with a C4.4 engine. It describes cleaning and preparing the flywheel and crankshaft, installing guide bolts and lifting the flywheel into place with bolts finger tight before fully tightening. It also describes inspecting alignment and installing related components like the electric starting motor.
Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly0...ufdjjskefksmem
This document provides instructions for installing a flywheel on a 434F BACKHOE LOADER model powered by a C4.4 engine. The procedure involves installing a ring gear on the flywheel if it was removed, cleaning and preparing the crankshaft, lifting the flywheel into place using guide bolts, installing bolts and tightening them to the specified torque, and checking flywheel runout before reinstalling the electric starting motor.
Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly0...ufjsjekfksemm
This document provides instructions for installing a flywheel and flywheel housing on a Caterpillar C4.4 engine. It describes:
1) Cleaning and preparing the crankshaft, installing a new ring gear on the flywheel if needed, and lifting the flywheel into place using guide bolts before tightening the mounting bolts.
2) Checking the crankshaft rear seal for leaks, replacing if needed, and installing a new seal by aligning it with plastic sleeves and tightening mounting screws in the specified sequence.
3) Removing the flywheel housing by uninstalling mounting bolts and dowels, and lifting it away from the engine block using a hoist.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful due to the flywheel's weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing the guide bolts and tightening the bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal. The seal is not serviceable and must be replaced.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful due to the flywheel's weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing the guide bolts and tightening the bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal. The seal is not serviceable and must be replaced.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using punches.
3. Cleaning and positioning the flywheel for installation, adding bolts finger tight before final tightening.
4. Removing housing bolts and lifting the housing off the engine block using a lifting device. Inspection of seals is required before reinstallation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using a hammer and punch.
3. Cleaning and inspecting components, then positioning the flywheel for installation with guide bolts before tightening bolts to the specified torque.
4. Removing bolts and lifting the flywheel housing off the engine cylinder block after removing the flywheel. Inspecting components and reversing steps
Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly0...jfjkskekfsmem
This document provides instructions for installing a flywheel on a 434F backhoe loader with a C4.4 engine. It describes cleaning and preparing the flywheel and crankshaft, installing guide bolts and lifting the flywheel into place with bolts finger tight before fully tightening. It also describes inspecting alignment and installing related components like the electric starting motor.
Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly0...ufdjjskefksmem
This document provides instructions for installing a flywheel on a 434F BACKHOE LOADER model powered by a C4.4 engine. The procedure involves installing a ring gear on the flywheel if it was removed, cleaning and preparing the crankshaft, lifting the flywheel into place using guide bolts, installing bolts and tightening them to the specified torque, and checking flywheel runout before reinstalling the electric starting motor.
Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly0...ufjsjekfksemm
This document provides instructions for installing a flywheel and flywheel housing on a Caterpillar C4.4 engine. It describes:
1) Cleaning and preparing the crankshaft, installing a new ring gear on the flywheel if needed, and lifting the flywheel into place using guide bolts before tightening the mounting bolts.
2) Checking the crankshaft rear seal for leaks, replacing if needed, and installing a new seal by aligning it with plastic sleeves and tightening mounting screws in the specified sequence.
3) Removing the flywheel housing by uninstalling mounting bolts and dowels, and lifting it away from the engine block using a hoist.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful due to the flywheel's weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing the guide bolts and tightening the bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal. The seal is not serviceable and must be replaced.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful due to the flywheel's weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing the guide bolts and tightening the bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal. The seal is not serviceable and must be replaced.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using punches.
3. Cleaning and positioning the flywheel for installation, adding bolts finger tight before final tightening.
4. Removing housing bolts and lifting the housing off the engine block using a lifting device. Inspection of seals is required before reinstallation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using a hammer and punch.
3. Cleaning and inspecting components, then positioning the flywheel for installation with guide bolts before tightening bolts to the specified torque.
4. Removing bolts and lifting the flywheel housing off the engine cylinder block after removing the flywheel. Inspecting components and reversing steps
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using punches.
3. Cleaning and aligning the crankshaft flange before pressing the new crankshaft rear seal onto the flange using an alignment tool.
4. Removing bolts to lift the flywheel housing off the engine cylinder block using a lifting device. Inspection and installation steps are also
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment due to the flywheel's weight of approximately 155 pounds. For installing the flywheel, the instructions specify cleaning components, heating the ring gear, lifting the flywheel into place, and tightening bolts to the specified torque. Removing the crankshaft rear seal involves using a socket to remove screws, while installing requires aligning and pressing the new seal onto the crankshaft flange and torquing screws to the specified value.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it with guide bolts and lifting equipment, replacing bolts, and tightening them in sequence.
3) Removing the crankshaft rear seal by taking out torx screws and discarding the seal and housing assembly.
4) Installing the new crankshaft rear seal by aligning it on the crankshaft flange, installing torx
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment. It similarly describes removing the flywheel housing by taking out bolts and checking seals. Reinstallation involves cleaning, installing dowels or seals if needed, and torquing bolts with a lifting device and dial indicator used for alignment.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it with guide bolts and lifting equipment, replacing bolts and checking run out.
3) Removing the crankshaft rear seal by taking out torx screws and discarding the seal and housing assembly.
4) Installing the new crankshaft rear seal by aligning it on the crankshaft flange without lubrication, installing torx
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using a hammer and punch.
3. Cleaning and inspecting components, then positioning the flywheel for installation using guide bolts and lifting it into place before reinstalling bolts.
4. Removing bolts holding the flywheel housing in place and lifting it off the engine, then checking seals before reversing the process to
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
This document provides assembly instructions for a torque converter in a 730 articulated truck. It lists 34 steps to assemble the various components of the torque converter, including housings, bearings, seals, discs, and shafts. Personal protective equipment is required and cleanliness is emphasized throughout the assembly process. Torque specifications are provided for securing different fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a receiver sleeve tool by pressing in from the rear.
- Engine oil pan - removed by draining oil first, then removing bolts, studs, clips
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, pressing bearings in at the proper angles and depths, and torquing bolts to the specified values.
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and compression brake valve assembly. The procedures include illustrations of the components and multi-step instructions for removal and installation, including proper torque specifications. Safety precautions are provided where necessary.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C15 or C18 engine. It describes removing components like the crankshaft rear seal, electric starting motor, and rear power take-off. It then explains how to use lifting tools to remove the flywheel housing and reinstall it, replacing seals and tightening bolts in a specific sequence and torque range. Similar instructions are provided for removing and installing just the rear power take-off components.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hoses and wiring, draining fluid from the elbow, attaching a lifting device to the pump, and removing nuts and the pump. It also includes notes about marking disconnected parts for installation and preventing fluid loss.
This document provides assembly instructions for repairing the transmission of a 329DL excavator. It consists of 52 steps to assemble the transmission components in the correct order, including installing gaskets, bearings, pistons, seals, covers, and other parts into the pump housing. Precautions are provided for steps involving spring tension. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
This document provides instructions for removing and disassembling the drive shaft and scavenge pump on a 657G Wheel Scraper. Key steps include:
1. Removing retaining rings, covers, and guards to access the drive shaft.
2. Using eyebolts and lifting devices to remove the heavy drive shaft and tube assembly.
3. Checking alignment of components and removing the yoke assembly, bearings, and seals.
4. Disassembling the scavenge pump by removing O-rings, bearings, shafts, and gears.
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412C engines. The summary is:
1. The document outlines the required tools and safety procedures for removing the cylinder head, which involves detaching hoses, bolts, and lifting the heavy part off.
2. Instructions are provided for installing the new cylinder head gasket and reattaching the cylinder head using lifting brackets and torqueing the bolts in a specific sequence.
3. The lifter group removal process involves using a special tool to pull out the lifters and springs from the bores. Reinstallation requires aligning new springs and pressing the lifter assemblies back into place
More Related Content
Similar to Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instant Download.pdf
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using punches.
3. Cleaning and aligning the crankshaft flange before pressing the new crankshaft rear seal onto the flange using an alignment tool.
4. Removing bolts to lift the flywheel housing off the engine cylinder block using a lifting device. Inspection and installation steps are also
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment due to the flywheel's weight of approximately 155 pounds. For installing the flywheel, the instructions specify cleaning components, heating the ring gear, lifting the flywheel into place, and tightening bolts to the specified torque. Removing the crankshaft rear seal involves using a socket to remove screws, while installing requires aligning and pressing the new seal onto the crankshaft flange and torquing screws to the specified value.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it with guide bolts and lifting equipment, replacing bolts, and tightening them in sequence.
3) Removing the crankshaft rear seal by taking out torx screws and discarding the seal and housing assembly.
4) Installing the new crankshaft rear seal by aligning it on the crankshaft flange, installing torx
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment. It similarly describes removing the flywheel housing by taking out bolts and checking seals. Reinstallation involves cleaning, installing dowels or seals if needed, and torquing bolts with a lifting device and dial indicator used for alignment.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it with guide bolts and lifting equipment, replacing bolts and checking run out.
3) Removing the crankshaft rear seal by taking out torx screws and discarding the seal and housing assembly.
4) Installing the new crankshaft rear seal by aligning it on the crankshaft flange without lubrication, installing torx
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using a hammer and punch.
3. Cleaning and inspecting components, then positioning the flywheel for installation using guide bolts and lifting it into place before reinstalling bolts.
4. Removing bolts holding the flywheel housing in place and lifting it off the engine, then checking seals before reversing the process to
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
Similar to Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instant Download.pdf (12)
This document provides assembly instructions for a torque converter in a 730 articulated truck. It lists 34 steps to assemble the various components of the torque converter, including housings, bearings, seals, discs, and shafts. Personal protective equipment is required and cleanliness is emphasized throughout the assembly process. Torque specifications are provided for securing different fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a receiver sleeve tool by pressing in from the rear.
- Engine oil pan - removed by draining oil first, then removing bolts, studs, clips
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, pressing bearings in at the proper angles and depths, and torquing bolts to the specified values.
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and compression brake valve assembly. The procedures include illustrations of the components and multi-step instructions for removal and installation, including proper torque specifications. Safety precautions are provided where necessary.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C15 or C18 engine. It describes removing components like the crankshaft rear seal, electric starting motor, and rear power take-off. It then explains how to use lifting tools to remove the flywheel housing and reinstall it, replacing seals and tightening bolts in a specific sequence and torque range. Similar instructions are provided for removing and installing just the rear power take-off components.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hoses and wiring, draining fluid from the elbow, attaching a lifting device to the pump, and removing nuts and the pump. It also includes notes about marking disconnected parts for installation and preventing fluid loss.
This document provides assembly instructions for repairing the transmission of a 329DL excavator. It consists of 52 steps to assemble the transmission components in the correct order, including installing gaskets, bearings, pistons, seals, covers, and other parts into the pump housing. Precautions are provided for steps involving spring tension. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
This document provides instructions for removing and disassembling the drive shaft and scavenge pump on a 657G Wheel Scraper. Key steps include:
1. Removing retaining rings, covers, and guards to access the drive shaft.
2. Using eyebolts and lifting devices to remove the heavy drive shaft and tube assembly.
3. Checking alignment of components and removing the yoke assembly, bearings, and seals.
4. Disassembling the scavenge pump by removing O-rings, bearings, shafts, and gears.
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412C engines. The summary is:
1. The document outlines the required tools and safety procedures for removing the cylinder head, which involves detaching hoses, bolts, and lifting the heavy part off.
2. Instructions are provided for installing the new cylinder head gasket and reattaching the cylinder head using lifting brackets and torqueing the bolts in a specific sequence.
3. The lifter group removal process involves using a special tool to pull out the lifters and springs from the bores. Reinstallation requires aligning new springs and pressing the lifter assemblies back into place
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412C engines. The summary is:
1. The document outlines the required tools and safety procedures for removing the cylinder head, which involves detaching hoses, bolts, and lifting the heavy part off.
2. Instructions are provided for installing the new cylinder head gasket and reattaching the cylinder head using lifting brackets and torqueing the bolts in a specific sequence.
3. The lifter group removal process involves using a special tool to pull out the lifters and springs from the bores. Reinstallation requires aligning new springs and pressing the lifter assemblies back into place
The document provides instructions for disassembling and assembling a recoil spring assembly. Key steps include:
1. Using a specialized tooling bench to securely hold the recoil spring assembly, which is under several tons of force.
2. Carefully removing a nut to release the spring tension before disassembling the recoil spring components.
3. Reassembling the recoil spring components and using the tooling bench to apply controlled compression for assembly. Proper centering and leveling of the assembly is critical.
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar 657E wheel tractor. The removal procedure involves using various tools to disassemble the rear gear components and adapter assemblies. The installation procedure describes reassembling these components and requires pressing or installing bearings and seals using a driver group or press. Special care must be taken to keep parts clean and lubricated. The flywheel removal uses tools to secure the crankshaft gear and hoist the heavy flywheel off the engine.
This document provides instructions for installing and removing various engine components on a Caterpillar 657E wheel scraper model powered by a 3408 engine, including:
1) Installing the rear gear group by placing gears and bearings on shafts and installing dowels, seals and bolts.
2) Removing the flywheel using guide bolts, brackets and a hoist to lift the heavy flywheel off the crankshaft.
3) Installing the flywheel by heating the ring gear, placing the flywheel on guide bolts, and bolting it into place.
4) Procedures for removing and installing the crankshaft rear seal using punch tools or pullers
The document provides instructions for installing the crankshaft rear seal on a Caterpillar 657E wheel scraper. It describes heating the ring gear to 300°C before installing it on the flywheel. It also details installing guide bolts and lifting brackets to position the flywheel, applying grease to the bolt threads, and torquing the bolts to secure the flywheel. Finally, it notes to check the flywheel runout after installation.
This document provides step-by-step instructions for disassembling the pump control and pump housing of a 329DL excavator. It lists 60 steps to remove components like bolts, seals, pins, plates, barrels and shafts. Cleaning is important before disassembly to prevent dirt from entering mechanisms. The right pump control has a proportional reducing valve not present on the left. Tools are required to remove some components like bearings.
This document provides repair instructions for a 329DL excavator transmission. It outlines 38 steps to disassemble and reassemble the transmission, including instructions to clean parts, replace seals and O-rings, measure bearing clearance using shims, and install various transmission components like gears, seals, and housing pieces. Special tools are required for tasks like installing duo-cone seals and bearing surfaces must be coated with anti-seize compound before assembly.
This document provides instructions for disassembling and assembling the transmission transfer gears of a Caterpillar 651E wheel tractor. The steps include removing the transmission transfer gears as a unit, disassembling the individual gears and bearings, inspecting and replacing parts, and reassembling the gears and bearings in the correct order with the specified torques and clearances. Precautions are provided such as cleaning and lubricating parts during assembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes the required tools and multi-step processes for both removing the camshaft from the front or rear of the engine and installing a new camshaft. Precautions are outlined to prevent damage and contain fluids. The document is intended as a service repair manual for technicians performing camshaft maintenance on this model.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...8foskkdjdkdm3e
This document provides instructions for disassembling and assembling various components of a 651B wheel scraper model, including:
1. The engine transfer gear and retarder, with steps to remove gears, bearings, and housing pieces.
2. The transmission transfer gear, with steps to remove gears, bearings, pumps, and the governor.
3. The transmission governor, with identification of parts and steps to disassemble and reassemble the governor valve bodies.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i07030539
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Bolt
(1/2 inch - 20 UNF by 4 inch)
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01343963
Typical example
Always wear protective gloves when handling parts that have been
heated.
1. If the flywheel ring gear was removed, follow Steps 1.a through 1.c to install a new ring
gear to the flywheel.
a. Identify the orientation of teeth (4) on the new ring gear (4).
Note: The chamfered side of the ring gear teeth must face toward the starting motor
when the flywheel is installed. The correct orientation of the chamfered will ensure
the correct engagement of the starting motor.
b. Heat flywheel ring gear (3) in an oven to a maximum temperature of 250 °C (482 °F)
prior to installation.
Note: Do not use a torch to heat the ring gear.
c. Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear
onto flywheel (1).
2. Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft
rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" for the
correct procedure.
2/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01245126
Typical example
3. Install a suitable lifting device to flywheel (1). The flywheel weighs approximately 71 kg
(155 lb).
4. Install Tooling (A) to positions (X) on the crankshaft.
5. Use the lifting device to position flywheel (1) onto Tooling (A).
6. Install bolts (2) to flywheel (1) finger tight.
7. Remove Tooling (A) and install remaining bolts (2) to flywheel (1).
8. Remove the lifting device from flywheel (1).
9. Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) to a torque of
140 N·m (103 lb ft).
10. Check the run out of the flywheel. Refer to System Operation, Test, and Adjusting,
"Flywheel - Inspect" for further information.
End By:
a. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
3/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763427
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4390 E12 Torx Socket 1
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Dispose of all fluids according to local regulations and mandates.
Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly. The
assembly is not serviceable. If the crankshaft rear seal is removed, the assembly must be replaced.
Illustration 1 g01269512
Typical example
1. Use Tooling (A) in order to remove torx screws (1) from crankshaft rear seal (2).
2. Remove crankshaft rear seal (2) from the cylinder block. Discard the crankshaft rear seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 20 09:01:38 UTC+0800 2019
2/2
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763428
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4390 E12 Torx Socket 1
B FT-2806 Alignment Tool 1
Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g01258105
Illustration 2 g01255709
Typical example
1. Ensure that crankshaft flange (1) is clean, dry and free from damage.
2. Ensure that the face of the cylinder block and the bridge piece are clean and dry.
3. A new crankshaft rear seal is supplied with a plastic sleeve (3). Ensure that the plastic
sleeve is squarely installed within crankshaft rear seal (2).
Note: The plastic sleeve is included in order to protect the lip of the seal as the seal is
pushed over the crankshaft flange.
Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The
crankshaft rear seal must be installed dry.
2/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 4. Align plastic sleeve (3) with crankshaft flange (1). Ensure that the plastic sleeve is engaged
onto the crankshaft flange. Push new crankshaft rear seal (2) squarely onto the crankshaft
flange.
During this process, the plastic sleeve will be forced out of the crankshaft rear seal. Discard
the plastic sleeve.
5. Align the two molded locators on crankshaft rear seal (2) with the holes in the cylinder
block. Ensure that the crankshaft rear seal is seated against the cylinder block.
Illustration 3 g01258357
Tightening sequence for the crankshaft rear seal
6. Install torx screws (4) finger tight.
Note: Do not install torx screws to positions (X) at this stage.
7. Install Tooling (B) to crankshaft rear seal (2) and to crankshaft flange (1).
8. Use Tooling (A) in order to tighten torx screws (4) to a torque of 22 N·m (16 lb ft). Tighten
torx screws (4) in the sequence that is shown in Illustration 3.
9. Remove Tooling (B).
10. Install remaining torx screws (4) to positions (X). Use Tooling (A) in order to tighten the
torx screws to a torque of 22 N·m (16 lb ft). Refer to Illustration 3.
3/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 20 09:02:34 UTC+0800 2019
4/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763429
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Install a suitable lifting device to the flywheel housing in order to support the flywheel
housing. The flywheel housing weighs approximately 30 kg (66 lb).
1/5
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g01244050
Typical example
2. Remove bolts (2) and bolts (3) from flywheel housing (1).
3. Use the lifting device in order to remove flywheel housing (1) from the cylinder block.
Illustration 2 g01244051
2/5
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Typical example
4. If the engine has an aluminum oil pan, remove dust seal (5).
5. If necessary, remove dowels (4) from the cylinder block.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
(M10 by 100 mm)
2
B 8T-5096 Dial Indicator Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the flywheel housing is clean and free from damage. If necessary, replace the
flywheel housing.
Illustration 3 g01244056
Typical example
3/5
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 2. Inspect crankshaft rear seal (6) for leaks. If there are any oil leaks, replace the crankshaft
rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and refer
to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
3. Clean the rear face of the cylinder block. If necessary, install dowels (4) to the cylinder
block.
4. Install Tooling (A) to the cylinder block.
5. Install dust seal (5).
Illustration 4 g01244050
Typical example
6. Install a suitable lifting device to the flywheel housing. The flywheel housing weighs
approximately 30 kg (66 lb).
7. Use the lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel
housing to the cylinder block.
8. Install bolts (2) and bolts (3) finger tight.
9. Remove Tooling (A). Install remaining bolts (3).
10. Tighten bolts (3) to a torque of 63 N·m (46 lb ft).
11. Tighten bolts (2) to a torque of 75 N·m (55 lb ft).
4/5
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 12. Use Tooling (B) to check the alignment of the flywheel housing with the crankshaft. Refer
to Systems Operation, Testing and Adjusting, "Flywheel Housing - Inspect".
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 20 09:03:30 UTC+0800 2019
5/5
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763430
Crankshaft Pulley - Remove and Install - Engines Without an
Automatic Belt Tensioner
SMCS - 1205-010
Removal Procedure
Start By:
a. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01255707
1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove bolts (1).
2. Remove thrust block (2).
3. Carefully remove crankshaft pulley (3) from the crankshaft.
Installation Procedure
Illustration 2 g01255707
1. Ensure that the crankshaft pulley and the thrust block are clean and free from damage.
Replace any components that are damaged. It is possible to reclaim a crankshaft pulley with
2/3
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. a worn seal surface by installing a wear sleeve. Refer to Disassembly and Assembly,
"Crankshaft Wear Sleeve (Front) - Remove and Install".
2. Ensure that the front of the crankshaft is clean and free from damage. Install crankshaft
pulley (3) to the crankshaft.
Illustration 3 g01390496
3. Align the holes in thrust block (2) with the holes in the crankshaft.
Note: Ensure chamfered holes (X) in thrust block (2). Face toward the front of the engine.
4. Install thrust block (2) to the assembly of the crankshaft pulley.
5. Install bolts (1) to thrust block (2).
6. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten the bolts evenly
to a torque of 115 N·m (85 lb ft).
7. Repeat Step 6 one more times in order to ensure correct torque.
End By:
a. Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 20 09:04:25 UTC+0800 2019
3/3
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763431
Crankshaft Pulley - Remove and Install - Engines With an
Automatic Belt Tensioner
SMCS - 1205-010
Removal Procedure
Start By:
a. Remove the Alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g01249049
1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove bolts (1).
2. Remove thrust block (2).
3. Carefully remove the assembly of the crankshaft pulley from the crankshaft.
4. Follow Steps 4.a through 4.b in order to disassemble the crankshaft pulley.
a. Remove bolts (5).
b. Remove crankshaft pulley (4) from crankshaft adapter (3).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
22. 1. Ensure that the crankshaft adapter, the pulley and the thrust block are clean and free from
damage. Replace any components that are damaged. It is possible to reclaim a crankshaft
adapter with a worn seal surface by installing a wear sleeve. Refer to Disassembly and
Assembly, "Crankshaft Wear Sleeve (Front) - Remove and Install".
Illustration 2 g01367385
2. If necessary, follow Steps 2.a through 2.b in order to assemble the crankshaft pulley.
a. Install crankshaft pulley (4) to crankshaft adapter (3).
b. Install bolts (5) to the assembly of the crankshaft pulley, and the crankshaft adapter.
The bolts should be evenly spaced.
c. Tighten the bolts to a torque of 78 N·m (58 lb ft).
3. Ensure that the front of the crankshaft is clean and free from damage. Install the assembly of
the crankshaft pulley to the crankshaft.
3/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...