This document provides instructions for installing a flywheel and flywheel housing on a Caterpillar C4.4 engine. It describes:
1) Cleaning and preparing the crankshaft, installing a new ring gear on the flywheel if needed, and lifting the flywheel into place using guide bolts before tightening the mounting bolts.
2) Checking the crankshaft rear seal for leaks, replacing if needed, and installing a new seal by aligning it with plastic sleeves and tightening mounting screws in the specified sequence.
3) Removing the flywheel housing by uninstalling mounting bolts and dowels, and lifting it away from the engine block using a hoist.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i07030539
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Bolt
(1/2 inch - 20 UNF by 4 inch)
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01343963
Typical example
Always wear protective gloves when handling parts that have been
heated.
1. If the flywheel ring gear was removed, follow Steps 1.a through 1.c to install a new ring
gear to the flywheel.
a. Identify the orientation of teeth (4) on the new ring gear (4).
Note: The chamfered side of the ring gear teeth must face toward the starting motor
when the flywheel is installed. The correct orientation of the chamfered will ensure
the correct engagement of the starting motor.
b. Heat flywheel ring gear (3) in an oven to a maximum temperature of 250 °C (482 °F)
prior to installation.
Note: Do not use a torch to heat the ring gear.
c. Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear
onto flywheel (1).
2. Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft
rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" for the
correct procedure.
2/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01245126
Typical example
3. Install a suitable lifting device to flywheel (1). The flywheel weighs approximately 71 kg
(155 lb).
4. Install Tooling (A) to positions (X) on the crankshaft.
5. Use the lifting device to position flywheel (1) onto Tooling (A).
6. Install bolts (2) to flywheel (1) finger tight.
7. Remove Tooling (A) and install remaining bolts (2) to flywheel (1).
8. Remove the lifting device from flywheel (1).
9. Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) to a torque of
140 N·m (103 lb ft).
10. Check the run out of the flywheel. Refer to System Operation, Test, and Adjusting,
"Flywheel - Inspect" for further information.
End By:
a. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
3/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763427
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4390 E12 Torx Socket 1
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Dispose of all fluids according to local regulations and mandates.
Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly. The
assembly is not serviceable. If the crankshaft rear seal is removed, the assembly must be replaced.
Illustration 1 g01269512
Typical example
1. Use Tooling (A) in order to remove torx screws (1) from crankshaft rear seal (2).
2. Remove crankshaft rear seal (2) from the cylinder block. Discard the crankshaft rear seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 20 09:01:38 UTC+0800 2019
2/2434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763428
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4390 E12 Torx Socket 1
B FT-2806 Alignment Tool 1
Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g01258105
Illustration 2 g01255709
Typical example
1. Ensure that crankshaft flange (1) is clean, dry and free from damage.
2. Ensure that the face of the cylinder block and the bridge piece are clean and dry.
3. A new crankshaft rear seal is supplied with a plastic sleeve (3). Ensure that the plastic
sleeve is squarely installed within crankshaft rear seal (2).
Note: The plastic sleeve is included in order to protect the lip of the seal as the seal is
pushed over the crankshaft flange.
Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The
crankshaft rear seal must be installed dry.
2/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 4. Align plastic sleeve (3) with crankshaft flange (1). Ensure that the plastic sleeve is engaged
onto the crankshaft flange. Push new crankshaft rear seal (2) squarely onto the crankshaft
flange.
During this process, the plastic sleeve will be forced out of the crankshaft rear seal. Discard
the plastic sleeve.
5. Align the two molded locators on crankshaft rear seal (2) with the holes in the cylinder
block. Ensure that the crankshaft rear seal is seated against the cylinder block.
Illustration 3 g01258357
Tightening sequence for the crankshaft rear seal
6. Install torx screws (4) finger tight.
Note: Do not install torx screws to positions (X) at this stage.
7. Install Tooling (B) to crankshaft rear seal (2) and to crankshaft flange (1).
8. Use Tooling (A) in order to tighten torx screws (4) to a torque of 22 N·m (16 lb ft). Tighten
torx screws (4) in the sequence that is shown in Illustration 3.
9. Remove Tooling (B).
10. Install remaining torx screws (4) to positions (X). Use Tooling (A) in order to tighten the
torx screws to a torque of 22 N·m (16 lb ft). Refer to Illustration 3.
3/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 20 09:02:34 UTC+0800 2019
4/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763429
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Install a suitable lifting device to the flywheel housing in order to support the flywheel
housing. The flywheel housing weighs approximately 30 kg (66 lb).
1/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g01244050
Typical example
2. Remove bolts (2) and bolts (3) from flywheel housing (1).
3. Use the lifting device in order to remove flywheel housing (1) from the cylinder block.
Illustration 2 g01244051
2/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Typical example
4. If the engine has an aluminum oil pan, remove dust seal (5).
5. If necessary, remove dowels (4) from the cylinder block.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
(M10 by 100 mm)
2
B 8T-5096 Dial Indicator Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the flywheel housing is clean and free from damage. If necessary, replace the
flywheel housing.
Illustration 3 g01244056
Typical example
3/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 2. Inspect crankshaft rear seal (6) for leaks. If there are any oil leaks, replace the crankshaft
rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and refer
to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
3. Clean the rear face of the cylinder block. If necessary, install dowels (4) to the cylinder
block.
4. Install Tooling (A) to the cylinder block.
5. Install dust seal (5).
Illustration 4 g01244050
Typical example
6. Install a suitable lifting device to the flywheel housing. The flywheel housing weighs
approximately 30 kg (66 lb).
7. Use the lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel
housing to the cylinder block.
8. Install bolts (2) and bolts (3) finger tight.
9. Remove Tooling (A). Install remaining bolts (3).
10. Tighten bolts (3) to a torque of 63 N·m (46 lb ft).
11. Tighten bolts (2) to a torque of 75 N·m (55 lb ft).
4/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 12. Use Tooling (B) to check the alignment of the flywheel housing with the crankshaft. Refer
to Systems Operation, Testing and Adjusting, "Flywheel Housing - Inspect".
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 20 09:03:30 UTC+0800 2019
5/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763430
Crankshaft Pulley - Remove and Install - Engines Without an
Automatic Belt Tensioner
SMCS - 1205-010
Removal Procedure
Start By:
a. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01255707
1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove bolts (1).
2. Remove thrust block (2).
3. Carefully remove crankshaft pulley (3) from the crankshaft.
Installation Procedure
Illustration 2 g01255707
1. Ensure that the crankshaft pulley and the thrust block are clean and free from damage.
Replace any components that are damaged. It is possible to reclaim a crankshaft pulley with
2/3434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. a worn seal surface by installing a wear sleeve. Refer to Disassembly and Assembly,
"Crankshaft Wear Sleeve (Front) - Remove and Install".
2. Ensure that the front of the crankshaft is clean and free from damage. Install crankshaft
pulley (3) to the crankshaft.
Illustration 3 g01390496
3. Align the holes in thrust block (2) with the holes in the crankshaft.
Note: Ensure chamfered holes (X) in thrust block (2). Face toward the front of the engine.
4. Install thrust block (2) to the assembly of the crankshaft pulley.
5. Install bolts (1) to thrust block (2).
6. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten the bolts evenly
to a torque of 115 N·m (85 lb ft).
7. Repeat Step 6 one more times in order to ensure correct torque.
End By:
a. Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 20 09:04:25 UTC+0800 2019
3/3434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763431
Crankshaft Pulley - Remove and Install - Engines With an
Automatic Belt Tensioner
SMCS - 1205-010
Removal Procedure
Start By:
a. Remove the Alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g01249049
1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove bolts (1).
2. Remove thrust block (2).
3. Carefully remove the assembly of the crankshaft pulley from the crankshaft.
4. Follow Steps 4.a through 4.b in order to disassemble the crankshaft pulley.
a. Remove bolts (5).
b. Remove crankshaft pulley (4) from crankshaft adapter (3).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 1. Ensure that the crankshaft adapter, the pulley and the thrust block are clean and free from
damage. Replace any components that are damaged. It is possible to reclaim a crankshaft
adapter with a worn seal surface by installing a wear sleeve. Refer to Disassembly and
Assembly, "Crankshaft Wear Sleeve (Front) - Remove and Install".
Illustration 2 g01367385
2. If necessary, follow Steps 2.a through 2.b in order to assemble the crankshaft pulley.
a. Install crankshaft pulley (4) to crankshaft adapter (3).
b. Install bolts (5) to the assembly of the crankshaft pulley, and the crankshaft adapter.
The bolts should be evenly spaced.
c. Tighten the bolts to a torque of 78 N·m (58 lb ft).
3. Ensure that the front of the crankshaft is clean and free from damage. Install the assembly of
the crankshaft pulley to the crankshaft.
3/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...