Caterpillar cat 434 e backhoe loader (prefix sjl) service repair manual (sjl00001 and up)

Service Repair Manual
Model
434E BACKHOE LOADER

Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434E BACKHOE LOADER SJL
Configuration: 434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train
Media Number -KENR8841-01 Publication Date -01/05/2014 Date Updated -14/05/2014
i03625932
Transmission (Power Shift) - Assemble
SMCS - 3030-016-PM; 3066-016
S/N - EME1-UP
S/N - JBA1-UP
S/N - NBA1-UP
S/N - SJL1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7502 Transmission Repair Stand 1
B 138-7575 Link Bracket 1
C
152-7085 (1)
Transmission Shaft Handler 1
189-0409 Shackle As 1
G 152-7055 Spring Compressor 1
H 2P-8312 Retaining Ring Pliers 1
J 8T-5096 Dial Indicator Gp 1
K 6V-6640 Sealant -
L 9S-3263 Thread Lock Compound -
M 1U-6396 O-Ring Assembly Compound -
1/41434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

( 1 )
CE Compliant
Note: The transmission will be assembled in major components. The major components will then
be assembled.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Note: Apply a light film of clean transmission oil to all components before assembly.
Note: O-ring seals, gaskets, and seals should always be replaced. A used O-ring seal may not have
the same sealing properties as a new O-ring seal. Use Tooling (M) during the assembly procedure.
Illustration 1 g00731364
1. During the installation of all the needle bearings on the shafts, the open end of cups (1) must
point away from the bearings or gears that are contacted.
Reverse Shaft

1. Install piston (17) .
2. Install spring assembly (15) .

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
3. Use a suitable press and Tooling (G) in order to compress spring assembly (15). Use
Tooling (H) in order to install retaining ring (16) .
4. Install friction discs (13) and plates (14) .

5. Install end plate (12) and retaining ring (11) .
6. Install thrust washer (8), needle bearing (9) and roller bearing (10) .

7. Install gear (4). Install roller bearing (5), needle bearing (6), and thrust washer (7). Raise the
temperature of bearing cone (3). Install bearing cone (3) .
8. Install seal rings (1) onto reverse shaft (2) .

9. Raise the temperature of bearing cone (18). Install bearing cone (18) .
Input Shaft

injury.
4. Install discs (31) and plates (32) .

6. Install thrust washer (28) and needle bearing (27). Install roller bearings (25) and (26) .
7. Install gear (24) .

8. Install needle bearing (23) and thrust washer (22) .
10. Install ring (20) .
10/41434E Backhoe Loader SJL00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...

injury.

13. Use Tooling (G) and a suitable press in order to compress spring assembly (17). Use
14. Install discs (15) and plates (16) .
15. Install retaining ring (13) and end plate (14) .

16. Install thrust washer (8), needle bearing (9), roller bearing (10), spacer (11), and roller
bearing (12) .
17. Install gear (7), needle bearing (6), and thrust washer (5) .

18. Install retaining ring (4) .
20. Install seal rings (1) onto input shaft (2) .
Countershaft

injury.
3. Use Tooling (G) and a suitable press in order to compress spring assembly (19). Use

6. Install thrust washer (14) and needle bearing (13). Install roller bearings (11) and (12) .
7. Install gear (10) .

8. Install needle bearing (9) and thrust washer (8) .
10. Install seal rings (6) .

11. Raise the temperature of gears (4) and (5). Install gears (4) and (5) .

13. Install washer (2) and bolt (1) .
Output Shaft (Rear)

injury.

6. Install thrust washer (20), needle bearing (21), roller bearing (22), spacer (23) and roller
bearing (24) .

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

7. Raise the temperature of gear (19). Install gear (19) .

injury.
11. Use a suitable press and Tooling (G) in order to compress spring assembly (15) and use

14. Install thrust washer (10), needle bearing (9) and roller bearing (8) .

15. Install gear (4), roller bearing (5), needle bearing (6) and thrust washer (7). Raise the
temperature of bearing cone (3). Install bearing cone (3) .
16. Install seal rings (1) and (2) .
Output Shaft (Front)

Caterpillar cat 434 e backhoe loader (prefix sjl) service repair manual (sjl00001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (6)

Similar to Caterpillar cat 434 e backhoe loader (prefix sjl) service repair manual (sjl00001 and up)

Similar to Caterpillar cat 434 e backhoe loader (prefix sjl) service repair manual (sjl00001 and up) (20)

More from ujdfjjkskkmmde

More from ujdfjjkskkmmde (17)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 434 e backhoe loader (prefix sjl) service repair manual (sjl00001 and up)