This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and gives step-by-step procedures for both removing and installing the seal. The procedures are different depending on whether the engine has a 14 bolt housing assembly or a 10 bolt housing assembly. Pictures and part numbers are provided to support the instructions.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjeskfksmefmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fusjejfjskekemm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear.
2) Install the flywheel by heating the ring gear, installing it on the flywheel, positioning the flywheel and installing bolts while using lifting tools.
3) Remove the crankshaft rear seal by removing housing bolts and hardware.
4) Install the crankshaft rear seal by cleaning parts, installing the seal, lubricating, positioning
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
This document provides assembly instructions for the transmission of a 434E BACKHOE LOADER model. It lists the required tools and notes on cleanliness and lubrication. It then provides step-by-step instructions with illustrations for assembling the various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft (rear). Proper compression of springs and installation of seals, bearings, gears and other parts is described.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
This document provides instructions for disassembling and removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support tubes to lift the front and rear of the machine, draining the transmission fluid.
2) Removing mounting bolts, brackets and hoses to separate the transmission from the engine and rear axle housing.
3) Using overhead lift equipment to remove the transmission once it is fully separated from the machine.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjeskfksmefmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fusjejfjskekemm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear.
2) Install the flywheel by heating the ring gear, installing it on the flywheel, positioning the flywheel and installing bolts while using lifting tools.
3) Remove the crankshaft rear seal by removing housing bolts and hardware.
4) Install the crankshaft rear seal by cleaning parts, installing the seal, lubricating, positioning
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
This document provides assembly instructions for the transmission of a 434E BACKHOE LOADER model. It lists the required tools and notes on cleanliness and lubrication. It then provides step-by-step instructions with illustrations for assembling the various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft (rear). Proper compression of springs and installation of seals, bearings, gears and other parts is described.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
This document provides instructions for disassembling and removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support tubes to lift the front and rear of the machine, draining the transmission fluid.
2) Removing mounting bolts, brackets and hoses to separate the transmission from the engine and rear axle housing.
3) Using overhead lift equipment to remove the transmission once it is fully separated from the machine.
The document provides instructions for disassembling and removing various components of a 432F2 backhoe loader, including the axle housing, brake assembly, differential and bevel gear, solenoid valve, and releasing system pressure. Key steps include using various tools to remove bearings, gears, pins, seals, and other parts. Precautions are outlined for releasing spring pressure safely.
This document provides disassembly instructions for the transmission of a 432E Backhoe Loader. It lists required tools and outlines 14 steps to fully disassemble the transmission. These include removing various gears, shafts, seals, bearings and other components from the front output shaft, rear output shaft, countershaft, idler shaft, and input shaft. Special care and tools are noted for removing springs and releasing pressurized components. The goal is to break down the transmission into its core individual parts for maintenance or replacement.
The document provides instructions for removing and disassembling the transmission of a 432D backhoe loader. It lists the required tools and gives step-by-step instructions to drain the transmission oil, remove mounting bolts, disconnect electrical connectors, and use lifting tools to safely remove the transmission. Cleanliness is emphasized when disassembling internal components to prevent dirt contamination.
This document provides instructions for removing and installing an engine on a 432E Backhoe Loader. It outlines 50 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses and hoses, and removing mounting hardware. Tools required are listed. To install the engine, the 50 removal steps are reversed, taking care when connecting wiring harnesses and positioning mounting bolts. Proper lifting equipment is needed due to the engine weighing approximately 454 kg.
The document provides instructions for removing an engine oil cooler from a 432D BACKHOE LOADER, which includes draining fluids, removing housing bolts and seals, and removing the oil cooler. It then provides instructions for installing a new oil cooler, which includes cleaning surfaces, installing new seals and bolts, and refilling fluids. Separate instructions are given for removing and installing an engine oil relief valve.
This document provides instructions for installing an engine in a 430F2 backhoe loader. It describes lifting the engine into place using load leveling beams, aligning and bolting the bell housing and flywheel, installing engine mounts and accessories like the starter motor, alternator, and air conditioning compressor, and filling fluids like coolant and oil. The final steps include installing panels and covers to complete the engine installation.
This service repair manual provides instructions for removing and installing exhaust manifolds and inlet manifolds on Caterpillar 3054 engines. It describes removing manifold bolts and nuts, removing gaskets, cleaning parts, installing new gaskets, reinstalling manifolds and tightening bolts or nuts to the specified torque for both type 1, type 2 and 7BJ engines. The document is from the Caterpillar Service Information System and provides detailed step-by-step instructions and illustrations for mechanics performing maintenance on Caterpillar equipment.
The document provides instructions for removing and installing a crankshaft rear seal and flywheel housing on a Caterpillar 430F2 backhoe loader. It describes using various tools to remove torx screws and seals, cleaning parts, installing a new seal with a plastic sleeve, and tightening bolts to specified torques. The instructions are part of a service manual for maintenance and repair of engine components.
This document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 430F2 backhoe loader with a C4.4 engine. It outlines the necessary tools and describes a 7 step process for removal and a 9 step process for installation. Safety notices are included to keep parts clean and prevent damage during the procedure.
This document provides instructions for removing and installing a hydraulic tank on a 430F backhoe loader. The removal procedure involves disconnecting hoses from the tank, removing clamps, and taking out bolts to detach the tank assembly. Components like a strainer and gauge are then removed from the tank. Reinstallation involves reversing these steps and reattaching all hoses, clamps, and bolts.
This document provides instructions for removing and installing the front gear group of a C4.4 engine. The procedure involves:
1. Locking the crankshaft and camshaft in position using timing pins.
2. Marking the gears to ensure proper reinstallation.
3. Removing the fuel pump, camshaft, and idler gears.
4. Cleaning and inspecting the gear components.
5. Reinstalling the gears, ensuring proper timing and backlash measurements.
The document provides instructions for disassembling and assembling the direct drive transmission of a 430E Backhoe Loader. It lists required tools and gives step-by-step instructions to remove components such as gears, bearings, seals, and shafts. It describes using various tools to press, pull, or remove parts. Reassembly is to be done in major components and with a focus on cleanliness.
The document provides instructions for removing a hydraulic tank from a 428E BACKHOE LOADER. It involves draining the hydraulic oil, removing various panels and covers, and disconnecting hoses and harnesses. Key steps include removing bolts and panels to access the tank, then disconnecting multiple hose assemblies and a harness connecting to the tank before it can be lifted out. The process requires draining fluid first and removes parts in a specific sequence for access.
This document provides instructions for removing and installing various components of a Caterpillar 3054C diesel engine, including:
- Lifter group removal and installation
- Camshaft removal and installation
- Camshaft bearing removal and installation
- Engine oil pan removal and installation
The summaries include detailed step-by-step instructions, required tools, safety notices, and references to other relevant sections for complete disassembly and reassembly. Precautions are outlined to prevent contamination and damage to parts.
This document provides instructions for removing and installing fuel injection nozzles and the fuel injection pump on a Caterpillar 3054 engine. It describes in detail:
- Removing fuel injection lines before removing nozzles or pump
- Using timing pins to ensure proper alignment when removing the pump
- Cleaning parts and applying anti-seize compound when installing nozzles
- Torque specifications for reinstalling nozzles and pump components
The document is from a service repair manual and contains detailed step-by-step instructions and illustrations for working on specific engine systems.
The document provides instructions for removing and disassembling the transmission of a 428D backhoe loader. It describes 19 steps to disassemble the transmission into its major components, including removing valve groups, filters, seals, shafts, and other parts. Special tools are required and care must be taken to contain fluids. The transmission weighs 172 kg and its components require lifting devices and stands for removal and handling.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for disassembling the transmission of a 428D backhoe loader. It describes removing the transmission from the machine and then disassembling the major transmission components. These include removing the output shafts on the front and rear of the transmission, along with the input shaft. Bearings and gears are then removed from each shaft. The transmission case is also disassembled by removing bearing cups. Tools required for disassembly are listed.
The document provides instructions for disassembling and assembling the steering metering pump of a 428D Backhoe Loader. It describes 18 steps to disassemble the pump by removing components like end caps, seals, springs, and fittings. It also lists 3 steps for assembling the pump, including installing fittings, seals, and bushings. Personal safety precautions are provided regarding hydraulic pressure and fluid containment.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles or pumps
- Using tools like pins and pullers to remove nozzles and pumps while ensuring proper timing
- Cleaning parts and applying anti-seize compound when installing nozzles
- Tightening nozzles and bolts on pumps to specified torques
- Ensuring number 1 cylinder is at top center when removing components
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
The document provides instructions for disassembling and removing various components of a 432F2 backhoe loader, including the axle housing, brake assembly, differential and bevel gear, solenoid valve, and releasing system pressure. Key steps include using various tools to remove bearings, gears, pins, seals, and other parts. Precautions are outlined for releasing spring pressure safely.
This document provides disassembly instructions for the transmission of a 432E Backhoe Loader. It lists required tools and outlines 14 steps to fully disassemble the transmission. These include removing various gears, shafts, seals, bearings and other components from the front output shaft, rear output shaft, countershaft, idler shaft, and input shaft. Special care and tools are noted for removing springs and releasing pressurized components. The goal is to break down the transmission into its core individual parts for maintenance or replacement.
The document provides instructions for removing and disassembling the transmission of a 432D backhoe loader. It lists the required tools and gives step-by-step instructions to drain the transmission oil, remove mounting bolts, disconnect electrical connectors, and use lifting tools to safely remove the transmission. Cleanliness is emphasized when disassembling internal components to prevent dirt contamination.
This document provides instructions for removing and installing an engine on a 432E Backhoe Loader. It outlines 50 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses and hoses, and removing mounting hardware. Tools required are listed. To install the engine, the 50 removal steps are reversed, taking care when connecting wiring harnesses and positioning mounting bolts. Proper lifting equipment is needed due to the engine weighing approximately 454 kg.
The document provides instructions for removing an engine oil cooler from a 432D BACKHOE LOADER, which includes draining fluids, removing housing bolts and seals, and removing the oil cooler. It then provides instructions for installing a new oil cooler, which includes cleaning surfaces, installing new seals and bolts, and refilling fluids. Separate instructions are given for removing and installing an engine oil relief valve.
This document provides instructions for installing an engine in a 430F2 backhoe loader. It describes lifting the engine into place using load leveling beams, aligning and bolting the bell housing and flywheel, installing engine mounts and accessories like the starter motor, alternator, and air conditioning compressor, and filling fluids like coolant and oil. The final steps include installing panels and covers to complete the engine installation.
This service repair manual provides instructions for removing and installing exhaust manifolds and inlet manifolds on Caterpillar 3054 engines. It describes removing manifold bolts and nuts, removing gaskets, cleaning parts, installing new gaskets, reinstalling manifolds and tightening bolts or nuts to the specified torque for both type 1, type 2 and 7BJ engines. The document is from the Caterpillar Service Information System and provides detailed step-by-step instructions and illustrations for mechanics performing maintenance on Caterpillar equipment.
The document provides instructions for removing and installing a crankshaft rear seal and flywheel housing on a Caterpillar 430F2 backhoe loader. It describes using various tools to remove torx screws and seals, cleaning parts, installing a new seal with a plastic sleeve, and tightening bolts to specified torques. The instructions are part of a service manual for maintenance and repair of engine components.
This document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 430F2 backhoe loader with a C4.4 engine. It outlines the necessary tools and describes a 7 step process for removal and a 9 step process for installation. Safety notices are included to keep parts clean and prevent damage during the procedure.
This document provides instructions for removing and installing a hydraulic tank on a 430F backhoe loader. The removal procedure involves disconnecting hoses from the tank, removing clamps, and taking out bolts to detach the tank assembly. Components like a strainer and gauge are then removed from the tank. Reinstallation involves reversing these steps and reattaching all hoses, clamps, and bolts.
This document provides instructions for removing and installing the front gear group of a C4.4 engine. The procedure involves:
1. Locking the crankshaft and camshaft in position using timing pins.
2. Marking the gears to ensure proper reinstallation.
3. Removing the fuel pump, camshaft, and idler gears.
4. Cleaning and inspecting the gear components.
5. Reinstalling the gears, ensuring proper timing and backlash measurements.
The document provides instructions for disassembling and assembling the direct drive transmission of a 430E Backhoe Loader. It lists required tools and gives step-by-step instructions to remove components such as gears, bearings, seals, and shafts. It describes using various tools to press, pull, or remove parts. Reassembly is to be done in major components and with a focus on cleanliness.
The document provides instructions for removing a hydraulic tank from a 428E BACKHOE LOADER. It involves draining the hydraulic oil, removing various panels and covers, and disconnecting hoses and harnesses. Key steps include removing bolts and panels to access the tank, then disconnecting multiple hose assemblies and a harness connecting to the tank before it can be lifted out. The process requires draining fluid first and removes parts in a specific sequence for access.
This document provides instructions for removing and installing various components of a Caterpillar 3054C diesel engine, including:
- Lifter group removal and installation
- Camshaft removal and installation
- Camshaft bearing removal and installation
- Engine oil pan removal and installation
The summaries include detailed step-by-step instructions, required tools, safety notices, and references to other relevant sections for complete disassembly and reassembly. Precautions are outlined to prevent contamination and damage to parts.
This document provides instructions for removing and installing fuel injection nozzles and the fuel injection pump on a Caterpillar 3054 engine. It describes in detail:
- Removing fuel injection lines before removing nozzles or pump
- Using timing pins to ensure proper alignment when removing the pump
- Cleaning parts and applying anti-seize compound when installing nozzles
- Torque specifications for reinstalling nozzles and pump components
The document is from a service repair manual and contains detailed step-by-step instructions and illustrations for working on specific engine systems.
The document provides instructions for removing and disassembling the transmission of a 428D backhoe loader. It describes 19 steps to disassemble the transmission into its major components, including removing valve groups, filters, seals, shafts, and other parts. Special tools are required and care must be taken to contain fluids. The transmission weighs 172 kg and its components require lifting devices and stands for removal and handling.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for disassembling the transmission of a 428D backhoe loader. It describes removing the transmission from the machine and then disassembling the major transmission components. These include removing the output shafts on the front and rear of the transmission, along with the input shaft. Bearings and gears are then removed from each shaft. The transmission case is also disassembled by removing bearing cups. Tools required for disassembly are listed.
The document provides instructions for disassembling and assembling the steering metering pump of a 428D Backhoe Loader. It describes 18 steps to disassemble the pump by removing components like end caps, seals, springs, and fittings. It also lists 3 steps for assembling the pump, including installing fittings, seals, and bushings. Personal safety precautions are provided regarding hydraulic pressure and fluid containment.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles or pumps
- Using tools like pins and pullers to remove nozzles and pumps while ensuring proper timing
- Cleaning parts and applying anti-seize compound when installing nozzles
- Tightening nozzles and bolts on pumps to specified torques
- Ensuring number 1 cylinder is at top center when removing components
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1NR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406238
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00546794
Typical Example. Different lifting device shown than what is called out in the Table.
Illustration 2 g00546793
1. Install Tool (A) and a suitable lifting device on flywheel (1) .
2. Remove bolts (3) and bearing housing (4) .
3. Remove six bolts (2) and the washers from the flywheel.
Note: The 3054 and 3056 marine engines used several bolt patterns to attach the flywheel to
the crankshaft. There are drilled holes that are not used in the crankshaft and in the
flywheel.
4. Use the suitable lifting device in order to remove flywheel (1) . The weight of flywheel (1)
and the flywheel ring gear is 53 kg (120 lb).
5. If removal of the flywheel ring gear is necessary, place an index mark on the chamfer of the
flywheel ring gear for the installation process.
Illustration 3 g00546795
2/3
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 6. Use a hammer and a punch in order to remove flywheel ring gear (5) from flywheel (1) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 16 15:14:10 UTC+0800 2019
3/3
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1NR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406239
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
Always wear protective gloves when handling parts that have been
heated.
1/2
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00803517
Typical Example. Different Lifting device shown than what is called out in the table.
1. If flywheel ring gear (5) was removed, heat flywheel ring gear (5) to a temperature of 250 °
C (480 °F).
Note: Do not use a torch to heat the flywheel ring gear.
2. Install flywheel ring gear (5) on flywheel (1) .
Note: Ensure that the chamfer of the flywheel ring gear is in the correct position on the
flywheel.
3. Install Tool (A) and a suitable lifting device on flywheel (1) and position flywheel (1) in the
flywheel housing. The weight of flywheel (1) and flywheel ring gear (5) is 53 kg (120 lb).
Illustration 2 g00546793
4. Install six bolts (2) and the washers that hold flywheel (1) in position. Tighten the bolts to a
torque of 105 N·m (77 lb ft).
5. Put bearing housing (4) in position on the flywheel. Install four bolts (3) that fasten bearing
housing (4) to the flywheel.
6. Refer to the Specifications Module, "Flywheel" topic for information on inspecting the
flywheel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 16 15:15:06 UTC+0800 2019
2/2
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1NR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741403
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Engines with 14 Bolt Housing Assembly
Illustration 1 g00632744
The flywheel housing has been removed for photographic purposes only.
1. Remove bolts (1) from housing (3).
2. Remove socket head bolts (2) from housing (3).
3. Remove the crankshaft rear seal, the gasket, and housing (3) from the dowels in the cylinder
block.
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
Illustration 2 g00830867
2/3
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 1. Remove the bolts in reverse order of the numbered sequence. Refer to Illustration 2.
2. Remove the one-piece housing assembly from the cylinder block.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 16 15:16:02 UTC+0800 2019
3/3
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1NR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01605362
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6205 Rear Seal Installer 1
1P-0510 Driver Group 1
B FT-2806 Alignment Tool 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engines with 14 Bolt Housing Assembly
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Clean the areas of the parts that will contact each other.
1/4
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00541839
3. Use Tool (A) and a suitable press to install the crankshaft rear seal into the housing. Make
sure that you install the seal to the correct depth in the housing. Refer to Specifications,
"Crankshaft Seals" for additional information.
4. Lubricate the crankshaft flange and the lip of the crankshaft rear seal with clean engine oil.
5. Install Tool (A) onto the crankshaft flange.
6. Put the new gasket for the housing in position on the dowels in the cylinder block.
Illustration 2 g00606404
7. Carefully place housing (3) and crankshaft rear seal (4) over Tool (A) .
8. Position housing (3) on the dowels in the cylinder block.
9. Remove Tool (A) .
2/4
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00606340
The flywheel housing has been removed for photographic purposes only.
10. Install bolts (1) and socket head bolts (2) that fasten housing (3) to the cylinder block.
11. Tighten all of the bolts to a torque of 22 N·m (16 lb ft).
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
1. Ensure that all parts and surfaces of the engine block are clean and free from oil, grease, and
dirt.
Illustration 4 g00831176
3/4
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the
crankshaft flange before installation.
2. Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the
cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the
plastic sleeve after the housing assembly is installed.
3. Place Tool (B) over housing assembly (3). This will center the housing assembly onto the
crankshaft flange.
Illustration 5 g00830867
4. Install the bolts with Tool (B) in position in order to fasten housing assembly (3) to the
cylinder block. Tighten bolts 1 and 2 to a torque of 22 N·m (16 lb ft).
5. Remove Tool (B). Tighten the remaining bolts in sequence to a torque of 22 N·m (16 lb ft).
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 16 15:16:58 UTC+0800 2019
4/4
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1NR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741450
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
16. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Support the engine with blocks or with a suitable lifting device on a flat level surface.
Illustration 1 g00541891
Typical example
2. Remove mounting bolts (1) from the top of flywheel housing (2).
Illustration 2 g00541892
Typical example
3. Attach Tooling (A) and a suitable lifting device to flywheel housing (2).
4. Remove mounting bolts (3) that attach the flywheel housing to the cylinder block.
2/4
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 5. Remove flywheel housing (2). If necessary, hit flywheel housing (2) with a soft faced
hammer in order to separate flywheel housing (2) from the cylinder block. The weight of
flywheel housing (2) is approximately 32 kg (70 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the rear face of the cylinder block and the mating surface of the flywheel housing.
Inspect the felt seal on the rear flange of the engine oil pan. Replace the felt seal, if
necessary. Inspect the dowels in the cylinder block that align the flywheel housing. Replace
the dowels, if necessary.
Illustration 3 g00541892
2. Use Tooling (A) and a suitable lifting device to position flywheel housing (2) on the dowels
that are on the cylinder block. The weight of flywheel housing (2) is approximately 32 kg
(70 lb).
3. Install mounting bolts (3).
3/4
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 4 g00541891
Typical example
4. Install mounting bolts (1) that attach flywheel housing (2) to the cylinder block.
Tighten the bolts for an aluminum flywheel housing to a torque of 70 N·m (52 lb ft).
Tighten the cast iron flywheel housing bolts to the following torque:
M10 "8.8" ... 44 N·m (33 lb ft)
M10 "10.9" ... 63 N·m (46 lb ft)
M12 "8.8" ... 75 N·m (55 lb ft)
M12 "10.9" ... 115 N·m (85 lb ft)
5. Remove Tooling (A) from the flywheel housing.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 16 15:17:53 UTC+0800 2019
4/4
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1NR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01461242
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
A. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Illustration 1 g00553762
Typical example
1. Remove three bolts (2) that hold thrust block (3) in position.
2. Remove thrust block (3) from the end of the crankshaft. The thrust block holds the
crankshaft pulley in position on the end of the crankshaft.
3. Remove crankshaft pulley (1) from the engine.
1/2
426C Backhoe Loader Center Pivot, Parallel Lift 1NR01050-UP (MACHINE) POWE...
2019/12/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...