This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles or pumps
- Using tools like pins and pullers to remove nozzles and pumps while ensuring proper timing
- Cleaning parts and applying anti-seize compound when installing nozzles
- Tightening nozzles and bolts on pumps to specified torques
- Ensuring number 1 cylinder is at top center when removing components
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. The removal procedure for fuel injection nozzles includes removing fuel injection lines, loosening a threaded nut, and removing the nozzle and seat washer from the cylinder block. The installation procedure describes cleaning parts, installing a new seat washer, positioning the nozzle, and tightening the nut. The document also provides multiple procedures for removing and installing fuel injection pumps depending on the engine type, including ensuring proper timing and using special tools.
This document provides instructions for removing fuel injection nozzles from a 428C BACKHOE LOADER model. It describes:
- Removing the fuel injection lines first
- Loosening the threaded nut on the nozzle and removing it from the cylinder block along with the seat washer
- Keeping all parts clean to prevent contamination
It also cautions to contain fluids and dispose of them properly according to regulations.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. The removal procedure for fuel injection nozzles includes removing fuel injection lines, loosening a threaded nut, and removing the nozzle and seat washer from the cylinder block. The installation procedure describes cleaning parts, installing a new seat washer, positioning the nozzle, and tightening the nut. The document also provides multiple procedures for removing and installing fuel injection pumps depending on the engine type, including ensuring proper timing and using special tools.
This document provides instructions for removing and installing fuel injection nozzles and inlet and exhaust valves on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles
- Loosening nuts and removing nozzles and seat washers from the cylinder block
- Cleaning parts and installing nozzles with new seat washers, applying anti-seize compound, and tightening nuts to the specified torque
- Installing fuel injection lines after installing nozzles
- Index marking valves before removal and using a compressor tool to remove springs and valve keepers
- Inspecting valve depths and installing valves with new springs and keepers
This document provides instructions for removing and installing fuel injection nozzles and inlet and exhaust valve springs on a Caterpillar 3054 engine. The fuel injection nozzle removal procedure involves removing fuel lines, loosening a threaded nut, and removing the nozzle and seat washer. Installation involves cleaning parts, installing a new seat washer, applying anti-seize compound, and tightening the nut. The valve spring procedure requires using a special tool to compress springs, removing keepers and retainers, and ensuring the piston is at top-dead-center during removal and installation. Proper cleaning and torque specifications are emphasized throughout.
This document provides instructions for removing and installing fuel injection nozzles and inlet and exhaust valve springs on a Caterpillar 3054 engine. The fuel injection nozzle removal procedure involves removing fuel lines, loosening a threaded nut, and removing the nozzle and seat washer. Installation involves cleaning parts, installing a new seat washer, applying anti-seize compound, and tightening the nut. The valve spring procedure requires using a special tool to compress springs, removing keepers and retainers, and ensuring the piston is at top-dead-center during removal and installation. Proper cleaning and torque specifications are emphasized throughout.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, cleaning parts, and installing new seals and following tightening specifications. Special attention is given to ensuring proper timing is maintained when removing and installing components.
This document provides instructions for removing and installing fuel injection nozzles on a 428C BACKHOE LOADER. It describes removing the fuel injection lines, loosening the threaded nut on the nozzle, and removing the nozzle and seat washer. For installation, it instructs to clean parts, install a new seat washer, apply anti-seize compound, insert the nozzle ensuring proper alignment, and tighten the nut to the specified torque. Additional sections provide similar instructions for other engine models.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. The removal procedure for fuel injection nozzles includes removing fuel injection lines, loosening a threaded nut, and removing the nozzle and seat washer from the cylinder block. The installation procedure describes cleaning parts, installing a new seat washer, positioning the nozzle, and tightening the nut. The document also provides multiple procedures for removing and installing fuel injection pumps depending on the engine type, including ensuring proper timing and using special tools.
This document provides instructions for removing fuel injection nozzles from a 428C BACKHOE LOADER model. It describes:
- Removing the fuel injection lines first
- Loosening the threaded nut on the nozzle and removing it from the cylinder block along with the seat washer
- Keeping all parts clean to prevent contamination
It also cautions to contain fluids and dispose of them properly according to regulations.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. The removal procedure for fuel injection nozzles includes removing fuel injection lines, loosening a threaded nut, and removing the nozzle and seat washer from the cylinder block. The installation procedure describes cleaning parts, installing a new seat washer, positioning the nozzle, and tightening the nut. The document also provides multiple procedures for removing and installing fuel injection pumps depending on the engine type, including ensuring proper timing and using special tools.
This document provides instructions for removing and installing fuel injection nozzles and inlet and exhaust valves on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles
- Loosening nuts and removing nozzles and seat washers from the cylinder block
- Cleaning parts and installing nozzles with new seat washers, applying anti-seize compound, and tightening nuts to the specified torque
- Installing fuel injection lines after installing nozzles
- Index marking valves before removal and using a compressor tool to remove springs and valve keepers
- Inspecting valve depths and installing valves with new springs and keepers
This document provides instructions for removing and installing fuel injection nozzles and inlet and exhaust valve springs on a Caterpillar 3054 engine. The fuel injection nozzle removal procedure involves removing fuel lines, loosening a threaded nut, and removing the nozzle and seat washer. Installation involves cleaning parts, installing a new seat washer, applying anti-seize compound, and tightening the nut. The valve spring procedure requires using a special tool to compress springs, removing keepers and retainers, and ensuring the piston is at top-dead-center during removal and installation. Proper cleaning and torque specifications are emphasized throughout.
This document provides instructions for removing and installing fuel injection nozzles and inlet and exhaust valve springs on a Caterpillar 3054 engine. The fuel injection nozzle removal procedure involves removing fuel lines, loosening a threaded nut, and removing the nozzle and seat washer. Installation involves cleaning parts, installing a new seat washer, applying anti-seize compound, and tightening the nut. The valve spring procedure requires using a special tool to compress springs, removing keepers and retainers, and ensuring the piston is at top-dead-center during removal and installation. Proper cleaning and torque specifications are emphasized throughout.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, cleaning parts, and installing new seals and following tightening specifications. Special attention is given to ensuring proper timing is maintained when removing and installing components.
This document provides instructions for removing and installing fuel injection nozzles on a 428C BACKHOE LOADER. It describes removing the fuel injection lines, loosening the threaded nut on the nozzle, and removing the nozzle and seat washer. For installation, it instructs to clean parts, install a new seat washer, apply anti-seize compound, insert the nozzle ensuring proper alignment, and tighten the nut to the specified torque. Additional sections provide similar instructions for other engine models.
This document provides instructions for removing and installing fuel injection nozzles on a 428C BACKHOE LOADER. It describes removing the fuel injection lines, loosening the threaded nut on the nozzle, and removing the nozzle and seat washer. For installation, it instructs to clean parts, install a new seat washer, apply anti-seize compound, insert the nozzle ensuring proper alignment, and tighten the nut to the specified torque. Additional sections provide similar instructions for other engine models.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, cleaning parts, and installing new seals and following tightening specifications. Special attention is given to ensuring proper timing is maintained throughout the process.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, cleaning parts, and installing new seals and following tightening specifications. Special attention is given to ensuring proper timing is maintained when removing and installing components.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, cleaning parts, and installing new seals and following tightening specifications. Special attention is given to ensuring proper timing is maintained when removing and installing components.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
This document provides instructions for removing and installing fuel injection nozzles on a 428C BACKHOE LOADER. It describes removing the fuel injection lines, loosening the threaded nut on the nozzle, removing the nozzle and seat washer from the cylinder block. For installation, it describes cleaning parts, installing a new seat washer, applying anti-seize compound, inserting the nozzle into position and tightening the nut to the specified torque. Additional sections provide similar instructions for other engine models.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
Caterpillar cat 428 c backhoe loader (prefix 2cr) service repair manual (2cr0...fjjksekksemm
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. The instructions are separated into sections for different engine types. To remove fuel injection nozzles, the fuel lines must first be removed. Then the nut on the nozzle is loosened and the nozzle is removed along with the seat washer. To install nozzles, the threads are cleaned and a new seat washer is installed before tightening the nut with anti-seize compound. To remove fuel injection pumps, the water pump and fuel lines must first be removed. Then various bolts and nuts are removed to detach the pump from the engine.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
This document provides assembly instructions for the transmission of a 434E BACKHOE LOADER model. It lists the required tools and notes on cleanliness and lubrication. It then provides step-by-step instructions with illustrations for assembling the various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft (rear). Proper compression of springs and installation of seals, bearings, gears and other parts is described.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
This document provides instructions for disassembling and removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support tubes to lift the front and rear of the machine, draining the transmission fluid.
2) Removing mounting bolts, brackets and hoses to separate the transmission from the engine and rear axle housing.
3) Using overhead lift equipment to remove the transmission once it is fully separated from the machine.
The document provides instructions for disassembling and removing various components of a 432F2 backhoe loader, including the axle housing, brake assembly, differential and bevel gear, solenoid valve, and releasing system pressure. Key steps include using various tools to remove bearings, gears, pins, seals, and other parts. Precautions are outlined for releasing spring pressure safely.
This document provides disassembly instructions for the transmission of a 432E Backhoe Loader. It lists required tools and outlines 14 steps to fully disassemble the transmission. These include removing various gears, shafts, seals, bearings and other components from the front output shaft, rear output shaft, countershaft, idler shaft, and input shaft. Special care and tools are noted for removing springs and releasing pressurized components. The goal is to break down the transmission into its core individual parts for maintenance or replacement.
The document provides instructions for removing and disassembling the transmission of a 432D backhoe loader. It lists the required tools and gives step-by-step instructions to drain the transmission oil, remove mounting bolts, disconnect electrical connectors, and use lifting tools to safely remove the transmission. Cleanliness is emphasized when disassembling internal components to prevent dirt contamination.
This document provides instructions for removing and installing an engine on a 432E Backhoe Loader. It outlines 50 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses and hoses, and removing mounting hardware. Tools required are listed. To install the engine, the 50 removal steps are reversed, taking care when connecting wiring harnesses and positioning mounting bolts. Proper lifting equipment is needed due to the engine weighing approximately 454 kg.
The document provides instructions for removing an engine oil cooler from a 432D BACKHOE LOADER, which includes draining fluids, removing housing bolts and seals, and removing the oil cooler. It then provides instructions for installing a new oil cooler, which includes cleaning surfaces, installing new seals and bolts, and refilling fluids. Separate instructions are given for removing and installing an engine oil relief valve.
More Related Content
Similar to Caterpillar Cat 428C BACKHOE LOADER (Prefix 8RN) Service Repair Manual (8RN04089-04989).pdf
This document provides instructions for removing and installing fuel injection nozzles on a 428C BACKHOE LOADER. It describes removing the fuel injection lines, loosening the threaded nut on the nozzle, and removing the nozzle and seat washer. For installation, it instructs to clean parts, install a new seat washer, apply anti-seize compound, insert the nozzle ensuring proper alignment, and tighten the nut to the specified torque. Additional sections provide similar instructions for other engine models.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, cleaning parts, and installing new seals and following tightening specifications. Special attention is given to ensuring proper timing is maintained throughout the process.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, cleaning parts, and installing new seals and following tightening specifications. Special attention is given to ensuring proper timing is maintained when removing and installing components.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, cleaning parts, and installing new seals and following tightening specifications. Special attention is given to ensuring proper timing is maintained when removing and installing components.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
This document provides instructions for removing and installing fuel injection nozzles on a 428C BACKHOE LOADER. It describes removing the fuel injection lines, loosening the threaded nut on the nozzle, removing the nozzle and seat washer from the cylinder block. For installation, it describes cleaning parts, installing a new seat washer, applying anti-seize compound, inserting the nozzle into position and tightening the nut to the specified torque. Additional sections provide similar instructions for other engine models.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
Caterpillar cat 428 c backhoe loader (prefix 2cr) service repair manual (2cr0...fjjksekksemm
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. The instructions are separated into sections for different engine types. To remove fuel injection nozzles, the fuel lines must first be removed. Then the nut on the nozzle is loosened and the nozzle is removed along with the seat washer. To install nozzles, the threads are cleaned and a new seat washer is installed before tightening the nut with anti-seize compound. To remove fuel injection pumps, the water pump and fuel lines must first be removed. Then various bolts and nuts are removed to detach the pump from the engine.
Similar to Caterpillar Cat 428C BACKHOE LOADER (Prefix 8RN) Service Repair Manual (8RN04089-04989).pdf (12)
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
This document provides assembly instructions for the transmission of a 434E BACKHOE LOADER model. It lists the required tools and notes on cleanliness and lubrication. It then provides step-by-step instructions with illustrations for assembling the various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft (rear). Proper compression of springs and installation of seals, bearings, gears and other parts is described.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
This document provides instructions for disassembling and removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support tubes to lift the front and rear of the machine, draining the transmission fluid.
2) Removing mounting bolts, brackets and hoses to separate the transmission from the engine and rear axle housing.
3) Using overhead lift equipment to remove the transmission once it is fully separated from the machine.
The document provides instructions for disassembling and removing various components of a 432F2 backhoe loader, including the axle housing, brake assembly, differential and bevel gear, solenoid valve, and releasing system pressure. Key steps include using various tools to remove bearings, gears, pins, seals, and other parts. Precautions are outlined for releasing spring pressure safely.
This document provides disassembly instructions for the transmission of a 432E Backhoe Loader. It lists required tools and outlines 14 steps to fully disassemble the transmission. These include removing various gears, shafts, seals, bearings and other components from the front output shaft, rear output shaft, countershaft, idler shaft, and input shaft. Special care and tools are noted for removing springs and releasing pressurized components. The goal is to break down the transmission into its core individual parts for maintenance or replacement.
The document provides instructions for removing and disassembling the transmission of a 432D backhoe loader. It lists the required tools and gives step-by-step instructions to drain the transmission oil, remove mounting bolts, disconnect electrical connectors, and use lifting tools to safely remove the transmission. Cleanliness is emphasized when disassembling internal components to prevent dirt contamination.
This document provides instructions for removing and installing an engine on a 432E Backhoe Loader. It outlines 50 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses and hoses, and removing mounting hardware. Tools required are listed. To install the engine, the 50 removal steps are reversed, taking care when connecting wiring harnesses and positioning mounting bolts. Proper lifting equipment is needed due to the engine weighing approximately 454 kg.
The document provides instructions for removing an engine oil cooler from a 432D BACKHOE LOADER, which includes draining fluids, removing housing bolts and seals, and removing the oil cooler. It then provides instructions for installing a new oil cooler, which includes cleaning surfaces, installing new seals and bolts, and refilling fluids. Separate instructions are given for removing and installing an engine oil relief valve.
This document provides instructions for installing an engine in a 430F2 backhoe loader. It describes lifting the engine into place using load leveling beams, aligning and bolting the bell housing and flywheel, installing engine mounts and accessories like the starter motor, alternator, and air conditioning compressor, and filling fluids like coolant and oil. The final steps include installing panels and covers to complete the engine installation.
This service repair manual provides instructions for removing and installing exhaust manifolds and inlet manifolds on Caterpillar 3054 engines. It describes removing manifold bolts and nuts, removing gaskets, cleaning parts, installing new gaskets, reinstalling manifolds and tightening bolts or nuts to the specified torque for both type 1, type 2 and 7BJ engines. The document is from the Caterpillar Service Information System and provides detailed step-by-step instructions and illustrations for mechanics performing maintenance on Caterpillar equipment.
The document provides instructions for removing and installing a crankshaft rear seal and flywheel housing on a Caterpillar 430F2 backhoe loader. It describes using various tools to remove torx screws and seals, cleaning parts, installing a new seal with a plastic sleeve, and tightening bolts to specified torques. The instructions are part of a service manual for maintenance and repair of engine components.
This document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 430F2 backhoe loader with a C4.4 engine. It outlines the necessary tools and describes a 7 step process for removal and a 9 step process for installation. Safety notices are included to keep parts clean and prevent damage during the procedure.
This document provides instructions for removing and installing a hydraulic tank on a 430F backhoe loader. The removal procedure involves disconnecting hoses from the tank, removing clamps, and taking out bolts to detach the tank assembly. Components like a strainer and gauge are then removed from the tank. Reinstallation involves reversing these steps and reattaching all hoses, clamps, and bolts.
This document provides instructions for removing and installing the front gear group of a C4.4 engine. The procedure involves:
1. Locking the crankshaft and camshaft in position using timing pins.
2. Marking the gears to ensure proper reinstallation.
3. Removing the fuel pump, camshaft, and idler gears.
4. Cleaning and inspecting the gear components.
5. Reinstalling the gears, ensuring proper timing and backlash measurements.
The document provides instructions for disassembling and assembling the direct drive transmission of a 430E Backhoe Loader. It lists required tools and gives step-by-step instructions to remove components such as gears, bearings, seals, and shafts. It describes using various tools to press, pull, or remove parts. Reassembly is to be done in major components and with a focus on cleanliness.
The document provides instructions for removing a hydraulic tank from a 428E BACKHOE LOADER. It involves draining the hydraulic oil, removing various panels and covers, and disconnecting hoses and harnesses. Key steps include removing bolts and panels to access the tank, then disconnecting multiple hose assemblies and a harness connecting to the tank before it can be lifted out. The process requires draining fluid first and removes parts in a specific sequence for access.
This document provides instructions for removing and installing various components of a Caterpillar 3054C diesel engine, including:
- Lifter group removal and installation
- Camshaft removal and installation
- Camshaft bearing removal and installation
- Engine oil pan removal and installation
The summaries include detailed step-by-step instructions, required tools, safety notices, and references to other relevant sections for complete disassembly and reassembly. Precautions are outlined to prevent contamination and damage to parts.
This document provides instructions for removing and installing fuel injection nozzles and the fuel injection pump on a Caterpillar 3054 engine. It describes in detail:
- Removing fuel injection lines before removing nozzles or pump
- Using timing pins to ensure proper alignment when removing the pump
- Cleaning parts and applying anti-seize compound when installing nozzles
- Torque specifications for reinstalling nozzles and pump components
The document is from a service repair manual and contains detailed step-by-step instructions and illustrations for working on specific engine systems.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02108297
Fuel Injection Nozzles - Remove
SMCS - 1254-011
Removal Procedure
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00902563
1. Loosen threaded nut (1) on the fuel injection nozzle.
Illustration 2 g00902564
2. Remove fuel injection nozzle (2) from the cylinder block.
3. Remove seat washer (3).
Note: If the original seat washer is not removed, the projection of the fuel injection nozzle
will be incorrect when a new seat washer is installed.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 13 13:36:38 UTC+0800 2019
2/2
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01760208
Fuel Injection Nozzles - Install
SMCS - 1254-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00903765
1. Thoroughly clean the threads on threaded nut (1) and the cylinder head.
2. Install a new seat washer (3) into the recess in the cylinder head.
1/3
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Note: If the original seat washer is reused, the projection of the fuel injection nozzle will be
incorrect.
3. Put a 2.0 mm (0.08 inch) bead of 4C-5591 Anti-Seize Compound on the first two threads of
threaded nut (1).
Illustration 2 g00903762
Illustration 3 g00903704
4. Put fuel injection nozzle (2) into position in the cylinder head. Make sure that the detent ball
in the fuel injection nozzle (2) is aligned correctly with ball Detent (X) in the cylinder head.
Illustration 4 g00902563
2/3
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 5. Carefully tighten threaded nut (1) to a torque of 30 N·m (22 lb ft). Remove any excess Anti-
Seize Compound from fuel injection nozzle.
Note: Do not rotate the fuel injection nozzle after installation. The seal which is made by
the anti-seize compound may break. A broken seal may allow leakage past the seat of the
fuel injection nozzle.
End By:
a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 13 13:37:35 UTC+0800 2019
3/3
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01080672
Fuel Injection Nozzles - Install - Type 1 Engines and 9RM
Engines
SMCS - 1254-012
Installation Procedure
Note: For a complete description of Type 1 and Type 2 Engines, refer to the Disassembly and
Assembly, "Engine Design" topic.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00545200
1. Install dust seal (5) and spacer (4) .
2. Install the seat washer on the end of fuel injection nozzle (3) .
3. Install fuel injection nozzle (3) into the cylinder head.
Illustration 2 g00545199
4. Install clamp (2) and bolts (1). Tighten bolts (1) to a torque of 12 N·m (9 lb ft).
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 13 13:38:32 UTC+0800 2019
2/2
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02105278
Fuel Injection Pump - Remove - Type 2 Engines and 7BJ
Engines
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
150-3992 Timing Pin (1)
1
150-3993 Timing Pin (2)
1
B
171-1085
or
173-9774
Tamper Resistant Tool Gp 1
( 1 )
Tool (A) is required in order to remove Bosch fuel injection pumps.
( 2 )
Tool (A) is required in order to remove Delphi (Lucas) and Stanadyne fuel injection pumps.
Start By:
A. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
B. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Ensure that the No. 1 cylinder is at the top center position on the compression stroke. Refer
to the Testing and Adjusting, "Fuel System" topic for additional information.
Illustration 1 g00808245
2. Loosen locking screw (2) (if equipped) until locking spacer (1) moves freely. Move locking
spacer (1) into position (B). Tighten locking screw (2) to a torque of 10 N·m (7 lb ft).
2/4
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 2 g00808370
Typical example
Note: Do not remove hub nut (4) from the shaft of the fuel injection pump. The hub of the
fuel injection pump is installed in the correct position from the factory in order to ensure
proper timing. If hub nut (4) is removed and the hub is removed, the hub will need to be
accurately installed on the shaft of the fuel injection pump by the use of special equipment.
Refer to your Caterpillar Dealer for more information.
Note: Do not release Torx screws (5) (if equipped). If the Torx screws are released and the
timing plate is moved, the timing position that is set at the factory will be lost. If the Torx
screws are released, the No. 1 cylinder must be set to the top center position on the
compression stroke before the Torx screws are tightened.
3. Slowly rotate the crankshaft until hole (6) in the timing gear and hole (7) in the hub are in
alignment with hole (8) in the fuel injection pump body.
Note: The location of Tool (A) for Bosch fuel injection pumps will be located toward the
top of the fuel injection pump. The location of Tool (A) for Delphi (Lucas) and Stanadyne
fuel injection pumps will be located toward the bottom of the fuel injection pump.
4. Install Tool (A) through hole (6) in the timing gear and hole (7) in the hub. Push Tool (A)
into position in hole (8) in the fuel injection pump body. If Tool (A) can be fully seated, the
fuel injection pump timing is correct. No resistance should be felt when the timing pin is
inserted into hole (8) of the fuel injection pump body.
3/4
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Note: Some fuel injection pumps are installed with tamper proof bolts. Tool (B) may be
necessary in order to remove the tamper proof bolts.
5. Remove four bolts (3) that fasten the fuel injection pump gear to the fuel injection pump.
Timing gear (9) should be free from the fuel injection pump shaft.
Illustration 3 g00808376
Typical example
6. Remove three flange nuts (10) and fuel injection pump (11) from the engine.
Illustration 4 g01059878
Typical example
7. Remove O-ring seal (12) from fuel injection pump (11) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 13 13:39:29 UTC+0800 2019
4/4
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01083652
Fuel Injection Pump - Remove - Type 1 Engines and 9RM
Engines
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 173-9774 Bolt Remover (1)
1
B 9U-6198 Crankshaft Turning Tool 1
C
8S-2264 Puller Group 1
8S-4712 Bolt 2
( 1 )
The bolt remover is required in order to remove the tamper proof bolts on the access cover for the fuel injection
pump.
Start By:
A. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
B. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Note: For a complete description of Type 1 and Type 2 engines, refer to the Disassembly and
Assembly, "Engine Design" topic.
NOTICE
Keep all parts clean from contaminants.
1/4
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00545256
1. Remove four bolts (1) .
Note: Some engines may have four tamper proof bolts (1). Use Tool (A) in order to remove
the tamper proof bolts bolts.
2. Remove cover (2) .
2/4
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g00545258
3. Remove nut (3) and the lockwasher.
Illustration 3 g00571370
4. Use Tool (B) to rotate the crankshaft until keyway (X) is at 30 degrees from the vertical
centerline.
Illustration 4 g00571373
3/4
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 5. Install Tool (C) .
6. Disengage the gear from the fuel injection pump.
Illustration 5 g00545262
7. Disconnect hose (7) from the fuel injection pump.
8. Remove three nuts (6) that hold fuel injection pump (5) in position.
9. Remove fuel injection pump (5) and the gasket.
Note: Ensure that you do not lose the key when the fuel injection pump is removed. Also
notice the position of marks (4) in order to ensure proper alignment of fuel injection pump
(5) during installation.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 13 13:40:25 UTC+0800 2019
4/4
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02046409
Fuel Injection Pump - Install - Type 2 Engines and 7BJ
Engines
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
150-3992 Timing Pin (1)
1
150-3993 Timing Pin (2)
1
B
171-1085
or
173-9774
Tamper Resistant Tool Gp 1
( 1 )
Tooling (A) is required in order to install Bosch fuel injection pumps.
( 2 )
Tooling (A) is required in order to install Dephi (Lucas) and Stanadyne fuel injection pumps.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Illustration 1 g01059878
Typical example
1. Check the condition of O-ring seal (13) on fuel injection pump (12). If the seal is worn or
damaged, replace the seal.
2. Lightly lubricate O-ring seal (13) with clean engine oil. Install O-ring seal (13) on fuel
injection pump (12) .
NOTICE
The No. 1 cylinder must be at the top center position on the
compression stroke before the fuel injection pump is installed. If the
crankshaft needs to be rotated, the fuel injection pump must be
mounted temporarily or the loose gear could cause damage to the front
housing.
Illustration 2 g00808376
Typical example
2/5
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 3. Put fuel injection pump (12) in position on the engine. Ensure that the timing gear is aligned
with the hub of fuel injection pump (12). Install three flange nuts (11) and tighten the flange
nuts to a torque of 28 N·m (21 lb ft).
Illustration 3 g00808370
Typical example
4. Position gear (9) on the shaft of the fuel injection pump.
Note: Some fuel injection pumps are installed with tamper proof bolts. Tooling (B) may be
necessary in order to install the tamper proof bolts.
5. Put the timing gear plate in position and install four bolts (3). Tighten the four bolts finger
tight.
Note: The fuel injection pump gear will only fit in one position. Install the gear with the
letters "C" and "M" facing away from the engine.
3/5
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 4 g00808245
Typical example
6. Loosen locking screw (2) (if equipped) until locking spacer (1) moves freely. Move locking
spacer (1) into position (A). Tighten locking screw (2) to a torque of 10 N·m (7 lb ft).
Note: The location of Tooling (A) for Bosch fuel injection pumps will be located toward the
top of the fuel injection pump. The location of Tooling (A) for Dephi (Lucas) and
Stanadyne fuel injection pumps will be located toward the bottom of the fuel injection
pump.
7. Install Tooling (A) through hole (6) in the timing gear and hole (7) in the hub. Push Tooling
(A) into position in hole (8) in the fuel injection pump body. If Tooling (A) can be fully
seated, the fuel injection pump timing is correct. No resistance should be felt when the
timing pin is inserted into hole (8) of the fuel injection pump body.
NOTICE
The fuel injection pump may be supplied with the fuel injection pump
shaft in the locked position. The drive shaft of the fuel injection pump
must not be rotated without the spacer in position under the locking
screw. Damage to the drive shaft of the fuel injection pump will result.
8. When the timing plate is installed, rotate gear (9) by hand in a counterclockwise direction in
order to remove the backlash between gear (9) and the idler gear. Do not rotate the
crankshaft or the fuel injection pump shaft. Tighten bolts (3) to a torque of 28 N·m (21 lb
ft).
9. Remove Tooling (A) from the fuel injection pump gear.
4/5
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. End By:
a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
b. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 13 13:41:22 UTC+0800 2019
5/5
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01083913
Fuel Injection Pump - Install - Type 1 Engines and 9RM
Engines
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 173-9774 Bolt Remover (1)
1
( 1 )
The bolt remover is required in order to install the tamper proof bolts on the access cover for the fuel injection
pump.
Note: For a complete description of Type 1 and Type 2 Engines, refer to the Disassembly and
Assembly, "Engine Design" topic.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the condition of the gasket for the fuel injection pump. Replace the gasket, if
necessary.
1/3
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g00545262
2. Install the gasket and fuel injection pump (5) .
Note: Align marks (4) that are on fuel injection pump (5) and the timing gear cover.
3. Install the key.
4. Install three nuts (6) that hold fuel injection pump (5) in position.
5. Connect hose (7) to fuel injection pump (5) .
6. Engage the gear with the fuel injection pump.
Illustration 2 g00545258
7. Install the lockwasher and nut (3) .
2/3
428C Backhoe Loader Center Pivot, Single Tilt 8RN04089-04989 (MACHINE) POW...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...