The document provides instructions for removing and installing a flywheel housing on a 422E Backhoe Loader. Key steps include:
1. Removing the flywheel, bolts, and lifting the housing off the engine block using lifting devices.
2. Inspecting the crankshaft rear seal for leaks before installing a cleaned housing with dowels and bolts, checking alignment with a dial indicator.
3. Reinstalling the flywheel to complete the process.
Caterpillar cat 416 e backhoe loader (prefix bwc) service repair manual (bwc0...fjjsekkksekmm
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment. For the crankshaft rear seal, it explains that the seal and housing are a single unit that must be replaced together if removed. Instructions are given to use torx sockets to remove and install the seal housing.
Caterpillar cat 416 e backhoe loader (prefix bwc) service repair manual (bwc0...fjsekkmsem
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment. For the crankshaft rear seal, it explains that the seal and housing are a single unit that must be replaced together if removed. Instructions are given to use torx sockets to remove and install the seal housing.
Caterpillar cat 416 e backhoe loader (prefix bwc) service repair manual (bwc0...fujsjefjkskzaemm
The document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 416E backhoe loader. It describes in steps how to remove the flywheel by taking out bolts, using guide bolts and lifting equipment due to the flywheel's weight. It then explains inspecting and removing the flywheel ring gear if needed. The installation process reverses these steps, including heating the new ring gear. Further sections detail removing and installing the crankshaft rear seal and flywheel housing, noting their weights and use of lifting devices.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful due to the flywheel's weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing the guide bolts and tightening the bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal. The seal is not serviceable and must be replaced.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful due to the flywheel's weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing the guide bolts and tightening the bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal. The seal is not serviceable and must be replaced.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using punches.
3. Cleaning and positioning the flywheel for installation, adding bolts finger tight before final tightening.
4. Removing housing bolts and lifting the housing off the engine block using a lifting device. Inspection of seals is required before reinstallation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using a hammer and punch.
3. Cleaning and inspecting components, then positioning the flywheel for installation with guide bolts before tightening bolts to the specified torque.
4. Removing bolts and lifting the flywheel housing off the engine cylinder block after removing the flywheel. Inspecting components and reversing steps
Caterpillar cat 416 e backhoe loader (prefix bwc) service repair manual (bwc0...fjjsekkksekmm
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment. For the crankshaft rear seal, it explains that the seal and housing are a single unit that must be replaced together if removed. Instructions are given to use torx sockets to remove and install the seal housing.
Caterpillar cat 416 e backhoe loader (prefix bwc) service repair manual (bwc0...fjsekkmsem
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment. For the crankshaft rear seal, it explains that the seal and housing are a single unit that must be replaced together if removed. Instructions are given to use torx sockets to remove and install the seal housing.
Caterpillar cat 416 e backhoe loader (prefix bwc) service repair manual (bwc0...fujsjefjkskzaemm
The document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 416E backhoe loader. It describes in steps how to remove the flywheel by taking out bolts, using guide bolts and lifting equipment due to the flywheel's weight. It then explains inspecting and removing the flywheel ring gear if needed. The installation process reverses these steps, including heating the new ring gear. Further sections detail removing and installing the crankshaft rear seal and flywheel housing, noting their weights and use of lifting devices.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful due to the flywheel's weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing the guide bolts and tightening the bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal. The seal is not serviceable and must be replaced.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful due to the flywheel's weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing the guide bolts and tightening the bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal. The seal is not serviceable and must be replaced.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using punches.
3. Cleaning and positioning the flywheel for installation, adding bolts finger tight before final tightening.
4. Removing housing bolts and lifting the housing off the engine block using a lifting device. Inspection of seals is required before reinstallation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using a hammer and punch.
3. Cleaning and inspecting components, then positioning the flywheel for installation with guide bolts before tightening bolts to the specified torque.
4. Removing bolts and lifting the flywheel housing off the engine cylinder block after removing the flywheel. Inspecting components and reversing steps
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using punches.
3. Cleaning and aligning the crankshaft flange before pressing the new crankshaft rear seal onto the flange using an alignment tool.
4. Removing bolts to lift the flywheel housing off the engine cylinder block using a lifting device. Inspection and installation steps are also
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment due to the flywheel's weight of approximately 155 pounds. For installing the flywheel, the instructions specify cleaning components, heating the ring gear, lifting the flywheel into place, and tightening bolts to the specified torque. Removing the crankshaft rear seal involves using a socket to remove screws, while installing requires aligning and pressing the new seal onto the crankshaft flange and torquing screws to the specified value.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it with guide bolts and lifting equipment, replacing bolts, and tightening them in sequence.
3) Removing the crankshaft rear seal by taking out torx screws and discarding the seal and housing assembly.
4) Installing the new crankshaft rear seal by aligning it on the crankshaft flange, installing torx
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment. It similarly describes removing the flywheel housing by taking out bolts and checking seals. Reinstallation involves cleaning, installing dowels or seals if needed, and torquing bolts with a lifting device and dial indicator used for alignment.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it with guide bolts and lifting equipment, replacing bolts and checking run out.
3) Removing the crankshaft rear seal by taking out torx screws and discarding the seal and housing assembly.
4) Installing the new crankshaft rear seal by aligning it on the crankshaft flange without lubrication, installing torx
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual (CAM0000...f8useudjkddmm2
This document provides instructions for removing and installing inlet and exhaust valve seats in a 322C FM excavator engine. It outlines the required tools and gives step-by-step procedures for removal and installation. Removal involves using a valve seat extractor tool to pull each seat from the cylinder head. Installation requires tapping new seats into place and ensuring they are flush with the head. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual (C3R0000...f8useudjkddmm2
1. The document provides instructions for removing and installing the unit injector hydraulic pump and turbocharger on a Caterpillar 3126B engine.
2. The unit injector hydraulic pump removal instructions include disconnecting lines and harness, removing mounting bolts, and inspecting seals. Installation is the reverse.
3. Turbocharger removal requires removing bolts from exhaust and oil lines. Disassembly separates housing components. Installation reconnects components and lines.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual (BPH0000...f8useudjkddmm2
This document provides instructions for removing and installing a governor from a 322C FM EXCAVATOR engine. It describes disconnecting linkages, removing mounting bolts and clips, and using special tools. Proper cleaning and lubrication of seals is emphasized. References are provided for additional information on governor inspection and fuel linkage components.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...f8useudjkddmm2
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 320D L excavator. The removal procedure involves using a link bracket and lifting device to remove the flywheel housing after removing bolts and washers. The installation procedure instructs to clean surfaces, apply retaining compound, and use the link bracket to reinstall the flywheel housing and check that the oil seal is correctly installed.
Caterpillar Cat 320D L Excavator (Prefix KLM) Service Repair Manual (KLM00001...f8useudjkddmm2
This document provides instructions for removing the crankshaft front seal from a Caterpillar C6.4 engine. The steps are:
1. Remove the crankshaft pulley using a combination puller tool.
2. Use a suitable chisel and hammer to remove the wear sleeve from the crankshaft pulley, if necessary.
3. Pull out the crankshaft front seal using the appropriate seal removal tool.
Caterpillar Cat 320D L Excavator (Prefix JFZ) Service Repair Manual (JFZ00001...f8useudjkddmm2
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix W8S) Service Repair ...f8useudjkddmm2
The document provides instructions for removing and installing various engine components on a 308E2CR Mini Hydraulic Excavator, including:
- Removing and installing the diesel particulate filter.
- Removing and installing the inlet manifold.
- Removing and installing the inlet and exhaust valve springs.
- Removing and installing the inlet and exhaust valves.
Detailed step-by-step instructions are provided along with illustrations to guide the process. Safety precautions and notes are included throughout.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...f8useudjkddmm2
The document provides instructions for removing and installing components related to emissions control on a Caterpillar 308E2CR mini hydraulic excavator engine. It describes removing the exhaust gas recirculation valve by draining coolant, removing bolts and hoses, and disconnecting electrical connections. It also details removing the diesel particulate filter by marking positions, removing sensors and bolts, and cleaning components before reassembling in reverse order. Safety precautions are provided throughout for hot and pressurized fluids.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...f8useudjkddmm2
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal, wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures include using various tools to remove components, cleaning parts, applying sealant or oil, and torquing bolts to the specified values. Safety notices are provided to keep parts clean and contain fluids during maintenance.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix TMX) Service Repair ...f8useudjkddmm2
The document provides instructions for removing and installing various engine components on a 308E2CR Mini Hydraulic Excavator including the crankshaft front seal, idler gear, housing (front), valve mechanism cover, bridge dowels, rocker shaft and push rod. The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Safety and installation notes are also provided.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix EC2) Service Repair ...f8useudjkddmm2
This document provides removal and installation instructions for several components of a Caterpillar 308E2CR mini hydraulic excavator engine, including:
1) The fuel injection pump, with steps to mark alignment, remove connections and bolts, and install correctly with torque specifications.
2) Electronic unit injectors, with steps to remove tubes and clamps, install new seals, and tighten to torque specifications.
3) The turbocharger, with steps to remove hoses, bolts, and housing, install new gaskets, and reconnect hoses.
4) The mass air flow pressure sensor, with a step to tilt the radiator for access.
Caterpillar Cat 307E2 Mini Hydraulic Excavator (Prefix KC9) Service Repair Ma...f8useudjkddmm2
The document provides instructions for removing and installing various components of a 307E2 Mini Hydraulic Excavator including the fuel manifold, fuel injection lines, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. The procedures note safety hazards and provide illustrations showing the components and steps to remove and install each part.
More Related Content
Similar to Caterpillar Cat 422E Backhoe Loader (Prefix DSK) Service Repair Manual (DSK00001 and up).pdf
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using punches.
3. Cleaning and aligning the crankshaft flange before pressing the new crankshaft rear seal onto the flange using an alignment tool.
4. Removing bolts to lift the flywheel housing off the engine cylinder block using a lifting device. Inspection and installation steps are also
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment due to the flywheel's weight of approximately 155 pounds. For installing the flywheel, the instructions specify cleaning components, heating the ring gear, lifting the flywheel into place, and tightening bolts to the specified torque. Removing the crankshaft rear seal involves using a socket to remove screws, while installing requires aligning and pressing the new seal onto the crankshaft flange and torquing screws to the specified value.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it with guide bolts and lifting equipment, replacing bolts, and tightening them in sequence.
3) Removing the crankshaft rear seal by taking out torx screws and discarding the seal and housing assembly.
4) Installing the new crankshaft rear seal by aligning it on the crankshaft flange, installing torx
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment. It similarly describes removing the flywheel housing by taking out bolts and checking seals. Reinstallation involves cleaning, installing dowels or seals if needed, and torquing bolts with a lifting device and dial indicator used for alignment.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it with guide bolts and lifting equipment, replacing bolts and checking run out.
3) Removing the crankshaft rear seal by taking out torx screws and discarding the seal and housing assembly.
4) Installing the new crankshaft rear seal by aligning it on the crankshaft flange without lubrication, installing torx
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
Similar to Caterpillar Cat 422E Backhoe Loader (Prefix DSK) Service Repair Manual (DSK00001 and up).pdf (10)
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual (CAM0000...f8useudjkddmm2
This document provides instructions for removing and installing inlet and exhaust valve seats in a 322C FM excavator engine. It outlines the required tools and gives step-by-step procedures for removal and installation. Removal involves using a valve seat extractor tool to pull each seat from the cylinder head. Installation requires tapping new seats into place and ensuring they are flush with the head. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual (C3R0000...f8useudjkddmm2
1. The document provides instructions for removing and installing the unit injector hydraulic pump and turbocharger on a Caterpillar 3126B engine.
2. The unit injector hydraulic pump removal instructions include disconnecting lines and harness, removing mounting bolts, and inspecting seals. Installation is the reverse.
3. Turbocharger removal requires removing bolts from exhaust and oil lines. Disassembly separates housing components. Installation reconnects components and lines.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual (BPH0000...f8useudjkddmm2
This document provides instructions for removing and installing a governor from a 322C FM EXCAVATOR engine. It describes disconnecting linkages, removing mounting bolts and clips, and using special tools. Proper cleaning and lubrication of seals is emphasized. References are provided for additional information on governor inspection and fuel linkage components.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...f8useudjkddmm2
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 320D L excavator. The removal procedure involves using a link bracket and lifting device to remove the flywheel housing after removing bolts and washers. The installation procedure instructs to clean surfaces, apply retaining compound, and use the link bracket to reinstall the flywheel housing and check that the oil seal is correctly installed.
Caterpillar Cat 320D L Excavator (Prefix KLM) Service Repair Manual (KLM00001...f8useudjkddmm2
This document provides instructions for removing the crankshaft front seal from a Caterpillar C6.4 engine. The steps are:
1. Remove the crankshaft pulley using a combination puller tool.
2. Use a suitable chisel and hammer to remove the wear sleeve from the crankshaft pulley, if necessary.
3. Pull out the crankshaft front seal using the appropriate seal removal tool.
Caterpillar Cat 320D L Excavator (Prefix JFZ) Service Repair Manual (JFZ00001...f8useudjkddmm2
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix W8S) Service Repair ...f8useudjkddmm2
The document provides instructions for removing and installing various engine components on a 308E2CR Mini Hydraulic Excavator, including:
- Removing and installing the diesel particulate filter.
- Removing and installing the inlet manifold.
- Removing and installing the inlet and exhaust valve springs.
- Removing and installing the inlet and exhaust valves.
Detailed step-by-step instructions are provided along with illustrations to guide the process. Safety precautions and notes are included throughout.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...f8useudjkddmm2
The document provides instructions for removing and installing components related to emissions control on a Caterpillar 308E2CR mini hydraulic excavator engine. It describes removing the exhaust gas recirculation valve by draining coolant, removing bolts and hoses, and disconnecting electrical connections. It also details removing the diesel particulate filter by marking positions, removing sensors and bolts, and cleaning components before reassembling in reverse order. Safety precautions are provided throughout for hot and pressurized fluids.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...f8useudjkddmm2
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal, wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures include using various tools to remove components, cleaning parts, applying sealant or oil, and torquing bolts to the specified values. Safety notices are provided to keep parts clean and contain fluids during maintenance.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix TMX) Service Repair ...f8useudjkddmm2
The document provides instructions for removing and installing various engine components on a 308E2CR Mini Hydraulic Excavator including the crankshaft front seal, idler gear, housing (front), valve mechanism cover, bridge dowels, rocker shaft and push rod. The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Safety and installation notes are also provided.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix EC2) Service Repair ...f8useudjkddmm2
This document provides removal and installation instructions for several components of a Caterpillar 308E2CR mini hydraulic excavator engine, including:
1) The fuel injection pump, with steps to mark alignment, remove connections and bolts, and install correctly with torque specifications.
2) Electronic unit injectors, with steps to remove tubes and clamps, install new seals, and tighten to torque specifications.
3) The turbocharger, with steps to remove hoses, bolts, and housing, install new gaskets, and reconnect hoses.
4) The mass air flow pressure sensor, with a step to tilt the radiator for access.
Caterpillar Cat 307E2 Mini Hydraulic Excavator (Prefix KC9) Service Repair Ma...f8useudjkddmm2
The document provides instructions for removing and installing various components of a 307E2 Mini Hydraulic Excavator including the fuel manifold, fuel injection lines, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. The procedures note safety hazards and provide illustrations showing the components and steps to remove and install each part.
Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Man...f8useudjkddmm2
The document provides instructions for removing and installing various engine components on a 307D Mini Hydraulic Excavator including the fuel filter and water separator base, engine oil filter and oil filter base, and air cleaner. The procedures describe draining fluids, disconnecting hoses, removing bolts and filters, cleaning parts, applying oil, and reinstalling components in the reverse order of removal. Safety precautions are provided to prevent injury and contain fluids.
This service repair manual provides instructions for removing and installing the fuel injection pump on Caterpillar 3054 engines. The document outlines the required tools and steps to:
1) Remove the fuel injection pump by loosening locking screws, aligning timing holes, and removing mounting bolts and nuts.
2) Install the fuel injection pump by checking and installing o-rings, aligning timing marks, inserting timing pins, and tightening mounting hardware while ensuring proper timing.
3) The process involves precautions like keeping parts clean, containing fluids, and setting the engine to top dead center before removing or installing the pump.
Caterpillar Cat 307 EXCAVATOR (Prefix 2WM) Service Repair Manual (2WM00001-00...f8useudjkddmm2
This document provides instructions for removing and installing pistons, connecting rods, and connecting rod bearings on a 307 excavator. The summary is:
1) Remove the cylinder head, engine oil pump, and piston cooling jets to access the connecting rods.
2) Use ridge reaming and press tools to remove the piston pins, rings, and bushings from the pistons and connecting rods.
3) Clean all components thoroughly before disassembly and assembly to prevent contaminants from causing premature wear.
This document provides instructions for servicing components related to the crankshaft on a Caterpillar C3.3B engine, including:
1. Removing and installing the flywheel, which involves using guide studs and lifting equipment due to its weight of approximately 30 kg.
2. Removing the crankshaft rear seal, crankshaft gear, and wear sleeve, and inspecting these components for wear and damage.
3. Installing the crankshaft rear seal, crankshaft gear, and wear sleeve, which requires aligning gears and using a press and driver tool.
4. Removing and installing the flywheel housing, which mounts to the cylinder block
This document provides instructions for removing and installing various engine components on a 272D Skid Steer Loader, including the flywheel, crankshaft rear seal, crankshaft rear seal carrier, and flywheel housing. The flywheel removal procedure involves removing mounting bolts and lifting devices. Installation requires cleaning, applying oil to bolts, and tightening to the specified torque. The crankshaft rear seal and carrier involve using drivers to remove and install sealing rings and lips. Flywheel housing removal uses lifting devices and bolts, while installation applies adhesive and tightens bolts to the appropriate torque.
This service repair manual provides instructions for removing and installing various engine components on a 262D Skid Steer Loader with a C3.3B engine, including the engine oil pump, water pump, water temperature regulator, flywheel, crankshaft rear seal and wear sleeve. The procedures provide detailed steps and illustrations for each component, with notes about cleaning parts and using the proper tools and torque specifications.
This document provides instructions for installing and removing the fuel injection pump on a 262D Skid Steer Loader with a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting bolts and nuts, and installing replacement gasket shims. Special tools are required to remove the pump. Cleanliness of all fuel system components is critical during installation to prevent contamination.
This document provides instructions for removing and installing exhaust manifolds, inlet and exhaust valves, and inlet and exhaust valve springs on Caterpillar 249D compact track loaders. The procedures describe using various tools to compress springs, remove bolts and nuts, and install new gaskets and components. Safety notices are included to warn technicians to keep parts clean, plug openings, and wear protective equipment when working with compressed springs.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 422E BACKHOE LOADER DSK
Configuration: 422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763425
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Bolt
(1/2 inch - UNF by 4 inch)
2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01245126
Typical example
1. Remove two bolts from positions (X) on flywheel (1).
2. Install Tooling (A) to positions (X) on flywheel (1).
3. Attach a suitable lifting device to flywheel (1). Support the weight of the flywheel. The
weight of the flywheel is approximately 71 kg (155 lb).
4. Remove remaining bolts (2).
5. Use the lifting device in order to remove the flywheel from the engine.
2/3
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01245152
Typical example
6. Inspect flywheel (1) and ring gear (3) for wear or damage. Replace any components that are
worn or damaged.
7. To remove the flywheel ring gear, follow Steps 7.a and 7.b.
a. Place the flywheel assembly on a suitable support.
Note: Identify the orientation of the teeth on the flywheel ring gear.
b. Use a hammer and a punch in order to remove ring gear (3) from flywheel (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 29 23:26:18 UTC+0800 2019
3/3
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 422E BACKHOE LOADER DSK
Configuration: 422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i07030539
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Bolt
(1/2 inch - 20 UNF by 4 inch)
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g01343963
Typical example
Always wear protective gloves when handling parts that have been
heated.
1. If the flywheel ring gear was removed, follow Steps 1.a through 1.c to install a new ring
gear to the flywheel.
a. Identify the orientation of teeth (4) on the new ring gear (4).
Note: The chamfered side of the ring gear teeth must face toward the starting motor
when the flywheel is installed. The correct orientation of the chamfered will ensure
the correct engagement of the starting motor.
b. Heat flywheel ring gear (3) in an oven to a maximum temperature of 250 °C (482 °F)
prior to installation.
Note: Do not use a torch to heat the ring gear.
c. Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear
onto flywheel (1).
2. Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft
rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" for the
correct procedure.
2/4
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 2 g01245126
Typical example
3. Install a suitable lifting device to flywheel (1). The flywheel weighs approximately 71 kg
(155 lb).
4. Install Tooling (A) to positions (X) on the crankshaft.
5. Use the lifting device to position flywheel (1) onto Tooling (A).
6. Install bolts (2) to flywheel (1) finger tight.
7. Remove Tooling (A) and install remaining bolts (2) to flywheel (1).
8. Remove the lifting device from flywheel (1).
9. Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) to a torque of
140 N·m (103 lb ft).
10. Check the run out of the flywheel. Refer to System Operation, Test, and Adjusting,
"Flywheel - Inspect" for further information.
End By:
a. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
3/4
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 422E BACKHOE LOADER DSK
Configuration: 422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763427
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4390 E12 Torx Socket 1
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Dispose of all fluids according to local regulations and mandates.
Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly. The
assembly is not serviceable. If the crankshaft rear seal is removed, the assembly must be replaced.
Illustration 1 g01269512
Typical example
1. Use Tooling (A) in order to remove torx screws (1) from crankshaft rear seal (2).
2. Remove crankshaft rear seal (2) from the cylinder block. Discard the crankshaft rear seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 29 23:28:09 UTC+0800 2019
2/2
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 422E BACKHOE LOADER DSK
Configuration: 422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763428
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4390 E12 Torx Socket 1
B FT-2806 Alignment Tool 1
Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g01258105
Illustration 2 g01255709
Typical example
1. Ensure that crankshaft flange (1) is clean, dry and free from damage.
2. Ensure that the face of the cylinder block and the bridge piece are clean and dry.
3. A new crankshaft rear seal is supplied with a plastic sleeve (3). Ensure that the plastic
sleeve is squarely installed within crankshaft rear seal (2).
Note: The plastic sleeve is included in order to protect the lip of the seal as the seal is
pushed over the crankshaft flange.
Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The
crankshaft rear seal must be installed dry.
2/4
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 4. Align plastic sleeve (3) with crankshaft flange (1). Ensure that the plastic sleeve is engaged
onto the crankshaft flange. Push new crankshaft rear seal (2) squarely onto the crankshaft
flange.
During this process, the plastic sleeve will be forced out of the crankshaft rear seal. Discard
the plastic sleeve.
5. Align the two molded locators on crankshaft rear seal (2) with the holes in the cylinder
block. Ensure that the crankshaft rear seal is seated against the cylinder block.
Illustration 3 g01258357
Tightening sequence for the crankshaft rear seal
6. Install torx screws (4) finger tight.
Note: Do not install torx screws to positions (X) at this stage.
7. Install Tooling (B) to crankshaft rear seal (2) and to crankshaft flange (1).
8. Use Tooling (A) in order to tighten torx screws (4) to a torque of 22 N·m (16 lb ft). Tighten
torx screws (4) in the sequence that is shown in Illustration 3.
9. Remove Tooling (B).
10. Install remaining torx screws (4) to positions (X). Use Tooling (A) in order to tighten the
torx screws to a torque of 22 N·m (16 lb ft). Refer to Illustration 3.
3/4
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 29 23:29:05 UTC+0800 2019
4/4
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 422E BACKHOE LOADER DSK
Configuration: 422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763429
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Install a suitable lifting device to the flywheel housing in order to support the flywheel
housing. The flywheel housing weighs approximately 30 kg (66 lb).
1/5
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
16. Illustration 1 g01244050
Typical example
2. Remove bolts (2) and bolts (3) from flywheel housing (1).
3. Use the lifting device in order to remove flywheel housing (1) from the cylinder block.
Illustration 2 g01244051
2/5
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Typical example
4. If the engine has an aluminum oil pan, remove dust seal (5).
5. If necessary, remove dowels (4) from the cylinder block.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
(M10 by 100 mm)
2
B 8T-5096 Dial Indicator Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the flywheel housing is clean and free from damage. If necessary, replace the
flywheel housing.
Illustration 3 g01244056
Typical example
3/5
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 2. Inspect crankshaft rear seal (6) for leaks. If there are any oil leaks, replace the crankshaft
rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and refer
to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
3. Clean the rear face of the cylinder block. If necessary, install dowels (4) to the cylinder
block.
4. Install Tooling (A) to the cylinder block.
5. Install dust seal (5).
Illustration 4 g01244050
Typical example
6. Install a suitable lifting device to the flywheel housing. The flywheel housing weighs
approximately 30 kg (66 lb).
7. Use the lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel
housing to the cylinder block.
8. Install bolts (2) and bolts (3) finger tight.
9. Remove Tooling (A). Install remaining bolts (3).
10. Tighten bolts (3) to a torque of 63 N·m (46 lb ft).
11. Tighten bolts (2) to a torque of 75 N·m (55 lb ft).
4/5
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 12. Use Tooling (B) to check the alignment of the flywheel housing with the crankshaft. Refer
to Systems Operation, Testing and Adjusting, "Flywheel Housing - Inspect".
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 29 23:30:01 UTC+0800 2019
5/5
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...