The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal, wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures include using various tools to remove components, cleaning parts, applying sealant or oil, and torquing bolts to the specified values. Safety notices are provided to keep parts clean and contain fluids during maintenance.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242540
Crankshaft Rear Seal and Wear Sleeve - Remove - Includes
Crankshaft Gear
SMCS - 1161-011; 7558-011
Removal Procedure
Start By:
a. Remove the flywheel.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Place the engine at top dead center.
1/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g02799897
2. Use a screw driver to remove rear seal (1).
Illustration 2 g02799899
3. Check the alignment of crankshaft gear (2) and camshaft gear (3). Remove crankshaft gear
(2) and ring seal.
Illustration 3 g02799901
4. Place crankshaft gear (2) with wear sleeve (4) in a suitable vice. Remove wear sleeve (4)
with a suitable chisel.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:04:48 UTC+0800 2020
2/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242547
Crankshaft Rear Seal and Wear Sleeve - Install - Includes
Crankshaft Gear
SMCS - 1161-012; 7558-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
390-1146 Crankshaft Rear Seal and Wear Sleeve Driver(1)
1
423-9665 Crank shaft Rear Seal and Wear Sleeve Driver(2)
1
(1)
Used for the C3.3B
(2)
Used for the C2.6
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
1/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g02800138
1. Place wear sleeve (4) on crankshaft gear (2). Position Tooling (A). Use a suitable press and
install wear sleeve (4).
Illustration 2 g02799899
2. Align crankshaft gear (2) with camshaft gear (3). Install crankshaft gear (2) into the
flywheel housing.
Illustration 3 g02800140
3. Apply clean engine oil on the lip of crankshaft rear seal (1). Use Tooling (A) in order to
install crankshaft rear seal (1).
End By:
a. Install the flywheel.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:05:44 UTC+0800 2020
2/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242551
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M12 x 1.25 by 100 mm
2
B 138-7575 Link Brackets 2
Start By:
a. Remove the flywheel.
b. Remove the rear crankshaft seal.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g02794824
1. Remove two bolts (3) from flywheel housing (1).
2. Install Tooling (A) into flywheel housing (1).
3. Install Tooling (B). Install a suitable lifting device to flywheel housing (1). The weight of
flywheel housing (1) is approximately 25 kg (55 lb).
4. Remove remaining six bolts (3) and 8 bolts (2) from flywheel housing (1).
5. Remove flywheel housing (1) from the cylinder block.
Illustration 2 g02794825
6. Remove bearing (4).
7. Remove the gasket (5).
8. If necessary, remove the dowels from the cylinder block.
Installation Procedure
1. Install flywheel housing (1) in the reverse order of removal.
2/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g02863884
a. Install liquid gasket to the seam between the lower crankcase section (7) and the
upper crankcase section (6).
b. For the C3.3B tighten 8 bolts (3) and 8 bolts (2) to a torque of 103 to 117 N·m
(76 to 87 lb ft).
c. For the C2.6 tighten 8 bolts (3) and 8 bolts (2) to a torque of 78 to 90 N·m
(58 to 66 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:06:41 UTC+0800 2020
3/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242553
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
a. Remove the v-belt.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g02795206
1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove bolt (2) in order
to remove crankshaft pulley (1).
Installation Procedure
1. Install crankshaft pulley (1) in the reverse order of removal.
a. Apply clean engine oil to the threads of bolt (2). Tighten bolt (2) to a torque of
255 to 274 N·m (188 to 202 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:07:38 UTC+0800 2020
2/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242559
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Start By:
a. Remove the crankshaft pulley.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g02795123
Illustration 2 g02795124
1. Use a suitable pry bar to remove crankshaft front seal (1).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 390-1140 Driver 1
B 6V-6640 Sealant 1
Note: The crankshaft front seal should be installed dry. Lubricate the inner rubber portion of the
crankshaft front seal.
2/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 3 g02796112
Illustration 4 g02795123
1. Lubricate the inner rubber portion of crankshaft front seal (1). Apply Tooling (B) on
crankshaft front seal (1). Position crankshaft front seal (1) on Tooling (A). Install crankshaft
front seal (1) on the crankshaft.
End By:
a. Install the crankshaft pulley.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:08:35 UTC+0800 2020
3/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02795977
3/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g02795978
Illustration 3 g02795981
Alignment of timing marks
1. Ensure that Timing Marks (X) on the camshaft gear and the crankshaft gear are aligned.
Refer to Illustration 1.
2. Ensure that Timing Marks (Y) on the idler gear and the camshaft gear are aligned. Refer to
Illustration 2.
3. Ensure that Timing Marks (Z) on the idler gear and the fuel injection pump gear are aligned.
Refer to Illustration 3.
4/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. Illustration 4 g02795984
4. Remove bolts (2), washer (3), and the idler shaft from idler gear (1). Remove idler gear (1)
and the washer.
Illustration 5 g02795985
5. Use Tooling (A) to remove idler gear bearing (4) from idler gear (1).
Installation Procedure
1. Install idler gear (1) in the reverse order of removal.
2. Tighten bolts (2) to a torque of 30 to 34 N·m (22 to 25 lb ft).
a. Ensure that the gears, cylinder block surface, and idler gear (1) are clean and free
from wear or damage. If necessary, replace any components that are worn or
damaged.
b. Lubricate idler gear bearing surface (4) with clean engine oil.
c. Check oil clearance between the idler gear shaft and the idler gear bushing.
d. Check the idler gear shaft outer diameter and the inner diameter for the idler gear
bushing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:09:32 UTC+0800 2020
5/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Illustration 1 g02795275
2. Disconnect hose assemblies (1) and (2) from the oil cooler.
Illustration 2 g02795251
3. Remove bolts (4).
3/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 4. Remove front housing (3) and the gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the front housing is clean and free from damage. If necessary, replace the front
housing.
2. Clean all the gasket surfaces of the cylinder block.
Illustration 3 g02864317
3. Apply liquid gasket to the seam between the lower crankcase section (6) and the upper
crankcase section (5).
4/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 4 g02795251
4. Align a new gasket and install the gasket to the cylinder block.
5. Tighten 13 bolts (4) in a side to side sequence. Tighten bolts (4) to a torque of 24 to 27 N·m
(18 to 20 lb ft)
Illustration 5 g02795275
6. Connect hose assemblies (1) and (2) to the oil cooler.
End By:
a. Install the crankshaft front seal.
b. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling
System Coolant - Fill" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:10:28 UTC+0800 2020
5/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...