The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual Instant D...fucheng89
The document provides instructions for assembling a travel motor. It lists the required tools and begins by noting the importance of cleanliness. It then provides 33 steps detailing how to install seals, spacers, pistons, disks, bearings and other components into the travel motor housing. It concludes by noting the travel motor should be filled with oil prior to operation.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual Instant D...f89siekkmdmm2w
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, disks and shafts. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual Instant D...f8uejkdkdmm3e
This document provides instructions for installing a travel motor on an excavator. It outlines 33 steps for assembling components like seals, pistons, plates, and valves. Proper measurement is required at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system. The motor must be filled with the specified oil type before operation.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual Instant D...shibi1322
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, disks and shafts. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual Instant D...8foskkdjdkdm3e
This document provides instructions for installing a travel motor. It outlines 33 steps for assembling components like seals, pistons, plates, and valves. Measurements are checked at several points to ensure proper assembly. The motor is filled with oil at the end to prevent damage before operation.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual Instant D...jiazhi27185
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix wtd) service repair manual (wtd0000...didkkskdmmd
The document provides instructions for assembling a travel motor. It lists the required tools and begins by noting the importance of cleanliness. It then provides 33 steps describing how to install seals, spacers, pistons, disks, bearings and other components into the travel motor housing and barrel. It concludes by stating the travel motor should be filled with the correct oil specification prior to operation.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual (WTD00001...km7seyrduhdw
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, disks and shafts. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual Instant D...fucheng89
The document provides instructions for assembling a travel motor. It lists the required tools and begins by noting the importance of cleanliness. It then provides 33 steps detailing how to install seals, spacers, pistons, disks, bearings and other components into the travel motor housing. It concludes by noting the travel motor should be filled with oil prior to operation.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual Instant D...f89siekkmdmm2w
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, disks and shafts. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual Instant D...f8uejkdkdmm3e
This document provides instructions for installing a travel motor on an excavator. It outlines 33 steps for assembling components like seals, pistons, plates, and valves. Proper measurement is required at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system. The motor must be filled with the specified oil type before operation.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual Instant D...shibi1322
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, disks and shafts. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual Instant D...8foskkdjdkdm3e
This document provides instructions for installing a travel motor. It outlines 33 steps for assembling components like seals, pistons, plates, and valves. Measurements are checked at several points to ensure proper assembly. The motor is filled with oil at the end to prevent damage before operation.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual Instant D...jiazhi27185
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix wtd) service repair manual (wtd0000...didkkskdmmd
The document provides instructions for assembling a travel motor. It lists the required tools and begins by noting the importance of cleanliness. It then provides 33 steps describing how to install seals, spacers, pistons, disks, bearings and other components into the travel motor housing and barrel. It concludes by stating the travel motor should be filled with the correct oil specification prior to operation.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual (WTD00001...km7seyrduhdw
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, disks and shafts. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual Instant D...yin9niaojiao
This document provides instructions for installing a travel motor. It outlines 33 steps including installing seals, spacers, pistons, disks, bearings and other components. Measurements are taken throughout to ensure proper assembly. O-rings and seals must be replaced and components cleaned to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix wtd) service repair manual (wtd0000...cdsaas
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix wtd) service repair manual (wtd0000...fjskekxcddmmme
This document provides instructions for installing a travel motor on an excavator. It outlines 33 steps for assembling components like seals, pistons, plates, and bearings inside the motor housing. Measurements are checked at several points to ensure proper assembly. Finally, the motor is filled with oil and installed on the excavator.
Caterpillar cat 349 d l excavator (prefix wtd) service repair manual (wtd0000...hhfjksekmm
This document provides instructions for installing a travel motor on an excavator. It outlines 33 steps for assembling components like seals, pistons, plates, and valves. Proper measurement is required at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system. The motor must be filled with the specified oil type before operation.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for installing a travel motor. It outlines 33 steps for assembling components like seals, pistons, plates, and valves. Measurements are checked at several points to ensure proper assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for assembling and installing a travel motor. It outlines 34 steps for assembling components like pistons, seals, plates, and bearings. It also describes using tools to measure clearances and distances during assembly. Finally, it details installing the assembled travel motor using lifting devices and bolts, and connecting hydraulic hose assemblies.
The document provides step-by-step instructions to disassemble the output transfer gears of a 745C Articulated Truck. It lists 49 steps to remove components like the output transfer gears case, yokes, seals, bearings, gears, shafts, and seals. Special tools are required to remove some components and safety precautions are provided given the heavy weight of some parts that need to be lifted.
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
The document provides instructions for assembling and disassembling the piston pump used in Caterpillar 745 articulated trucks. The assembly instructions include installing various seals, springs, and other components in the proper order and orientation. Disassembly is performed by removing these same components in the reverse order. Pictures and diagrams accompany the text to illustrate each step. Safety warnings are provided to prevent injury from released spring forces during disassembly.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 740B Ejector Articulated Truck powered by a C15 engine. The removal procedure involves removing bolts and other components to detach the housing. For installation, the procedure describes cleaning parts, applying sealant, positioning seals and gears, and torquing bolts to specified values. Additional components like the rear power take-off must be removed before and reinstalled after the flywheel housing job.
This document provides disassembly instructions for the output transfer gears of a 740B articulated truck. It lists over 50 steps to remove various components such as planetary gears, shafts, seals, bearings, and housings. Special tools are required to remove some parts, and components can weigh up to 630 kg so lifting devices are needed. Detailed illustrations accompany each step to show the specific components and fasteners.
This document provides instructions for removing the camshaft from a Caterpillar C15 engine. The procedure involves:
1. Removing components like the camshaft gear and rocker arms
2. Removing bolts and plates connecting the camshaft to hold it in place
3. Installing tooling to support the camshaft as it is slid out of the engine, being careful not to damage surfaces
4. Slowly sliding the camshaft forward and out of the engine using hooks for support, keeping it level throughout removal
The document provides instructions for installing the front cover on a C15 engine. It describes:
1. Cleaning the front housing sealing surface.
2. Installing a new seal into the front cover.
3. Positioning the front cover with installed seal on the front housing using alignment studs.
4. Installing spacers, nuts, and button head screws and tightening to the specified torque.
The document provides instructions for disassembling and assembling components of the gear pump and piston pump used in Caterpillar 740 GC articulated trucks. The gear pump section describes removing and installing the gear pump, housing, seals, gears, and other internal parts. The piston pump section outlines removing the pump head, springs, spools, pistons, bearings, and separating the rotating group from the pump housing. Detailed illustrations accompany each step to ensure safe and proper disassembly and reassembly of the pumps.
This document provides instructions for installing and removing the ejector blade carriage on a 740 Ejector Articulated Truck. It describes using lifting equipment and blocking to safely handle the 210 kg carriage component. The 10-step removal procedure includes loosening lock rings, bolts, and other hardware to separate the carriage from the machine. The 11-step installation procedure specifies replacing hardware in reverse order and adjusting components like floor rollers. Cleaning parts and noting shim positions are emphasized for correct reassembly.
The document provides instructions for disassembling a gear pump used in Caterpillar 740 articulated trucks. The disassembly procedure involves:
1. Removing fittings from the pump body and O-rings from the fittings.
2. Removing bolts securing a flange to the pump body and an O-ring from the flange.
3. Using retaining ring pliers to remove two rings from the flange and a lip seal from the flange.
The document provides instructions for removing and installing a steering cylinder on a 740 articulated truck. It lists the required tools which include chocks, a hydraulic cylinder tool, and washers. The steps include chocking the wheels, disconnecting grease lines if needed, and using a tool and washers to secure the rod end of the cylinder before removing mounting bolts and taking it off the vehicle. Reinstallation follows the removal steps in reverse order.
The document provides instructions for removing and installing various engine components on a Caterpillar C15 engine, including:
1. Removing and installing the rear power take-off, which involves installing bushings and covers in the flywheel housing.
2. Removing and installing the vibration damper and pulley, which requires using tools to lift and position the components.
3. Procedures for removing and installing the crankshaft front seal, which includes using a slide hammer and seal installer tool.
The document contains detailed step-by-step instructions accompanied by illustrations and notes about keeping components clean and applying anti-seize compound as needed.
This document provides instructions for removing and installing various components of a C13 engine, including:
- The flywheel housing
- The vibration damper and pulley
- The crankshaft front seal
- The front cover
- The front gear group
- The front housing
- Accessory drive brackets and pulleys
- The fumes disposal filter
- The valve mechanism cover
The procedures include lists of required tools and step-by-step instructions for each removal and installation. Illustrations are provided to supplement the text instructions.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings and covers. The installation procedure provides steps to install these components in reverse order and includes cleaning and applying threadlocker to bolts. Tools required are also listed.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The pump drive removal procedure involves detaching the torque converter housing and shield assembly, then removing bolts and the pump drive unit. The pump drive disassembly requires removing manifold bolts and parts, races, and the carrier assembly.
The document provides instructions for removing and disassembling a torque converter from a Caterpillar 730C2 articulated truck. It describes 18 steps to disassemble the torque converter and 19 steps to reassemble it. Tools required include an adapter plate, engine stand, oil drain cart, and link brackets. Safety precautions are provided to contain fluids and protect from spring forces.
More Related Content
Similar to Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant Download.pdf
Caterpillar Cat 349D L Excavator (Prefix WTD) Service Repair Manual Instant D...yin9niaojiao
This document provides instructions for installing a travel motor. It outlines 33 steps including installing seals, spacers, pistons, disks, bearings and other components. Measurements are taken throughout to ensure proper assembly. O-rings and seals must be replaced and components cleaned to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix wtd) service repair manual (wtd0000...cdsaas
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix wtd) service repair manual (wtd0000...fjskekxcddmmme
This document provides instructions for installing a travel motor on an excavator. It outlines 33 steps for assembling components like seals, pistons, plates, and bearings inside the motor housing. Measurements are checked at several points to ensure proper assembly. Finally, the motor is filled with oil and installed on the excavator.
Caterpillar cat 349 d l excavator (prefix wtd) service repair manual (wtd0000...hhfjksekmm
This document provides instructions for installing a travel motor on an excavator. It outlines 33 steps for assembling components like seals, pistons, plates, and valves. Proper measurement is required at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system. The motor must be filled with the specified oil type before operation.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for installing a travel motor. It outlines 33 steps for assembling components like seals, pistons, plates, and valves. Measurements are checked at several points to ensure proper assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for assembling and installing a travel motor. It outlines 34 steps for assembling components like pistons, seals, plates, and bearings. It also describes using tools to measure clearances and distances during assembly. Finally, it details installing the assembled travel motor using lifting devices and bolts, and connecting hydraulic hose assemblies.
Similar to Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant Download.pdf (6)
The document provides step-by-step instructions to disassemble the output transfer gears of a 745C Articulated Truck. It lists 49 steps to remove components like the output transfer gears case, yokes, seals, bearings, gears, shafts, and seals. Special tools are required to remove some components and safety precautions are provided given the heavy weight of some parts that need to be lifted.
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
The document provides instructions for assembling and disassembling the piston pump used in Caterpillar 745 articulated trucks. The assembly instructions include installing various seals, springs, and other components in the proper order and orientation. Disassembly is performed by removing these same components in the reverse order. Pictures and diagrams accompany the text to illustrate each step. Safety warnings are provided to prevent injury from released spring forces during disassembly.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 740B Ejector Articulated Truck powered by a C15 engine. The removal procedure involves removing bolts and other components to detach the housing. For installation, the procedure describes cleaning parts, applying sealant, positioning seals and gears, and torquing bolts to specified values. Additional components like the rear power take-off must be removed before and reinstalled after the flywheel housing job.
This document provides disassembly instructions for the output transfer gears of a 740B articulated truck. It lists over 50 steps to remove various components such as planetary gears, shafts, seals, bearings, and housings. Special tools are required to remove some parts, and components can weigh up to 630 kg so lifting devices are needed. Detailed illustrations accompany each step to show the specific components and fasteners.
This document provides instructions for removing the camshaft from a Caterpillar C15 engine. The procedure involves:
1. Removing components like the camshaft gear and rocker arms
2. Removing bolts and plates connecting the camshaft to hold it in place
3. Installing tooling to support the camshaft as it is slid out of the engine, being careful not to damage surfaces
4. Slowly sliding the camshaft forward and out of the engine using hooks for support, keeping it level throughout removal
The document provides instructions for installing the front cover on a C15 engine. It describes:
1. Cleaning the front housing sealing surface.
2. Installing a new seal into the front cover.
3. Positioning the front cover with installed seal on the front housing using alignment studs.
4. Installing spacers, nuts, and button head screws and tightening to the specified torque.
The document provides instructions for disassembling and assembling components of the gear pump and piston pump used in Caterpillar 740 GC articulated trucks. The gear pump section describes removing and installing the gear pump, housing, seals, gears, and other internal parts. The piston pump section outlines removing the pump head, springs, spools, pistons, bearings, and separating the rotating group from the pump housing. Detailed illustrations accompany each step to ensure safe and proper disassembly and reassembly of the pumps.
This document provides instructions for installing and removing the ejector blade carriage on a 740 Ejector Articulated Truck. It describes using lifting equipment and blocking to safely handle the 210 kg carriage component. The 10-step removal procedure includes loosening lock rings, bolts, and other hardware to separate the carriage from the machine. The 11-step installation procedure specifies replacing hardware in reverse order and adjusting components like floor rollers. Cleaning parts and noting shim positions are emphasized for correct reassembly.
The document provides instructions for disassembling a gear pump used in Caterpillar 740 articulated trucks. The disassembly procedure involves:
1. Removing fittings from the pump body and O-rings from the fittings.
2. Removing bolts securing a flange to the pump body and an O-ring from the flange.
3. Using retaining ring pliers to remove two rings from the flange and a lip seal from the flange.
The document provides instructions for removing and installing a steering cylinder on a 740 articulated truck. It lists the required tools which include chocks, a hydraulic cylinder tool, and washers. The steps include chocking the wheels, disconnecting grease lines if needed, and using a tool and washers to secure the rod end of the cylinder before removing mounting bolts and taking it off the vehicle. Reinstallation follows the removal steps in reverse order.
The document provides instructions for removing and installing various engine components on a Caterpillar C15 engine, including:
1. Removing and installing the rear power take-off, which involves installing bushings and covers in the flywheel housing.
2. Removing and installing the vibration damper and pulley, which requires using tools to lift and position the components.
3. Procedures for removing and installing the crankshaft front seal, which includes using a slide hammer and seal installer tool.
The document contains detailed step-by-step instructions accompanied by illustrations and notes about keeping components clean and applying anti-seize compound as needed.
This document provides instructions for removing and installing various components of a C13 engine, including:
- The flywheel housing
- The vibration damper and pulley
- The crankshaft front seal
- The front cover
- The front gear group
- The front housing
- Accessory drive brackets and pulleys
- The fumes disposal filter
- The valve mechanism cover
The procedures include lists of required tools and step-by-step instructions for each removal and installation. Illustrations are provided to supplement the text instructions.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings and covers. The installation procedure provides steps to install these components in reverse order and includes cleaning and applying threadlocker to bolts. Tools required are also listed.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The pump drive removal procedure involves detaching the torque converter housing and shield assembly, then removing bolts and the pump drive unit. The pump drive disassembly requires removing manifold bolts and parts, races, and the carrier assembly.
The document provides instructions for removing and disassembling a torque converter from a Caterpillar 730C2 articulated truck. It describes 18 steps to disassemble the torque converter and 19 steps to reassemble it. Tools required include an adapter plate, engine stand, oil drain cart, and link brackets. Safety precautions are provided to contain fluids and protect from spring forces.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides instructions for removing and installing an engine from a 730C Ejector Articulated Truck. It outlines 25 steps to remove the engine, including disconnecting wiring harnesses, hoses, brackets and removing bolts. It then states the installation is done in reverse order. A second document provides instructions for releasing pressure from the hydraulic system before disassembly, including moving components and removing filler caps. A third document outlines 14 steps to disassemble a torque converter, including removing housing, rings, plates and discs.
The document provides instructions for disassembling and assembling the torque converter of a 730C articulated truck. It describes 18 steps to disassemble the torque converter by removing housing assemblies, bearings, plates, discs, seals, and other components. It then describes 13 steps to assemble the torque converter by installing these same components in the reverse order, taking care to keep parts clean and follow procedures carefully due to parts that are spring loaded. Special tools are required for many steps, and safety precautions are provided.
This document provides assembly instructions for a torque converter in a 730 articulated truck. It lists 43 steps to assemble the torque converter components in the proper order, attaching seals, bearings, housings and other parts. It also provides illustrations matching each step. The final steps are to connect the assembled torque converter to the planetary transmission and lists the starting steps to remove the torque converter housing.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D L EXCAVATOR KHS
Configuration: 349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile
Hydraulic Power Units Machine Systems
Media Number -RENR9574-10 Publication Date -01/08/2014 Date Updated -18/09/2018
i03778971
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 3E-3879 Eyebolt 1
D 4C-8359 Eyebolt 1
F 1P-1862 Pliers 1
G 1P-0510 Driver Group 1
J 4C-4030 Thread Lock Compound 1
K 180-6533 Seal Driver 1
L 6V-7030 Micrometer Depth Gauge 1
M 8T-0447 Calipers 1
N 1U-6396 O-Ring Assembly Compound 1
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
1/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline For Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
Note: O-ring seals , gaskets, and seals should always be replaced. A used O-ring seal may not
have the same sealing properties as a new O-ring seal. Use Tooling (H) during the assembly
procedure.
Note: Apply a light film of "10W" oil to all components before assembly.
Illustration 1 g01204890
1. Install O-ring seal (34) on plug (33).
2. Install piston (32) and the plug in the travel motor body. Tighten the plug to a torque of
430 ± 40 N·m (317 ± 30 lb ft).
2/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01204916
Illustration 3 g01204919
3. Apply a thin coat of Tooling (J) on the outer surfaces of lip seal (31).
4. Use Tooling (K) and a suitable hammer to drive the lip seal into the travel motor body.
Drive the seal downward until Tooling (K) makes contact with the travel motor housing.
5. Use Tooling (F) to install retaining ring (30) to the shaft end of the travel motor body.
Illustration 4 g01204923
6. Install keys (29) inside the travel motor body.
3/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01204924
7. Assemble washers (25), inner spacer (28) and outer spacer (27) in the proper orientation, as
shown.
Illustration 6 g01204931
8. Use Tooling (L) to measure the distance from the outer spacer to the surface of the table.
The distance should be 22.1 ± 0.6 mm (0.87 ± 0.02 inch). If this measurement is off, check
orientation of the washers. If orientation is correct, replace washers and spacers with new
parts.
4/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g00625917
9. Install inner spacer (28), washers (25), and outer spacer (27) to barrel (24).
10. Install guide (26) to the barrel.
Illustration 8 g00625911
11. Install piston assemblies (23) with retainer (22) in the piston assembly's original bore in
barrel (24).
Illustration 9 g00625908
12. Install cam plate (21) on the rotating group.
5/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g00666621
Illustration 11 g00628062
13. Use a suitable press to install bearing (19) onto shaft assembly (18).
Illustration 12 g00668076
14. Use a suitable press in order to install inner race (20) onto shaft assembly (18).
Note: Place the two support plates under the lip of shaft assembly (18).
6/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g00626633
15. Insert shaft assembly (18) in the rotating group.
Illustration 14 g00625891
Illustration 15 g00666743
16. Alternate disks (17) and separator plates (16) into the travel motor housing. Start with a
separator plate and end with a separator plate.
7/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 16 g00626837
17. Attach Tooling (D) to the shaft. Use a suitable lifting device in order to place barrel
assembly into the travel motor body.
Note: Align the notches of the cam plate with the keys in the travel motor body before you
lower the barrel assembly into the travel motor body.
Illustration 17 g01204938
18. Use Tooling (M) to measure the depth from the top surface of the travel motor body to the
bronze face of the barrel assembly. The distance should be 32.2 ± 2 mm (1.27 ± 0.08 inch).
If this measurement is off, check orientation of the barrel assembly. Also check if the cam
plate is properly seated on the keys.
8/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g00625888
Illustration 19 g00667938
(15) O-Ring seals
19. Install O-ring seals (15) and the backup rings on the brake piston.
Note: Make sure that you install the backup ring and the O-ring seal in the original position.
Refer to Illustration 19.
9/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g00629015
20. Install brake piston (14) in the body of the travel motor by hand. It may be necessary to use
a soft faced hammer to seat the brake piston correctly.
Illustration 21 g01204953
21. Use Tooling (M) to measure the distance from the top of the brake piston (14) to the top
surface of the travel motor body. The distance should be 20.8 ± 1.0 mm (0.82 ± 0.04 inch).
If this measurement is off, drive the brake piston further into the travel motor body.
Illustration 22 g00627391
22. Install springs (12) and plate (11).
10/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 23. Install O-ring seals (13).
Illustration 23 g01204965
24. Use Tooling (G) to drive the bearing into the head.
Illustration 24 g00627405
25. Install O-ring seal (9) onto the head.
26. Install port plate (8) on the head. It may be necessary to apply a small amount of grease to
the port plate in order to hold the port plate in place during the installation of the head.
Illustration 25 g01205007
11/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 27. Turn over head (6). Install Tooling (A) onto the head. Use a suitable lifting device to install
the head onto the travel motor.
Illustration 26 g00631594
28. Install Pins (7) into the head.
Illustration 27 g00628657
29. Install an O-ring on each plug (5).
30. Install bolts (4) which hold the head in place. Tighten the six bolts to a torque of
530 ± 70 N·m (391 ± 52 lb ft).
31. Install plugs (5) that hold the pins in the head. Tighten the plugs to a torque of 75 ± 7 N·m
(55 ± 5 lb ft).
12/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 28 g00624938
32. Install O-ring seals (2) and rings (3) on the displacement change valve.
Illustration 29 g00627438
33. Install displacement change valve (1) onto the head of the travel motor. Tighten the
displacement change valve to a torque of 50 ± 3 N·m (37 ± 2 lb ft).
34. To prevent possible damage to the travel motor, the unit should be filled with oil at least up
to the fill port prior to operation. Refer to Operation and Maintenance Manual for the
correct oil specification.
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 20 15:03:17 UTC+0800 2020
13/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D L EXCAVATOR KHS
Configuration: 349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile
Hydraulic Power Units Machine Systems
Media Number -RENR9574-10 Publication Date -01/08/2014 Date Updated -18/09/2018
i02429546
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Threaded Rod
M 20 X 2.5 by 18 inch
2
B 140-7742 Sleeve 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/2
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g01213930
Illustration 2 g01213930
1. Install Tooling (A) as a guide. Attach Tooling (B) and a suitable lifting device onto travel
motor (4). The weight of travel motor assembly (4) is approximately 127 kg (280 lb).
Position travel motor assembly (4) and install bolts (3).
Illustration 3 g01213929
2. Install bolts (2). Connect hose assemblies (1).
End By:
a. Install the counterbalance valve. Refer to Disassembly and Assembly, "Counterbalance
Valve (Travel) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 20 15:04:13 UTC+0800 2020
2/2
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D L EXCAVATOR KHS
Configuration: 349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile
Hydraulic Power Units Machine Systems
Media Number -RENR9574-10 Publication Date -01/08/2014 Date Updated -18/09/2018
i02429611
Final Drive and Travel Motor - Remove
SMCS - 4050-011; 4351-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A Block 1
B
1U-6221 Hydraulic Torque Wrench Assembly 1
132-8154 3/4 inch Square Drive Link 1
132-8223 Power Pack 1
C 138-7575 Link Bracket 2
Note: The final drive sprocket does not need to be removed prior to removal of the final drive.
The sprocket must be removed in order to disassemble the final drive.
Note: The procedure to remove the right hand final drive and the procedure to remove the left
hand final drive is identical. The procedure that follows is for one of the final drives.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Release track tension. Refer to Operation and Maintenance Manual, "Track Adjustment -
Adjust".
Illustration 1 g01213996
2. Start the machine and position track roller (1) on Tooling (A). Make sure that the pin for
separating the track is positioned over the final drive.
3. Separate the track. Refer to Disassembly and Assembly, "Track - Seperate".
4. Drain the final drive. Refer to Operation and Maintenance Manual, "Final Drive Oil -
Change".
5. Remove the counterbalance valve. Refer to Disassembly and Assembly, "Counterbalance
Valve - Remove and Install".
2/4
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g01214021
6. Attach two lifting slings and a suitable lifting device to final drive (2), as shown. It may be
necessary to adjust the lifting straps for correct balance of the final drive.
Illustration 3 g01214049
Illustration 4 g01214023
3/4
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 7. Disconnect hose assemblies (3). Remove fittings (4) and bolts (5).
8. Use Tooling (B) to remove bolts (5) and the washers that hold the final drive to the
undercarriage frame assembly. Carefully remove the final drive and the travel motor from
the undercarriage frame assembly. The combined weight of the final drive and the travel
motor is 725 kg (1600 lb).
Illustration 5 g01214002
9. Invert final drive assembly (6) onto the cover, as shown.
10. Attach Tooling (C) and a suitable lifting device in order to remove travel motor (6). The
weight of travel motor assembly (6) is approximately 127 kg (280 lb). Remove travel motor
assembly (6).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 20 15:05:09 UTC+0800 2020
4/4
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D L EXCAVATOR KHS
Configuration: 349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile
Hydraulic Power Units Machine Systems
Media Number -RENR9574-10 Publication Date -01/08/2014 Date Updated -18/09/2018
i05331566
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Stand Group 1
B 138-7573 Link Bracket 2
C 1P-1860 Retaining Ring Pliers 1
D 4C-8359 Eyebolt 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive and Travel Motor
- Remove" in this manual.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
1/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g01207795
2. Remove coupling (1) from final drive (2) .
3. Attach a suitable lifting device to the final drive, and turn final drive (2) over 180 degrees.
The weight of final drive (2) is approximately 590 kg (1300 lb).
Illustration 2 g01207796
4. Attach the final drive to Tooling (A) . Put an alignment mark across the sections of the final
drive for assembly purposes. All parts must be reinstalled in the original locations.
5. Remove socket head screws (3) from the final drive cover.
2/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 3 g01207801
6. Attach Tooling (B) and a suitable lifting device to cover (5) , as shown. The weight of cover
(5) is approximately 52 kg (115 lb).
7. Remove bolts (4) and the washers that hold the cover in place.
8. Use a soft faced hammer in order to break the seal between cover (5) and the ring gear.
Remove cover (5) . The weight of cover (5) is 52 kg (115 lb).
Illustration 4 g01207835
9. Remove spacer (6) from the cover.
3/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 5 g01207845
10. Remove shims (7) from the cover.
11. Remove socket head bolts (8) and ring gear (9) from the cover.
Illustration 6 g01207864
12. Remove sun gear (10) from carrier assembly (11) . Remove carrier assembly (11) by lifting
the carrier assembly straight up.
13. Disassemble carrier assembly (11) , as follows:
4/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
26. Illustration 7 g01207865
a. Remove spacers (12) . A spacer is located on each side of the sun gear in carrier
assembly (11) .
Note: Planetary gears (15) might be stamped with identification marks "L". Note the
position of the identification marks in relation to the carrier for assembly purposes.
Illustration 8 g01207897
b. Remove retaining ring (13) with Tooling (C) .
c. Remove thrust washers (14) and planetary gear (15) from the carrier.
d. Remove bearing (16) from the planetary gear.
e. Repeat Steps 13.b through 13.d for the other two planetary gears.
Illustration 9 g01208035
f. Use a screwdriver in order to remove retaining ring (17) from the carrier. Remove sun
gear (18) from the carrier.
5/13
349D L Excavators KHS00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...