The document provides instructions for assembling and disassembling a travel motor on an excavator. It describes 27 steps for assembling the travel motor, including installing seals, springs, pistons, bearings and other components in the proper order. 13 steps are listed for removing the final drive and travel motor assembly, which requires draining oil, disconnecting hoses, and removing bolts and couplings. Tools required for assembly and removal are also listed.
Caterpillar cat 336 e l excavator (prefix bmh) service repair manual (bmh0000...fjjskekdm
This document provides instructions for removing and installing a travel motor on an excavator. It outlines 28 steps to disassemble the travel motor, including removing seals, springs, pistons, and other components. It then describes 13 steps for installation, which involves reassembling these parts in reverse order and noting proper torque specifications for bolts. The final step states to install the travel motor by following the removal procedures in reverse order.
Caterpillar cat 336 e l excavator (prefix bmh) service repair manual (bmh0000...fjekkdmmem
This document provides instructions for disassembling and assembling components of a 336E excavator. It describes how to:
1. Remove and install the final drive and travel motor, which requires draining fluids, disconnecting hoses, and removing bolts.
2. Disassemble the final drive by removing the cover, gears, bearings, and other internal parts.
3. Assemble the travel motor by precisely installing seals, springs, pistons, and other components in the correct order and orientation.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing a travel motor on an excavator. It outlines 27 steps for disassembly, including draining oil, removing hoses and bolts, and using lifting devices to remove the final drive and travel motor assembly. The installation procedure is the reverse of removal, and specifies torques for bolts and using anti-seize compound on threads. The overall process involves carefully removing and reinstalling multiple components of the excavator's hydraulic system.
Caterpillar cat 336 e l excavator (prefix fjh) service repair manual (fjh0000...hfhjskedme
This document provides instructions for removing and installing a travel motor on an excavator. It outlines 27 steps for disassembly, including draining oil, removing hoses and bolts, and using lifting devices to remove the final drive and travel motor assembly. The installation procedure is the reverse of removal, and specifies torques for bolts and using a thread locking compound. The overall summary is that this provides detailed removal and installation instructions for an excavator travel motor, outlining over two dozen individual steps.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a travel motor and final drive. It details 27 steps to assemble the travel motor, including installing seals, springs, pistons, and other components in the proper order. It also outlines 13 steps to remove the final drive and travel motor as a unit from the excavator, and 10 steps to disassemble the final drive, removing components like gears, spacers, and covers. Personal protective equipment is recommended due to risk of injury from pressurized hydraulic fluid.
Caterpillar cat 336 e l excavator (prefix fjh) service repair manual (fjh0000...fjkkekmdm
The document provides instructions for disassembling and assembling a travel motor. It details 27 steps for assembling the travel motor that include installing seals, springs, pistons, and other components in the proper order and orientation. Thirteen steps are listed for disassembling the final drive and travel motor assembly, which include removing hoses, bolts, and separating the final drive from the travel motor. Safety precautions are provided regarding the use of lifting devices to handle heavy components and releasing hydraulic pressure before disassembly.
Caterpillar cat 336 e l excavator (prefix fjh) service repair manual (fjh0000...jfskemsemm
The document provides instructions for disassembling and assembling a travel motor and final drive. It details 27 steps to assemble the travel motor, including installing seals, springs, pistons, and other components in the proper order. It also outlines 13 steps to remove the final drive and travel motor as a unit from the excavator, and 10 steps to disassemble the final drive, removing components like gears, spacers, and covers. Personal protective equipment is recommended due to risk of injury from pressurized hydraulic fluid.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...ze3xiandiao
This document provides instructions for removing and installing a travel motor on an excavator. It outlines 27 steps for disassembly, including draining oil, removing hoses and bolts, and using lifting devices to remove the final drive and travel motor assembly. The installation procedure is the reverse of removal, and specifies torques for bolts and using anti-seize compound on threads. The overall process involves carefully removing and reinstalling multiple components of the excavator's hydraulic system.
Caterpillar cat 336 e l excavator (prefix bmh) service repair manual (bmh0000...fjjskekdm
This document provides instructions for removing and installing a travel motor on an excavator. It outlines 28 steps to disassemble the travel motor, including removing seals, springs, pistons, and other components. It then describes 13 steps for installation, which involves reassembling these parts in reverse order and noting proper torque specifications for bolts. The final step states to install the travel motor by following the removal procedures in reverse order.
Caterpillar cat 336 e l excavator (prefix bmh) service repair manual (bmh0000...fjekkdmmem
This document provides instructions for disassembling and assembling components of a 336E excavator. It describes how to:
1. Remove and install the final drive and travel motor, which requires draining fluids, disconnecting hoses, and removing bolts.
2. Disassemble the final drive by removing the cover, gears, bearings, and other internal parts.
3. Assemble the travel motor by precisely installing seals, springs, pistons, and other components in the correct order and orientation.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing a travel motor on an excavator. It outlines 27 steps for disassembly, including draining oil, removing hoses and bolts, and using lifting devices to remove the final drive and travel motor assembly. The installation procedure is the reverse of removal, and specifies torques for bolts and using anti-seize compound on threads. The overall process involves carefully removing and reinstalling multiple components of the excavator's hydraulic system.
Caterpillar cat 336 e l excavator (prefix fjh) service repair manual (fjh0000...hfhjskedme
This document provides instructions for removing and installing a travel motor on an excavator. It outlines 27 steps for disassembly, including draining oil, removing hoses and bolts, and using lifting devices to remove the final drive and travel motor assembly. The installation procedure is the reverse of removal, and specifies torques for bolts and using a thread locking compound. The overall summary is that this provides detailed removal and installation instructions for an excavator travel motor, outlining over two dozen individual steps.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a travel motor and final drive. It details 27 steps to assemble the travel motor, including installing seals, springs, pistons, and other components in the proper order. It also outlines 13 steps to remove the final drive and travel motor as a unit from the excavator, and 10 steps to disassemble the final drive, removing components like gears, spacers, and covers. Personal protective equipment is recommended due to risk of injury from pressurized hydraulic fluid.
Caterpillar cat 336 e l excavator (prefix fjh) service repair manual (fjh0000...fjkkekmdm
The document provides instructions for disassembling and assembling a travel motor. It details 27 steps for assembling the travel motor that include installing seals, springs, pistons, and other components in the proper order and orientation. Thirteen steps are listed for disassembling the final drive and travel motor assembly, which include removing hoses, bolts, and separating the final drive from the travel motor. Safety precautions are provided regarding the use of lifting devices to handle heavy components and releasing hydraulic pressure before disassembly.
Caterpillar cat 336 e l excavator (prefix fjh) service repair manual (fjh0000...jfskemsemm
The document provides instructions for disassembling and assembling a travel motor and final drive. It details 27 steps to assemble the travel motor, including installing seals, springs, pistons, and other components in the proper order. It also outlines 13 steps to remove the final drive and travel motor as a unit from the excavator, and 10 steps to disassemble the final drive, removing components like gears, spacers, and covers. Personal protective equipment is recommended due to risk of injury from pressurized hydraulic fluid.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...ze3xiandiao
This document provides instructions for removing and installing a travel motor on an excavator. It outlines 27 steps for disassembly, including draining oil, removing hoses and bolts, and using lifting devices to remove the final drive and travel motor assembly. The installation procedure is the reverse of removal, and specifies torques for bolts and using anti-seize compound on threads. The overall process involves carefully removing and reinstalling multiple components of the excavator's hydraulic system.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual (FJH00001...jdkskmmdmd1
The document provides instructions for disassembling and assembling a travel motor and final drive. It details 27 steps to assemble the travel motor, including installing seals, springs, pistons, and other components in the proper order. It also outlines 13 steps to remove the final drive and travel motor as a unit from the excavator, and 10 steps to disassemble the final drive, removing components like gears, spacers, and covers. Personal protective equipment is recommended due to risk of injury from pressurized hydraulic fluid.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor. It details 27 steps for assembling the travel motor that include installing seals, springs, pistons, and other components in the proper order and orientation. Thirteen steps are listed for disassembling the final drive, which include removing the cover, gears, and planetary gear assembly. Personal injury warnings are provided and all components must be cleaned before assembly.
Caterpillar cat 336 e l excavator (prefix fjh) service repair manual (fjh0000...fjskekmdm
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Removing hoses, covers, and bolts to separate the final drive and travel motor assembly from the excavator frame.
2) Using lifting devices to remove the assembly and travel motor, which weigh 860kg and 184kg respectively.
3) Reversing the removal procedures to reinstall the components, applying locking agents and torquing bolts to the specified values.
Caterpillar cat 336 e l excavator (prefix fjh) service repair manual (fjh0000...fjsekqazxkdmmem
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Removing hoses, covers, and bolts to separate the final drive and travel motor assembly from the excavator frame.
2) Using lifting devices to remove the assembly and travel motor, which weigh 860kg and 184kg respectively.
3) Reversing the removal procedures to reinstall the components, applying locking agents and torquing bolts to the specified values.
Caterpillar Cat 336E L Excavator (Prefix YEP) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing the final drive and travel motor assembly.
2) Attaching lifting equipment and removing bolts to separate the travel motor from the final drive and remove the assemblies.
3) Reversing the process to install the travel motor onto the final drive and reinstall the assembled unit along with hydraulic connections.
Caterpillar cat 336 e l excavator (prefix yep) service repair manual (yep0000...fjkkekmdm
This document provides instructions for disassembling and assembling the travel motor and final drive components of an excavator. The disassembly process involves removing the cover, plate, sun gear, spacer, planetary gear assembly, retaining ring, washer and planetary gear. The assembly process details installing these components in reverse order and applying the specified torques to the fasteners. Safety precautions are provided to prevent injury when working with pressurized hydraulic systems and spring-loaded components.
Caterpillar Cat 336E L Excavator (Prefix YEP) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the travel motor and final drive components of an excavator. The disassembly process involves removing the cover, plate, sun gear, spacer, planetary gear assembly, retaining ring, washer and planetary gear. The assembly process details installing these components in reverse order and applying the specified torques to the fasteners. Safety precautions are provided to prevent injury when working with pressurized hydraulic systems and spring-loaded components.
Caterpillar cat 336 e l excavator (prefix yep) service repair manual (yep0000...hfhjskedme
This document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic lines before removal.
2) Using lifting equipment to remove the final drive and travel motor assembly, travel motor, and coupling.
3) Cleaning and lubricating parts before reverse installation, and torquing bolts to the specified values.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...jdkskmdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using tools to install the bushing, idler shaft, idler gear, thrust plate, washer, and idler gear bolt while ensuring proper gear alignment and backlash. Tolerances for backlash and clearances are provided.
This document provides instructions for disassembling and assembling the travel motor of 324E and 324E LN excavators. The disassembly process involves removing 28 components from the travel motor in 27 steps. The assembly process reverses the disassembly with 28 steps and provides guidance on cleaning, lubricating, and installing components in the correct orientation. Tools required include retaining ring pliers, drivers, pullers, and adapters to securely hold components during disassembly and assembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations guide removal of additional components like the flywheel housing, crankshaft pulley, and crankshaft front seal. Tools and safety precautions are also listed.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, counterbalance valve housing assembly, and more. Safety notices are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, wrenches, and other equipment.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...jdkskmdmdm
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like bolts, covers, seals, springs, pistons, gears, and bearings. The corresponding 51 steps for assembly install these same components in reverse order, noting the tools required and proper installation of seals, bearings, and retaining rings. Precautions are included for released spring forces during disassembly and heating components during assembly.
Caterpillar Cat 330F L Excavator (Prefix GHT) Service Repair Manual (GHT00001...jdkskmdmdm
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and ensuring fluids are contained.
This document provides assembly instructions for repairing a hydraulic pump in 3 steps:
1. Install various internal components like bearings, seals, and pistons into the pump housing.
2. Attach the pump housing to the pump head and install additional external components.
3. Assemble the pump control mechanism by installing springs, pistons, and covers.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing using specialized tools over 30 detailed steps. Cleanliness is emphasized throughout to prevent dirt contamination during reassembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1. The flywheel, flywheel housing, crankshaft rear seal, and vibration damper and pulley. Tools and torque specifications are listed for each procedure.
2. Removing the crankshaft rear seal involves drilling holes in the seal and pulling it out with a slide hammer tool. Installing the new seal uses a seal installation tool.
3. Removing the flywheel housing first requires removing mounting bolts and the flywheel. Installing applies sealant and mounts the housing with bolts.
4. Instructions are provided to remove the crankshaft front
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precise tools and cleaning of parts is emphasized.
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs technicians to clean all parts thoroughly, apply lubricants where specified, and install over 30 parts into the final drive housing in the reverse order of disassembly using various tools. Technicians are advised to replace all seals, gaskets and O-rings during assembly and to keep all parts clean.
The document provides instructions for disassembling and assembling the piston motor (hydraulic fan) on 325C and 325C L excavator models. The disassembly procedure involves 22 steps to remove components like the key, cover, port plate, bearings, plugs, sleeves, pistons and housing. The assembly procedure describes 16 steps including pressing components, installing seals, pins and rings in the proper order and orientation to rebuild the piston motor. Cleanliness and applying a light oil film to parts is emphasized throughout.
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
More Related Content
Similar to Caterpillar Cat 336E L Excavator (Prefix BMH) Service Repair Manual (BMH00001 and up).pdf
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual (FJH00001...jdkskmmdmd1
The document provides instructions for disassembling and assembling a travel motor and final drive. It details 27 steps to assemble the travel motor, including installing seals, springs, pistons, and other components in the proper order. It also outlines 13 steps to remove the final drive and travel motor as a unit from the excavator, and 10 steps to disassemble the final drive, removing components like gears, spacers, and covers. Personal protective equipment is recommended due to risk of injury from pressurized hydraulic fluid.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor. It details 27 steps for assembling the travel motor that include installing seals, springs, pistons, and other components in the proper order and orientation. Thirteen steps are listed for disassembling the final drive, which include removing the cover, gears, and planetary gear assembly. Personal injury warnings are provided and all components must be cleaned before assembly.
Caterpillar cat 336 e l excavator (prefix fjh) service repair manual (fjh0000...fjskekmdm
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Removing hoses, covers, and bolts to separate the final drive and travel motor assembly from the excavator frame.
2) Using lifting devices to remove the assembly and travel motor, which weigh 860kg and 184kg respectively.
3) Reversing the removal procedures to reinstall the components, applying locking agents and torquing bolts to the specified values.
Caterpillar cat 336 e l excavator (prefix fjh) service repair manual (fjh0000...fjsekqazxkdmmem
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Removing hoses, covers, and bolts to separate the final drive and travel motor assembly from the excavator frame.
2) Using lifting devices to remove the assembly and travel motor, which weigh 860kg and 184kg respectively.
3) Reversing the removal procedures to reinstall the components, applying locking agents and torquing bolts to the specified values.
Caterpillar Cat 336E L Excavator (Prefix YEP) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing the final drive and travel motor assembly.
2) Attaching lifting equipment and removing bolts to separate the travel motor from the final drive and remove the assemblies.
3) Reversing the process to install the travel motor onto the final drive and reinstall the assembled unit along with hydraulic connections.
Caterpillar cat 336 e l excavator (prefix yep) service repair manual (yep0000...fjkkekmdm
This document provides instructions for disassembling and assembling the travel motor and final drive components of an excavator. The disassembly process involves removing the cover, plate, sun gear, spacer, planetary gear assembly, retaining ring, washer and planetary gear. The assembly process details installing these components in reverse order and applying the specified torques to the fasteners. Safety precautions are provided to prevent injury when working with pressurized hydraulic systems and spring-loaded components.
Caterpillar Cat 336E L Excavator (Prefix YEP) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the travel motor and final drive components of an excavator. The disassembly process involves removing the cover, plate, sun gear, spacer, planetary gear assembly, retaining ring, washer and planetary gear. The assembly process details installing these components in reverse order and applying the specified torques to the fasteners. Safety precautions are provided to prevent injury when working with pressurized hydraulic systems and spring-loaded components.
Caterpillar cat 336 e l excavator (prefix yep) service repair manual (yep0000...hfhjskedme
This document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic lines before removal.
2) Using lifting equipment to remove the final drive and travel motor assembly, travel motor, and coupling.
3) Cleaning and lubricating parts before reverse installation, and torquing bolts to the specified values.
Similar to Caterpillar Cat 336E L Excavator (Prefix BMH) Service Repair Manual (BMH00001 and up).pdf (8)
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...jdkskmdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using tools to install the bushing, idler shaft, idler gear, thrust plate, washer, and idler gear bolt while ensuring proper gear alignment and backlash. Tolerances for backlash and clearances are provided.
This document provides instructions for disassembling and assembling the travel motor of 324E and 324E LN excavators. The disassembly process involves removing 28 components from the travel motor in 27 steps. The assembly process reverses the disassembly with 28 steps and provides guidance on cleaning, lubricating, and installing components in the correct orientation. Tools required include retaining ring pliers, drivers, pullers, and adapters to securely hold components during disassembly and assembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations guide removal of additional components like the flywheel housing, crankshaft pulley, and crankshaft front seal. Tools and safety precautions are also listed.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, counterbalance valve housing assembly, and more. Safety notices are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, wrenches, and other equipment.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...jdkskmdmdm
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like bolts, covers, seals, springs, pistons, gears, and bearings. The corresponding 51 steps for assembly install these same components in reverse order, noting the tools required and proper installation of seals, bearings, and retaining rings. Precautions are included for released spring forces during disassembly and heating components during assembly.
Caterpillar Cat 330F L Excavator (Prefix GHT) Service Repair Manual (GHT00001...jdkskmdmdm
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and ensuring fluids are contained.
This document provides assembly instructions for repairing a hydraulic pump in 3 steps:
1. Install various internal components like bearings, seals, and pistons into the pump housing.
2. Attach the pump housing to the pump head and install additional external components.
3. Assemble the pump control mechanism by installing springs, pistons, and covers.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing using specialized tools over 30 detailed steps. Cleanliness is emphasized throughout to prevent dirt contamination during reassembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1. The flywheel, flywheel housing, crankshaft rear seal, and vibration damper and pulley. Tools and torque specifications are listed for each procedure.
2. Removing the crankshaft rear seal involves drilling holes in the seal and pulling it out with a slide hammer tool. Installing the new seal uses a seal installation tool.
3. Removing the flywheel housing first requires removing mounting bolts and the flywheel. Installing applies sealant and mounts the housing with bolts.
4. Instructions are provided to remove the crankshaft front
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precise tools and cleaning of parts is emphasized.
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs technicians to clean all parts thoroughly, apply lubricants where specified, and install over 30 parts into the final drive housing in the reverse order of disassembly using various tools. Technicians are advised to replace all seals, gaskets and O-rings during assembly and to keep all parts clean.
The document provides instructions for disassembling and assembling the piston motor (hydraulic fan) on 325C and 325C L excavator models. The disassembly procedure involves 22 steps to remove components like the key, cover, port plate, bearings, plugs, sleeves, pistons and housing. The assembly procedure describes 16 steps including pressing components, installing seals, pins and rings in the proper order and orientation to rebuild the piston motor. Cleanliness and applying a light oil film to parts is emphasized throughout.
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
This document provides instructions for removing and installing various components of the crankshaft and flywheel housing on a 325C Excavator. It describes how to remove and install the flywheel, crankshaft rear seal, rear seal carrier, and flywheel housing. The procedures include lists of required tools and step-by-step instructions describing how to remove each component and install the replacement parts. Safety notices are provided to keep parts clean and contain fluids appropriately during the repair work.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...jdkskmdmdm
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists the required tools and outlines 16 steps to disassemble parts like the traction control valve, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
1) The document provides disassembly instructions for components of a 313D excavator including the final drive, travel motor, counterbalance valve, and traction control valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification marks and order of components.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, plates, and seals. Proper handling and storage of fluids is also addressed.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...jdkskmdmdm
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, installing new gaskets, and tightening bolts in a specific sequence using torque wrenches and degree wheels to ensure proper torque.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...jdkskmdmdm
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E L EXCAVATOR BMH
Configuration: 336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15).
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15).
Note: Bearing race (18) must contact retaining ring (17).
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16).
17. Place the pump housing into Tooling (A).
6/10
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g02107957
18. Use Tooling (C) to install rotating assembly (16) into the housing.
Illustration 15 g00887501
Illustration 16 g02107975
19. The notches in cam plate (20) must align with keys (26). The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
7/10
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8).
24. Install brake piston (8) into the housing so that the cast mark on brake piston (8) is aligned
with the brake supply passage in the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level to
prevent damage to the O-ring seals.
8/10
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6).
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5).
Illustration 22 g00887295
9/10
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 13 19:40:56 UTC+0800 2020
10/10
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E L EXCAVATOR BMH
Configuration: 336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i07191698
Final Drive and Travel Motor - Remove and Install
SMCS - 4050; 4351
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change" for the correct
draining and filling procedures.
1/5
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g02108761
2. Remove bolts (1) and cover (2).
3. Separate the track.
Illustration 2 g02108762
4. Disconnect hose assemblies (3) ( 4), and (6). Remove fitting (5).
2/5
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g02108781
5. Attach Tooling (A) and a suitable lifting device to final drive and travel motor (7). The
weight of final drive and travel motor (7) is approximately 860 kg (1896 lb). Put a slight
lifting tension on final drive and travel motor (7).
Illustration 4 g02108790
Note: Mark the orientation of the final drive and travel motor assembly for installation
purposes.
6. Remove bolts (8).
Illustration 5 g02108791
7. Use two bolts (8) to remove final drive and travel motor (7).
8. Carefully remove final drive and travel motor (7).
9. Remove bolts (8) from the frame.
3/5
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 6 g02108793
10. Remove bolts (9), counterbalance valve (10), and the O-ring seals.
Illustration 7 g02108794
11. Attach Tooling (B) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 84 kg (185 lb).
12. Remove four bolts (12) and travel motor (11) from final drive (13).
4/5
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 8 g02108914
13. Remove coupling (14).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
C - Loctite C5A Copper Anti-Seize -
1. Before assembly remove all compounds, oil, and dust.
2. Install final drive and travel motor (7) in the reverse order of removal.
a. Tighten bolts (9) to a torque of 80 ± 8 N·m (60 ± 6 lb ft).
b. Apply Tooling (C) to the threads of bolt (8).
c. Tighten bolts (8) to a torque of 250 ± 25 N·m (184 ± 18 lb ft) and turn an additional
angle of 45 ± 5 degrees. Refer to Service Magazine, M0083843, "An Improved Bolt
Tightening Procedure for the Critical Joints Is Now Used on All Excavators" for more
detail information.
d. Tighten hose assembly (3) to a torque of 160 ± 16 N·m (120 ± 12 lb ft).
e. Tighten bolts (1) to a torque of 130 ± 10 N·m (95 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 13 19:41:52 UTC+0800 2020
5/5
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E L EXCAVATOR BMH
Configuration: 336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i03885522
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 154-6183 Forcing Bolts 3
C 138-7576 Link Brackets 3
Start By:
a. Remove the final drive and the travel motor.
Illustration 1 g02131413
1/8
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 1. Attach Tooling (A) and a suitable lifting device to cover (2). The weight of cover (2) is
approximately 20 kg (45 lb). Remove bolts (1) and cover (2).
Illustration 2 g02131414
2. Remove plate (3) from cover (2).
Illustration 3 g02131415
3. Remove sun gear (4), spacer (5), and planetary gear assembly (6).
2/8
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 4 g02131875
4. Remove retaining ring (7), washer (8), planetary gear (9), roller bearing (11), and washer
(12) from carrier assembly (13).
5. Remove retaining ring (10) and sun gear (14) from carrier assembly (13).
Illustration 5 g02131876
6. Remove spacer (16).
7. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (15). The weight
of planetary gear assembly (15) is approximately 32 kg (70 lb). Remove planetary gear
assembly (15).
3/8
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 6 g02131877
8. Drive spring pin (17) into planetary shaft (18) with a suitable hammer and a suitable punch.
9. Remove planetary shaft (18), washer (20), roller bearing (20), planetary gear (23), and
washer (24) from the carrier assembly (21).
10. Remove spring pin (17) from planetary shaft (18) with a suitable hammer and a suitable
punch.
11. Remove retaining ring (19) and sun gear (25) from carrier assembly (21).
Illustration 7 g02131878
12. Remove spacer (26).
13. Attach Tooling (A) and a suitable lifting device to ring gear (27). The weight of ring gear
(27) is approximately 70 kg (155 lb). Remove bolts (28) and ring gear (27).
4/8
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 8 g02131879
14. Remove O-ring seal (29).
15. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (30). The weight
of planetary gear assembly (30) is approximately 57 kg (125 lb). Remove planetary gear
assembly (30).
Illustration 9 g02131881
16. Drive spring pin (31) into planetary shaft (32) with a suitable hammer and a suitable punch.
17. Remove planetary shaft (32), washer (33), roller bearings (35), planetary gear (36), and
washer (36) from the carrier assembly (34).
18. Remove spring pin (31) from planetary shaft (32) with a suitable hammer and a suitable
punch.
5/8
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 10 g02131882
Illustration 11 g02131885
19. Remove bolts (38). Use Tooling (B) in order to remove gear (39).
Illustration 12 g02131886
20. Remove shims (40).
6/8
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 13 g02131887
21. Attach Tooling (C) and a suitable lifting device to sprocket housing (41). The weight of
sprocket housing (41) is approximately 107 kg (235 lb). Remove sprocket housing (41) and
roller bearing (42).
Illustration 14 g02131888
22. Remove bearing races (43) and Duo-Cone seal (44) from sprocket housing (41).
7/8
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 15 g02132155
23. Remove Duo-Cone seal (45) and roller bearing (47) from motor housing (48). The weight of
motor housing (48) is approximately 91 kg (200 lb).
24. If necessary, remove dowels (46) from motor housing (48).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 13 19:42:48 UTC+0800 2020
8/8
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E L EXCAVATOR BMH
Configuration: 336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i05103849
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 154-6183 Forcing Bolts 3
C 138-7576 Link Brackets 3
D 5P-3931 Anti-Seize Compound -
E 1U-9895 Crossblock 1
F 6V-2012 Depth Micrometer 1
G 6V-7059 Micrometer () 1
H - Loctite 242 -
J 6V-2055 Grease -
K - Loctite 17430 -
L 8T-9206 Seal Installer 1
1/12
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g02132155
1. Apply Tooling (D) to the surface of dowels (46) . Install dowels (46) .
2. Raise the temperature of roller bearing (47) . Install the roller bearing (47) on motor housing
(48) .
3. Install Duo-Cone seal (45) .
Illustration 2 g02131888
4. Lower the temperature of bearing races (43) . Install bearing races (43) in sprocket housing
(41) .
5. Install Duo-Cone seal (44) .
2/12
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Illustration 3 g02131887
6. Attach Tooling (C) and a suitable lifting device to sprocket housing (41) . The weight of
sprocket housing (41) is approximately 107 kg (235 lb). Install sprocket housing (41) .
7. Raise the temperature of roller bearing (42) . Install the roller bearing (42) .
Illustration 4 g02135728
3/12
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 5 g02134214
8. Use Tooling (E) and a suitable press in order to apply force to roller bearing (42) . Apply a
force of 4000 kg (8818 lb) to the top of Tooling (E) . Rotate sprocket housing (41) in order
to seat the roller bearings.
9. Reduce the force on top of Tooling (E) to 3000 ± 300 kg (6614 ± 661 lb). Use Tooling (F)
in order to measure Dimension (X) . Record Dimension (X) .
4/12
336E L Excavators BMH00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...